Investigation on the melt spinning fibers of PP/organoclay nanocomposites prepared by in‐situ polymerization

Fibers prepared by melt spinning process from the PP (polypropylene)/organoclay nanocomposite were characterized in details with the aid of SEM, FTIR, XRD, DSC, and mechanical measurements. The results suggested that the lower content of organoclay (0.1%) added to the PP matrix increased the crystallinity and mechanical property (tensile strength) of the PP/organoclay nanocomposite fiber. With increasing the content of organoclay (≥ 0.3%), the crystallinity and the tensile strength both a little decreased, and the fiber containing organoclay exhibited multi‐peaks at the same draw ratio during the heating process. Furthermore, the degree of orientation of the fiber increased a little with lower content of organoclay (0.1%) introduction to PP during the infrared dichroism measurement. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Graphene‐reinforced biodegradable poly(ethylene succinate) nanocomposites prepared by in situ polymerization

In this study, poly(ethylene succinate)(PES)/graphene nanocomposites were facilely prepared by in situ melt polycondensation of succinic acid and ethylene glycol in which contained well dispersed graphene oxide (GO). Fourier transform infrared (FTIR), GPC, TGA, and XRD were used to characterize the composites. The FTIR spectra and TGA measurement confirmed that PES chains had been successfully grafted onto GO sheets along with the thermal reduction of GO to graphene during the polymerization. GPC results indicated that increasing amounts of graphene caused a slight decrease in number average molecular weight of PES matrix when polymerization time was kept constant. The content of grafted PES chains on graphene sheets was also determined by TGA and was to be about 60%, which made the graphene sheets homogeneously dispersed in the PES matrix, as demonstrated by SEM and XRD investigations. Furthermore, the incorporation of thermally reduced graphene improved the thermal stability and mechanical properties of the composites significantly. With the addition of 0.5 wt % graphene, onset decomposition temperature of the composite was increased by 12°C, and a 45% improvement in tensile strength and 60% in elongation at break were also achieved. The enhanced performance of the composites is mainly attributed to the uniform dispersion of graphene in the polymer matrix and the improved interfacial interactions between both components. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3212–3220, 2013     

Preparation and properties of polyethylene/montmorillonite nanocomposites by in situ polymerization

Polyethylene (PE)/montmorillonite (MMT) nanocomposites were prepared by in situ coordination polymerization using a MMT/MgCl₂/TiCl₄ catalyst activated by Al(Et)₃. The catalyst was prepared by first diffusing MgCl₂ into the swollen MMT layers, followed by loading TiCl₄ on the inner/outer layer surfaces of MMT where MgCl₂ was already deposited. The intercalation of MMT layers by MgCl₂ and TiCl₄ was demonstrated by the enlarged interlayer spacing determined by WAXD. The nanoscale dispersion of MMT layers in the polyethylene matrix was characterized by WAXD and TEM. As a consequence, the crystallinity of the nanocomposite decreased sharply, whereas the tensile strength was significantly improved compared to that of virgin polyethylene of comparable molecular weight. The confinement of the nanodispersed MMT layers to molecular chain and the strong interaction between the nanoscale MMT layers and the resin matrix were thought to account for the decrease of crystallinity and the remarkable enhancement of strength. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3680–3684, 2003     

Polyamide 6/silica nanocomposites prepared by in situ polymerization

A polyamide 6 (PA 6)/silica nanocomposite was obtained through a novel method, in situ polymerization, by first suspending silica particles in ϵ-caproamide under stirring and then polymerizing this mixture at high temperature under a nitrogen atmosphere. The silicas were premodified with aminobutyric acid prior to the polymerization. The effects of the addition of unmodified and modified silicas on the dispersion, interfacial adhesion, isothermal crystallization, and mechanical properties of PA 6 nanocomposites were investigated by using scanning electron microscopy, dynamic mechanical analysis, differential scanning calorimetry, and mechanical tests, respectively. The results show that the silicas dispersed homogeneously in the PA 6 matrix. The addition of silicas increases the glass transition temperature and crystallization rate of PA 6. The mechanical properties such as impact strength, tensile strength, and elongation at break of the PA 6/modified silica nanocomposites showed a tendency to increase and decrease with increase of the silica content and have maximum values at 5% silica content, whereas those of the PA 6/unmodified silica system decreased gradually. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 355–361, 1998     

Preparation and crystallization of poly(ethylene terephthalate)/SiO2 nanocomposites by in‐situ polymerization

Poly(ethylene terephthalate) (PET)/SiO₂ nanocomposites were prepared by in situ polymerization. The dispersion and crystallization behaviors of PET/SiO₂ nanocomposites were characterized by means of transmission electron microscope (TEM), differential scanning calorimeter (DSC), and polarizing light microscope (PLM). TEM measurements show that SiO₂ nanoparticles were well dispersed in the PET matrix at a size of 10–20 nm. The results of DSC and PLM, such as melt‐crystalline temperature, half‐time of crystallization and crystallization kinetic constant, suggest that SiO₂ nanoparticles exhibited strong nucleating effects. It was found that SiO₂ nanoparticles could effectively promote the nucleation and crystallization of PET, which may be due to reducing the specific surface free energy for nuclei formation during crystallization and consequently increase the crystallization rate. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 655–662, 2006     

Studies on electro‐conductive yarns prepared by in situ chemical and electrochemical polymerization of pyrrole

This work deals with preparation, characterization, and performance of electro‐conductive yarns prepared by in situ chemical and electrochemical polymerization of pyrrole. Box‐Behnken design in conjunction with response surface analysis has been used to study the electrochemical polymerization process. The effect of electrochemical process parameters on the electrical resistivity has been reported. Further, the electrical and electromechanical behaviour of the electro‐conductive yarns thus produced has also been reported. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Intercalation structure and toughening mechanism of graphene/urea‐formaldehyde nanocomposites prepared via in situ polymerization

Based on the industrialized graphene (GN) product, a series of graphene/urea‐formaldehyde nanocomposites were synthesized via in situ polymerization by incorporation of silicon coupling agent with terminal amino groups (SA) as the compatibilizer. The results showed that addition of SA coupling agent led to much more efficient grafting of UF molecules on the GN surface with high layer thickness by formation of hydrogen bonding, and thus complete exfoliation and uniform dispersion of GN were achieved for the composites. Compared with neat UF, the addition of 1.0 wt% GN resulted in a roughly 25% increase in tensile strength and 12% increase in impact strength; meanwhile the impact fracture surfaces of the composite showed obvious ductile fracture characteristics, indicating the reinforcing and toughening effect of GN on the UF matrix. With increasing GN content, the storage modulus, glass transition temperature and crosslinking density of UF increased, while the tan δ_max decreased, suggesting that a double crosslinking network structure with GN centered crosslinking point and chemical crosslinking point of UF molecular chains formed, leading to improvement in the stiffness of the composites. The present work showed promising potential for developing high performance UF resin on an industrial scale. © 2017 Society of Chemical Industry     

Preparation and characterization of polypropylene–montmorillonite nanocomposites generated by in situ metallocene catalyst polymerization

An ion‐exchange method was applied to replace sodium cations inside the interlamellar space of montmorillonite with positively charged stearyl trimethyl ammonium chloride. The d₀₀₁‐spacing of montmorillonite is larger in toluene than in other solvents. The overexchanged stearyl methyl ammonium chloride in the montmorillonite layers can be completely washed out by ethanol. Polypropylene–montmorillonite nanocomposites were prepared by using the supported rac‐Et(Ind)₂ZrCl₂ catalyst on the montmorillonite. The nanocomposites that were polymerized by the supported catalyst were characterized by infrared spectroscopy, nuclear magnetic resonance, X‐ray diffraction, differential scanning calorimetry, scanning electron microscopy, and transmission electron microscopy. Transmission electron microcopy shows that each silicate sheet of montmorillonite is randomly dispersed into the polypropylene matrix following polymerization by using a supported catalyst. The polypropylene nanocomposites had higher crystallinity, hardness, and thermal properties than pure polypropylene. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1228–1236, 2005     

Synthesis and characterization of chlorine‐containing flame‐retardant polyurethane nanocomposites via in situ polymerization

We have developed flame‐retardant polyurethanes (FRPUs) and polyurethane (PU) nanocomposites via in situ polymerization. Three series of thermoplastic elastomeric PUs were synthesized to investigate the effect of incorporating 3‐chloro‐1,2‐propanediol (CPD) and nanoclay on mechanical, thermal properties, and also resistance to burning. PU soft segments were based on poly(propylene glycol). Hard segments were based on either CPD or 1,4‐buthane diol (BDO) in combination with methyl phenyl di‐isocyanate named PU or FRPU, respectively. In the third series, CPD was used as chain extender also nanoclay (1% wt) and incorporated and named as flame‐retardant polyurethane nanocomposites (FRPUN). Mechanical properties and LOI of PUs and nanocomposites have been evaluated. Results showed that increasing the hard segment (chlorine content) leads to the increase in flame retardancy and burning time. Addition of nanoclay to CPD‐containing PUs leads to obtain self‐extinguish PUs using lower CPD contents, higher Young's modulus, and strength without any noticeable decrease in elongation at break. Investigation of the TGA results showed that copresence of nanoclay and chlorine structure in the PU backbone can change thermal degradation pattern and improve nanocomposite thermal stability. X‐ray diffraction and transmission electron microscopy studies confirmed that exfoliation and intercalation have been well done. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and crystallization behavior of acetal copolymer/silica nanocomposite by in situ cationic ring‐opening copolymerization of trioxane and 1,3‐dioxolane

The acetal copolymer/silica nanocomposite was prepared by in situ bulk cationic copolymerization of trioxane and 1,3‐dioxolane in the presence of nanosilica. The crystallization behavior of acetal copolymer/silica nanocomposite was studied by AFM, DSC, XRD, and CPOM, and the macromolecular structure of acetal copolymer/silica nanocomposite was characterized by FTIR and ¹H‐NMR. The ¹H‐NMR results showed that the macromolecular chain of acetal copolymer had more than two consecutive 1,3‐dioxolane units in an oxymethylene main chain, while that of acetal copolymer/silica nanocomposite had only one 1,3‐dioxolane unit in an oxymethylene main chain. There existed interaction between the macromolecular chains and nanoparticles (such as hydrogen bonds and coordination). On one hand, nanoparticles acted as nucleation center, which accelerated the crystallization rate but reduced the crystallinity. The spherulite sizes also decreased with addition of nanoparticles attributed to the nucleation effect. On the other hand, the presence of nanoparticles interrupted the spherical symmetry of the crystallite. In conclusion, the high surface energy and small scale of nanoparticles have a prominent impact on the polymerization mechanism and crystallization behavior of nanocomposite. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and characterization of polyurethane/montmorillonite nanocomposites by in situ polymerization

In this paper, a new type of organophilic montmorillonite, co‐treated with cetyltrimethyl ammonium bromide (CTAB) and 4,4′‐diphenymethylate diisocyanate (MDI), was modified and applied to prepare polyurethane/montmorillonite nanocomposites via in situ polymerization. The nanoscale montmorillonite layers were exfoliated and dispersed relatively homogeneously in the polyurethane matrix, and characterized by X‐ray diffraction and transmission electron microscopy. The thermal degradation temperature of the nanocomposites increased, as compared with pristine polyurethane. Dynamic mechanical analysis confirmed the constraining effect of exfoliated montmorillonite layers on polyurethane chains, which benefited the increased storage modulus and increased glass transition temperature. Tensile tests showed that the exfoliated nanocomposites were reinforced and toughened by the addition of nanometer‐size montmorillonite layers. Copyright © 2006 Society of Chemical Industry     

Preparation of silica/polyurethane nanocomposites by UV‐induced polymerization from surfaces of silica

UV‐curable nanocomposites were prepared by the in situ photopolymerizaton with nanosilica obtained from sol–gel process. The photoinitiator 2‐hydroxy‐2‐methyl‐1‐phenylpropane‐1‐one (1173) was anchored onto the surface of the nanosilica with or without methacryloxypropyltrimethoxysilane (MAPS) modification. The photopolymerization kinetics was studied by real‐time Fourier transform IR (RTIR), and the microstructure and properties of the nanocomposite were investigated using transmission electron microscopy and UV–visible (UV–vis) transmistance spectra. RTIR analysis indicated that the nanocomposites without MAPS had higher curing rates and final conversion than those with MAPS. The nanocomposites with an uniformal dispersion of nanosilica had high UV–vis transmittance. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Crystallization behavior of poly(p‐dioxanone)‐PU/montmorillonite nanocomposites prepared by chain‐extending reaction

Organo‐modified montmorillonites and poly(p‐dioxanone) (PPDO) diol prepolymers were used to prepare Poly(p‐dioxanone)‐PU/organic montmorillonite (PPDO‐PU/OMMT) nanocomposites by chain‐extending reaction. The crystallization behavior and spherulitic morphology of PPDO‐PU/OMMT nanocomposites were investigated by WXRD, differential scanning calorimetry, and polarized optical microscopy. The results show that the regularity of the chain structure plays a dominant role during the crystallization process rather than that of OMMT content and its dispersion status in PPDO matrix. With similar molecular weight and same OMMT content, PPDO‐PU/OMMT nanocomposite, which derived from lower molecular weight PPDO prepolymer, exhibits lower crystallization rate, melting point, and crystallinity. The influence of the clay content on the crystallization behavior highly depends on its dispersing state. The nucleating effect of OMMT can be only observed at high loading percentage. For the nanocomposites with low clay loading percentage, the retarding effect of exfoliated platelets on the chain‐ordering into crystal lamellae became the key factor. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Crystallization behavior of ultrahigh‐molecular‐weight polyethylene/polyhedral oligomeric silsesquioxane nanocomposites prepared by ethylene in situ polymerization

A [3‐t‐Bu‐2‐O? C₆H₃CH?N(C₆F₅)]₂TiCl₂ catalyst (bis(phenoxyimine)titanium dichloride complex – FI catalyst) was immobilized on disilanolisobutyl polyhedral oligomeric silsesquioxane (OH‐POSS) to prepare ultrahigh molecular‐weight polyethylene (UHMWPE)/polyhedral oligomeric silsesquioxane (POSS) nanocomposites during ethylene in situ polymerization. The dispersion state of POSS in the UHMWPE matrix was characterized by X‐ray diffraction measurements and transmission electron microscopy. It was shown that the OH‐POSS achieved uniformed dispersion in the UHMWPE matrix, although its polarity was unmatched. The isothermal and nonisothermal crystallization behavior of the nanocomposites was investigated by means of differential scanning calorimetry. The crystallization rate of the nanocomposites was enhanced because of the incorporation of POSS during the isothermal crystallization. POSS acted as a nucleus for the initial nucleation and the subsequent growth of the crystallites. For nonisothermal studies, POSS showed an increase in the crystallinity. The crystallization rate of the nanocomposites decreased because the presence of POSS hindered the crystal growth. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40847.     

Synthesis and properties of homogeneously dispersed polyamide 6/MWNTs nanocomposites via simultaneous in situ anionic ring‐opening polymerization and compatibilization

Toluene 2, 4‐diisocyanate (TDI) functionalized multiwalled carbon nanotubes (MWNTs‐NCO) were used to prepare monomer casting polyamide 6 (MCPA6)/MWNTs nanocomposites via in situ anionic ring‐opening polymerization (AROP). Isocyanate groups of MWNTs‐NCO could serve as AROP activators of ?‐caprolactam (CL) in the in situ polymerization. Fourier transform infrared (FTIR) showed that a graft copolymer of PA6 and MWNTs was formed in the in situ polymerization. MWNTs‐PA6 covalent bonds of the graft copolymer constituted a strong type of interfacial interaction in the nanocomposites and increased the compatibility of MWNTs and MCPA6 matrix. The nanocomposites were characterized for the morphology, mechanical, crystallization, and thermal properties through field emission transmission electron microscopy (FETEM), tensile testing, differential scanning calorimeter (DSC), and thermogravimetric analysis (TGA). FETEM analysis showed that MWNTs were homogeneously dispersed in MCPA6 matrix. The initial tensile strengths and tensile modulus of the nanocomposite with 1.5 wt % loading of MWNTs were enhanced by about 16 and 13%, respectively, compared with the corresponding values for neat MCPA6. DSC analysis indicated that the crystallization temperature of the nanocomposites was increased by 8°C by adding 1.5 wt % MWNTs compared with pure MCPA6. Besides, it was found that the thermal stability of MCPA6 was improved by the addition of the MWNTs. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Polyethylene nanocomposites by gas‐phase polymerization of ethylene in the presence of a nanosilica‐supported zirconocene catalyst system

BACKGROUND: Much of the current research related to the development of in situ nanocomposites of olefins by polymerizing them with metallocenes in the presence of surface‐treated fillers is carried out in the slurry phase. In slurry‐phase methods a large amount of solvent is required and there is always a need of purification of the final product due to the possibility of traces of solvents present in the product. To overcome these drawbacks, to perform solvent‐free metallocene‐catalysed polymerizations with in situ incorporation of inorganic nanoparticles, we have used a gas‐phase polymerization technique as this does not require solvents and also utilizes monomer feed stocks efficiently. RESULTS: The catalyst used for the synthesis of in situ polyethylene nanocomposites by gas‐phase polymerization was nanosilica‐supported zirconocene. The fillers used were Cloisite‐20A, kaolin and nanosilica. Three different in situ polyethylene nanocomposites, i.e. Cloisite‐20A‐filled polyethylene (CFPE), kaolin‐filled polyethylene (KFPE) and nanosilica‐filled polyethylene (SFPE), were prepared by gas‐phase polymerization. The nanocomposites were obtained in the form of fine powder. The polyethylene content in the developed nanocomposites is in the orthorhombic crystalline phase. Using our approach, it is observed that the nanofillers are completely encapsulated by a thin layer of polyethylene. Significantly higher molecular weight polyethylene was formed in the case of KFPE in comparison to CFPE and SFPE. The thermal decomposition temperature, melting temperature and enthalpy are also observed to be higher for KFPE. CONCLUSIONS: The gas‐phase polymerization technique has been successfully carried out for the synthesis of in situ polyethylene nanocomposites. Copyright © 2007 Society of Chemical Industry     

Highly exfoliated poly(ϵ‐caprolactone)/organomontmorillonite nanocomposites prepared by in situ polymerization

Ethylene–propylene–diene rubbers (EPDM) with 2-ethylidene-5-norbornene (ENB), dicyclopentadiene (DCPD), and 1,4-hexadiene (HD) as third monomers have been vulcanized with peroxide and with a conventional sulfur vulcanization recipe, and their devulcanization was subsequently investigated for recycling purposes. The behavior of these vulcanizates during pure thermal devulcanization depends on the EPDM third monomer and the crosslinker used. Peroxide vulcanizates of ENB-EPDM devulcanize only to a small extent and predominantly by random scission, whereas peroxide vulcanizates of HD-EPDM devulcanize by crosslink scission. In contrast, sulfur vulcanizates of ENB-EPDM, devulcanize mainly by crosslink scission. During devulcanization of sulfur-cured HD-EPDM, scission of both crosslinks and main chains occurs. Sulfur-cured DCPD-EPDM cannot be devulcanized but shows further crosslinking instead. In those cases, where purely thermal devulcanization is already effective to a certain extent, diphenyldisulfide as devulcanization agent increases the effectivity during thermochemical devulcanization. Hexadecylamine as an alternative devulcanization agent is effective for ENB-EPDM but does not contribute to thermochemical devulcanization of HD-EPDM. In summary, devulcanization proceeds by different mechanisms in ENB-EPDM, DCPD-EPDM, and HD-EPDM. Explanations are given in terms of the chemical structures of the third monomers, the corresponding crosslinks, and devulcanization agents. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Structure and properties of polybutadiene/montmorillonite nanocomposites prepared by in situ polymerization

Polybutadiene (PB)/Montmorillonite nanocomposites (NCs) were prepared by in situ polymerization through the anionic polymerization technique. The effects of treating method of organophilic MMT (OMMT), the type of OMMT, and the solvent used in polymerization were studied. The structure and properties of NCs were characterized using X‐ray Diffraction (XRD), transmission electron micrograph (TEM), H‐NMR spectrum, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and dynamic mechanical analysis (DMA). The consumption of BuLi was varied with different treating methods. The molecular weight distribution of PB added with OMMT (DK1) was wide, and the molecular weight distribution became narrow when OMMT‐DK1B and DK4 were added. OMMT did not disperse stably in cyclohexane, but could form a homogeneous solution in toluene and xylene. XRD and TEM showed that exfoliated NCs were obtained by in situ polymerization through the anionic polymerization technique. From the H‐NMR spectrum of PB and PB/OMMT NCs, it could be seen that the content of 1, 2 units of PB increased ～100%, while 1, 4 units decreased when 6.2 wt % of OMMT was added. The results of DSC and DMA indicated that T_g and T_dc were increased when compared with those of PB. Both storage modulus and loss modulus were increased with the addition of OMMT, and tan δ was decreased. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3615–3621, 2006     

Experimental studies on electro‐conductive fabric prepared by in situ polymerization of thiophene onto polyester

This work deals with development, characterization, and performance of an electro‐conductive fabric prepared by in situ polymerization of thiophene onto polyester. An attempt was made to optimize the polymerization process to achieve highest level of electro‐conductivity of this fabric. The essential characteristics of this electro‐conductive fabric were examined and its electromagnetic shielding performance was evaluated. Polythiophene powder was also synthesized and analyzed. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Isotactic polypropylene metal oxide and silica nanocomposites by a two‐step process comprising in situ olefin polymerization and melt compounding

Nanocomposites of isotactic polypropylene (iPP) with 0.5 wt% filler of MgO@Mg(OH)₂ (35 nm) or silicon dioxide (20–60 nm) or barium titanate (50 nm) nanoparticles were obtained from melt compounding of filler masterbatches with commercial iPP. The masterbatches with 5 wt% nanofiller were prepared in an in situ polymerization procedure using a metallocene/methylaluminoxane (MAO) catalyst system that was supported on the respective oxides. The original agglomerates of the nanoparticles were broken up by treatment with dibutylmagnesium for MgO@Mg(OH)₂, and with ultrasound in the presence of MAO for SiO₂ and BaTiO₃. The tacticity (98% mmmm) of the in situ formed PP was not influenced by the presence of the nanofillers. Scanning electron microscopy and energy‐dispersive X‐ray spectroscopy mapping show a fine dispersion of single particles and small clouds or clusters. The primary nanoparticles appear to be surrounded by polymer. The elongation at break was decreased to 50, 17 and 9% for MgO@Mg(OH)₂), SiO₂ and BaTiO₃, respectively. After melt compounding with iPP, a homogeneous single‐particle distribution of the oxidic nanoparticles was found in the resulting composites with 0.5 wt% filler content. © 2019 Society of Chemical Industry