Structure and properties of new thermoforming bionanocomposites based on chitin whisker‐graft‐polycaprolactone

Thermoformable bionanocomposites of chitin whisker‐graft‐polycaprolactone (CHW‐g‐PCL) were synthesized by initiating the ring‐opening polymerization of caprolactone monomer onto the CHW surface under microwave radiation. In this case, the “graft from” strategy contributed to long and dense “plasticizing” PCL tails onto the CHW surface as the key of thermoforming, and, therefore, such bionanocomposites were injection‐molded as the sheets with a structure of cocontinuous phase mediated with the entanglement of grafted PCL chains. The structure and properties of the molded CHW‐g‐PCL sheets were investigated by FTIR, XRD, SEM, DSC, DMTA, contact angle measurement, and tensile test. With an increase of the PCL content in CHW‐g‐PCL, the strength and elongation as well as the hydrophobicity of the nanocomposites increased at one time. This is the first report on the thermoformable polymer‐grafted nanocrystal derived from natural polysaccharide. Moreover, such new bionanocomposites with good mechanical performances could have great potential applications. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effects of polymer‐grafted natural nanocrystals on the structure and mechanical properties of poly(lactic acid): A case of cellulose whisker‐graft‐polycaprolactone

In this work, polysaccharide nanocrystals—rodlike cellulose whiskers (CWs)—were surface‐grafted with polycaprolactone (PCL) via microwave‐assisted ring‐opening polymerization, and filaceous cellulose whisker‐graft‐polycaprolactone (CW‐g‐PCL) nanoparticles were produced. Moreover, the resultant nanoparticles were incorporated into poly(lactic acid) (PLA) as a matrix, and they showed superior function for enhancing the mechanical performance of PLA‐based materials in comparison with platelet‐like nanoparticles of starch nanocrystal‐graft‐PCL. The optimal loading level of CW‐g‐PCL was 8 wt %, and this resulted in simultaneous enhancements of the strength and elongation of approximately 1.9‐ and 10.7‐fold, respectively, over those of the neat PLA material. In this case, the rigid CW nanoparticles contributed to the endurance of higher stress, whereas the grafted PCL chains improved the association between the PLA matrix and the CW‐g‐PCL filler and hence facilitated the transfer of stress to the rigid CW nanoparticles. Furthermore, such a fully biodegradable PLA‐based nanocomposite shows great potential for environmentally friendly materials because of its high mechanical performance. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effects of starch nanocrystal‐graft‐polycaprolactone on mechanical properties of waterborne polyurethane‐based nanocomposites

Based on a “graft from” strategy, the surface of starch nanocrystals (StN) were functionalized by grafting with polycaprolactone (PCL) chains via microwave assisted ring‐opening polymerization (ROP). The modified natural nanoparticles were then compounded into a PCL‐based waterborne polyurethane as matrix. The structural and mechanical properties of the WPU/StN‐g‐PCL nanocomposites were characterized by XRD, FTIR, SEM, DSC, DMA, and tensile testing. It was interesting to note that a loading‐level of 5 wt % StN‐g‐PCL resulted in a simultaneous enhancement of tensile strength and elongation at break, both of which were higher than those of neat WPU. This enhancement was attributed to the uniform dispersion of StN‐g‐PCL because of its nano‐scale size, the increased entanglements mediated with grafted PCL chains, and the reinforcing function of rigid StN. Increasing the StN‐g‐PCL content however caused the StN‐g‐PCL to self‐aggregate as crystalline domains, which impeded improvement in tensile strength and elongation at break, but significantly enhanced Young's modulus. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Paper‐sheet biocomposites based on wood pulp grafted with poly(ε‐caprolactone)

Kraft pulp fibers were used as substrates for the grafting of poly(ε‐caprolactone) (PCL) from available hydroxyl groups through ring‐opening polymerization, targeting three different chain lengths (degree of polymerization): 120, 240, and 480. In a paper‐making process, paper‐sheet biocomposites composed of grafted fibers and neat pulp fibers were prepared. The paper sheets possessed both the appearance and the tactility of ordinary paper sheets. Additionally, the sheets were homogenous, suggesting that PCL‐grafted fibers and neat fibers were compatible, as demonstrated by both Fourier transform infrared spectroscopy microscopy and through dye‐labeling of the PCL‐grafted fibers. Finally, it was shown that the paper‐sheet biocomposites could be hot‐pressed into laminate structures without the addition of any matrix polymer; the adhesive joint produced could even be stronger than the papers themselves. This apparent and sufficient adhesion between the layers was thought to be due to chain entanglements and/or co‐crystallization of adjacent grafted PCL chains within the different paper sheets. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42039.     

Structure and Mechanical Properties of Poly(lactic acid) Filled with (Starch nanocrystal)‐graft‐poly(ε‐caprolactone)

Poly(ε‐caprolactone) (PCL) was grafted to the surface of starch nanocrystals (StN) via microwave‐assisted ROP. The resultant nanoparticles were then incorporated into a poly(lactic acid) matrix to produce fully‐biodegradable nanocomposites with good mechanical properties. A loading level of 5 wt.‐% StN‐g‐PCL resulted in simultaneous enhancements of strength and elongation. The StN‐g‐PCL self‐aggregated as rubbery microparticles to enhance the elongation by ca. 10‐fold over that of neat PLA. Meanwhile, the grafted PCL chains were miscible with PLA and formed a stress‐transferring interface to the StN, providing a reinforcing function.

     

Fabrication of a poly(N‐vinyl‐2‐pyrrolidone) modified macroporous polypropylene membrane via one‐pot reversible‐addition fragmentation chain‐transfer polymerization and click chemistry

In this study, a macroporous polypropylene membrane (MPPM) was grafted with hydrophilic poly(N‐vinyl‐2‐pyrrolidone) (PNVP) based on a one‐pot reversible‐addition fragmentation chain transfer (RAFT) polymerization and click chemistry. First, we prepared the clickable membrane by bromination and following S_N2 nucleophilic substitution reaction; then, click chemistry and RAFT polymerization were performed in one‐pot to graft PNVP to the MPPM surface. The surface characterizations, including attenuated total reflectance/Fourier transform infrared spectroscopy, X‐ray photoelectron spectroscopy, and field‐emission scanning electron microscopy, illustrated that PNVP was really grafted onto the MPPM surface. The permeation and antifouling characteristics of the MPPMs were measured by the filtration of a bovine serum albumin dispersion; this showed that in contrast to the nascent membrane, the grafted membrane efficiently obstructed protein molecules because of the compactly grafted polymer chains. The hydrophilicity and antifouling properties of MPPM were greatly ameliorated after modification. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42649.     

Preparation and conductive properties of polycaprolactone‐grafted carbon black nanocomposites

Polycaprolactone‐grafted carbon black (CB‐g‐PCL) nanocomposites were prepared by surface‐initiated ring‐opening polymerization of ε‐caprolactone on the surface of CB. Thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), atomic force microscope (AFM), X‐ray diffraction (XRD), and polarizing optical microscope (POM) method were employed to characterize the resultant CB‐g‐PCL. The effect of temperature on resistivity of polycaprolactone‐grafted CB (CB‐g‐PCL) nanocomposites was investigated and compared with that of mixture of CB and PCL. It was found that CB‐g‐PCL nanocomposites exhibited positive temperature coefficient (PTC) phenomena between 48 and 51°C, and negative temperature coefficient (NTC) phenomena and between 51 and 54°C. The prepared CB‐g‐PCL nanocomposites have the potential to be temperature‐dependent switch materials. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

In‐depth characterization of granular starch‐graft‐polyester compositions as obtained by in situ polymerization of lactones from the starch surface

The synthesis of poly(ε‐caprolactone) (PCL)‐grafted granular starch was carried out either in bulk (without solvent) or in toluene suspension by a two‐step procedure. First step relied upon the activation of the hydroxyl groups available at the starch surface by alkylaluminum derivatives like AlEt₃ and removal of non‐surface‐grafted organo‐aluminum active species. The latter species were made free in solution by reaction with the remaining water molecules still contaminating the polymerization medium despite intensive drying of the starch granules. In the second step, ε‐caprolactone was polymerized via a coordination‐insertion ring‐opening polymerization as initiated by the surface‐grafted aluminum alkoxide species. The present contribution aims at investigating various parameters such as nature of the alkyl aluminum activator and monomer (δ‐valerolactone was studied as well), temperature, concentration, and addition of a solvent (polymerization in toluene suspension), reaction time, and also the experimental procedure used to recover the polyester chains and measure the grafting efficiency. It turns out that, under the studied conditions, dialkylaluminum alkoxides surface‐grafted onto the starch granules were more likely generated and promote a fast polymerization reaction with the formation of grafted PCL chains with a molecular weight that can be as high as 225 000 (M_n value) for polymerization carried out in toluene suspension. Copyright © 2004 Society of Chemical Industry     

Synthesis of poly(vinyl alcohol)‐graft‐poly(ε‐caprolactone) and poly(vinyl alcohol)‐graft‐poly(lactide) in melt with magnesium hydride as catalyst

Grafting of poly(ε‐caprolactone) (PCL) and poly(lactide) (PLA) chains on poly(vinyl alcohol) backbone (PVA degree of hydrolysis 99%) was investigated using MgH₂ environmental catalyst and melt‐grown ring‐opening polymerization (ROP) of ε‐caprolactone (CL) and L ‐lactide (LA), that avoiding undesirable toxic catalyst and solvent. The ability of MgH₂ as catalyst as well as yield of reaction were discussed according to various PVA/CL/MgH₂ and PVA/LA/MgH₂ ratio. PVA‐g‐PCL and PVA‐g‐PLA were characterized by ¹H‐ and ¹³C‐NMR, DSC, SEC, IR. For graft copolymers easily soluble in tetrahydrofuran (THF) or chloroform, wettability and surface energy of cast film varied in relation with the length and number of hydrophobic chains. Aqueous solution of micelle‐like particles was realized by dissolution in THF then addition of water. Critical micelle concentration (CMC) decreased with hydrophobic chains. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Physical and mechanical properties of poly(methyl methacrylate)‐grafted natural rubber synthesized by methyl methacrylate photopolymerization initiated by N,N‐diethyldithiocarbamate functions previously created on natural rubber chains

Well‐defined poly(methyl methacrylate) (PMMA)‐grafted natural rubbers (NRs) were prepared to study the structure–property relationships. Syntheses were achieved by the photopolymerization of methyl methacrylate initiated by N,N‐diethyldithiocarbamate groups created beforehand in side positions on the NR chains. With this procedure, good control of the graft density and PMMA content could be obtained. Thermal, morphological, and mechanical properties of NR‐g‐PMMA copolymers were studied as a function of the NR/PMMA composition and graft density. NR‐g‐PMMAs containing 15–80% grafted PMMA showed characteristics of heterogeneous materials (characterized by two glass‐transition temperatures, those of PMMA and NR, in differential scanning calorimetry). Under these conditions, they developed the morphology of thermoplastic elastomers with PMMA nodules dispersed in the rubber matrix when the PMMA content was near 20%; conversely, they developed the morphology of softened thermoplastics with rubber nodules dispersed in PMMA when the PMMA content was near 80%. Graft copolymers containing about 20% PMMA remained essentially rubbery, but they were already different from pure NR. On the other hand, the thermal stability of NR wash improved after the introduction of PMMA grafts onto NR chains. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Copolymers based on poly(butylene terephthalate) and polycaprolactone‐block‐polydimethylsiloxane‐block‐polycaprolactone

A series of novel thermoplastic elastomers, based on poly(butylene terephthalate) (PBT) and polycaprolactone‐block‐polydimethylsiloxane‐block‐polycaprolactone (PCL‐PDMS‐PCL), with various mass fractions, were synthesized through melt polycondensation. In the synthesis of the poly(ester‐siloxane)s, the PCL blocks served as a compatibilizer for the non‐polar PDMS blocks and the polar comonomers dimethyl terephthalate and 1,4‐butanediol. The introduction of PCL‐PDMS‐PCL soft segments resulted in an improvement of the miscibility of the reaction mixture and therefore in higher molecular weight polymers. The content of hard PBT segments in the polymer chains was varied from 10 to 80 mass%. The degree of crystallinity of the poly(ester‐siloxane)s was determined using differential scanning calorimetry and wide‐angle X‐ray scattering. The introduction of PCL‐PDMS‐PCL soft segments into the polymer main chains reduced the crystallinity of the hard segments and altered related properties such as melting temperature and storage modulus, and also modified the surface properties. The thermal stability of the poly(ester‐siloxane)s was higher than that of the PBT homopolymer. The inclusion of the siloxane prepolymer with terminal PCL into the macromolecular chains increased the molecular weight of the copolymers, the homogeneity of the samples in terms of composition and structure and the thermal stability. It also resulted in mechanical properties which could be tailored. Copyright © 2010 Society of Chemical Industry     

Synthesis and physicochemical characterization of amphiphilic block copolymer self‐aggregates formed by poly(ethylene glycol)‐block‐poly(ϵ‐caprolactone)

Diblock copolymers with different poly(ε‐caprolactone) (PCL) block lengths were synthesized by ring‐opening polymerization of ε‐caprolactone in the presence of monomethoxy poly(ethylene glycol) (mPEG‐OH, MW 2000) as initiator. The self‐aggregation behaviors and microscopic characteristics of the diblock copolymer self‐aggregates, prepared by the diafiltration method, were investigated by using ¹H NMR, dynamic light scattering (DLS), and fluorescence spectroscopy. The PEG–PCL block copolymers formed the self‐aggregate in an aqueous environment by intra‐ and/or intermolecular association between hydrophobic PCL chains. The critical aggregation concentrations of the block copolymer self‐aggregate became lower with increasing hydrophobic PCL block length. On the other hand, reverse trends of mean hydrodynamic diameters were measured by DLS owing to the increasing bulkiness of the hydrophobic chains and hydrophobic interaction between the PCL microdomains. The partition equilibrium constants (K_v) of pyrene, measured by fluorescence spectroscopy, revealed that the inner core hydrophobicity of the nanoparticles increased with increasing PCL chain length. The aggregation number of PCL chain per one hydrophobic microdomain, investigated by the fluorescence quenching method using cetylpyridinium chloride as a quencher, revealed that 4–20 block copolymer chains were needed to form a hydrophobic microdomain, depending on PCL block length. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3520–3527, 2006     

Morphological,thermal, and mechanical properties of poly(ε‐caprolactone)/poly(ε‐caprolactone)‐grafted‐cellulose nanocrystals mats produced by electrospinning

Electrospun nanocomposites of poly(ε‐caprolactone) (PCL) incorporated with PCL‐grafted cellulose nanocrystals (PCL‐g‐CNC) were produced. PCL chains were grafted from cellulose nanocrystals (CNC) surface by ring‐opening polymerization. Grafting was confirmed by infrared spectroscopy (FTIR) and thermogravimetric analyses (TGA). The resulting PCL‐g‐CNC were then incorporated into a PCL matrix at various loadings. Homogeneous nanofibers with average diameter decreasing with the addition of PCL‐g‐CNC were observed by scanning electron microscopy (SEM). PCL‐g‐CNC domains incorporated into the PCL matrix were visualized by transmission electron microscopy (TEM). Thermal and mechanical properties of the mats were analyzed by differential scanning calorimetry (DSC), TGA and dynamic mechanical analysis (DMA). The addition of PCL‐g‐CNC into the PCL matrix caused changes in the thermal behavior and crystallinity of the electrospun fibers. Significant improvements in Young's modulus and in strain at break with increasing PCL‐g‐CNC loadings were found. These results highlighted the great potential of cellulose nanocrystals as a reinforcement phase in electrospun PCL mats, which can be used as biomedical materials. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43445.     

Compatible thermoplastic starch/polyethylene blends by one‐step reactive extrusion

In the presence of dicumyl peroxide (DCP), the thermal plasticization of starch and its compatibilizing modification with polyethylene was accomplished by one‐step reactive extrusion in a single‐screw extruder at the same time. Because of the formation of polyethylene‐graft‐maleic anhydride (PE‐g‐MAH) during the extrusion, it was used as the compatibilizer between the thermoplastic starch and polyethylene. The blending samples were characterized by means of thermogravimetric analysis (TGA), scanning electron microscopy (SEM), dynamic thermal mechanical analysis (DTMA) and Fourier‐transform infrared (FTIR) analysis. The experimental results showed that in the presence of DCP the addition of MAH improved the mutual dispersion of molecules in thermoplastic starch and polyethylene. From TGA, we concluded that the thermal stability of the blends with MAH was improved compared with the blends without MAH. The DTMA and FTIR results indicated that, with the addition of MAH, the compatibility of molecules between thermoplastic starch and polyethylene in the blends was improved. Copyright © 2004 Society of Chemical Industry     

Cassava starch‐graft‐polymethacrylamide copolymers as flocculants and textile sizing agents

Cassava starch‐graft‐polymethacrylamide (PMAM) copolymers were synthesized by a free‐radical‐initiated polymerization reaction, and the products were tested for their efficiency as flocculants and textile sizing agents. The highest percentages of grafting and monomer conversion were 79.9 and 78.0%, respectively. The grafted starches were characterized by Fourier transform infrared spectroscopy, X‐ray diffraction analysis, scanning electron microscopy, differential scanning calorimetry, and thermogravimetric analysis. The average molecular weight of PMAM chains in the grafted starches ranged from 15.9 to 30.8 × 10⁵ g/mol. The grafted starches exhibited a higher peak viscosity and paste stability in comparison to the native starch (NS). Dynamic mechanical analysis showed that grafting provided fairly shear‐stable hydrogels, and the highest storage modulus obtained was 17,900 Pa compared to 1879 Pa for NS. The flocculation studies demonstrated the superiority of starch‐g‐PMAM over cassava starch and PMAM as an efficient flocculant. The tensile strength of cotton yarns sized with the starch‐grafted copolymer was significantly higher (104 MPa) compared to that sized with NS (34 MPa). © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39810.     

Effects of nano‐TiO2 on the properties and structures of starch/poly(ε‐caprolactone) composites

Poor physical properties resulting from low interfacial interactions between hydrophilic biopolymers and hydrophobic thermoplastic matrices have been one of the biggest obstacles in preparing quality biomass materials. This study concentrates on the effects of nano‐TiO₂ on the properties and structure of starch/poly (ε‐caprolactone) (PCL) composites. The molecular and crystal structures of the composites were characterized by using Fourier transform infrared spectroscopy, differential scanning calorimeter (DSC), X‐ray diffraction (XRD), and field emission scanning electron microscope. The results indicated that an interpenetrating network structure formed by adding nano‐TiO₂ into starch/PCL composites. The DSC and XRD analysis indicated that the crystallinity degree and the crystallization rate of the composites reduced, whereas the crystal form and crystal size were unchanged. The results also showed that the mechanical properties and water resistance of the composites were improved significantly with the addition of nano‐TiO₂, whereas their transparency decreased. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 4129–4136, 2013     

Property enhancement in polypropylene ternary blend nanocomposites via a novel poly(ethylene oxide)‐grafted polystyrene‐block‐poly(ethylene/butylene)‐block‐polystyrene toughener–compatibilizer system

Synthesis and characterization of a novel toughener–compatibilizer for polypropylene (PP)–montmorillonite (MMT) nanocomposites were conducted to provide enhanced mechanical and thermal properties. Poly(ethylene oxide) (PEO) blocks were synthetically grafted onto maleic anhydride‐grafted polystyrene‐block‐poly(ethylene/butylene)‐block‐polystyrene (SEBS‐g‐MA). Special attention was paid to emphasize the effect of PEO‐grafted SEBS (SEBS‐g‐PEO) against SEBS‐g‐MA on morphology, static/dynamic mechanical properties and surface hydrophilicity of the resultant blends and nanocomposites. It was found that the silicate layers of neat MMT are well separated by PEO chains chemically bonded to nonpolar SEBS polymer without needing any organophilic modification of the clay as confirmed by X‐ray diffraction and transmission electron microscopy analyses. From scanning electron microscopy analyses, elastomeric domains interacting with MMT layers via PEO sites were found to be distributed in the PP matrix with higher number and smaller sizes than the corresponding blend. As a benefit of PEO grafting, SEBS‐g‐PEO‐containing nanocomposite exhibited not only higher toughness/impact strength but also increased creep recovery, as compared to corresponding SEBS‐g‐MA‐containing nanocomposite and neat PP. The damping parameter of the same nanocomposite was also found to be high in a broad range of temperatures as another advantage of the SEBS‐g‐PEO toughener–compatibilizer. The water contact angles of the blends and nanocomposites were found to be lower than that of neat hydrophobic PP which is desirable for finishing processes such as dyeing and coating. © 2018 Society of Chemical Industry     

Structure and properties of a compatible starch‐PCL composite using p‐phthaloyl chloride‐based prepolymer

Biodegradable composites from starch and hydrophobic polymer usually show poor compatibility. A novel p‐phthaloyl chloride‐based prepolymer (PCP) compatibilizer based on p‐phthaloyl chloride and polycaprolactone (PCL) diol (2000) was synthesized successfully and the chemical structure was characterized by Fourier transform infrared spectra and ¹H nuclear magnetic resonance (NMR). The PCP compatiblizer was mixed with starch granules to form a coating layer, and then the coated starch granules were melt‐compounded with PCL plastic to prepare compatible starch‐PCL composites with enhanced properties. The structural, mechanical, thermal properties, and water absorption of the composites were then investigated. It was found that the composites containing the PCP compatibilizer showed better interfacial interaction and compatibility between starch and PCL domains compared to the pure starch‐PCL composite, which led to the improved mechanical properties of the composites. The results were attributed to the ester linkage between the PCP compatibilizer and starch as well as the strong physical crosslinking between the PCP compatibilizer and PCL plastic through PCL‐PCL crystallinity. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45400.     

Preparation and properties of thermoplastic pea starch using N,N‐bis(2‐hydroxyethyl)formamide as the plasticizer

N,N‐bis(2‐hydroxyethyl)formamide (BHF) was synthesized efficiently and used as a new plasticizer for pea starch to prepare thermoplastic starch (TPS). The hydrogen bond interaction between BHF and pea starch was proven by Fourier‐transform infrared (FT‐IR) spectroscopy. As detected by scanning electron microscope (SEM), pea starch granules were completely disrupted, and the homogeneous materials were obtained. The crystallinity of pea starch and BHF‐plasticized thermoplastic pea starch (BTPS) was characterized by X‐ray diffraction (XRD). Rheological properties of TPS were analyzed. The water resistance of BTPS was better than that of glycerol‐plasticized thermoplastic pea starch (GTPS). At RH 33%, the tensile strength of BTPS was higher than that of GTPS for TPS containing 30% plasticizer. POLYM. ENG. SCI., 2010. © 2009 Society of Plastics Engineers     

Effect of electron beam irradiation on the crystallization of silk fibroin fiber‐reinforced poly(ε‐caprolactone) biocomposites

In the medical industry, ionizing radiation has attracted increasing interest in recent years for the sterilization of biomedical materials due to its high effectiveness at relatively low cost and simple operation. In the study reported here, silk fibroin (SF) fiber was used to prepare novel reinforced poly(ε‐caprolactone) (PCL) biocomposites, and the effect of electron beam irradiation on both non‐isothermal and isothermal crystallization kinetics of the SF/PCL biocomposites was investigated. The models of Ozawa treatment, Avrami analysis and regime theory of crystal growth are applicable for describing the non‐isothermal and isothermal crystallization kinetics of the irradiated PCL and SF/PCL composites. Compared with non‐irradiated PCL and SF/PCL composites, the irradiated specimens exhibit the same crystallization regime (regime II) and similar lateral surface free energy (σ), except for smaller fold surface free energy (σ_e) and work of chain folding (q). The crosslinked PCL network formed in the irradiation process can act as a nucleation agent and accelerate the primary crystallization of PCL. However, the restriction effect of the crosslinked PCL network on the molecular chain mobility will reduce the overall crystallization rate of PCL, and this restriction effect appears stronger in the non‐isothermal crystallization process than in the isothermal crystallization process. Copyright © 2009 Society of Chemical Industry