Controlled degradation of polylactic acid grafting N‐vinyl pyrrolidone induced by gamma ray radiation

Polylactic acid (PLA) films were surface modified by gamma ray irradiation‐induced grafting of N‐vinyl pyrrolidone (NVP). The in vitro degradation behavior of polylactic acid grafting N‐vinyl pyrrolidone (PLA‐g‐PVP) copolymer was analyzed in terms of weight loss, molecular weight, and thermal properties. Grafting NVP significantly accelerated the degradation of PLA. The mass losses of the copolymers, which were less than that of pure PLA at the beginning of the degradation period, sharply accelerated with increasing degradation time. Moreover, the crystallization temperature decreased with increasing degradation time in the same graft ratio, and the degree of crystallinity increased. Cytotoxicity experiments and animal experiments in vivo were carried out to evaluate the biocompatibility of PLA‐g‐PVP copolymer. Varying graft ratios of PVP could control the degradation rate of copolymers, and thus broadening the applications of this material, such as in tissue engineering scaffolds, drug delivery, and prevention of postsurgical adhesion. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Novel bioresorbable hydrogels prepared from chitosan‐graft‐polylactide copolymers

A series of biodegradable chitosan‐graft‐polylactide (CS‐g‐PLA) copolymers were prepared by grafting of poly(L ‐lactide) (PLLA) or poly(D ‐lactide) (PDLA) precursor to the backbone of chitosan using N,N′‐carbonyldiimidazole as coupling agent. The composition of the copolymers was varied by adjusting the chain length of PLA as well as the ratio of chitosan to PLA. The copolymers synthesized via this ‘graft‐onto’ method present interesting properties as shown by NMR and infrared spectroscopy, gel permeation chromatography and solubility tests. Hydrogels were prepared by mixing water‐soluble CS‐g‐PLLA and CS‐g‐PDLA solutions. Gelation was assigned to stereocomplexation between PLLA and PDLA blocks as evidenced by differential scanning calorimetry and wide‐angle X‐ray diffraction measurements. Thymopentin (TP5) was taken as a model drug to evaluate the potential of these CS‐g‐PLA hydrogels as drug carriers. An initial burst and a final release up to 82% of TP5 were observed from high‐performance liquid chromatography analysis. Copyright © 2011 Society of Chemical Industry     

Thiol–ene addition enables tailored synthesis of poly(2‐oxazoline)‐graft‐poly(vinyl pyrrolidone) copolymers for binder jetting 3D printing

The continued interest in graft copolymer architectures arises from their unique solution properties and potential for a myriad of applications ranging from drug delivery to adhesives. Poly(vinyl pyrrolidone) (PVP) represents a popular amorphous, water‐soluble polymer used as a polymeric binder in binder jetting additive manufacturing, as fillers in cosmetic products, and for subcutaneous drug delivery systems. This report describes the synthesis of poly(2‐oxazoline) and PVP graft copolymers using a ‘grafting to’ methodology with an efficient thiol–ene ‘click’ reaction. Copolymerization of 2‐methyl‐2‐oxazoline and 2‐(3‐butenyl)‐2‐oxazoline introduced pendent vinyl grafting sites with a predictable absolute number‐average molecular weight. In parallel, reversible addition‐fragmentation chain‐transfer polymerization and subsequent aminolysis yielded well‐defined, oligomeric, thiol‐terminated PVP. Thiol–ene click chemistry enabled the formation of poly(2‐oxazoline)‐graft‐poly(vinyl pyrrolidone) (PMeOx‐g‐PVP) copolymers with varying mole percent grafting sites and PVP graft length. ¹H NMR spectroscopy, aqueous SEC with multiangle light scattering (SEC‐MALS), and bromine titrations confirmed chemical structure, and DSC with TGA elucidated thermal transitions. Aqueous SEC‐MALS and ¹H NMR spectroscopy also determined absolute number‐ and weight‐average molecular weights and average grafting levels, which revealed optimal reaction conditions. Zero‐shear viscosities of 5 and 10 wt% solutions in deionized water for each graft copolymer compared to their linear analogs demonstrated a significant (ca 31%) decrease in viscosity at the same number‐average molecular weight. This decrease in solution viscosity suggested PMeOx‐g‐PVP copolymers as exceptional alternatives to linear analogs for aqueous‐based, binder jetting additive manufacturing.     

Antifouling microfiltration membranes prepared from poly(vinylidene fluoride)‐graft‐Poly(N‐ vinyl pyrrolidone) powders synthesized via pre‐irradiation induced graft polymerization

Poly(vinylidene fluoride) (PVDF) powders were grafted with N‐vinyl pyrrolidone using the pre‐irradiation induced graft polymerization technique. The effects of reaction time, absorbed dose, and monomer concentration on the degree of grafting were investigated, and the grafted PVDF powders were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, and differential scanning calorimetry. The grafted PVDF powders were also cast into microfiltration (MF) membranes via the phase‐inversion method. The contact angle and water uptake were measured. The membrane morphology was studied by scanning electron microscopy, and the water filtration properties of the membranes were tested. The antifouling properties were determined through measurements of the recovery percentage of pure water flux after the MF membranes were fouled with bovine serum albumin solution. The results confirmed that the existence of poly(N‐vinyl pyrrolidone) (PVP) graft chains improved the hydrophilicity and antifouling properties of the MF membranes cast from PVDF‐g‐PVP powders. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis of poly(vinyl alcohol)‐graft‐poly(ε‐caprolactone) and poly(vinyl alcohol)‐graft‐poly(lactide) in melt with magnesium hydride as catalyst

Grafting of poly(ε‐caprolactone) (PCL) and poly(lactide) (PLA) chains on poly(vinyl alcohol) backbone (PVA degree of hydrolysis 99%) was investigated using MgH₂ environmental catalyst and melt‐grown ring‐opening polymerization (ROP) of ε‐caprolactone (CL) and L ‐lactide (LA), that avoiding undesirable toxic catalyst and solvent. The ability of MgH₂ as catalyst as well as yield of reaction were discussed according to various PVA/CL/MgH₂ and PVA/LA/MgH₂ ratio. PVA‐g‐PCL and PVA‐g‐PLA were characterized by ¹H‐ and ¹³C‐NMR, DSC, SEC, IR. For graft copolymers easily soluble in tetrahydrofuran (THF) or chloroform, wettability and surface energy of cast film varied in relation with the length and number of hydrophobic chains. Aqueous solution of micelle‐like particles was realized by dissolution in THF then addition of water. Critical micelle concentration (CMC) decreased with hydrophobic chains. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Part 7. Effects of poly(L‐lactide‐co‐ϵ‐caprolactone) on morphology,structure, crystallization,and physical properties of blends of poly(L‐lactide) and poly(ϵ‐caprolactone)

Blended films of poly(L ‐lactide) [ie poly(L ‐lactic acid)] (PLLA) and poly(?‐caprolactone) (PCL) without or mixed with 10 wt% poly(L ‐lactide‐co‐?‐caprolactone) (PLLA‐CL) were prepared by solution‐casting. The effects of PLLA‐CL on the morphology, phase structure, crystallization, and mechanical properties of films have been investigated using polarization optical microscopy, scanning electron microscopy, differential scanning calorimetry and tensile testing. Addition of PLLA‐CL decreased number densities of spherulites in PLLA and PCL films, and improved the observability of spherulites and the smoothness of cross‐section of the PLLA/PCL blend film. The melting temperatures (T_m) of PLLA and PCL in the films remained unchanged upon addition of PLLA‐CL, while the crystallinities of PLLA and PCL increased at PLLA contents [X_PLLA = weight of PLLA/(weight of PLLA and PCL)] of 0.4–0.7 and at most of the X_PLLA values, respectively. The addition of PLLA‐CL improved the tensile strength and the Young modulus of the films at X_PLLA of 0.5–0.8 and of 0–0.1 and 0.5–0.8, respectively, and the elongation at break of the films at all the X_PLLA values. These findings strongly suggest that PLLA‐CL was miscible with PLLA and PCL, and that the dissolved PLLA‐CL in PLLA‐rich and PCL‐rich phases increased the compatibility between these two phases. © 2003 Society of Chemical Industry     

Poly(N‐isopropylacrylamide‐co‐hydroxyethyl methacrylate) graft copolymers and their application as carriers for drug delivery system

Poly(N‐isopropylacrylamide‐co‐hydroxyethyl methacrylate) [P(NIPAM‐co‐HEMA)] copolymer was synthesized by controlled radical polymerization from respective N‐isopropylacrylamide (NIPAM) and hydroxyethyl methacrylate (HEMA) monomers with a predetermined ratio. To prepare the thermosensitive and biodegradable nanoparticles, new thermosensitive graft copolymer, poly(L ‐lactide)‐graft‐poly(N‐isoporylacrylamide‐co‐hydroxyethyl methacrylate) [PLLA‐g‐P(NIPAM‐co‐HEMA)], with the lower critical solution temperature (LCST) near the normal body temperature, was synthesized by ring opening polymerization of L ‐lactide in the presence of P(NIPAM‐co‐HEMA). The amphiphilic property of the graft copolymers was formed by the grafting of the PLLA hydrophobic chains onto the PNIPAM based hydrophilic backbone. Therefore, the graft copolymers can self‐assemble into uniformly spherical micelles ò about 150–240 nm in diameter as observed by the field emission scanning electron microscope and dynamic light scattering. Dexamethasone can be loaded into these nanostructures during dialysis with a relative high loading capacity and its in vitro release depends on temperature. Above the LCST, most of the drugs were released from the drug‐loaded micelles, whereas a large amount of drugs still remains in the micelles after 48 h below the LCST. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of dimethyl sulfoxide on synthesis of thermoplastic cellulose‐Graft‐poly(l‐lactide) copolymer using ionic liquid as reaction media

In this study, ring‐opening graft polymerization of l ‐lactide onto cellulose was carried out homogeneously in ionic liquid (IL)/dimethyl sulfoxide (DMSO) co‐solvent as a reaction media. Through the effective control of high viscosity and steric hindrance caused by the interaction between the IL and the hydroxyl group of cellulose by adding DMSO as a co‐solvent, cellulose‐graft‐poly(l ‐lactide) (Cell‐g‐PLLA) copolymer with higher substitution efficiency was successfully prepared, at relatively low concentration of l ‐lactide. The maximum values of molar substitution, degree of lactyl substitution, and degree of polymerization of poly(l ‐lactide) in the copolymer were 3.76, 1.74, and 2.16, respectively, determined by ¹H‐NMR. The prepared cell‐g‐PLLA copolymers showed thermal plasticization with a glass transition temperature of 155°C. In addition, the thermal processibility could be improved as the amount of grafted PLLA in the copolymer increased. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41331.     

Characterization of the mechanical and thermal properties and morphological behavior of biodegradable poly(L‐lactide)/poly(ε‐caprolactone) and poly(L‐lactide)/poly(butylene succinate‐co‐L‐lactate) polymeric blends

Two series of biodegradable polymer blends were prepared from combinations of poly(L ‐lactide) (PLLA) with poly(?‐caprolactone) (PCL) and poly(butylene succinate‐co‐L ‐lactate) (PBSL) in proportions of 100/0, 90/10, 80/20, and 70/30 (based on the weight percentage). Their mechanical properties were investigated and related to their morphologies. The thermal properties, Fourier transform infrared spectroscopy, and melt flow index analysis of the binary blends and virgin polymers were then evaluated. The addition of PCL and PBSL to PLLA reduced the tensile strength and Young's modulus, whereas the elongation at break and melt flow index increased. The stress–strain curve showed that the blending of PLLA with ductile PCL and PBSL improved the toughness and increased the thermal stability of the blended polymers. A morphological analysis of the PLLA and the PLLA blends revealed that all the PLLA/PCL and PLLA/PBSL blends were immiscible with the PCL and PBSL phases finely dispersed in the PLLA‐rich phase. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation of diblock copolymers consisting of methoxy poly(ethylene glycol) and poly(ε‐caprolactone)/poly(L‐lactide) and their degradation property

Methoxy poly(ethylene glycol)‐b‐poly(ε‐caprolactone) (MPEG‐PCL) or MPEG‐b‐poly(L ‐lactide) (MPEG‐PLLA) diblock copolymers were prepared by the polymerization of CL or LA, using MPEG as an initiator in the presence of stannous octoate. MPEG‐b‐poly(ε‐caprolactone‐ran‐L ‐lactide) (MPEG‐PCLA) diblock copolymers with different chemical composition of PCL and PLLA were also prepared by adjusting the amount of CL and LA from MPEG in the presence of stannous octoate. In degradation study, the degradation of the MPEG‐PCLA diblock copolymers mainly depends on the PCL and PLLA segments present in their structure. MPEG‐PCLA, with intermediate ratio of PCL and PLLA segment, completely degraded after 14 weeks. Meanwhile, partially degraded MPEG‐PCLA segments and parent MPEG segments were observed at higher PCL or PLLA segment contents. Introduction of PLLA into the PCL segments caused a lowering of the crystallinity of the diblock copolymers, thus, inducing a faster incoming of water into the copolymers. We confirmed that the diblock copolymers, with lower degree of crystallinity, have degraded more rapidly. POLYM. ENG. SCI., 46: 1242–1249, 2006. © 2006 Society of Plastics Engineers     

Poly(vinyl pyrrolidone‐co‐vinyl acetate)‐graft‐poly(ε‐caprolactone) as a compatibilizer for cellulose acetate/poly(ε‐caprolactone) blends

Poly(vinyl pyrrolidone‐co‐vinyl acetate)‐graft‐poly(ε‐caprolactone) (PVPVAc‐g‐PCL) was synthesized by radical copolymerization of N‐vinyl‐2‐pyrrolidone (VP)/vinyl acetate (VAc) comonomer and PCL macromonomer containing a reactive 2‐hydroxyethyl methacrylate terminal. The graft copolymer was designed in order to improve the interfacial adhesiveness of an immiscible blend system composed of cellulose acetate/poly(ε‐caprolactone) (CA/PCL). Adequate selections of preparation conditions led to successful acquisition of a series of graft copolymer samples with different values of molecular weight ( ), number of grafts (n), and segmental molecular weight of PVPVAc between adjacent grafts (M_n (between grafts)). Differential scanning calorimetry measurements gave a still immiscible indication for all of the ternary blends of CA/PCL/PVPVAc‐g‐PCL (72 : 18 : 10 in weight) that were prepared by using any of the copolymer samples as a compatibilizer. However, the incorporation enabled the CA/PCL (4 : 1) blend to be easily melt‐molded to give a visually homogeneous film sheet. This compatibilizing effect was found to be drastically enhanced when PVPVAc‐g‐PCLs of higher and M_n (between grafts) and lower n were employed. Scanning electron microscopy revealed that a uniform dispersion of the respective ingredients in the ternary blends was attainable with an assurance of the mixing scale of several hundreds of nanometers. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation of biodegradable crosslinking agents and application in PVP hydrogel

Firstly, biodegradable crosslinking agents (BCA) were synthesized by ring‐opening polymerization reaction of lactide, four kinds of which with different molecular weights were got by means of changing the ratio of DL ‐lactide(LA) and glycerol(GL). Then a series of poly(N‐vinyl pyrrolidone) (PVP) hydrogels were prepared successfully by radical polymerization of BCA and N‐vinyl pyrrolidone(NVP). Both the ratio of NVP/BCA and the molecular weight of BCA were used to control the performance of PVP hydrogels, which were measured in terms of the ratio of swelling, contact angle, mechanical properties, and biodegradability in vitro. This study showed that increasing both the ratio of NVP/BCA and the molecular weight of BCA resulted in a low crosslinking density of the hydrogels. The crosslinking density played an important role in determining the properties of biodegradable PVP hydrogels. Both the ratio of NVP/BCA and the molecular weight of BCA contributed to high ratio of swelling. A smaller amount of crosslinking agent caused a lower contact angle, while the molecular weight of BCA had little effect on it. In terms of mechanics of hydrogels on both dry and wet conditions, tensile modulus decreased along with decreasing BCA, while the extension at break increased at the beginning and decreased at the end. In the end, measured by mass loss, biodegradability in vitro of hydrogels had two stages: an initial stage with approximately constant loss of mass (stage 1) followed by a stage with rapid mass loss (stage 2). Both increased content and molecular weight of BCA improved the degradation rate of the hydrogels. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1515–1521, 2006     

Ring‐opening graft polymerization of L‐lactide onto starch granules in an ionic liquid

A room temperature ionic liquid 1‐allyl‐3‐methylimidazolium chloride ([AMIM]Cl) was a promising direct solvent for starch and nonderivitizing solvent for starch‐effective dissolution, in which the ring‐opening graft polymerization (ROGP) of L ‐lactide (L ‐LA) onto starch chains was carried out homogeneously. The obtained starch grafted poly(L ‐lactide) (starch‐g‐PLLA) was characterized by FTIR, ¹³C NMR, DSC, and WAXD, and the good adhesion between the two components was evidenced by SEM observations although the chains of grafted PLLA were not long. The grafting efficiency of PLLA reached 30% when the ROGP proceeded at 100°C for 10 h with L ‐LA/starch 0.5 : 1 (wt/wt) and stannous octoate (Sn(Oct)₂) as a catalyst, which was calculated according to a standard curve newly created by FTIR method. The homopolymerization of L ‐LA and the disconnection of grafted PLLA from starch‐g‐PLLA were the main competition reactions. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and characterization of AB‐type copolymers poly(L‐lactide)‐block‐poly(methyl methacrylate) via a convenient route combining ROP and ATRP from a dual initiator

Diblock copolymers of poly(L ‐lactide)‐block‐poly(methyl methacrylate) (PLLA‐b‐PMMA) were synthesized through a sequential two‐step strategy, which combines ring‐opening polymerization (ROP) and atom transfer radical polymerization (ATRP), using a bifunctional initiator, 2,2,2‐trichloroethanol. The trichloro‐terminated poly(L ‐lactide) (PLLA‐Cl) with high molecular weight (M_n,GPC = 1–12 × 10⁴ g/mol) was presynthesized through bulk ROP of L ‐lactide (L ‐LA), initiated by the hydroxyl group of the double‐headed initiator, with tin(II) octoate (Sn(Oct)₂) as catalyst. The second segment of the block copolymer was synthesized by the ATRP of methyl methacrylate (MMA), with PLLA‐Cl as macroinitiator and CuCl/N,N,N′,N″,N″‐pentamethyldiethylenetriamine (PMDETA) as catalyst, and dimethyl sulfoxide (DMSO) was chosen as reaction medium due to the poor solubility of the macroinitiator in conventional solvents at the reaction temperature. The trichloroethoxyl terminal group of the macroinitiator was confirmed by Fourier transform infrared spectroscopy (FTIR) and ¹H‐NMR spectroscopy. The comprehensive results from GPC, FTIR, ¹H‐NMR analysis indicate that diblock copolymers PLLA‐b‐PMMA (M_n,GPC = 5–13 × 10⁴ g/mol) with desired molecular composition were obtained by changing the molar ratio of monomer/initiator. DSC, XRD, and TG analyses establish that the crystallization of copolymers is inhibited with the introduction of PMMA segment, which will be beneficial to ameliorating the brittleness, and furthermore, to improving the thermal performance. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Novel biodegradable amphiphilic poly(ε‐caprolactone)/poly(N‐vinylpyrrolidone) blends via successive in situ polymerizations

In this study, biodegradable blends of poly(ε‐caprolactone) (PCL) and poly(N‐vinylpyrrolidone) (PVP) were prepared by a new strategy in the following steps: (1) free radical polymerization of N‐vinyl‐2‐pyrrolidone (NVP) in ε‐caprolactone (CL); (2) ring‐opening polymerization of ε‐caprolactone in the presence of PVP to obtain the target blends. The structure of the blends was confirmed by FTIR and ¹H NMR, and the molecular weight of PCL and PVP were determined by GPC. SEM study revealed that this polymerization method could decrease the disperse phase size and improve the interphase when compared with solution‐blending method. The phase inversion occurred when PVP content was 15–20 wt %. Subsequently, the PCL sphere dispersed in PVP matrix and its size decreased with the increase of PVP content. The contact angle results showed that PVP has a profound effect on hydrophilic properties of PCL/PVP blends. PCL/PVP blends are believed to be promising for drug delivery, cell therapy, and other biomedical applications. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Specific interactions in 4‐hydroxybenzoic acid/poly(2‐vinylpyridine)/poly(N‐vinyl‐2‐pyrrolidone) blends

The specific interactions in ternary 4‐hydroxybenzoic acid (HBA)/poly(2‐vinylpyridine) (P2VPy)/poly(N‐vinyl‐2‐pyrrolidone) (PVP) blends were studied by differential scanning calorimetry, Fourier transform infrared (FTIR) spectroscopy, and electron microscopy. FTIR study shows the existence of hydrogen‐bonding interactions between HBA and P2VPy as well as PVP. The addition of a sufficiently large amount of HBA produces a blend showing one glass‐transition temperature (T_g). Microscopic study shows a drastic reduction in domain size in single‐T_g blends. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 901–907, 2001     

Synthesis and characterization of poly(L‐lactic acid)‐b‐poly(ethylene terephthalate‐co‐sebacate)‐b‐poly(L‐lactic acid) copolyesters

Random copolyester namely, poly(ethylene terephthalate‐co‐sebacate) (PETS), with relatively lower molecular weight was first synthesized, and then it was used as a macromonomer to initiate ring‐opening polymerization of l ‐lactide. ¹H NMR quantified composition and structure of triblock copolyesters [poly(l ‐lactic acid)‐b‐poly(ethylene terephthalate‐co‐sebacate)‐b‐poly(l ‐lactic acid)] (PLLA‐PETS‐PLLA). Molecular weights of copolyesters were also estimated from NMR spectra, and confirmed by GPC. Copolyesters exhibited different solubilities according to the actual content of PLLA units in the main chain. Copolymerization effected melting behaviors significantly because of the incorporation of PETS and PLLA blocks. Crystalline morphology showed a special pattern for specimen with certain composition. It was obvious that copolyesters with more content of aromatic units of PET exhibited increased values in both of stress and modulus in tensile test. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Asymmetric membranes fabricated from poly(acrylonitrile‐co‐N‐vinyl‐2‐pyrrolidone)s with excellent biocompatibility

Poly(acrylonitrile‐co‐N ‐vinyl‐2‐pyrrolidone)s (PANCNVPs) show excellent biocompatibility. In this work, PANCNVPs with different contents of N‐vinyl‐2‐pyrrolidone (NVP) were fabricated into asymmetric membranes by the phase inversion method. The surface chemical composition of the resultant membranes was determined by Fourier transform infrared spectroscopy–attenuated total reflection. Field emission scanning electron microscopy was used to examine the surface and cross section morphologies of the membranes. It was found that the morphologies hardly change with the increase of NVP content in PANCNVP, while the deionized water flux increases remarkably and the bovine serum albumin (BSA) retention decreases slightly. Experiment of dynamic BSA solution filtration was carried out to evaluate the antifouling properties of the studied membranes. The relative flux reduction of PANCNVP membrane containing 30.9 wt % of NVP is 25.9%, which is far smaller than that of the polyacrylonitrile membrane (68.8%). Results deduce that this improvement comes from the excellent biocompatibility of NVP moieties instead of the hydrophilicity change, because the water contact angles of these membranes fluctuate between 60 and 70°. Results from the membranes using poly(N‐vinyl‐2‐pyrrolidone) (PVP) as an additive confirm that, to a certain extent, the PANCNVP membranes show the advantages of antifouling compared with the polyacrylonitrile/PVP blending membrane. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4577–4583, 2006     

Compatibility of poly(butadiene‐co‐acrylonitrile) with poly(L‐lactide) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)

Poly(L ‐lactide) (PLLA) and poly(3‐hydrobutyrate‐co‐3‐hydroxyvalerate) (PHBV) were blended with poly(butadiene‐co‐acrylonitrile) (NBR). Both PLLA/NBR and PHBV/NBR blends exhibited higher tensile properties as the content of acrylonitrile unit (AN) of NBR increased from 22 to 50 wt %. However, two separate glass transition temperatures (T_g) appeared in PLLA/NBR blends irrespective of the content of NBR, revealing that PLLA was incompatible with NBR. In contrast, a single T_g, which shifted along with the blend composition, was observed for PHBV/NBR50 blends. Moreover NBR50 suppressed the crystallization of PHBV, indicating that PHBV was compatible with NBR50. Decrease of both elongation modulus and stress at maximum load was less significant and increase of elongation at break was more pronounced in PHBV/NBR50 blends than in PLLA/NBR50 blends. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3508–3513, 2004     

Reactive blending of poly(L‐lactic acid) with poly(ethylene‐co‐vinyl alcohol)

Poly(L ‐lactic acid) (PLLA) was blended with poly(ethylene‐co‐vinyl alcohol) (EVOH) in the presence of an esterification catalyst to induce reaction between the hydroxyl groups of EVOH and the terminal carboxylic group of PLLA. Nascent low‐molecular‐weight PLLA, obtained from a direct condensation polymerization of L ‐lactic acid in bulk state, was used for the blending. Domain size of the PLLA phase in the graft copolymer was much smaller than that corresponding to a PLLA/EVOH simple blend. The mechanical properties of the graft copolymer were far superior to those of the simple blend, and the graft copolymer exhibited excellent mechanical properties even though the biodegradable fraction substantially exceeded the percolation level. The grafted PLLA reduced the crystallization rate of the EVOH moiety. Melting peak temperature (T_m) of the PLLA phase was not observed until the content of PLLA in the graft reaction medium went over 60 wt %. The modified Sturm test results demonstrated that biodegradation of EVOH‐g‐PLLA took place more slowly than that of an EVOH/PLLA simple blend, indicating that the chemically bound PLLA moiety was less susceptible to microbial attack than PLLA in the simple blend. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 886–890, 2005