Effects of compatibilizers on the physico‐mechanical and foaming properties of polyproylene/wood‐fiber composites

Polypropylene (PP)/wood‐fiber (WF) composites were prepared by intermeshing co‐rotating twin screw extruder, and microcellular closed cell PP/WF composite foams were prepared by using pressure‐quenched batch process method. The effect of various compatibilizers on the mechanical properties, morphology, crystallinity, rheological properties, and foamability of PP/WF composites were investigated. The results showed that PP/WF composite with addition of PP‐g‐MA as compatibilizer had the highest tensile strength, stiffness, and crystallinity, after foaming, it showed highest relative density and cell density, as well as the smallest cell size. Higher crystallinity of PP/WF composites, showed higher stiffness and higher relative density. J. VINYL ADDIT. TECHNOL., 19:250–257, 2013. © 2013 Society of Plastics Engineers     

Glass fiber/wood flour modified high density polyethylene composites

Composites of high density polyethylene (HDPE) with the reinforcements of glass fiber (GF) and wood flour (WF) have been studied in this work. High‐density polyethylene‐grafted maleic hydride (HDPE‐g‐MAH) was used as a compatibilizer. In particular, the effect of GF, WF, and HDPE‐g‐MAH on the overall properties of GF/WF/HDPE composites (GWPCs in short form) was systematically studied. The results indicate that HDPE‐g‐MAH as a compatibilizer can effectively promote the interfacial adhesion between GF/WF and HDPE. By the incorporations of GF/WF, the heat deflection temperature can reach above 120°C, and the water absorption can be below 0.7%, also the tensile strength, flexural strength, and impact strength of GWPCs can surpass 55.2 Mpa, 69.4 Mpa, and 11.1 KJ/m², respectively. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Rice husk/poly(propylene‐co‐ethylene) composites: Effect of different coupling agents on mechanical,thermal, and morphological properties

Poly(propylene‐co‐ethylene) composites with rice husk were prepared in a corotating intermeshing twin‐screw extruder using four different coupling agents. While modified maleic anhydrides such as maleated polypropylene (MAPP) and maleated polyethylene (MAPE) are commonly used as compatibilizers to improve interfacial adhesion between lignocellulosic filler and matrix, in this study, polypropylene grafted with acid comonomer (CAPP) and high‐density polyethylene grafted with acid comonomer (CAPE) were also used. The morphologies and the thermal and mechanical properties of the composites were characterized using scanning electron microscopy, thermogravimetric analysis, differential scanning analysis, tensile and impact tests. The results indicate that the base resin of the compatibilizer is an important factor in determining the effectiveness of compatibilizers for composites. Composites with PP‐based compatibilizers are more effective than PE‐based compatibilizers due to the improved wetting of the former compatibilizer in the matrix polymer. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of sawdust surface treatment and compatibilizer addition on mechanical behavior,morphology, and moisture uptake of polypropylene/sawdust composites

Polypropylene/sawdust composites were investigated to assess the effect of sawdust surface treatment and compatibilizer addition on polymer/fiber adhesion. Two silane coupling agents were used for sawdust surface treatment: vinyl‐tris (2‐methoxyethoxy) silane and (3‐aminopropyl)triethoxysilane. Maleic anhydride grafted polypropylene was used as compatibilizer. Composites were prepared in a corotating twin‐screw extruder coupled to a Haake torque rheometer and submitted to tensile and bending tests as well as scanning electron microscopy (SEM). Moisture uptake tests were also performed. Results showed that incorporation of untreated sawdust to polypropylene (PP) caused reduction in composite tensile strength and increase in stiffness. When the only treatment used was surface modification with silane coupling agents, no significant changes were observed in mechanical properties. However, when compatibilizer was added to the composites, tensile strength was increased, and % elongation at break reduced, indicating improved system compatibility. The composite presenting the highest increase in tensile strength was that containing sawdust treated with amino silane in addition to the compatibilizer. SEM analyses corroborated the mechanical property results. POLYM. ENG. SCI., 2010. © 2009 Society of Plastics Engineers     

聚乳酸基木塑复合材料的相容性研究

以聚乳酸(PLA)、松木粉为主要原料,用双螺杆挤出机制备了PLA基木塑复合材料。研究了硅烷偶联剂和增容剂对PLA基木塑复合材料力学性能和结构形态的影响。结果表明,硅烷偶联剂可以增加PLA与木粉之间的界面结合力,但是对体系的力学性能影响不是很大;增容剂的加入能够提高复合材料的力学性能。     

Preparation of HDPE/SEBS‐g‐MAH and its effect on mechanical properties of HDPE/wood flour composites

In this article, high density polyethylene/styrene‐ethylene‐butylene‐styrene block copolymer blends (HDPE/SEBS) grafted by maleic anhydride (HDPE/SEBS‐g‐MAH), which is an effective compatibilizer for HDPE/wood flour composites was prepared by means of torque rheometer with different contents of maleic anhydride (MAH). The experimental results indicated that MAH indeed grafted on HDPE/SEBS by FTIR analysis and the torque increased with increasing the content of maleic anhydride and dicumyl peroxide (DCP). Styrene may increase the graft reaction rate of MAH and HDPE/SEBS. When HDPE/SEBS MAH was added to HDPE/wood flour composites, tensile strength and flexural strength of composites can reach 25.9 and 34.8 MPa in comparison of 16.5 and 23.8 MPa (without HDPE/SEBS‐g‐MAH), increasing by 157 and 146%, respectively. Due to incorporation of thermoplastic elastomer in HDPE/SEBS‐g‐MAH, the Notched Izod impact strength reached 5.08 kJ m^?2, increasing by 145% in comparison of system without compatibilizer. That HDPE/SEBS‐g‐MAH improved the compatibility was also conformed by dynamic mechanical measurement. Scanning electron micrographs provided evidence for strong adhesion between wood flour and HDPE matrix with addition of HDPE/SEBS‐g‐MAH. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Morphological,mechanical, and physical properties of composites made with wood flour‐reinforced polypropylene/recycled poly(ethylene terephthalate) blends

Wood flour (WF)‐filled composites based on a polypropylene (PP)/recycled polyethylene terephthalate (r‐PET) matrix were prepared using two‐step extrusion. Maleic anhydride grafted polypropylene (MAPP) was added to improve the compatibility between polymer matrices and WF. The effects of filler and MAPP compatibilization on the water absorption, mechanical properties, and morphological features of PP/r‐PET/WF composites were investigated. The addition of MAPP significantly improved mechanical properties such as tensile strength, flexural strength, tensile modulus, and flexural modulus compared with uncompatibilized composites, but decreased elongation at break. Scanning electron microscopic images of fracture surface specimens revealed better interfacial interaction between WF and polymer matrix for MAPP‐compatibilized PP/r‐PET/WF composites. MAPP‐compatibilized PP/r‐PET/WF composites also showed reduced water absorption due to improved interfacial bonding, which limited the amount of absorbable water molecules. These results indicated that MAPP acts as an effective compatibilizer in PP/r‐PET/WF composites. POLYM. COMPOS., 38:1749–1755, 2017. © 2015 Society of Plastics Engineers     

Mechanical properties of wood flake–polyethylene composites. II. Interface modification

This article discusses the methods of interface modification of composites based on raw wood flakes and high‐density polyethylene (HDPE) and the effects of these modifications on composite properties. An HDPE matrix was modified by a reaction with maleic anhydride (MA) in a twin‐screw extruder and then compounded with wood flakes to produce wood–polyethylene composites. Wood flakes were modified by a reaction with a silane coupling agent in an aqueous medium before being compounded with HDPE to produce silane‐modified WPCs. Differential scanning calorimetry and Fourier transform infrared spectroscopy data provide evidence for the existence of a polyethylene (PE)–silane‐grafted wood structure, which acts as a compatibilizer for wood flakes and PE. The results of MA‐modified composites indicate that some maleated HDPE is reacting with wood through esterification to form a compatibilizer for wood flakes and HDPE. Significant improvements in tensile strength, ductility, and Izod impact strength were obtained. Scanning electron micrographs provide evidence for strong interactions between the wood flakes and the matrix agent. The results indicate that 1–2 wt % MA modification on HDPE and 1–3 wt % silane treatment on wood flakes provide WPCs with the optimum properties. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2505–2521, 2002     

Effect of interfacial interaction on the crystallization and mechanical properties of PP/nano‐CaCO3 composites modified by compatibilizers

To investigate the effect of interfacial interaction on the crystallization and mechanical properties of polypropylene (PP)/nano‐CaCO₃ composites, three kinds of compatibilizers [PP grafted with maleic anhydride (PP‐g‐MA), ethylene–octene copolymer grafted with MA (POE‐g‐MA), and ethylene–vinyl acetate copolymer grafted with MA (EVA‐g‐MA)] with the same polar groups (MA) but different backbones were used as compatibilizers to obtain various interfacial interactions among nano‐CaCO₃, compatibilizer, and PP. The results indicated that compatibilizers encapsulated nano‐CaCO₃ particles, forming a core–shell structure, and two interfaces were obtained in the compatibilized composites: interface between PP and compatibilizer and interface between compatibilizer and nano‐CaCO₃ particles. The crystallization and mechanical properties of PP/nano‐CaCO₃ composites were dependent on the interfacial interactions of these two interfaces, especially the interfacial interaction between PP and compatibilizer. The good compatibility between PP chain in PP‐g‐MA and PP matrix improved the dispersion of nano‐CaCO₃ particles, favored the nucleation effect of nano‐CaCO₃, increased the tensile strength and modulus, but reduced the ductility and impact strength of composites. The partial compatibility between POE in POE‐g‐MA and PP matrix had little effect on crystallization and mechanical properties of PP/nano‐CaCO₃ composites. The poor compatibility between EVA in EVA‐g‐MA and PP matrix retarded the nucleation effect of nano‐CaCO₃, and reduced the tensile strength, modulus, and impact strength. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Resistance of paper mill sludge/wood fiber/high‐density polyethylene composites to water immersion and thermotreatment

The disposal of paper mill sludge (PMS) is a difficult environmental problem. Thus, PMS has been used as a substitute for wood fiber (WF) to reinforce high‐density polyethylene (HDPE). In this study, we compared PMS–WF–HDPE composites with composites without PMS after water immersion and thermal treatment. Water immersion and thermal treatment were conducted at 25 and 70°C, respectively. The results show that the composites with PMS absorbed less water but lost more of their original flexural properties after immersion; thereby, their strength was compromised. These reduced mechanical properties could be partially restored after redrying. After the thermotreatment, the composites with added PMS lost their weight and flexural properties, whereas the composites without PMS gained flexural strength. The results show that the thermotreatment improved the impact strength of the composites when no more than one‐third of WF was replaced with PMS. Fourier transform infrared spectroscopy and energy‐dispersive X‐ray energy‐dispersive spectroscopy showed that the wood index of the PMS composite decreased more than the index of the non‐PMS composite, whereas the carbonyl index increased more. However, the PMS composite showed a lower increase in the total oxygen/carbon weight ratio. This study suggested that limited amounts of WF could be substituted with PMS to reinforce HDPE. However, WF–PMS–HDPE composites should not be used in hot, humid environments for long periods. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41655.     

Mechanical properties of teak wood flour‐reinforced HDPE composites

Mechanical properties such as tensile and impact strength behavior of teak wood flour (TWF)‐filled high‐density polyethylene (HDPE) composites were evaluated at 0–0.32 volume fraction (Φ_f) of TWF. Tensile modulus and strength initially increased up to Φ_f = 0.09, whereas a decrease is observed with further increase in the Φ_f. Elongation‐at‐break and Izod impact strength decreased significantly with increase in the Φ_f. The crystallinity of HDPE also decreased with increase in the TWF concentration. The initial increase in the tensile modulus and strength was attributed to the mechanical restraint, whereas decrease in the tensile properties at Φ_f > 0.09 was due to the predominant effect of decrease in the crystallinity of HDPE. The mechanical restraint decreased the elongation and Izod impact strength. In the presence of coupling agent, maleic anhydride‐grafted HDPE (HDPE‐g‐MAH), the tensile modulus and strength enhanced significantly because of enhanced interphase adhesion. However, the elongation and Izod impact strength decreased because of enhanced mechanical restraint on account of increased phase interactions. Scanning electron microscopy showed a degree of better dispersion of TWF particles because of enhanced phase adhesion in the presence of HDPE‐g‐MAH. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Thermoplastic elastomers based on epoxidized natural rubber and high‐density polyethylene blends: Effect of blend compatibilizers on the mechanical and morphological properties

Epoxidized natural rubber (ENR) with a level of epoxide groups of 20 mol % was prepared via the performic epoxidation method. It was then used to blend with high‐density polyethylene (HDPE) at various blend ratios. Three types of blend compatibilizers were prepared. These included a graft copolymer of HDPE and maleic anhydride (MA; i.e., HDPE‐g‐MA) and two types of phenolic modified HDPEs using phenolic resins SP‐1045 and HRJ‐10518 (i.e., PhSP‐PE and PhHRJ‐PE), respectively. We found that the blend with compatibilizer exhibited superior tensile strength, hardness, and set properties to that of the blend without compatibilizer. The ENR and HDPE interaction via the link of compatibilizer molecules was the polar functional groups of the compatibilizer with the oxirane groups in the ENR molecules. Also, another end of the compatibilizer molecules (i.e., HDPE segments) was compatibilizing with the HDPE molecules in the blend components. The blend with compatibilizer also showed smaller phase morphology than the blend without compatibilizer. Among the three types of the blend compatibilizer, HDPE‐g‐MA provided the blend with the greatest strength and hardness properties but the lowest set properties. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of coupling agents on rice‐husk‐filled HDPE extruded profiles

Lignocellulosic composites are diversifying their applications into various fields as they can meet the requirements of the respective applications by changing the matrix, fiber resource and processing ingredients. In this research work we explored the potential of extruded rice‐husk‐filled high density polyethylene (HDPE) composite profiles for structural applications. The structure and the properties of the interface in fiber‐reinforced composites play a crucial role in determining the performance properties of the composites. An optimum degree of adhesion between the fiber and the matrix is required for efficient stress transfer from the matrix to the fiber. Generally, coupling agents are used to improve the adhesion between lignocellulosic filler and the polymer matrix in structural composite materials. In this study, four different coupling agents based on ethylene‐(acrylic ester)‐(maleic anhydride) terpolymers and ethylene‐(acrylic ester)‐(glycidyl methacrylate) terpolymers were used to enhance the performance properties of the composites. The results indicated that these coupling agents enhanced the tensile and flexural strength of the composites significantly, and the extent of the coupling effect depends on the nature of the interface formed. Incorporation of coupling agents enhanced the resistance to thermal deformation and the water absorption properties of the composite, whereas it reduced the extrusion rate significantly. Among the four coupling agents used, EGMA1—the one with a glycidyl methacrylate functional group and without any methyl acrylate pendant group on the polymer backbone—was found to be the best coupling agent for the rice‐husk‐filled HDPE composites. Copyright © 2004 Society of Chemical Industry     

Effects of filler–filler and polymer–filler interactions on rheological and mechanical properties of HDPE–wood composites

High‐density polyethylene (HDPE)–wood composite samples were prepared using a twin‐screw extruder. Improved filler–filler interaction was achieved by increasing the wood content, whereas improved polymer–filler interaction was obtained by adding the compatibilizer and increasing the melt index of HDPE, respectively. Then, effects of filler–filler and polymer–filler interactions on dynamic rheological and mechanical properties of the composites were investigated. The results demonstrated that enhanced filler–filler interaction induced the agglomeration of wood particles, which increased the storage modulus and complex viscosity of composites and decreased their tensile strength, elongation at break, and notched impact strength because of the stress concentration. Stronger polymer–filler interaction resulted in higher storage modulus and complex viscosity and increased the tensile and impact strengths due to good stress transfer. The main reasons for the results were analyzed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Rice straw fiber reinforced high density polyethylene composite: Effect of coupled compatibilizating and toughening treatment

In this study, rice‐straw (RS) filled high density polyethylene (HDPE) composites were manufactured by extrusion and injection molding. Three compatibilizers, which are unfunctionalized ethylene/propylene copolymer (uEPR), maleic anhydride grafted EPR (EPR‐g‐MA) and PE‐g‐MA, and their combinations were introduced to strengthen fiber‐matrix interphase. The mechanical and morphological properties of composites were investigated. For single‐compatibilizer system, PE‐g‐MA or EPR‐g‐MA alone enhanced tensile, flexural, and impact strengths of resultant composites compared with HDPE/RS system without compatibilizers. Different toughening origins of individual compatibilizer were discussed based on composites' interphase morphologies and mechanical properties. For combined‐compatibilizers system, the PE‐g‐MA/EPR weight ratio is important for several properties of composites. The optimum ratio was considered as 2 : 1 and 1 : 1 for PE‐g‐MA/uEPR and PE‐g‐MA/EPR‐g‐MA modified composites, respectively. Also, composites modified by combined PE‐g‐MA/EPR‐g‐MA showed better impact strength than that modified by PE‐g‐MA alone. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Development and characterization of green composites from bio‐based polyethylene and peanut shell

In the present work, different compatibilizers, namely polyethylene‐graft‐maleic anhydride (PE‐g‐MA), polypropylene‐graft‐maleic anhydride (PP‐g‐MA), and polystyrene‐block‐poly(ethylene‐ran‐butylene)‐block‐polystyrene‐graft‐maleic anhydride (SEBS‐g‐MA) were used on green composites derived from biobased polyethylene and peanut shell (PNS) flour to improve particle–polymer interaction. Composites of high‐density polyethylene/peanut shell powder (HDPE/PNS) with 10 wt % PNS flour were compatibilized with 3 wt % of the abovementioned compatibilizers. As per the results, PP‐g‐MA copolymer lead to best optimized properties as evidenced by mechanical characterization. In addition, best particle–matrix interface interactions with PP‐g‐MA were observed by scanning electron microscopy (SEM). Subsequently HDPE/PNS composites with varying PNS flour content in the 5–30 wt % range with PP‐g‐MA compatibilizer were obtained by melt extrusion and compounding followed by injection molding and were characterized by mechanical, thermal, and morphological techniques. The results showed that PNS powder, leads to an increase in mechanical resistant properties (mainly, flexural modulus, and strength) while a decrease in mechanical ductile properties, that is, elongation at break and impact absorbed energy is observed with increasing PNS flour content. Furthermore, PNS flour provides an increase in thermal stability due to the natural antioxidant properties of PNS. In particular, composites containing 30 wt % PNS powder present a flexural strength 24% and a flexural modulus 72% higher than the unfilled polyethylene and the thermo‐oxidative onset degradation temperature is increased from 232 °C up to 254 °C thus indicating a marked thermal stabilization effect. Resultant composites can show a great deal of potential as base materials for wood plastic composites. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43940.     

Effectiveness of functionalized polyolefins as compatibilizers for polyethylene/wood flour composites

The effects of various types of compatibilizers on the mechanical properties of high‐density polyethylene/wood flour (HDPE/WF) composite were investigated. Functionalized polyolefins such as maleated and acrylic acid grafted polyethylenes, maleated polypropylene (PPgMA) and styrene‐ethylene/butylene‐styrene triblock copolymer (SEBSgMA) were incorporated to reduce the interfacial tension between the polyethylene matrix and the wood filler. Among them, it was found that maleated linear low‐density polyethylene (LLDPEgMA) gave maximum tensile and impact strength of the composites, presumably because of better compatibility with the HDPE matrix. Similar but less enhanced improvements in the mechanical properties, depending on the compatibilizer loading, were seen for the SEBSgMA system. Whereas acrylic acid grafted high‐density polyethylene (HDPEgAA) and maleated polypropylene (PPgMA) only slightly improved tensile modulus and tensile strength; and they both increased with increasing loadings of compatibilizers. A scanning electron microscopic study was employed to reveal the interfacial region and confirm these findings. In addition, dynamical mechanical thermal measurements also revealed the interaction between filler and matrix, and FTIR spectroscopy was used to assign the chemical fixation and the various chemical species involved at the surface of the wood fillers before and after surface treatment.     

Effect of fiber pretreatment condition on the interfacial strength and mechanical properties of wood fiber/PP composites

The effect of fiber surface pretreatment on the interfacial strength and mechanical properties of wood fiber/polypropylene (WF/PP) composites are investigated. The results demonstrate that fiber surface conditions significantly influence the fiber–matrix interfacial bond, which, in turn, determines the mechanical properties of the composites. The WF/PP composite containing fibers pretreated with an acid–silane aqueous solution exhibits the highest tensile properties among the materials studied. This observation is a direct result of the strong interfacial bond caused by the acid/water condition used in the fiber pretreatment. Evidence from coupling chemistry, rheological and electron microscopic studies support the above conclusion. When SEBS‐g‐MA copolymer is used, a synergistic toughening effect between the wood fiber and the copolymer is observed. The V‐notch Charpy impact strength of the WF/PP/SEBS‐g‐MA composite is substantially higher than that of the WF/PP composite. The synergistic toughening mechanisms are discussed with respect to the interfacial bond strength, fiber‐matrix debonding, and matrix plastic deformation. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1000–1010, 2000     

Synergistic enhancement of glass fiber and tetrapod‐shaped ZnO whisker on the mechanical and thermal behavior of isotactic polypropylene

Improvement of mechanical and thermal properties is always the goal of high‐performance general plastic for engineering applications. Herein, isotactic polypropylene/glass fiber/tetrapod‐shaped zinc oxide (iPP/GF/T‐ZnOw) composites are developed via melt‐extrusion on twin‐screw extruder. To improve the distribution of T‐ZnOw in iPP matrix, T‐ZnOw is first modified by various silane coupling agents and its structure is characterized by scanning electron microscopy, Fourier transform infrared spectra, and X‐ray diffraction (XRD). The optimized treatment condition is determined via comparison of activation index. The introduction of GF and T‐ZnOw could improve the mechanical properties including tensile strength, elastic modulus, flexural strength, flexural modulus, and impact strength, indicating that the surface modification and compatibilizer could enhance the interfacial interaction of iPP/GF/T‐ZnOw composites. Moreover, XRD and differential scanning calorimentryresults show that T‐ZnOw as a novel β‐nucleating agent could induce the formation of β‐crystal and the existence of GF counteracts the formation of β‐crystal induced by T‐ZnOw. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44217.     

High‐density polyethylene nanocomposites using masterbatches of chlorinated polyethylene/graphene oxide

Graphene‐based nanocomposites were generated by solution mixing of the graphene oxide filler with chlorinated polyethylene compatibilizers followed by melt mixing of the solution mixed masterbatches with high‐density polyethylene. Compatibilizers with two different chlorination contents were used in different amounts in order to analyze their effect on the morphology and properties of resulting nanocomposites. Peak melting point as well as overall crystallinity was affected by graphene oxide as well as compatibilizers. Compatibilizer with higher chlorination content also interacted with polar graphene oxide surface more effectively thus leading to better filler dispersion in the composites. The addition of compatibilizers to the composites resulted in their shear and processing stability at higher angular frequencies and temperature, which otherwise was not possible for pure polymer as well as composites without compatibilizer. The mechanical performance of the nanocomposites at ambient conditions was also affected by the factors like filler delamination, plasticization of the matrix, compatibilizer content as well as their chlorination level and amorphous/semicrystalline nature. An increase of 16% in tensile modulus and 21% in strength of the composites with 5 wt% of 25% chlorinated compatibilizer at 0.5 wt% graphene oxide content was observed. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers