Friction and wear properties of polyimide matrix composites reinforced with short basalt fibers

Short basalt fiber (BF) reinforced polyimide (PI) composites were fabricated by means of compression‐molding technique. The friction and wear properties of the resulting composites sliding against GCr15 steel were investigated on a model ring‐on‐block test rig under dry sliding conditions. The morphologies of the worn surfaces and the transfer films that formed on the counterpart steel rings were analyzed by means of scanning electron microscopy. The influence of the short BF content, load, and sliding speed on the tribological behavior of the PI composites was examined. Experimental results revealed that the low incorporation of BFs could improve the tribological behavior of the PI composites remarkably. The friction coefficient and wear rate decreased with increases in the sliding speed and load, respectively. The transfer film that formed on the counterpart surface during the friction process made contributions to reducing the friction coefficient and wear rate of the BF‐reinforced PI composites. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Friction and wear behavior of basalt‐fabric‐reinforced/solid‐lubricant‐filled phenolic composites

To improve the tribological properties of basalt‐fabric‐reinforced phenolic composites, solid lubricants of MoS₂ and graphite were incorporated, and the tribological properties of the resulting basalt‐fabric composites were investigated on a model ring‐on‐block test rig under dry sliding conditions. The effects of the filler content, load, and sliding time on the tribological behavior of the basalt‐fabric composites were systematically examined. The morphologies of the worn surfaces and transfer films formed on the counterpart steel rings were analyzed by means of scanning electron microscopy. The experimental results reveal that the incorporation of MoS₂ significantly decreased the friction coefficient, whereas the inclusion of graphite improved the wear resistance remarkably. The results also indicate that the filled basalt‐fabric composites seemed to be more suitable for friction materials serving under higher loads. The transfer films formed on the counterpart surfaces during the friction process made contributions to the reduction of the friction coefficient and wear rate of the basalt‐fabric composites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

The effect of carbon fiber content on the friction and wear properties of carbon fiber reinforced polyimide composites

The current study examines the tribological performance of polyimide and carbon fiber reinforced polyimide (CF/PI) under dry sliding condition. Different contents of carbon fibers were employed as reinforcement. All filled and unfilled polyimide composites were tested against CGr15 ball and representative testing was performed. The effects of carbon fiber content on tribological properties of the composites were investigated. The worn surface morphologies of neat PI and its composites were examined by scanning electron microscopy and the wear mechanisms were discussed. Moreover, all filled polyimides have superior tribological characteristics to unfilled polyimides. The optimum wear reduction was obtained when the content of carbon fiber is 20 vol %. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Mechanical and tribological properties of polyoxymethylene modified with nanoparticles and solid lubricants

Polyoxymethylene (POM) composites modified with nanoparticles, polytetrafluoroethylene (PTFE) and MoS₂ were prepared by a twin‐screw extruder. The effect of nanoparticles and solid lubricant PTFE/MoS₂ on mechanical and tribological properties of the composites were studied. Tribological tests were conducted on an Amsler friction and wear tester using a block‐on‐ring arrangement under dry sliding and oil lubricated conditions, respectively. The results showed that generally speaking POM nanocomposites had better stiffness and tribological properties than corresponding POM composites attributed to the high surface energy of nanoparticles, except that the tensile strength of three composites and dry‐sliding tribological properties of POM/3%Al₂O₃ nanocomposite decreased due to the agglomeration of nanoparticles. Tribological properties differed under dry sliding and oil lubricated conditions. The friction coefficient and wear volume of POM nanocomposites under oil lubricated condition decreased significantly. The increased deformation resistance supported the increased wear resistance of POM nanocomposites. POM/PTFE/MoS₂/3%Al₂O₃ nanocomposite had the best mechanical and tribological properties of all three composites, which was attributed to the synergistic effect of nanoparticles and PTFE/MoS₂. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Comparative study on the tribological properties of the polyimide composites reinforced with different fibers

In this study, friction and wear of polyimides reinforced by carbon, glass, aramid, and nano‐alumina fibers were studied and comparatively evaluated against Si₃N₄ on a ball‐on‐disk test rig under dry rotating and reciprocating sliding, and coefficient of friction and wear rate were considered as responses. The worn surfaces of the composites were examined by scanning electron microscopy to reveal wear mechanisms of the materials' damage. Wear mechanisms are found to be dependent on the test conditions and mechanical properties of the composites itself. It was proven that different reinforcements had different effects on the friction and wear behavior of the polyimide composites to a great extent. The testing condition also had an important role on the tribological properties of the same materials. The best performance was shown by glass fiber‐reinforced polyimide composites owing to their excellent strength and hardness which can share the applied load on the sliding surface. POLYM. COMPOS., 37:2541–2548, 2016. © 2015 Society of Plastics Engineers     

Effect of several solid lubricants on the mechanical and tribological properties of phenolic resin‐based composites

The flake graphite, polytetrafluoroethylene, and molybdenum disulfide (MoS₂) filled phenolic resin‐based composites were prepared by hot press molding. The thermal, mechanical, and tribological properties of composites were studied systematically. The morphologies of the worn surfaces and the change of chemical compositions during the sliding process of the composites were analyzed by scanning electron microscopy and X‐ray photoelectron spectroscopy, respectively. It was found that the heat‐resisting performance and the hardness of the composites are less affected by solid lubricants, while the solid lubricants did harm to the flexural strength of the composites. The friction and wear behaviors of composites highly depended on the volume fractions of solid lubricants and the sliding conditions. The wear resistance increases and the coefficient of friction decreases when the filler load increases. In addition, the appropriate content of solid lubricants is beneficial to reducing the sensitivities of the composites to load and sliding speed. POLYM. COMPOS., 36:2203–2211, 2015. © 2014 Society of Plastics Engineers     

Influence of solid lubricant reinforcement on wear behavior of Kevlar fabric composites

The friction and wear behavior of Kevlar fabric composites reinforced by PTFE or graphite powders was investigated using a Xuanwu‐III friction and wear tester at dry sliding condition, with the unfilled Kevlar fabric composite as a reference. The worn surfaces were analyzed by means of scanning electron microscope, and X‐ray photoelectron spectroscopy. It was found that PTFE or graphite as fillers could significantly improve the tribological behavior of the Kevlar fabric composites, and the Kevlar fabric composites filled with 20% PTFE exhibited the best antiwear and antifriction ability among all evaluated cases. The transfer films established with two lubricants in sliding wear of composites against metallic counterparts made contributions to reducing friction coefficient and wear rate of Kevlar fabric composites. In particular, FeF₂ generated in the sliding of Kevlar fabric composites filled with PTFE against counterpart pin improved the bonding strength between the transfer film and counterpart surface, which accounted for the lowest friction coefficient and wear rate of the Kevlar fabric composites filled with PTFE measured in the testing. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008.     

Effects of lubricating‐oil additives on the friction and wear properties of polymers and their composites sliding against steel under oil‐lubricated conditions

The effects of lubricating‐oil additive zinc dialkyldithiophosphate (ZDDP) on the friction and wear properties of polymers and their composites sliding against GCr15 bearing steel were studied by using an MHK‐500 ring‐on‐block wear tester (Timken wear tester). Then the frictional surfaces of the friction pairs were examined by using electron probe microanalysis (EPMA). Experimental results show that the ZDDP contained in liquid paraffin has little effect on the friction coefficients of the polyimide (PI) or polyamide 66 (PA66) against GCr15 bearing steel friction pairs compared with that under the lubrication of liquid paraffin, but it slightly reduces the friction coefficients of polytetrafluoroethylene (PTFE) or its composites against GCr15 bearing steel friction pairs. Under lubrication of liquid paraffin containing 2 wt % ZDDP, the ZDDP film absorbed on the frictional surfaces of the PTFE composites–GCr15 bearing steel friction pairs exhibits obvious antiwear properties; it greatly reduces the wear of pure PTFE and the PTFE composites filled with Pb, PbO, and MoS₂; and the wear of the PTFE composites can be reduced by one order of magnitude compared with that under lubrication of pure liquid paraffin. Meanwhile, the inorganic fillers Pb, PbO, and MoS₂ contained in PTFE have little effect on the absorption of ZDDP to the frictional surfaces, so they have little effect on the friction coefficients of the PTFE composites–GCr15 bearing steel friction pairs under the lubrication of liquid paraffin containing 2 wt % ZDDP. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1240–1247, 2000     

Tribological behavior of the polyamide composite coating filled with different fillers under dry sliding

The polyamide (PA) composite coating filled with the particles of microsized MoS₂, microsized graphite, and nano‐Al₂O₃, respectively, were prepared by flame spraying. The friction and wear characteristics of the PA coating and composite coating filled with the varied content of filler under dry sliding against stainless steel were comparatively investigated using a block‐ring tester. The morphologies of the worn surfaces and transfer films on the counterpart steel ring were observed on a scanning electron microscope. The result showed that the addition of fillers to the composite coatings changed significantly the friction coefficient and wear rate of the coatings. The composite coatings filled with a low level content of fillers showed lower wear rate than did pure PA coating under dry sliding; especially the MoS₂/PA composite coating had the lowest wear rate among these composite coatings. The composite coatings with a high level content of fillers had higher wear rate than did pure PA coating, except of the Al₂O₃/PA composite coating. The bonding strengths between the polymer matrix and fillers changed with the content of the fillers, which accounted for the differences in the tribological properties of the composite coatings filled with the varied content fillers. On the other hand, the difference in the friction and wear behaviors of the composite coatings and pure coating were attributed to the difference in their worn surface morphologies and transfer film characteristics. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Tribological properties of micro‐ and nanoparticles‐filled poly(etherimide) composites

It has been found that nano‐ or microsized inorganic particles in general enhance the tribological properties of polymer materials. In the present study, 5 vol % nano‐TiO₂ or micro‐CaSiO₃ was introduced into a polyetherimide (PEI) matrix composite, which was filled additionally with short carbon fibers (SCF) and graphite flakes. The influence of these inorganic particles on the sliding behavior was investigated with a pin‐on‐disc testing rig at room temperature and 150°C. Experimental results showed that both particles could reduce the wear rate and the frictional coefficient (μ) of the PEI composites under the applied testing conditions. At room temperature, the microparticles‐filled composites exhibited a lower wear rate and μ, while the nano‐TiO₂‐filled composites possessed the lowest wear rate and μ at elevated temperature. Enhancement in tribological properties with the addition of the nano‐particles was attributed to the formation of transfer layers on both sliding surfaces together with the reinforcing effect. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1678–1686, 2006     

Preparation and tribological properties of carbon fibre reinforced poly(vinylidene fluoride) composites

Abstract

The current study examines the tribological performance of poly(vinylidene fluoride) (PVDF) and carbon fibre reinforced poly(vinylidene fluoride) (CF/PVDF) under dry sliding condition. Different contents of carbon fibres (CFs) were employed as reinforcement. All filled and unfilled polyimide composites were tested against CGr15 ball and representative testing was performed. The effects of CF content on tribological properties of the composites were investigated. The worn surface morphologies of neat PVDF and its composites were examined by scanning electron microscopy and the wear mechanisms were discussed. Moreover, all filled PVDFs have superior tribological characteristics to unfilled PVDFs. The optimum wear reduction was obtained when the content of CF is 20 vol.-%.     

Mechanical and tribological properties of glass–epoxy composites with and without graphite particulate filler

The objectives of this research article is to evaluate the mechanical and tribological properties of glass‐fiber‐reinforced epoxy (G–E) composites with and without graphite particulate filler. The laminates were fabricated by a dry hand layup technique. The mechanical properties, including tensile strength, tensile modulus, elongation at break, and surface hardness, were investigated in accordance with ASTM standards. From the experimental investigation, we found that the tensile strength and dimensional stability of the G–E composite increased with increasing graphite content. The effect of filler content (0–7.5 wt %) and sliding distance on the friction and wear behavior of the graphite‐filled G–E composite systems were studied. Also, conventional weighing, determination of the coefficient of friction, and examination of the worn surface morphological features by scanning electron microscopy (SEM) were done. A marginal increase in the coefficient of friction with sliding distance for the unfilled composites was noticed, but a slight reduction was noticed for the graphite‐filled composites. The 7.5% graphite‐filled G–E composite showed a lower friction coefficient for the sliding distances used. The wear loss of the composites decreased with increasing weight fraction of graphite filler and increased with increasing sliding distance. Failure mechanisms of the worn surfaces of the filled composites were established with SEM. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2472–2480, 2007     

Tribological properties of polyimide fabric‐epoxy composites modified by hollow silica microspheres

The polyimide (PI) fabric/epoxy (EP) composites modified with different content of micro‐SiO₂ hollow spheres were prepared by dip‐coating and subsequently hot‐press process. For comparison, the pure EP and the unmodified PI fabric/EP composite were also fabricated. The differential scanning calorimetry was conducted to investigate the crosslinking reaction of composites. The results indicated that there exhibited a remarkable improvement in the mechanical and tribological properties of PI fabric/EP composites after incorporating the micro‐SiO₂. The best tribological properties were obtained when the content of micro‐SiO₂ was 2 wt%, whose wear rate was 71.9% lower than that of unmodified PI fabric/EP composite. The worn surfaces were observed by a scanning electron microscope to illustrate the friction mechanisms. Note that the skeleton network structure of fabric throughout the whole composites supported the matrix. At the same time, the microparticulates filled in the interstices of fabrics interwoven structure and the gaps between layers of fabrics, which propped up the skeleton network of fabric under the high frictional load and afford excellent interface between fabrics and EP. This ensures the outstanding tribological properties of PI fabric/EP composites. POLYM. COMPOS., 38:2283–2293, 2017. © 2015 Society of Plastics Engineers     

Friction and wear characteristics of metal sulfides and graphite‐filled PTFE composites under dry and oil‐lubricated conditions

Five kinds of polytetrafluoroethylene (PTFE)‐based composites, pure PTFE, PTFE + 30(v)% MoS₂, PTFE + 30(v)% PbS, PTFE + 30(v)% CuS, and PTFE + 30(v)% graphite (GR) composites, were first prepared. Then the friction and wear properties of these PTFE composites, sliding against GCr15‐bearing steel under both dry and liquid paraffin‐lubricated conditions, were studied by using an MHK‐500 ring‐on‐block wear tester. Finally, the worn surfaces and the transfer films of the PTFE composites formed on the surface of GCr15 bearing steel were investigated by using a scanning electron microscope (SEM) and an optical microscope, respectively. Experimental results show that filling with MoS₂, PbS, CuS, or graphite to PTFE can reduce the wear of the PTFE composites by two orders of magnitude compared to that of pure PTFE under dry friction conditions. However, the friction and wear‐reducing properties of these PTFE composites can be greatly improved by lubrication with liquid paraffin. Investigations of transfer films show that MoS₂, PbS, CuS, and graphite promote the transfer of the PTFE composites onto the surface of GCr15‐bearing steel under dry friction conditions, but the transfer of the PTFE composites onto the surface of GCr15‐bearing steel can be greatly reduced by lubrication with liquid paraffin. SEM examinations of worn surfaces show that with lubrication of liquid paraffin, the creation and development of the cracks occurred on the worn surfaces of the PTFE composites under load, which reduces the load‐supporting capacity of the PTFE composites. This would lead to the deterioration of the friction and wear properties of the PTFE composites under higher loads (>600N). © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 751–761, 1999     

Investigation on thermal stability and tribological properties of ZrB2 particles filling cyanate ester resin composites by experiments and numerical simulation

The thermal stability and tribological properties of cyanate ester (CE) composites filled with Zirconium boride (ZrB₂) particles were investigated by experimental and numerical simulation. The results of thermogravimetric analysis and differential scanning calorimetry showed that the thermal stability of composites was improved by introduction of ZrB₂ particles. The tribological properties of composites including friction coefficient and wear rate measured by pin‐on‐disk friction and wear tester were enhanced. Friction coefficient and wear rate of composites were decreased significantly with an increase of ZrB₂ particles content under dry and oil sliding conditions. The 5 wt% ZrB₂ particles reinforced CE resin composite presented optimal thermal stability and tribological performance due to good dispersion of ZrB₂ particles. The worn surfaces of composites were observed by scanning electron microscopy to explore wear mechanism, indicating that the dominant wear mechanism of composites was transformed from adhesive wear to abrasive wear after incorporation of ZrB₂ particles. Finite element model was established to study the distribution of friction stress. The results revealed that filling ZrB₂ particles in the friction process of composites could bear more friction stress than CE resin matrix, which further illustrated that abrasive wear is main wear mechanism of ZrB₂/CE resin composites. POLYM. ENG. SCI., 59:602–607, 2019. © 2018 Society of Plastics Engineers     

Epoxy composite reinforced with three‐dimensional polyimide fiber felt: Fabrication and tribological properties investigation

Novel epoxy (EP) composite reinforced with three‐dimensional (3D) polyimide (PI) fiber felt (PI_3D/EP) is first fabricated by vacuum assisted resin transfer molding. The tribological behaviors of pure EP and PI_3D/EP composite under dry sliding and water lubricated condition are comparatively studied. Results indicate that both wear rates and friction coefficients of PI_3D/EP composite are lower than those of pure EP. The wear resistance of PI_3D/EP composite is 9.8 times higher than that of pure EP under dry sliding of 1.5 MPa and 0.76 m s^?1 while a 27‐fold increase is achieved under water lubricated condition. The wear mechanisms of PI_3D/EP composite are investigated based on tribological testing results and scanning electron microscopy observations. The PI fiber felt provides strong 3D structure supports to sustain most of the loads on the composite, improving the mechanical and tribological properties significantly. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44160.     

Tribological behavior of short‐fiber‐reinforced polyimide composites under dry‐sliding and water‐lubricated conditions

Polyimide composites reinforced with short‐cut fibers such as carbon, glass, and quartz fibers were fabricated by the polymerization of monomer reactants process. The mechanical properties of the composites with different fiber contents were evaluated. The friction and wear properties of the polyimide and its composites were investigated under dry‐sliding and water‐lubricated conditions. The results indicated that the short‐carbon‐fiber‐reinforced polyimide composites had better tensile and flexural strengths and improved tribological properties in comparison with glass‐fiber‐ and quartz‐fiber‐reinforced polyimide composites. The incorporation of short carbon fibers into the polyimide contributed to decreases in the friction coefficient and wear rate under both dry and water‐lubricated conditions and especially under water lubrication because of the boundary lubrication effect of water. The polyimide and its composites were characterized by plastic deformation, microcracking, and spalling under both dry and water‐lubricated conditions, which were significantly abated under the water‐lubricated condition. The glass and quartz fibers were easily abraded and broken; the broken fibers transferred to the mating metal surface and increased the surface roughness of mating stainless steel, which led to the wear rate increasing for the glass‐fiber‐ and quartz‐fiber‐reinforced polyimide composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Fiber hybrid polyimide‐based composites reinforced with carbon fiber and poly‐p‐phenylene benzobisthiazole fiber: Tribological behaviors under sea water lubrication

Fiber hybrid polyimide‐based (PI‐based) composites reinforced with carbon fiber (CF) and poly‐p‐phenylene benzobisthiazole (PBO) fiber of different volume fractions were fabricated by means of hot press molding technique, and their mechanical properties and tribological behaviors under sea water lubrication were systematically investigated in relation to the synergism of CF and PBO fiber. Results showed that the incorporation of CF or PBO fiber improved the tensile strength, hardness, and wear resistance of PI. More importantly, because of the synergistic enhancement effect between CF and PBO fiber on PI matrix, the combination of 10%CF and 5%PBO fiber reinforced PI‐based composite had the best mechanical and tribological properties, showing promising application in ocean environment. POLYM. COMPOS., 37:1650–1658, 2016. © 2014 Society of Plastics Engineers     

Tribological behaviors of carbon series additions reinforced CF/PTFE composites at high speed

The tribological, mechanical, and thermal properties of carbon series additions reinforced CF/PTFE composites at high speed were investigated. In this work, carbon fiber (CF) filled polytetrafluoroethylene (PTFE) composites, which have excellent tribological properties under normal sliding speed (1.4 m/s), were filled with some carbon materials [graphene (GE), carbon nanotubes (CNTs) and graphite (Gr)] respectively to investigate the tribological properties of CF/PTFE composites at high sliding speed (2.1 and 2.5 m/s). The results reveal that the carbon series additions can improve the friction and anti‐wear performances of CF/PTFE, and GE is the most effective filler. The wear rate of 0.8 wt % GE/CF/PTFE was decreased by 50 ? 55%, 55 ? 60%, 40 ? 45% at 1.4, 2.1, and 2.5 m/s compared with CF/PTFE. SEM study shows GE could be helpful to form smooth and continuous transfer film on the surface of counterparts. Meanwhile, GE can improve its tensile strength and elastic modulus obviously. Thin layer structure of GE could enhance the thermal conductivity, which can be helpful to dissipate heat of CF/PTFE composites wear surface. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43236.     

Tribological behavior of carbon nanotube and polytetrafluoroethylene filled polyimide composites under different lubricated conditions

The friction and wear behavior of polyimide (PI) composites reinforced with carbon nanotube (CNT) and polytetrafluoroethylene (PTFE) were comparatively evaluated under dry sliding, water‐, oil‐ or alkali‐lubricated condition. The wear mechanisms of the composites were also discussed. Results indicate that, when comparison with the dry friction situation, PI‐based composites results lower friction coefficients and wear rates under oil‐ or alkali‐lubricated condition. The lowest wear rate of the CNT/PTFE/PI composite is recorded as 1.2 × 10⁻⁶ mm³/Nm during the composite sliding in alkali, which is only about 40% of the value sliding under dry friction condition. The worn surface of neat PI under dry sliding is characterized by severe adhesive wear, whereas abrasive wear is the main character for CNT/PTFE/PI composites. The worn surfaces of CNT/PTFE/PI composites sliding in oil or alkali lubricated condition are smoother than those under dry or water condition. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011