Electron beam synthesis and characterization of poly(vinyl alcohol)/montmorillonite nanocomposites

Poly(vinyl alcohol) (PVA)/montmorillonite clay (MMT) nanocomposites in the form of films were prepared under the effect of electron beam irradiation. The PVA/MMT nanocomposites gels were characterized by X‐ray diffraction (XRD), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and mechanical measurements. The study showed that the appropriate dose of electron beam irradiation to achieve homogeneous nanocomposites films and highest gel formation was 20 kGy. The introduction of MMT (up to 4 wt %) results in improvement in tensile strength, elongation at break, and thermal stability of the PVA matrix. In addition, the intercalation of PVA with the MMT clay leads to an impressive improved water resistance, indicating that the clay is well dispersed within the polymer matrix. Meanwhile, it was proved that the intercalation has no effect on the metal uptake capability of PVA as determined by a method based on the color measurements. XRD patterns and SEM micrographs suggest the coexistence of exfoliated intercalated MMT layers over the studied MMT contents. The DSC thermograms showed clearly that the intercalation of PVA polymer with these levels of MMT has no influence on the melting transitions; however, the glass transition temperature (T_g) for PVA was completely disappeared, even at low levels of MMT clay. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1129–1138, 2006     

聚乙二醇/氧化锑锡纳米复合纤维结构及保温透气性能

功能户外防护材料中热能管理是一个重要的方面。对于功能织物开发而言，大都采用涂层后整理技术，但是其功能性和透气性的平衡是关键。本文以静电纺丝技术制备了聚乙二醇/氧化锑锡（PVA/ATO）纳米复合纤维膜，采用扫描电镜（SEM）、傅里叶红外光谱（FTIR）、X射线衍射（XRD）、热重（TG）对纳米复合纤维进行了表征，并对PVA/ATO/黏胶热轧复合材料的保温性能及透气性进行了测试。结果表明：PVA中ATO具有良好的分散性，部分ATO纳米颗粒镶嵌在纤维表面。PVA/ATO/黏胶热轧复合材料的保温率相对于基材黏胶热轧布提高了28.9%，达到37.1%，相应传热系数为12.62W/m²·℃，克罗值0.32。ATO纳米颗粒的加入可以直接改善PVA纳米纤维膜的堆积结构，使得PVA/ATO/黏胶热轧复合材料的透气性相对于PVA/黏胶热轧复合材料有明显提高，但趋势随纳米纤维层厚度的增加而降低。PVA/ATO纳米复合膜可以复合到多种基材上，从而为基于纳米纤维功能材料开发保温透气功能提供了思路。     

Electrospinning fabrication and characterization of poly(vinyl alcohol)/waterborne polyurethane nanofiber membranes in aqueous solution

Poly(vinyl alcohol) (PVA)/waterborne polyurethane (WBPU) nanofiber mats were prepared using electrospinning method with aqueous solutions. Scanning electron microscopy (SEM), X‐ray diffraction (XRD), thermal gravimetric analyzer (TGA), and tensile strength testing machine (ZWICK) were used to characterize the morphology and properties of the PVA/WBPU nanofiber mats. The results showed that the morphologies of PVA/WBPU nanofiber mats changed with the total solid concentration and the mass ratio of PVA/WBPU in the spinning solution. The tensile strength and thermal stability of the fibers could be significantly affected by the WBPU contents. The electrospun PVA/WBPU membranes showed higher water uptake, which would have potential applications in wound dressings. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation and properties of poly(vinyl alcohol)-clay nanocomposite materials

A series of polymer-clay nanocomposite (PCN) materials that consist of poly(vinyl alcohol) (PVA) and layered montmorillonite (MMT) clay are prepared by effectively dispersing the inorganic nanolayers of MMT clay in organic PVA matrix via an in situ free radical polymerization with AIBN as initiator. Organic vinyl acetate monomers are first intercalated into the interlayer regions of organophilic clay hosts and followed by a one-step free radical polymerization. The prepared poly(vinyl acetate)-clay (PVAc-clay) solution are then saponified via direct-hydrolysis with NaOH solution to form PVA-clay nanocomposite materials. The as-synthesized PCN materials are typically characterized by Fourier-Transformation infrared (FTIR) spectroscopy, wide-angle X-ray diffraction and transmission electron microscopy.The molecular weights of poly(vinyl alcohol) (PVA) extracted from polymer-clay nanocomposite (PCN) materials and bulk PVA are determined by gel permeation chromatography (GPC) analysis with THF as eluant. The viscosity property of PCN materials with different feeding amount of MMT clay is studied by an ubbelohode capillary viscometer. The morphological image of as-synthesized materials is studied by scanning electron microscopy (SEM) and optical polarizing microscope (OPM). Effects of the material composition on the thermal stability, mechanical strength, optical clarity of PVA along with a series of PCN materials, in the form of fine powder and free-standing film, are also studied by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), dynamic mechanical analyzer (DMA) and UV-visible transmission spectra, respectively.     

Novel high-strength montmorillonite/polyvinyl alcohol composite film enhanced by chitin nanowhiskers

Nanomaterials can be used as reinforcement phase to improve the performance of polymers. A simple method to prepare a composite film with super high tensile strength was used in this study. The properties of montmorillonite (MMT)/polyvinyl alcohol (PVA) films reinforced by chitin nanowhisker (CNW) have been evaluated. The structures and properties of films were analyzed by atomic force microscope (AFM), Fourier transforms infrared spectroscopy (FT-IR), X-ray diffraction (XRD), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and tensile testing. The results of FTIR and XRD showed that no chemical interaction occurred among MMT, PVA, and CNW. The SEM and AFM images suggested that the obtained composite films with the three substances had a relatively uniform layered structure and relatively smooth. The temperature at the onset of decomposition of the composite films was increased from 262.0 to 282.3°C by the addition of CNW. The tensile strength of the MMT/PVA/CNW film was reached 263.5 MPa, which was increased approximately 382% compared with the MMT/PVA film. According to these results, the composite film could be potentially used in packaging materials.     

Synthesis and characterization of some polyacrylate/montmorillonite nanocomposites by in situ emulsion polymerization using redox initiation system

Intercalated modification of Montmorillonite clay (MMT) with three different amino acids—Alanine, Leucine, and Phenylalanine—in the presence of hydrochloric acid followed by surface modification by methyl triethoxy silane coupling agent to produce double modified Montmorillonite clay which is characterized by X‐ray diffraction (XRD) and Thermogravimetric analysis (TGA). The data shows an increase in d‐spacing of modified clay as a result of cationic exchange. Double modified MMT clay was used in the preparation of Polyacrylate/clay nanocomposites by using an in situ redox emulsion polymerization of polyglycidylmethacrylate (PGMA) and polymethylmethacrylate (PMMA). The structure and properties of the prepared nanocomposites were achieved by XRD, TGA, and SEM. The results show that all weight loses temperatures for the nanocomposite samples are higher than that of pure polymer in both PGMA and PMMA. It is also obvious that the increasing in the clay content plays an effective role in the increasing of thermal stability of these materials. SEM shows that the clay is more homogenously dispersed in PMMA than in PGMA matrix. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Abrasion studies of nylon 6/montmorillonite nanocomposites using scanning electron microscopy,fourier transform infrared spectroscopy,and X‐ray photoelectron spectroscopy

In this article, abrasion performance of commercial nylon 6 and nylon 6/montmorillonite (MMT) nanocomposites was studied. The polymer nanocomposites showed poor abrasion resistance compared to the neat polymer. The wear loss increased linearly with clay concentration. Changes in surface morphology, composition, and structure were investigated by scanning electron microscopy (SEM), Fourier transform infrared (FTIR)‐attenuated total reflection spectroscopy, and X‐ray photoelectron spectroscopy (XPS). SEM images showed that all the abraded surfaces contained fractured particles. However, the abraded nanocomposite surfaces had much deeper grooves compared to the homopolymer. FTIR results showed an increase in the amount of α crystals and a decrease in the amount of γ crystals on all the surfaces after abrasion. This was attributed to the strain‐induced γ to α crystal transformation. The largest amount of α crystals was formed in the abraded surface of pure nylon 6, and the amount of α crystals formed decreased with increasing MMT content. XPS results showed an increase in the [Si]/[N] elemental ratio for all nanocomposites after abrasion, indicating an increase in the clay content of the surface. Abrasive wear mechanism is as follows: (1) tensile tearing is the dominant wear mechanism for all the samples; (2) the cutting mechanism becomes more important when MMT content increases; (3) the polymer matrix is easier to be removed than clay during the abrasion process; (4) in nylon 6/MMT systems, the poor abrasion resistance is attributed to defects at the clay‐polymer interface, resulting in greater wear of the polymer matrix. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Electrolytic admicellar polymerization of pyrrole on natural rubber/clay nanocomposites

Organic–inorganic composites consisting of natural rubber (NR), polypyrrole (PPy), and sodium montmorillonite (Na‐MMT) were synthesized via electrolytic admicellar polymerization. A constant potential of 9 volts was chosen for the synthesis. The PPy concentration was fixed at 100 mM, and the clay contents were varied from 1 to 7 parts per hundred of rubber (phr). The synthesized nanocomposites were characterized by Fourier transform infrared spectroscopy (FTIR), X‐ray diffraction (XRD), scanning electron microscopy, and transmission electron microscopy (TEM), together with thermal stability (TGA), mechanical properties, and electrical conductivity (σ_dc) studies. The FTIR spectra indicated the characteristic peaks of both PPy and MMT clay and also evidenced a slight interaction between the PPy chain and the clay layers, verifying the success of electrolytic admicellar polymerization. XRD and TEM results pointed out the good dispersion of clay platelets in the polymer matrix, suggesting an exfoliated structure. The morphology of the nanocomposites was greatly dependent on the amount of MMT clay, especially at a 7 phr loading. The initial modulus and tensile strength of the nanocomposites containing the 7 phr loading were about four and two times higher, compared with unfilled NR/PPy, respectively. Thermal stability studies revealed a slight improvement in the decomposition temperature for the PPy component by the clay layers, whereas the opposite trend was found for the NR component. More interestingly, the electrical conductivity of the admicelled rubber increased significantly (～ 19–32 times) with increasing clay contents from 1 to 7 phr, in comparison with unfilled NR/PPy. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Structure‐property and swelling behavior of electron beam irradiated poly(vinyl alcohol)/acrylamide/sodium montmorillonite clay composites

Composites based on poly(vinyl alcohol) (PVA), acrylamide monomer (AM) and sodium montmorillonite clay (MMT) were prepared, in the form of thin films, by solution casting. The PVA/AM/MMT composites films were then exposed to electron beam irradiation to form crosslinked network structure. The structure‐property behavior of PVA/AM/MMT hybrids was demonstrated by x‐ray diffraction (XRD), scanning electron microscopy, gel content, color intensity, thermogravimetric analysis (TGA) and swelling behavior in aqueous solutions. The results indicated that the introduction of MMT clay ratio up to 5% decreased the gel content of PVA/AM hydrogels. The color measurements indicated that the introduction of MMT clay ratio up to 5% was shown to affect the color intensity of composite films. It was found that both PVA/AM hydrogels and PVA/AM/MMT composites reached the equilibrium swelling state in water after four hours; however PVA/AM/MMT composites displayed higher swelling than PVA/AM hydrogels. However, the swelling of PVA/AM hydrogels or their composites at the equilibrium state increased with increasing temperature up to 60°C. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and characterization of montmorillonite/polypyrrole nanocomposite

A novel montmorillonite (MMT)/polypyrrole (PPy) nanocomposite (MPN) with high electrical conductivity and thermal stability has been synthesized via in‐situ polymerization. The surface morphology, characterization, thermal stability, and electrical conductivity have been tested by scanning electron microscopy (SEM), Fourier‐transform infrared spectroscopy (FTIR), X‐ray diffraction (XRD), thermogravimetric analysis (TGA), and four‐probe methods, respectively. SEM results show that the antenna‐like PPy deposits on the layer surface of MMT. FTIR and XRD analyses show that there is interaction between MMT and PPy. The nanocomposite has high electrical conductivity (4 S/cm), eight orders of magnitude higher than that of pristine MMT. The thermal stability of MPN is higher than the pure PPy as well as the mixture of MMT and PPy (MMP). POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

加盐提高聚乙烯醇纳米纤维膜的力学和热稳定性能

对含有NaCl、KCl、Na2SO4、Na2CO3的聚乙烯醇(PVA)溶液进行静电纺丝,成功制备出含盐PVA纳米纤维膜。通过扫描电子显微镜(SEM)对各纤维膜的形貌进行表征,发现这些无机盐的加入对PVA纳米纤维的形貌造成明显影响,如纤维之间发生粘连或扁平带状纤维。此外通过单轴拉伸对各纤维膜的力学性能进行测试,结果表明:少量NaCl、KCl、Na2SO4或Na2CO3的加入,可以明显提高PVA纳米纤维膜的力学性能。进一步通过热失重分析(TGA)对各纤维膜热稳定性的考察表明:NaCl、KCl、Na2SO4的加入可以有效提高PVA纳米纤维膜的热稳定性,而Na2CO3的加入则对PVA纳米纤维膜的热稳定性无明显提高。     

Synthesis and characterization of polyurethane/bentonite nanoclay based nanocomposites using toluene diisocyanate

Polyurethanes (PUs) prepolymers blended with bentonite nanoclay and without bentonite nanoclay were prepared by the reaction of toluene-2,4-diisocyanate (TDI) and hydroxyl terminated polybutadiene (HTPB), and the chain was further extended with 1,4-butane diol (1,4-BDO) to get final polyurethane nanocomposites (PUNC). A mixture of polymer and bentonite clay enriched in montmorillonite (MMT) was formed in solution polymerization, in which MMT dispersed depending on interaction of MMT with polymer chains. The molecular structure of the monomers and the prepared PU nanocomposites was confirmed by FTIR. A series of PUNCs were prepared by varying the percent compositions of bentonite nanoclay into the PU matrix. The existence of the clay in to the PU was confirmed by scanning electron microscope (SEM). SEM images verified the good dispersion of the bentonite nanoclay in PU matrix.     

Enhanced corrosion protection coatings prepared from soluble electronically conductive polypyrrole‐clay nanocomposite materials

A series of electronically conductive nanocomposite materials that consisted of soluble polypyrrole (PPY) and layered montmorillonite (MMT) clay platelets were prepared by effectively dispersing the inorganic nanolayers of MMT clay in organic PPY matrix via an in situ oxidative polymerization with dodecylbenzene sulfonic acid (DBSA) as dopant. Organic pyrrole monomers were first intercalated into the interlayer regions of organophilic clay hosts and followed by a one‐step oxidative polymerization. The as‐synthesized electronically conductive polypyrrole–clay nanocomposite (PCN) materials were then characterized by Fourier transformation infrared (FTIR) spectroscopy, wide‐angle powder X‐ray diffraction (XRD), and transmission electron microscopy (TEM). PCNs in the form of coatings with low clay loading (e.g., 1.0 wt %) on cold‐rolled steel (CRS) were found to exhibit much better in corrosion protection over those of pristine PPY based on a series of electrochemical measurements including corrosion potential, polarization resistance, and corrosion current in 5 wt % aqueous NaCl electrolyte. Effects of the material composition on the thermal stability, optical properties, and electrical conductivity of pristine PPY along with PCN materials, in the form of fine powder, powder‐pressed pellet, and solution, were also studied by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), UV‐visible absorption spectra, and four‐point probe technique, respectively. The viscosity of PPY existed in PCN materials and pristine PPY were determined by viscometric analysis with m‐cresol as solvent. The heterogeneous nucleating effect of MMT clay platelets in PPY matrix was studied by wide‐angle powder XRD. The corresponding morphological images of the nucleating behavior of clay platelets in PPY matrix were investigated by scanning electron microscopy (SEM). © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 3264–3272, 2003     

Synthesis and characterization of polyvinyl acetate/montmorillonite nanocomposite by in situ emulsion polymerization technique

Exfoliated polyvinyl acetate/montmorillonite nanocomposite (PVAc/MMT) was prepared via in situ emulsion polymerization. The resulting PVAc with various organophilic MMT contents was investigated. In the nanocomposite latex preparation, sodium lauryl sulfate (SLS), ammonium persulfate (APS), and poly (vinyl alcohol) (PVA) are used as anionic emulsifier, conventional anionic initiator, and stabilizer, respectively. The samples were characterized using elemental analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), atomic force microscopy (AFM). The XRD and AFM results demonstrate that the MMT well dispersed at molecular level in the PVAc matrix. Thermal properties of the nanocomposite were studied by using differential scanning calorimetric analysis (DSC). The exfoliated PVAc/MMT nanocomposite showed a higher glass transition temperature and a better thermal stability compared to the pure PVAc.     

Effect of both silane‐grafted and ion‐exchanged organophilic clay in structural,thermal, and mechanical properties of unsaturated polyester nanocomposites

Unsaturated polyester (UPE) resin including styrene monomer was mixed with organophilic montmorillonite (MMT) clay and its crosslinking polymerization reaction was done in the presence of free‐radical initiator. MMT clay was modified with cetyl trimethly ammonium bromide and trimethoxy vinyl silane. The nanocomposites were characterized by X‐ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM), thermogravimetric and dynamic mechanical analyses (TGA and DMA). The exfoliated nanocomposite structure was obtained when the MMT clay was modified in the presence of both modifiers, whereas individual modifications all resulted in intercalated structures. The exfoliated UPE nanocomposite exhibited better thermal and dynamic mechanical properties when compared with pure UPE and other composites, even with 3 wt% clay loading. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Poly(vinylidene fluoride) nanofiber-based piezoelectric nanogenerators using reduced graphene oxide/polyaniline

Recently, piezoelectric nanogenerators have received great interest as they can convert waste mechanical and radiative energy to electricity and can be used in self-energy generating systems and sensor technologies. In this study, electrospun poly(vinylidene fluoride) (PVDF) nanofiber-based piezoelectric nanogenerators with reduced graphene oxide (rGO), polyaniline (PANI), and PANI-functionalized rGO (rGOPANI) have been developed. Two different types of nanofiber mats were produced: First, rGO- and rGOPANI-doped PVDF nanofiber mats and second, rGO, PANI and rGOPANI-spray-coated PVDF nanofiber mats that have worked as nanogenerators' electrodes. Then, characterizations of samples were performed in terms of piezoelectricity, Fourier transform infrared (FTIR) spectrophotometric, X-ray diffractions (XRD), and scanning electron microscopy analyses. FTIR and XRD results confirmed that piezoelectric β-crystalline phase of PVDF occurred after the electrospinning process. Besides, maximum output voltages were obtained as 7.84 and 10.60 V for rGO-doped PVDF and rGOPANI-coated PVDF nanofiber mats, respectively. As a result, the doped nanofibers were found to be more successful due to the higher device accuracy in sensor technologies compared with spray-coated samples. However, spray-coating method proved to be more suitable technique for the production of nanogenerators on an industrial scale in terms of fast and large-scale applicability. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48517.     

Fabrication and characterization of electrospun Plantago major seed mucilage/PVA nanofibers

Electrospinning is a well-known technique for producing nanofibers using synthetic and natural polymers like mucilage. In this study, Plantago major Mucilage (PMM) was blended with polyvinyl alcohol (PVA) as a nontoxic adding agent, in order to produce electrospun nanofiber. Electrospinning parameters (voltage, tip-to-collector distance, feed rate, and PMM/PVA ratio) were optimized and solution properties were analyzed. The morphology of nanofibers was investigated using scanning electron microscopy (SEM), Fourier transform infrared (FTIR), X-ray diffraction (XRD), and Brunauer–Emmett–Teller (BET). Mechanical strength of nanofibers was determined, and cell viability on nanofibers was discussed by MTT assay. The results of SEM indicated that the PMM/PVA (50/50) nanofibers obtained with average diameter of 250 nm. Viscosity, electrical conductivity, and surface tension of PMM/PVA solution were 550 Cp, 575 μS/cm, and 47.044 mN/m, respectively. FTIR and XRD results verified the exiting PMM in produced nanofibers and no chemical reaction between PMM and PVA. Improvement in mechanical strength and cell viability of nanofibers by adding PMM to PVA nanofibers indicated the potential application of PMM-based nanofibers for medical and food industries. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47852.     

聚乙烯醇/淀粉/MMT纳米复合材料的制备与性能研究

以蒙脱土（MMT）为增强填料,采用熔融加工的方法制备了聚乙烯醇（PVA）/淀粉/MMT纳米复合材料,通过X射线衍射、差示扫描量热法、扫描电子显微镜、热失重法以及力学性能测试等方法研究了MMT含量对复合材料结构与性能的影响。结果表明,在熔融加工过程中,淀粉、PVA分子破坏了MMT片层结构;MMT提高了复合材料中PVA组分结晶温度,阻碍PVA分子排入晶格,降低了复合材料熔融焓值及结晶度;MMT有效提高了材料的拉伸强度、弹性模量,同时降低了复合材料的吸水速率、平衡吸水率,提高了耐水性能。     

ITO electrode modified by self-assembling multilayer film of polyoxometallate on poly(vinyl alcohol) nanofibers and its electrocatalytic behavior

Poly(vinyl alcohol) (PVA) nanofiber mats were collected on indium tin oxide (ITO) substrate by electrospinning method. A multilayer film composed of α-[P₂W₁₈O₆₂]⁶⁻ (abbr. P₂W₁₈), a polyoxometallate (POM) anion, and poly(diallymethylammonium chloride) (abbr. PDDA) was fabricated by layer-by-layer (LBL) self-assembly technique on the PVA/ITO electrode. The PDDA/P₂W₁₈ multilayer film could be unselectively or selectively deposited on the PVA/ITO electrode via changing the amount of PVA nanofibers on the ITO substrate. The scanning electron microscope (SEM) images showed that when the electrospun time was short the PDDA/P₂W₁₈ multilayer film was unselectively deposited on PVA nanofiber mats because the amount of PVA nanofibers was too little to cover most of the ITO substrate. However, when the electrospun time was long enough, the PDDA/P₂W₁₈ multilayer film was selectively deposited on PVA nanofiber mats because of the larger surface area and higher surface energy of PVA nanofibers in comparison with the flat ITO substrate. Growth process of the multilayer film was determined by cyclic voltammetry (CV). Electrocatalytic effects of the PDDA/P₂W₁₈ multilayer film unselectively and selectively deposited on the PVA/ITO electrode on NO₂⁻ were observed.     

Enhancement of heavy metal ion adsorption using electrospun polyacrylonitrile nanofibers loaded with ZnO nanoparticles

This article describes the adsorption and tensile behavior of electrospun polyacrylonitrile (PAN) nanofiber mats loaded with different amounts of ZnO [0.5, 1.0, 2.0, and 5.0 wt%] nanoparticles. X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transforminfrared (FTIR) spectroscopy, and thermal gravimetric analysis (TGA) were utilized to characterize the resulting composite nanofibers. Microscopic investigations revealed that the increase in surface roughness and diameter of the electrospun PAN nanofibers was due to the addition of ZnO nanoparticles. Adsorption results indicated that the fabricated PAN/ZnO (2.0 wt%) composite nanofiber mats showed the best adsorption performance with 261% and 167% increase in adsorption capacities for Pb(II) and Cd(II) from aqueous solutions, respectively, compared to pristine PAN nanofibers. The adsorption equilibrium was reached within 60 min, and the process could be described using the nonlinear pseudo-second-order kinetic model. The adsorption isotherm study was better represented by the Langmuir model, which suggested a homogeneous distribution of the monolayer adsorptive sites on the surface of the composite nanofibers. Mechanical testing revealed that the decrease in tensile strength and elongation at breakof the PAN/ZnO composite nanofiber mats was due to the formation of some bead defects and agglomerates within the structure of the PAN nanofibers. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47209.