A Comparative Study of Polystyrene/Layered Silicate Nanocomposites,Synthesized by Emulsion and Bulk Polymerization Methods

Polystyrene/clay (PS/clay) nanocomposites were synthesized by insitu emulsion and bulk polymerization methods. Sodium montmorillonite (Na-MMT) and two organically modified clays (Cloisite 30B and Cloisite 15A) were employed. The effect of clay swelling method and sonication on the d-spacing of silicate layers was also investigated. The surface morphology of pure PS and PS/clay nanocomposites were comparatively investigated using scanning electron microscopy (SEM). Thermogravimetric analysis (TGA) of PS and PS/clay nanocomposites revealed the improved thermal stability of PS/clay nanocomposites compared to pure PS. Results of optical transparency tests showed the better transparency of nanocomposite films compared to the pure PS film.     

Deformation and fracture behavior of polyamide nanocomposites: The effect of clay dispersion

This study describes the effect of the clay content and its dispersion on deformation and fracture behavior of polyamide nanocomposites. Two nanocomposite systems, intercalated and exfoliated nanocomposites containing layered silicate, were compared. They were prepared by melt‐compounding of polyamide with sodium montmorillonite or organophilized montmorillonite. It has been shown that while the exfoliated structure imparts to the nanocomposite higher stiffness and strength, the toughness is inferior to the intercalated nanocomposite. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of the clay size on the dispersion morphology and emulsion stability of ABS/layered silicate nanocomposites

ABS/layered silicate nanocomposites were synthesized through an emulsion polymerization with different sizes of silicates. The particle sizes of Laponite, Cloisite‐Na and Kunipia‐F are about 20–30, 70–150, and 300–500 nm, respectively. When ABS was synthesized by the emulsion polymerization in the presence of Laponite and Cloisite‐Na, ABS/layered silicate nanocomposite emulsion showed a stable suspension without the precipitation of solid particle. On the other hand, ABS/layered silicate nanocomposite synthesized with Kunipia‐F showed the precipitation of large aggregated particles and the phase separation. Smaller sizes of silicates like Laponite and Cloisite‐Na than polymerized particle worked as resided barrier preventing the emulsion particle from coagulation. Larger size of silicate like Kunipia‐F than emulsion particle was not able to enclose the emulsion particle delicately because of its stiffness and large aspect ratio. The monomers inserted into the intercalated Kunipia‐F connected the ABS particles and clay particles. The Kunipia‐F particles anchored ABS particles around them inducing the aggregation and precipitation of ABS particles. ABS copolymer emulsion and aqueous silicate dispersion were mixed to compare with synthesized ABS/layered silicate nanocomposites and showed a stable suspension. With small amount of Laponite or Cloisite‐Na, nanocomposite emulsion of Kunipia‐F was also stabilized. Laponite and Cloisite‐Na worked as a steric stabilizer. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Single-ion conducting polymer-silicate nanocomposite electrolytes for lithium battery applications

Solid-state polymer-silicate nanocomposite electrolytes based on an amorphous polymer poly[(oxyethylene)₈ methacrylate], POEM, and lithium montmorillonite clay were fabricated and characterized to investigate the feasibility of their use as ‘salt-free’ electrolytes in lithium polymer batteries. X-ray scattering and transmission electron microscopy studies indicate the formation of an intercalated morphology in the nanocomposites due to favorable interactions between the polymer matrix and the clay. The morphology of the nanocomposite is intricately linked to the amount of silicate in the system. At low clay contents, dynamic rheological testing verifies that silicate incorporation enhances the mechanical properties of POEM, while impedance spectroscopy shows an improvement in electrical properties. With clay content ≥15 wt.%, mechanical properties are further improved but the formation of an apparent superlattice structure correlates with a loss in the electrical properties of the nanocomposite. The use of suitably modified clays in nanocomposites with high clay contents eliminates this superstructure formation, yielding materials with enhanced performance.     

Nanocomposite materials based on isosorbide methacrylate/Cloisite 20A

This paper reports experiments on grafting of a new polymerizable monomer onto organophilic montmorillonite. The monomer, 5‐methacryloyloxy‐1,4:36‐D ‐anhydrosorbitol (MAS), was synthesized by reacting methacryloyl chloride and isosorbide in the presence of Et₃N as base. Then, Cloisite 20A was reacted with vinyltrichlorosilane to replace the edge hydroxyl groups of the clay with a vinyl moiety. Because the reaction liberates HCl, it was performed in the presence of sodium hydrogen carbonate to prevent the exchange of quaternary alkylammonium cations with H⁺ ions. Only the silanol groups on the edge of the clay react with vinyltrichlorosilane. After the reaction, the product maintained the same basal spacing as the precursor. The radical polymerization of the product with MAS as a vinyl monomer led to chemical grafting of the polymer onto the montmorillonite surface. The homopolymer formed during polymerization was separated from the grafted organoclay by Soxhlet extraction. Chemical grafting of the polymer onto Cloisite 20A was confirmed using infrared spectroscopy. The prepared nanocomposite materials and the grafted nanoparticles were studied using X‐ray diffraction and scanning and transmission electron microscopy. Exfoliated nanocomposite was obtained for 1 wt% clay loadings. The nanocomposites were studied using thermogravimetric and dynamic mechanical analyses. Improved thermal properties were observed for nanocomposites with 1–5 wt% clay content. © 2012 Society of Chemical Industry     

Dispersion characteristics and rheology of organoclay nanocomposites based on a segmented main-chain liquid-crystalline polymer having side-chain azopyridine with flexible spacer

The dispersion characteristics and rheology of organoclay nanocomposites based on a main-chain liquid-crystalline polymer having side-chain azopyridine with flexible spacer (PABP) were investigated using X-ray diffraction (XRD), transmission electron microscopy (TEM), and oscillatory shear rheometry. In the preparation of nanocomposites via solution blending under vigorous stirring, two commercial organoclays (Southern Clay Products) were employed: one (Cloisite 30B) treated with a surfactant (MT2EtOH) having hydroxyl groups, and the other (Cloisite 20A) treated with a nonpolar surfactant (2M2HT) having hydrogenated tallow. Also prepared, for comparison, were nanocomposites prepared by mixing PABP with natural clay (montmorillonite, MMT). The following observations were made. (i) PABP/Cloisite 30B nanocomposite has featureless XRD patterns and a very high degree of dispersion of Cloisite 30B aggregates as determined from TEM. (ii) PABP/Cloisite 20A nanocomposite has shown a conspicuous XRD reflection peak and intercalation of Cloisite 20A aggregates as determined from TEM. (iii) PABP/MMT nanocomposite has shown XRD patterns, which are virtually the same as the XRD patterns of neat PABP with a slightly increased gallery distance, and it has very poor dispersion of MMT aggregates in the matrix of PABP. The observed high degree of dispersion of Cloisite 30B aggregates in PABP/Cloisite 30B nanocomposite is attributable to the formation of hydrogen bonds between the pyridyl group of side-chain azopyridine and the hydroxyl groups in the surfactant MT2EtOH residing at the surface of Cloisite 30B. The presence of hydrogen bonds in the PABP/Cloisite 30B nanocomposite was confirmed by in situ Fourier transform infrared (FTIR) spectroscopy. It was observed via polarized optical microscopy that the liquid crystallinity of PABP in the PABP/Cloisite 30B nanocomposites was more or less intact with a very high degree of dispersion of Cloisite 30B aggregates. Oscillatory shear flow measurements of the organoclay nanocomposites prepared support the conclusions drawn from XRD, TEM, and FTIR spectroscopy.     

Polymer–montmorillonite nanocomposites: Chemical grafting of polyvinyl acetate onto Cloisite 20A

This paper is an account of the experiments on grafting polyvinyl acetate onto organophilic montmorillonite. Cloisite 20A was reacted with vinyltrichlorosilane to replace the edge hydroxyl groups of the clay with a vinyl moiety. Because the reaction liberates HCl, it was performed in the presence of sodium hydrogencarbonate to prevent the exchange of quaternary alkylammonium cations with H⁺ ions. Only the silanol groups on the edge of the clay react with vinyltrichlorosilane. After the reaction, the product maintained the same basal spacing as the precursor. The radical polymerization of the product with vinyl acetate as a vinyl monomer leads to chemical grafting of polyvinyl acetate onto montmorillonite surface. The homopolymer formed during polymerization was separated from the grafted organoclay by Soxhelt extraction. Chemical grafting of the polymer onto Cloisite 20A was confirmed by infrared spectroscopy. The prepared nanocomposite materials and the grafted nano‐particles were studied by XRD, SEM, and TEM. Exfoliated nanocomposite was obtained for 0.5% clay content. Nanocomposites with 1% and 3% clay contents showed significant intercalation and agglomeration occurred at higher clay loadings. The nanocomposites were studied by thermogravimertic analysis (TGA) and dynamic mechanical analysis (DMTA). Improved thermo‐mechanical properties were observed for nanocomposite with 0.5% clay content. POLYM. COMPOS., © 2011 Society of Plastics Engineers.     

Effect of Clay Types on the Mechanical,Dynamic Mechanical and Morphological Properties of Polypropylene Nanocomposites

In the present investigation Polypropylene–Maleic anhydride grafted polypropylene–organically modified MMT (PP-MAPP-OMMT) nanocomposites were prepared by melt mixing in a twin screw extruder followed by injection molding. The effect of clay chemistry and compatibilizer on the properties of the nanocomposites has been studied. Sodium montmorillonite has been organically modified using quaternary and alkyl amine intercalants. A comparative account with commercial quaternary ammonium modified clays i.e Cloisite 20A, Cloisite 15A and Cloisite 30B has been presented. Storage modulus of PP matrix also increased in the nanocomposites, indicating an increase in the stiffness of the matrix polymer with the addition of organically modified nanoclays. The morphology of the nanocomposites has been examined using wide angle X-ray diffraction (WAXD) and transmission electron microscopy (TEM). Morphological findings revealed efficient dispersion of organically modified nanoclays within the PP matrix. MAPP compatibilized PP/Cloisite 15A nanocomposites displayed finely dispersed exfoliated nanomorphology as compared with other systems.     

Diffusion behavior of water and sulfuric acid in epoxy/organoclay nanocomposites

The research on polymer‐layered silicate nanocomposites is currently an expanding field of study because they often exhibit a wide range of improved properties over their unmodified starting polymers. Epoxy/organoclay nanocomposites have been prepared by intercalating epoxy into the organoclay montmorillonite. The intercalation and/or exfoliation of the clay within the nanocomposite were monitored using X‐ray diffraction and transmission electron microscopy. Diffusion was studied through epoxy samples containing up to 10 phr of organically treated montmorillonite following the gravity method. The water and sulfuric acid diffusion within the epoxy‐based nanocomposites were evaluated in terms of diffusivity, weight change and penetration depth of the sulfuric acid element S as function of immersion time and immersion temperature. An investigation of the resistance of epoxy nanocomposite to a corrosive environment by immersion into sulfuric acid at elevated temperature was performed. The effect of the degree of exfoliation of the clay on moisture barrier effect and corrosion resistance is specifically studied. The data has been compared to those obtained from the neat epoxy resin to evaluate the diffusion properties of the nanocomposites. It was found that the diffusion of water and that of acid do not obey Fick's law, and that the higher the organoclay content the higher weight change was obtained. The presence of the organoclay enhanced the diffusivity and delayed the penetration of the sulfuric acid. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Chlorosulfonated polypropylene: preparation and its application as a coupling agent in polypropylene-clay nanocomposites

Polypropylene nanocomposites containing organophilic layered silicate were prepared by melt mixing. In order to increase polypropylene polarity, Cl and SO₂Cl groups were introduced by reaction with sulfuryl chloride under UV irradiation. Chlorosulfonated polypropylene was subsequently melt-compounded with organophilized montmorillonite clay to produce a masterbatch. The masterbatch was then blended with commercial isotactic polypropylene. An organophilized silicate (Cloisite 15A) and three chlorosulfonated polypropylenes with different degrees of functionalization were used in this study. The effect of various processing procedures was examined as well. The morphology of nanocomposites obtained was examined using TEM and X-ray diffraction. It has been shown that the presence of polar groups leads to an increased gallery distance and partial exfoliation. Nevertheless, full exfoliation of clay platelets has not been achieved. The observed morphologies affected the resulting tensile mechanical behaviour: both stiffness and strength significantly increased.     

Synthesis and characterization of epoxy based nanocomposites

Epoxy‐clay nanocomposites were synthesized to examine the effects of the content and type of different clays on the structure and mechanical properties of the nanocomposites. Diglycidyl ether of bisphenol‐A (epoxy) was reinforced by 0.5–11 wt % natural (Cloisite Na⁺) and organically modified (Cloisite 30B) types of montmorillonite. SEM results showed that as the clay content increased, larger agglomerates of clay were present. Nanocomposites with Cloisite 30B exhibited better dispersion and a lower degree of agglomeration than nanocomposites with Cloisite Na⁺. X‐ray results indicated that in nanocomposites with 3 wt % Cloisite 30B, d‐spacing expanded from 18.4 Å (the initial value of the pure clay) to 38.2 Å. The glass transition temperature increased from 73°C, in the unfilled epoxy resin, to 83.5°C in the nanocomposite with 9 wt % Cloisite 30B. The tensile strength exhibited a maximum at 1 wt % modified clay loading. Addition of 0.5 wt % organically modified clay improved the impact strength of the epoxy resin by 137%; in contrast, addition of 0.5 wt % unmodified clay improved the impact strength by 72%. Tensile modulus increased with increasing clay loading in both types of nanocomposites. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1081–1086, 2005     

Preparation and characterization of poly(butylene terephthalate) nanocomposites with various organoclays

Layered‐silicate‐based polymer–clay nanocomposite materials were prepared depending on the surface modification of montmorillonite (MMT). Nanocomposites consisting of poly(butylene terephthalate) (PBT) as a matrix and dispersed inorganic clay modified with cetyl pyridinium chloride (CPC), benzyl dimethyl N‐hexadecyl ammonium chloride, and hexadecyl trimethyl ammonium bromide by direct melt intercalation were studied. The organoclay loading was varied from 1 to 5 wt %. The organoclays were characterized with X‐ray diffraction (XRD) to compute the crystallographic spacing and with thermogravimetric analysis to study the thermal stability. Detailed investigations of the mechanical and thermal properties as well as a dispersion study by XRD of the PBT/clay nanocomposites were conducted. X‐ray scattering showed that the layers of organoclay were intercalated with intercalating agents. According to the results of a differential scanning calorimetry analysis, clay acted as a nucleating agent, affecting the crystallization. The PBT nanocomposites containing clay treated with CPC showed good mechanical properties because of intercalation into the polymer matrix. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Formation of polymer nanocomposites with various organoclays

The role of the type of organic modifier used with montmorillonite (MMT) on the formation of polymer/clay nanocomposites in the melt compounding process was investigated. Various organoclays including primary [12‐aminolauric acid (12ALA)], secondary [dioctylamine (DOA)], tertiary [trioctylamine (TOA)], and two commercial quaternary (Cloisite 30B and 20A) MMTs were melt compounded with carefully selected polymers including polypropylene, polystyrene, styrene–acrylonitrile copolymer, poly(methyl methacrylate), poly(vinylidene fluoride), and acrylonitrile–butadiene copolymer (NBR). X‐ray diffraction and transmission electron microscopy characterizations confirmed that the two quaternary ammonium organoclay (Cloisite 30B and 20A) have superior compatibility compared to the primary (12ALA), secondary (DOA), and tertiary (TOA) ammonium organoclay. DOA and TOA can form polymer/clay nanocomposites only with the most polar polymer (NBR). Cloisite Na⁺ and 12ALA can not form nanocomposite with any polymers. The large organic surface area of the quaternary ammonium organoclay could be the reason of the best compatibility with polar polymers. It is estimated that long alkyl ammonium chains of organic modifier can spread over the clay surface more effectively than short alkyl chains. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1888–1896, 2005     

Crystalline forms in melt‐crystallized syndiotactic polystyrene/clay nanocomposites

X‐ray diffraction methods and polarized optical microscopy have been used to investigate the structural change of syndiotactic polystyrene/clay nanocomposites. The nanocomposite has prepared by mixing an sPS polymer solution with organically modified montmorillonite. Both X‐ray diffraction and transmission electron microscopy results indicate that most of the swellable silicate layers are exfoliated and randomly dispersed into the sPS matrix. The X‐ray diffraction data also show the presence of polymorphism in sPS/clay nanocomposites, which is strongly dependent on the thermal history of the nanocomposites from the melt and on the content of clay. In this study, the effect of premelting temperatures and crystallization temperatures of sPS and sPS/clay nanocomposites on their crystalline phases is discussed.     

Properties of Waterborne Polyurethane/Clay Nanocomposite Adhesives

A series of waterborne polyurethane (WBPU)/clay nanocomposite dispersions using two different organically modified clays, namely Cloisite 15A and Cloisite 30B, were prepared. It was found that the properties of WBPU/clay nanocomposites were highly dependent on both the clay content and the clay surface characteristic (hydrophilic/hydrophobic). A WBPU/clay nanocomposite dispersion with a higher clay content showed a less negative zeta potential. A lower zeta potential for dispersion with Cloisite 30B compared to Cloisite 15A was observed indicating a higher stability of the dispersion. The tensile strength, Young's modulus and adhesive strength of WBPU/clay nanocomposite containing Cloisite 30B were also higher than those of nanocomposite containing Cloisite 15A. The optimum clay contents, with respect to these properties, for nanocomposites with Cloisite 15A and Cloisite 30B were found to be 2 wt% and 3 wt%, respectively.     

In‐situ polymerization of polyamide 66 nanocomposites utilizing interfacial polycondensation,Part 1: Organoclay nanocomposites

Effective dispersion of organically modified montmorillonite‐layered silicates in nylon 66 is addressed by synthesizing nanocomposites in situ via interfacial polycondensation from a suspension of silicate platelets in one of the monomer phases using either a stirred or unstirred reactor, while avoiding the detrimental heat history associated with melt compounding of this high melting polymer system. The effects of mixing methodology, reaction conditions, concentration ratio, and clay content are evaluated to elucidate process mechanisms and produce high molecular weight product. Enhanced stiffness of the nanocomposites measured by tensile modulus is related to their nanoscale morphology as characterized by transmission electron microscopy and wide angle X‐ray diffraction. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Effects of silane grafting on the morphology and thermal stability of poly(ethylene terephthalate)/clay nanocomposites

An alkylammonium intercalated montmorillonite (A‐MMT) was modified by edge grafting with 3‐glycidoxypropyltrimethoxysilane. In comparison with poly(ethylene terephthalate) (PET)/A‐MMT, the resultant grafted clay, S‐A‐MMT, exhibited improved miscibility with PET matrix and revealed better dispersion state in the melting compounded PET/S‐A‐MMT nanocomposites. As a result, the PET/S‐A‐MMT nanocomposite had slower degradation rate owing to the enhanced clay barrier effect. Meanwhile, the nanocomposite exhibited lower degradation onset temperature under nitrogen because of the clay catalysis effect, which can be explained by the decreasing degradation reaction energy calculated from Coats–Redfern method of degradation kinetics. In the other hand, nanocomposite with better clay dispersion state exhibited increasing thermal oxidative stability due to clay barrier effect of hindering oxygen to diffuse in, which accorded with the continuous and compact char surface formed during polymer degradation. The clay catalysis and barrier effect of silicate layers were presented directly in isothermal oxidative TGA experiment. Furthermore, the mechanical and crystallization properties of PET/clay nanocomposites were investigated as well. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Effect of hydrogen bonding on the rheology of polycarbonate/organoclay nanocomposites

The linear dynamic viscoelastic properties and non-linear transient rheology of polycarbonate (PC)/clay nanocomposites were investigated at temperatures ranging from 240 to 280 °C. For the study, nanocomposites of PC and natural montmorillonite (Cloisite Na⁺) or chemically modified clay (Cloisite 30B) were prepared by melt blending in a twin-screw extruder. Cloisite 30B is a natural montmorillonite modified with methyl, tallow, bis-2-hydroxyethyl, quaternary ammonium chloride (MT2EtOH). In both PC/Cloisite Na⁺ and PC/Cloisite 30B nanocomposites the concentration of clay was varied from 2.3 to 4.3 wt%. In situ Fourier transform infrared (FTIR) spectroscopy results show that at temperatures ranging from 30 to 280 °C the carbonyl groups in PC and the hydroxyl groups in MT2EtOH of Cloisite 30B in PC/Cloisite 30B nanocomposites formed hydrogen bonds, while no evidence of hydrogen bonding was observed in the PC/Cloisite Na⁺ nanocomposites. There are no discernible sharp reflections in the X-ray diffraction (XRD) patterns of PC/Cloisite 30B nanocomposites, after Cloisite 30B having the d₀₀₁ spacing of 1.85 nm was mixed with PC, whereas the d₀₀₁ spacing changes little (1.17 nm) before and after the mixing of Cloisite Na⁺ to PC. Transmission electron microcopy (TEM) images show that organoclay platelets are well dispersed in PC/Cloisite 30B nanocomposites, while the untreated clay platelets are poorly dispersed in PC/Cloisite Na⁺ nanocomposites. The observed differences in XRD patterns and TEM images between the two nanocomposite systems are explained by in situ FTIR spectroscopy. The results of rheological measurements (linear dynamic viscoelasticity, non-linear transient shear flow, and steady-state shear flow) support the conclusions drawn from the results of XRD, TEM, and FTIR spectroscopy.     

Young's modulus of effective clay clusters in polymer nanocomposites

In polymer nanocomposites, the interfacial region plays a key role in the reinforcement of materials properties. Traditional two-phase micromechanical models usually ignore the contribution of such interfacial region to the overall materials properties. In this study, we use molecular dynamics simulation to determine the effective size and the Young's modulus of effective clay clusters which are regarded as basic building blocks in clay-based polymer nanocomposites. Two types of clay clusters are considered: one is fully exfoliated clay and another is partially exfoliated clay. The calculated Young's modulus of effective clay clusters can be used to predict the overall mechanical properties of clay-based polymer nanocomposites.     

Dispersion of nanoclays with poly(ethylene terephthalate) by melt blending and solid state polymerization

Melt intercalation of clay with poly(ethylene terephthalate; PET) was investigated in terms of PET chain mobilities, natures of clay modifiers, their affinities with PET, and nanocomposite solid state polymerization (SSP). Twin screw extrusion was used to melt blend PET resins with intrinsic viscosities of 0.48, 0.63, and 0.74 dL/g with organically modified Cloisite 10A, 15A, and 30B montmorillonite clays. Clay addition caused significant molecular weight reductions in the extruded PET nanocomposites. Rates of SSP decreased and crystallization rates increased in the presence of clay particles. Cloisite 15A blends showed no basal spacing changes, whereas the basal spacings of Cloisite 10A and Cloisite 30B nanocomposites increased after melt extrusion, indicating the presence of intercalated nanostructures. After SSP these nanocomposites also exhibited new lower angle X‐ray diffraction peaks, indicating further expansion of their basal spacings. Greatest changes were seen for nanocomposites prepared from the lowest molecular weight PET and Cloisite 30B, indicating its greater affinity with PET and that shorter more mobile PET chains were better able to enter its galleries and increase basal spacing. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013