Toughening effects of ethylene–vinyl acetate copolymers with different vinyl acetate content and viscosity on nylon 1010 blends

Nylon 1010 blends with ethylene–vinyl acetate copolymer (EVA) and maleated ethylene–vinyl acetate (EVA‐g‐MAH) were prepared through melt blending. The vinyl acetate (VA) content and viscosity of EVA significantly affected the notched impact strength of nylon/EVA/EVA‐g‐MAH (80/15/5) blends. The nylon/EVA/EVA‐g‐MAH blends with high notched impact strength (over 60 kJ/m²) were obtained when the VA content in EVA ranged from 28 to 60 wt%. The effect of VA content on the notched impact strength of blends was related to the glass transition temperature for EVA with high VA content and crystallinity for EVA with low VA content. For nylon blends with EVA with the same VA content, low viscosity of EVA led to high notched impact strength. Fracture morphology of nylon/EVA/EVA‐g‐MAH (80/15/5) blends showed that blends with ductile fracture behavior usually had large matrix plastic deformation, which was the main energy dissipation mechanism. A relationship between the notched impact strength and the morphology of nylon/EVA/EVA‐g‐MAH (80/15/5) blends was well correlated by the interparticle distance model. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Modification of low‐density polyethylene by graft copolymerization with maleic anhydride and blends with polyamide 6

Modification of low‐density polyethylene (LDPE) hyperbranched grafting with a maleic anhydride (MAH) was carried out using corotating twin screw extruder in the presence of benzoyl peroxide. The LDPE/polyamide 6 (PA6) and LDPE‐g‐MAH/PA6 blends were obtained with a corotating twin screw extruder. The melt viscosity of the grafted LDPE was measured by a capillary rheometer. The grafted copolymer was characterized by Fourier transform infrared spectroscopy and scanning electron microscopy The effects of variations in temperature, PA6 loading, and benzoyl peroxide and MAH concentration were investigated. The results show that most MAH monomers were grafted onto the LDPE at a lower MAH concentration. With the proper selection of the reaction parameters, we obtained a grafting degree higher than 4.9%. Mechanical test results indicate that the blends had good interfacial adhesion and good stability of the phase structure during heating, which was reflected in the mechanical properties. Furthermore, the results reveal that the tensile strength of the blends increased continuously with increasing PA6 content. Moreover, the home‐synthesized maleated LDPE could be used for the compatibilization of LDPE/PA 6 blends. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

The effect of matrix composition on the properties of cellulosic fibers–polyethylene composites

The solution/precipitation method was used for the preparation of polyethylene (PE)/cellulosic fibers composites. Blends of modified linear low density PE [linear low density PE‐grafted maleic anhydride (LLDPE‐g‐MAH)] with low density PE (LDPE) were used as matrices for the aforementioned composites. Blends of LDPE with a copolymer of LDPE and acrylic acid (AA)/n‐butyl acrylate (n‐BA) [(AA/n‐BA)–LDPE] were also studied for the same purpose. The reinforcing effect of cellulosic fibers in terms of tensile strength is more enhanced when mixtures of the modified polar polymer with pure PE were used as matrices, as compared with that corresponding to matrices consisting of modified PE alone. Regarding the Izod impact strength, composites of LLDPE‐g‐MAH presented the best performance with an improvement of 135% in comparison with specimens consisting of LDPE matrix, whereas composites of (AA/n‐BA)‐LDPE matrix showed a modest improvement of their impact resistance. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis of polyethylene‐graft‐poly(styrene‐co‐maleic anhydride) and its compatibilizing effects on polyethylene/starch blends

Low density polyethylene (LDPE) was reacted with benzoyl peroxide (BPO) and 2,2,6,6‐tetramethyl‐l‐piperidinyloxy (TEMPO) to prepare a latent macroinitiator, PE–TEMPO. Little polymer was synthesized when maleic anhydride (MAH) was bulk polymerized in the presence of the PE–TEMPO. However, addition of styrene accelerated the polymerization rate and PE‐grafted‐poly(styrene‐co‐maleic anhyride) [PE‐g‐P(ST‐co‐MAH)] was produced to a high yield. Chemical reaction between MAH units and hydroxyl groups of starch was nearly undetectable in the PE/PE‐g‐P(ST‐co‐MAH)/starch blend system, and the tensile properties of the blend were not enhanced significantly. However, addition of tetrabutyl titanate (TNBT) during the blending procedure improved the tensile properties significantly through an increased interfacial adhesion between the components in the blend system. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2434–2438, 2003     

Thermally stable low‐density polyethylene/polyhydroxybutyrate pairs: Synergy between organomodified nanoclay and LDPE‐g‐MAH

Nanocomposites of low‐density polyethylene/polyhydroxybutyrate (LDPE/PHB) containing organomodified montmorillonite (OMMT) and/or LDPE grafted maleic anhydride (LDPE‐g‐MAH) were prepared with a wide range of composition ratios using a vertical co‐rotating twin‐screw microCompounder. To infer the effect of OMMT and LDPE‐g‐MAH on the thermal stability of prepared nanocomposites, all samples were characterized by thermogravimetric analysis while changing clay and compatibilizer contents. Accordingly, two commonly used kinetic models (Coats–Redfern and Horowitz–Metzger) were employed to correlate the thermal stability of the samples with kinetic parameters, including activation energy and pre‐exponential factor. Furthermore, morphological features of LDPE/PHB in the presence or absence of OMMT and LDPE‐g‐MAH were studied using scanning electron microscopy, transmission electron microscopy, and wide‐angle X‐ray diffraction analysis. It was found that for a specific OMMT composition ratio (1 wt %), the thermal stability is enhanced due to an exfoliated structure. However, for samples containing more organoclay (>=3 wt %), the thermal stability was reduced showing the competition between the barrier effect of organoclay platelets and the catalyzing effect of ammonium salts. Moreover, when using LDPE‐g‐MAH as compatibilizer, it acted as a good coupling agent in all compositions in LDPE major phase systems in contrast to PHB major phase samples. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45922.     

Effect of the compatibility on dielectric performance and breakdown strength of poly(vinylidene fluoride)/low‐density polyethylene blends

Immiscible polymer blends with high dielectric constant (ε) and improved breakdown strength (E_b) performance were obtained by composing poly(vinylidene fluoride) (PVDF) with low‐density polyethylene (LDPE) or the LDPE grafted with maleic anhydride (LDPE‐g‐MAH) through melt‐blending way. The dielectric properties of these blends were emphasized for considering the compatibility effect on the energy storage application. Interface morphology, co‐continuity behavior, and grafted ratio were simultaneously investigated to detect the compatibility enhancement after introducing MAH. Results showed that the MAH positively improved the dielectric properties. Both the measured E_b of PVDF/LDPE and PVDF/LDPE‐g‐MAH blends showed a minimum value at v^PVDF = 50 vol % because of the worst compatibility; meanwhile, higher E_b of PVDF/LDPE‐g‐MAH than that of PVDF/LDPE blend was observed owing to the better compatibility. For considering the effect interface morphology on the dielectric performance, layer‐structure films composing with pure PVDF and LDPE layers were further constructed and studied. It was revealed that the layered structure could be treated as a helpful way to improve ε and E_b for immiscible polymer blends. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42507.     

High‐frequency welding of thermoplastic LLDPE/PA 6/PE‐g‐MAH ternary blends

High frequency (HF) welding of linear low density polyethylene (LLDPE) melt blends with polyamide 6 (PA6) was done at 27.12 MHz using maleic anhydride grafted polyethylene (PE‐g‐MAH) as compatibilizer. HF welding was not possible for the blends at room temperature, but possible at higher temperatures (50, 80°C) although the maximum relaxation frequency was lower than the operating frequency. Greater dielectric constant, dissipation factor, and welding performance were obtained when PA 6 was premixed with PE‐g‐MAH rather than the one‐shot process where all the components were mixed simultaneously. This was interpreted in terms of lowered viscosity of PA 6 phase, which encapsulates the flow effectively and provides great skin effect. Also, the peeling force of resin–resin was greater than resin–nylon mesh due to the higher melting temperature and vacancy of nylon mesh. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synergetic toughness and morphology of poly(propylene)/nylon 11/maleated ethylene‐propylene diene copolymer blends

Polypropylene (PP)/nylon 11/maleated ethylene‐propylene‐diene rubber (EPDM‐g‐MAH) ternary polymer blends were prepared via melt blending in a corotating twin‐screw extruder. The effect of nylon 11 and EPDM‐g‐MAH on the phase morphology and mechanical properties was investigated. Scanning electron microscopy observation revealed that there was apparent phase separation for PP/EPDM‐g‐MAH binary blends at the level of 10 wt % maleated elastomer. For the PP/nylon 11/EPDM‐g‐MAH ternary blends, the dispersed phase morphology of the maleated elastomer was hardly affected by the addition of nylon 11, whereas the reduced dispersed phase domains of nylon 11 were observed with the increasing maleated elastomer loading. Furthermore, a core‐shell structure, in which nylon 11 as a rigid core was surrounded by a soft EPDM‐g‐MAH shell, was formed in the case of 10 wt % nylon 11 and higher EPDM‐g‐MAH concentration. In general, the results of mechanical property measurement showed that the ternary blends exhibited inferior tensile strength in comparison with the PP matrix, but superior toughness. Especially low‐temperature impact strength was obtained. The toughening mechanism was discussed with reference to the phase morphology. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Biodegradation of blends of polyethylene‐octene elastomer with starches by fungi

Five fungi including Aspergillus niger, Penicilium pinophilum, Chaetoomium globsum, Gliocladium virens and Aureobasium pullulans were used to investigate the biodegradation of starch‐based elastomers: polyethylene‐octene elastomer (POE)/starch and grafted POE‐g‐MAH/starch copolymer blends. The viability of the composite spore suspensions were measured before estimating the fungal growth on the surface of specimens. The weight loss, morphology and mechanical properties of the blended specimens were measured using scanning electron microscopy and a mechanical properties tester after 28 days of culturing. The spore suspension in the experiment showed good viability. Pure POE and POE‐g‐MAH did not allow significant fungal growth. Pure POE did not lose weight or have a change in tensile strength, but pure POE‐g‐MAH lost about 0.07% of its weight with a slight reduction in tensile strength during culture period. There was heavy growth on the surface of POE/starch and POE‐g‐MAH/starch blends after 28 days of culturing. The weight loss of POE/starch and POE‐g‐MAH/starch blends increased with increasing starch content. POE‐g‐MAH/starch blends tended to lose more weight than POE/starch blends. After biodegradation, the surface of POE/starch and POE‐g‐MAH/starch blends became rough with many holes and cracks, indicating that the films were eroded by the fungi. Tensile strength of POE/starch and POE‐g‐MAH/starch blends decreased after culturing because of microbial attack. On the contrary, elongation at break of POE‐g‐MAH/starch blends increased after biodegradation. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci 114:3574–3584, 2009     

N2‐filled hollow glass beads as novel gas carriers for microcellular polyethylene

N₂‐filled hollow glass beads (HGB) were first used as novel gas carriers to prepare microcellular polymers by compression molding. Dicumyl peroxide was acted as crosslink agent to control the produced microcellular structure of low density polyethylene (LDPE)/HGB. The effect of temperature, pressure and the content of gel on the embryo‐foaming, and final‐foaming structure are investigated. Scanning electronic microscopy shows that the average cell size of microcellular LDPE ranges from 0.1 to 10 μm, and the foam density is about 10⁹–10¹¹ cells/cm³. A clear correlation is established between preserving desirable micromorphologies of microcellular LDPE in different processing stage and tuning processing factors. The pertinent foaming mechanism of microcellular materials foamed with HGB is proposed. Because of the good mechanical strength, low density, weak water‐absorption, and excellent heat insulate ability, microcellular LDPE has great potential application in energy building materials. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Influence of in situ compatibilization on in situ formation of low‐density polyethylene/polyamide 6 blends by reactive extrusion

Low‐density polyethylene/polyamide 6 (LDPE/PA6) blends were in situ formed by reactive extrusion, in which in situ polymerization of ε‐caprolactam (CL) and in situ copolymerization of maleic anhydride grafted low‐density polyethylene (LDPE‐MA) and CL took place simultaneously. The latter reaction could be considered as in situ compatibilization, and the influence of in situ compatibilization on the morphologies, thermal properties, and rheological behaviors of the blends was investigated in this work. Scanning electron microscopy showed that the in situ compatibilization could dramatically reduce the dispersed phase sizes and narrow the size distribution. The thermal properties indicated that in differential scanning calorimetry (DSC) cooling scans, fractionated crystallization of the PA6 component was observed in all cases and was promoted with increasing the amount of LDPE‐MA. The DSC second heating scans showed the in situ compatibilization could stimulate the formation of the less stable γ‐crystalline form of PA6 in the blends. Dynamic rheological experiments revealed the in situ compatibilization had enhanced the viscosity, storage modulus, and loss modulus of the blend and reduce the corresponding slope values of the storage modulus and loss modulus. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Mechanical properties of teak wood flour‐reinforced HDPE composites

Mechanical properties such as tensile and impact strength behavior of teak wood flour (TWF)‐filled high‐density polyethylene (HDPE) composites were evaluated at 0–0.32 volume fraction (Φ_f) of TWF. Tensile modulus and strength initially increased up to Φ_f = 0.09, whereas a decrease is observed with further increase in the Φ_f. Elongation‐at‐break and Izod impact strength decreased significantly with increase in the Φ_f. The crystallinity of HDPE also decreased with increase in the TWF concentration. The initial increase in the tensile modulus and strength was attributed to the mechanical restraint, whereas decrease in the tensile properties at Φ_f > 0.09 was due to the predominant effect of decrease in the crystallinity of HDPE. The mechanical restraint decreased the elongation and Izod impact strength. In the presence of coupling agent, maleic anhydride‐grafted HDPE (HDPE‐g‐MAH), the tensile modulus and strength enhanced significantly because of enhanced interphase adhesion. However, the elongation and Izod impact strength decreased because of enhanced mechanical restraint on account of increased phase interactions. Scanning electron microscopy showed a degree of better dispersion of TWF particles because of enhanced phase adhesion in the presence of HDPE‐g‐MAH. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of a N,N′‐disubstituted phenylenediamine stabilizer and SB/EPDM compatibilizer on toughness and morphology of blends of pre‐aged polyethylene with high‐impact polystyrene

The effect of a N,N′‐disubstituted 1,4‐phenylenediamine stabilizer and styrene‐butadiene block copolymer (SB)/ethylene‐propylene elastomer (EPDM) compatibilizer on mechanical properties and phase structure of pre‐aged low‐density polyethylene (LDPE; a model of aged recyclate)/high‐impact polystyrene (HIPS) blends was studied. A strong cooperative effect between the stabilizer and compatibilizer on the impact strength and fineness of the phase structure of LDPE/HIPS blends was found. Analysis of chemical reactions assumed to proceed in the system during processing led to the conclusion that improvement in the impact strength and phase structure was accounted for by reactive formation of a LDPE‐SB graft copolymer in a process supported by the presence of the bifunctional amine‐based stabilizer. The mixture of the amine stabilizer with SB/EPDM is a very promising upgrading system for post‐consumer plastic waste containing pre‐oxidized LDPE. J. VINYL. ADDIT. TECHNOL. 12:58–65, 2006. © 2006 Society of Plastics Engineers.     

Properties of different chitosan/low‐density polyethylene antibacterial plastics

A series of low‐density polyethylene (LDPE) antibacterial functional plastics were prepared by mechanical blending with commercial chitosan (CS), self‐made water‐soluble chitosan (W‐CS), and microchitosan as antibacterial agents. The effects of the antibacterial agent content on the elongation at break of the obtained plastics were tested, and the bacteriostatic effects against Escherichia coli, Bacillus subtilis, and Proteus species were investigated. The results indicate that the elongation at break of LDPE with antibacterial agent decreased and had a slower decline when the mass ratio of CS to LDPE was greater than 0.5 : 100. The LDPE‐based plastics showed different antibacterial activities against the three experimental strains, and plastics with W‐CS exhibited the best antibacterial activity against B. subtilis. However, the antibacterial content had little effect on the antibacterial ratio. Moreover, 6‐week soil burial tests indicated that the addition of CS caused a decrease in the resistance of LDPE to microbiological deterioration in a natural environment. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation of HDPE/SEBS‐g‐MAH and its effect on mechanical properties of HDPE/wood flour composites

In this article, high density polyethylene/styrene‐ethylene‐butylene‐styrene block copolymer blends (HDPE/SEBS) grafted by maleic anhydride (HDPE/SEBS‐g‐MAH), which is an effective compatibilizer for HDPE/wood flour composites was prepared by means of torque rheometer with different contents of maleic anhydride (MAH). The experimental results indicated that MAH indeed grafted on HDPE/SEBS by FTIR analysis and the torque increased with increasing the content of maleic anhydride and dicumyl peroxide (DCP). Styrene may increase the graft reaction rate of MAH and HDPE/SEBS. When HDPE/SEBS MAH was added to HDPE/wood flour composites, tensile strength and flexural strength of composites can reach 25.9 and 34.8 MPa in comparison of 16.5 and 23.8 MPa (without HDPE/SEBS‐g‐MAH), increasing by 157 and 146%, respectively. Due to incorporation of thermoplastic elastomer in HDPE/SEBS‐g‐MAH, the Notched Izod impact strength reached 5.08 kJ m^?2, increasing by 145% in comparison of system without compatibilizer. That HDPE/SEBS‐g‐MAH improved the compatibility was also conformed by dynamic mechanical measurement. Scanning electron micrographs provided evidence for strong adhesion between wood flour and HDPE matrix with addition of HDPE/SEBS‐g‐MAH. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Correlation between compounding sequence and the properties of glass fiber‐Reinforced nylon‐6,6 composite

The effects of the compounding sequence and addition of maleic anhydride grafted polypropylene (PP‐g‐MAH) as a sizing agent on the properties of glass fiber (GF)/nylon‐6,6 composite were investigated. Mechanical properties of tensile, impact, and flexural strength were measured. The fractured surface was analyzed to compare the variation of interfacial characteristics by different compounding sequences and addition of a sizing agent. It was found that mechanical and rheological properties of a composite are strongly affected by the compounding sequence and the addition of a sizing agent. In general, the addition of PP‐g‐MAH results in lowering the mechanical properties compared to GF/nylon‐6,6, while proper compounding sequence results in improved mechanical properties. Lowering melt viscosity of composites is achieved by addition of sizing agent and varied depending on the compounding sequence. POLYM. ENG. SCI., 59:155–161, 2019. © 2018 Society of Plastics Engineers     

Toughening and phase separation behavior of nylon 6–PEG block copolymers and in situ nylon 6–PEG blend via in situ anionic polymerization

We have prepared in situ molded products of morphologically different nylon 6/polyethylene glycol (PEG) copolymers and their blends via anionic polymerization of ε-caprolactam in the presence of several kinds of PEG derivatives using sodium caprolactamate as a catalyst and carbamoyl caprolactam derivative as an initiator. Three carbamoyl caprolactams, such as tolylene dicarbamoyl dicaprolactam (TDC), hexamethylene dicarbamoyl dicaprolactam (HDC), and cyclohexyl carbamoyl caprolactam (CCC), with different functionalities and activities were used. Phase separation behavior was investigated by dynamic mechanical thermal analysis (DMTA) and DSC during in situ polymerization and melt crystallization. The mechanical properties of these molded products were evaluated. PEG segments in the block copolymers showed amorphous characteristics, whereas a large fraction of unreacted PEG segments was crystallized in as-polymerized samples, except for the products obtained using the CCC activator. The presence of PEG derivatives retarded the crystallization of nylon 6 part during in situ polymerization as well as melt crystallization. However, PEG segments did not alter the crystalline structure of nylon 6, showing α-crystalline modification. The nylon 6–PEG–nylon 6 triblock copolymers showed the highest impact strength, whereas the nylon 6–PEG diblock copolymers and in situ nylon 6–PEG blends showed no improved toughness. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 1285–1303, 1999     

High‐flow nylon 6 by in situ polymerization: Synthesis and characterization

A new synthetic strategy for high‐flow nylon 6 was developed in this article. Generation 1, 2, 3 (G1, G2, G3) polyamidoamine (PAMAM) dendrimers reacted with p‐phthalic acid by equimolar terminal groups in water solution, respectively, and mother salt solution was then prepared. The high‐flow nylon 6 was prepared with suitable quantity of mother salt solution, end‐capping agent, and ?‐caprolactam by in situ polymerization. Blue shifts are found for the peaks of NH (γN? H and 2δN? H) of the high‐flow nylon 6 compared with pure nylon 6 in the IR spectra. Comparing with the pure nylon 6, the high‐flow nylon 6 containing low content of PAMAM units, has high‐flow property and almost the same mechanical property. The high‐flow nylon 6 with low content of PAMAM units has greater melt‐flow index (MFI) (the value of MFI increased by 70–90%). Hardly any decrease in the tensile strength is observed with the elongation at break decreasing by 20–35%. But the izod impact strength of the high‐flow nylon 6 increases. The SEM images show that the high‐flow nylon 6 presents brittle fracture with conglomeration‐like structure, while pure nylon 6 exhibits plastic fracture with island‐like structure. DSC thermograms of nonisothermal crystallization exhibit that the peak of high‐flow nylon 6 broadens compared with pure nylon 6, and the broader peak means the wider processing temperature. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Properties of uncompatibilized and compatibilized poly(butylene terephthalate)–LLDPE blends

In this work, blends of poly(butylene terephthalate) (PBT) and linear low‐density polyethylene (LLDPE) were prepared. LLDPE was used as an impact modifier. Since the system was found to be incompatible, compatibilization was sought for by the addition of the following two types of functionalized polyethylene: ethylene vinylacetate copolymer (EVA) and maleic anhydride‐grafted EVA copolymer (EVA‐g‐MAH). The effects of the compatibilizers on the rheological and mechanical properties of the blends have been also quantitatively investigated. The impact strength of the PBT–LLDPE binary blends slightly increased at a lower concentration of LLDPE but increased remarkably above a concentration of 60 wt % of LLDPE. The morphology of the blends showed that the LLDPE particles had dispersed in the PBT matrix below 40 wt % of LLDPE, while, at 60 wt % of LLDPE, a co‐continuous morphology was obtained, which could explain the increase of the impact strength of the blend. Generally, the mechanical strength was decreased by adding LLDPE to PBT. Addition of EVA or EVA‐g‐MAH as a compatibilizer to PBT–LLDPE (70/30) blend considerably improved the impact strength of the blend without significantly sacrificing the tensile and the flexural strength. More improvement in those mechanical properties was observed in the case of the EVA‐g‐MAH system than for the EVA system. A larger viscosity increase was also observed in the case of the EVA‐g‐MAH than EVA. This may be due to interaction of the EVA‐g‐MAH with PBT. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 989–997, 1999     

Studies on LDPE—Cyanoethylated lignocellulosics blends using epoxy functionalized LDPE as compatibilizer

Rubberwood flour and cellulose have been plasticized by cyanoethylation and then blended with low‐density polyethylene (LDPE). A small quantity of epoxy functionalized polyethylene i.e., polyethylene‐co‐glycidyl methacrylate (PEGMA) has been added to further enhance the mechanical properties. The mechanical properties were measured according to the standard ASTM methods. SEM analysis was performed for both fractured and unfractured blend specimens. The mechanical properties were improved by the addition of PEGMA compatibilizer. LDPE blends with cyanoethylated wood flour (CYWF) showed higher tensile strength and modulus than cyanoethylated cellulose CYC‐LDPE blends. However CYC‐LDPE blends exhibited higher relative elongation at break values as compared with the former. The TGA analysis showed lowering of thermal stability as the filler content is increased and degradation temperature of LDPE is shifted slightly to lower temperature. DSC analysis showed loss of crystallinity for the LDPE phase as the filler content is increased for both types of blends. Dielectric properties of the blends were similar to LDPE, but were lowered on adding PEGMA. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 219–237, 2006