Tensile and elastic properties of triblock copolymer based on aramide end‐segments and polyether mid‐segments

The tensile and elastic behavior of triblock copolymers containing uniform aramide (TΦB) hard end‐segments (HS) and poly(tetramethylene oxide) (PTMO, M_n = 2900 g/mol) soft segments (SSs) was studied. The molecular weight of the copolymer was varied by changing the length of the soft mid‐segment; by extending the PTMO₂₉₀₀ with terephthalate units, the SS length was increased from 2900 g/mol to 21,000 g/mol and concurrently the aramide concentration decreased from 18 to 3 wt %. The mechanical properties were investigated by means of tensile testing, stress relaxation (SR) experiments, and cyclic tensile set (TS) tests. The E‐modulus was found to increase with increasing aramide content. The low molecular weight copolymers were brittle whereas the high molecular weight copolymers displayed large fracture strain values. The transition from brittle to ductile seemed to occur at a triblock copolymer molecular weight of 6600 g/mol. A strain‐induced crystallization was observed at strains above 250%, and both the fracture strain and stress were found to be highly dependant on the molecular weight of the copolymer. Cyclic tensile experiments showed that the materials had low TS values up to the strain hardening point. On the other hand, the SR data at 10% strain seemed to be little dependant on the molecular weight. The higher molecular weight copolymers did not display lower SR values than their low molecular weight counterparts. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Differential scanning calorimetry analysis of silicon‐containing and phosphorus‐containing segmented polyurethane. I—Thermal behaviors and morphology

This article investigated thermal transition and morphology utilizing differential scanning calorimetry (DSC), which was performed on silicon‐containing and phosphorus‐containing segmented polyurethane (Si‐PU and P‐PU). The hard segments of those Si‐PU and P‐PU polymers investigated consisted of 4,4′‐diphenylmethane diisocyanate (MDI) and diphenylsilanediol (DSiD), MDI, and methylphosponic (MPA), respectively. The soft segment of those polymers comprised polytetramethylene ether glycol, with an average molecular weight of 1000 or 2000 (PTMG 1000 and PTMG 2000, respectively). Several thermal transitions appeared for on the Si‐PU and P‐PU polymers, reflecting both the soft‐segment and hard‐segment phases. The Si‐PU and P‐PU polymers with a lower hard‐segment content exhibited a high degree of phase separating as indicated by the constancy of both the soft‐segment glass transition temperature (T_gs) and the breadth of transition zone (ΔB). The polymers in which PTMG 2000 was used as the soft segment generally exhibited a crystalline melting endotherm about 10°C, while crystallization usually disappeared upon melt quenching. The hard segments of the Si‐PU and P‐PU polymers displayed multiple endotherms. The first endotherm was related to a short‐range ordering of the hard segment domain (Region I), and the second endotherm was ascribed to a long‐range ordering of the domain (Region II). The wide‐angle X‐ray demonstrated that the structure in Region I and Region II was almost completely amorphous. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 3489–3501, 2001     

Effect of filler content on the structure‐property behavior of poly(ethylene oxide) based polyurethaneurea‐silica nanocomposites

Poly(ethylene oxide) (PEO) based polyurethaneurea‐silica nanocomposites were prepared by solution blending and characterized by Fourier Transform Infrared Spectroscopy, Scanning Electron Microscopy, Differential Scanning Calorimetry and tensile testing. The colloidal silica nanoparticles with an average size of 50 nm were synthesized by modified Stöber method in isopropanol. Silica particles were incorporated into three cycloaliphatic polyurethaneurea (PUs) copolymers based on PEO oligomers with molecular weights of 2,000, 4,600, and 8,000 g/mol. Hard segment content of PUs was constant at 30% by weight. Silica content of the PU nanocomposites varied between 1 and 20% by weight. Soft segment (SS) glass transition and melting temperatures slightly increased with increasing filler content for all the copolymers. Degree of SS crystallinity first increased with 1% silica incorporation and subsequently decreased by further silica addition. Elastic modulus and tensile strengths of PU copolymers gradually increased with increasing amount of the silica filler. Elongation at break values gradually decreased in PEO‐2000 based PU copolymer with increasing silica content, whereas no significant change was observed in PUs based on PEO‐4600 and PEO‐8000. Enhancement in tensile properties of the materials was mainly attributed to the homogeneous distribution of silica filler in polymer matrices and strong polymer‐filler interactions. POLYM. ENG. SCI., 58:1097–1107, 2018. © 2017 Society of Plastics Engineers     

Effects of organophilic‐modified attapulgite nanorods on thermal and mechanical behavior of segmented polyurethane elastomers

The effects of different grafting content of 4,4′‐methlenebis(phenyl isocyanate)‐modified attapulgite (ATT‐MDI) on thermal and mechanical properties of segmented polyurethane (PU) elastomers were investigated. The ATT‐MDI nanorods with different grafting content were prepared by treating ATT with heat and acid followed by grafting with MDI molecules. MDI‐modified ATT were characterized by transmission electron microscopy (TEM), thermogravimetric analysis (TGA), and Fourier transform infrared spectroscopy. TGA analysis revealed that at least 30 wt % of MDI was grafted/adsorbed on the surface of ATT following the modification. Three PU/ATT‐MDI nanocomposites were in situ synthesized using ATT with different grafting contents, and the materials were characterized by TEM, thermal analysis, and mechanical testing. The tensile strength and modulus increased with increasing grafting content of MDI molecules, and the crystallinity of soft and hard segments was increased by ATT‐MDI. POLYM. COMPOS., 31:1890–1898, 2010. © 2010 Society of Plastics Engineers.     

Effective preparation and characterization of montmorillonite/poly(ε‐caprolactone)‐based polyurethane nanocomposites

In this study, montmorillonite (MMT)/poly(?‐caprolactone)‐based polyurethane cationomer (MMT/PCL‐PUC) nanocomposites were prepared and their mechanical properties, thermal stability, and biodegradability were investigated. PCL‐PUC has 3 mol % of quaternary ammonium groups in the main chain. The MMT was successfully exfoliated and well dispersed in the PCL‐PUC matrix for up to 7 wt % of MMT. The 3 mol % of quaternary ammonium groups facilitated exfoliation of MMT. The 1 wt % MMT/PCL‐PUC nanocomposites showed enhanced tensile properties relative to the pure PCL‐PU. As the MMT content increased in the MMT/PCL‐PUC nanocomposites, the degree of microphase separation of PCL‐PUC decreased because of the strong interactions between the PCL‐PUC chains and the exfoliated MMT layers. This resulted in an increase in the Young's modulus and a decrease in the elongation at break and maximum stress of the MMT/PCL‐PUC nanocomposites. Biodegradability of the MMT/PCL‐PUC nanocomposites was dramatically increased with increasing content of MMT, likely because of the less phase‐separated morphology of MMT/PCL‐PUC. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

The mechanical/thermal properties of microcellular injection‐molded poly‐lactic‐acid nanocomposites

This study investigated the influence of montmorillonite (MMT) content on the mechanical/thermal properties of microcellular injection‐molded polylactide (PLA)/clay nanocomposites. Carbon dioxide was the blowing agent. The PLA/MMT nanocomposites were prepared by twin screw extrusion. The results showed that as MMT content is increased, tensile strength, impact strength, and cell density decrease. This is caused by the speed degradation of PLA due to the addition of MMT. MMT decreases the crystallization temperature but increases the decomposition temperature of the nanocomposites. The XRD results showed that the layer spacing of the clay increases as MMT content increases. TEM pictures showed that the MMT is well dispersed within the PLA matrix. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers.     

Surface‐modifiers of clay on mechanical properties of rigid polyurethane foams/organoclay nanocomposites

Three different surface modifiers, octadecyl trimethyl ammonium (ODTMA), octadecyl primary ammonium (ODPA), and decanediamine (DDA) were used to modify Na⁺? montmorillonite (MMT), and the resultant organoclays were coded as ODTMA‐MMT, ODPA‐MMT, DDA‐MMT, respectively. Rigid PU foams/organoclay composites were prepared by directly using organoclay as the blowing agent without the addition of water. Investigation shows that the morphology of the nanocomposites is greatly dependent on the surface modifiers of clay used in the composites. In detail, DDA‐MMT is partially exfoliated in the PU matrix with the smallest cell size, while two others are intercalated in the PU matrices with smaller cell sizes. The sequence of their cell sizes is pristine PU foams > rigid PU foams/ODTMA‐MMT > rigid PU foams/ODPA‐MMT > rigid PU foams/DDA‐MMT, and the average cell size of rigid PU foams/DDA‐MMT composites decreases evidently from 0.30 to 0.07 mm. Moreover, all rigid PU foams/organoclay composites show remarkable enhanced compressive and tensile strengths as well as dynamic properties than those of PU foams, and the enhancement degree coincides well with the relative extent of internal hydrogen bonding of materials and gallery spacing of organoclay. For example, in the case of rigid PU foams/DDA‐MMT composite, 214% increase in compressive strength and 148% increase in tensile strength compared with those of pure PU foams were observed. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Effect of oligomeric‐modified montmorillonite on morphology and properties of polycarbonate/montmorillonite nanocomposites

Low‐molecular‐weight copolymers of styrene and vinylbenzyl ammonium salts (oligomeric surfactant) were used to modify montmorillonite (MMT). The oligomeric‐modified MMT showed good thermal stability, which made it suitable to be used for preparing polycarbonate(PC)/MMT nanocomposites at high temperature. A different series of PC/MMT nanocomposites had been prepared by melt processing using a twin screw extruder. The effect of oligomeric surfactant structure and clay loading on the morphology, mechanical property, thermal stability, and color appearance of the nanocomposites were explored. The results of X‐ray diffraction and transmission electron microscopy analyses indicated that the PC/MMT nanocomposites had partially exfoliated structures. The PC/MMT nanocomposites were found to retain light colored, which was important for optical application. Compared to neat PC, the nanocomposites showed better properties of thermal stability and heat insulation. The mechanical properties of the nanocomposites are significantly enhanced by incorporating clay into the PC matrix. The tensile strength of nanocomposites with 2 wt% clay content was up to 55 MPa, which was much higher than that of the neat PC (37 MPa). The maximum tensile modulus value was 19% higher than that of neat PC. POLYM. COMPOS., 2013. © 2013 Society of Plastics Engineers     

Aliphatic polycarbonate‐based polyurethane elastomers and nanocomposites. I. The influence of hard‐segment content and macrodiol‐constitution on bottom‐up self‐assembly

Aliphatic polycarbonate‐based polyurethane (PC‐PU) elastomers as well as their nanocomposites with organic‐modified clay (bentonite for organic system) were synthesized. Macrodiols (MD) (randomly copolymerized aliphatic PC‐glycols of molecular weight of about 2000: T5652, T4672, and T4692), hexamethylene diisocyanate, and butane‐1,4‐diol were used as starting materials. Solid‐state NMR and Fourier transform infrared spectroscopy, small‐angle X‐ray scattering, wide‐angle X‐ray diffraction, atomic force microscopy, and transmission electron microscopy were used for studying the bottom‐up self‐assembly of building units from the segmental level up that of organized structures of micrometer sizes. Contents of hard segments formed by the reaction of chain extender with diisocyanate plays a dominant role for the degree of ordering and related phenomena, while the MD chain has only limited effect on PC‐PU properties. The spectroscopy and scattering experiments suggest that bentonite particles incorporate well in the structure and promote the ordering of hard segment domains in PC‐PU matrix as compared with the nanofiller‐free analogue. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

纳米蒙脱土-脂肪族聚氨酯弹性体的合成与制备

采用聚四氢呋喃醚（PTMG1000）为软段,4,4’-二环己基甲烷二异氰酸酯（HMD1）、异佛尔酮二异氰酸酯（1PD1）为硬段,层间距分别为1．95nm和2．40nm的2种有机蒙脱土,以插层聚合法制备出不同硬段含量和有机蒙脱土含量的纳米蒙脱土．脂肪族聚氨酯弹性体,并研究了硬段含量、有机蒙脱土含量、二异氰酸酯和有机蒙脱土种类对脂肪族聚氨酯弹性体力学性能的影响。结果表明,硬段含量对材料力学性能影响最大,其次是有机蒙脱土含量。当硬段质量分数达40％时,拉伸强度最高达14．06MPa;有机蒙脱土少量加入可有效提高材料的撕裂强度和断裂伸长率。以HMD1、PTMG1000和MMT2为原料,硬段质量分数为40％时,所合成的纳米蒙脱土-脂肪族聚氨酯弹性体具有较好的力学性能。     

TIPA/BDO扩链的聚氨酯弹性体力学性能的研究

以聚酯(PEA、PEPA)或聚醚(PTMG)和TDI为原料合成聚氨酯(PU)预聚体,用三异丙醇胺(TIPA)和1,4-丁二醇(BDO)的混合物作扩链剂制备PU弹性体。讨论了软段相对分子质量、弹性体交联点相对分子质量和扩链剂的种类对PU弹性体性能的影响。结果表明,PU弹性体的硬度、拉伸强度、300%模量和撕裂强度随软段相对分子质量的增加而下降,而伸长率和冲击弹性随软段相对分子质量的增加而增加;交联点相对分子质量为6600时,PTMG2000为软段的PU弹性体的拉伸强度最高,达到28.44MPa;与TMP/BDO扩链的聚酯型PU弹性体相比,TIPA/BDO扩链的弹性体的拉伸强度、伸长率和撕裂强度均较高,而硬度、300%模量和冲击弹性差异不大。     

Morphology and properties of stearate‐intercalated layered double hydroxide nanoplatelet‐reinforced thermoplastic polyurethane

In the past few years, layered double hydroxides (LDHs) with monolayer structure have been much studied for the development of polymer nanocomposites. LDHs with intercalated stearate anions form a bilayer structure with increased interlayer spacing and are expected to be better nanofillers in polymers. In the work reported, thermoplastic polyurethane (PU)/stearate‐intercalated LDH nanocomposites were prepared by solution intercalation and characterized. X‐ray diffraction and transmission electron microscopy confirmed the exfoliation at lower filler loading followed by intercalation at higher filler loading in PU matrix. As regards mechanical properties, these nanocomposites showed maximum improvements in tensile strength (45%) and elongation at break (53%) at 1 and 3 wt% loadings. Maximum improvements in storage and loss moduli (20%) with a shift of glass transition temperature (15 °C) and an increase in thermal stability (32 °C) at 50% weight loss were observed at 8 wt% loading in PU. Differential scanning calorimetry showed a shift of melting temperature of the soft segment in the nanocomposites compared to neat PU, possibly due to the nucleating effect of stearate‐intercalated LDH on the crystal structure of PU. All these findings are promising for the development of mechanically improved, thermally stable novel PU nanocomposites. Copyright © 2011 Society of Chemical Industry     

Morphology,mechanical property,and processing thermal stability of PVC/La‐OMMTs nanocomposites prepared via in situ intercalative polymerization

Poly(vinyl chloride) (PVC) nanocomposites were prepared via an in situ intercalative suspension polymerization of vinyl chloride with four organic carboxylic acid salts (montmorillonite [MMT] units) containing thermally stable lanthanum ions. The effects of different lanthanum organic montmorillonites (La‐OMMTs) on the particle features and molecular weight were investigated. The transmission electron microscopy data indicated the formation of partially exfoliated or intercalated PVC/La‐OMMTs nanocomposites. The effect of different functional groups on the mechanical properties and processing thermal stability of PVC/La‐OMMT nanocomposites were investigated. Tensile testing and two‐roll mill processing results showed that La‐OMMTs could enhance the dynamic thermal stability and mechanical properties versus PVC pure resin and PVC/I.30P nanocomposites (composed of PVC and I.30P). This suggested that the double bond and amidogen group in La‐OMMTs could promote the dispersion of La‐OMMTs in the PVC matrix and also improve the adhesion between the La‐OMMTs and PVC matrix. The results have potential value in the industrial development of PVC/La‐OMMTs nanocomposites. J. VINYL ADDIT. TECHNOL., 26:97–108, 2020. © 2019 Society of Plastics Engineers     

Dynamic mechanical,thermal, and morphological properties of silane‐treated montmorillonite reinforced polycarbonate nanocomposites

Three different loading of 3‐aminopropyltriethoxysilane (APS) was used to modify the Na‐montmorillonite via cation exchange technique. The Na‐MMT and silane‐treated montmorillonite (STMMT) were melt‐compounded with polycarbonate (PC) by using Haake Minilab machine. The PC nanocomposite samples were prepared by using Haake Minijet injection molding technique. The intercalation and exfoliation of the PC/MMT nanocomposites were characterized by using X‐ray diffraction (XRD) and transmission electron microscopy (TEM). The thermal properties of the PC nanocomposites were investigated by using dynamic mechanical analyzer and thermogravimetry analyzer. XRD and TEM results revealed partial intercalation and exfoliation of STMMT in PC matrix. Increase of APS concentration significantly enhanced the storage modulus (E′) and improved the thermal stability of PC nanocomposites. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Combining In‐Situ Organic Modification of Montmorillonite and the Latex Compounding Method to Prepare High‐Performance Rubber‐Montmorillonite Nanocomposites

Summary: To improve the interfacial interaction in MMT‐SBR nanocomposites, one type of UOAC was introduced to in‐situ modified MMT before latex compounding with SBR. The influence of the UOAC/MMT ratio on the structure and properties of MMT/SBR nanocomposites were carefully studied by XRD, TEM, and mechanical testing. It was found that through the in‐situ organic modification, a rubber‐intercalated structure of MMT was obtained in the nanocomposites, and the amount of rubber‐intercalated structure strongly depended on the UOAC/MMT ratio. The tensile strength of MMT‐SBR nanocomposites was enhanced dramatically from 4 to 18 MPa by in‐situ organic modification of MMT.

Stress‐strain diagram of SBR/clay nanocomposites.     

Effects of polyurethane soft segment and crosslink density on the morphology and mechanical properties of polyurethane/poly(allyl diglycol carbonate) simultaneous interpenetrating polymer networks

Tough, optically clear simultaneous interpenetrating polymer networks (SINs) of polyurethane (PU) and poly(allyl diglycol carbonate) (ADC) at different compositions were synthesized. The effects of the molecular weight of PU soft segment on the morphology, mechanical properties, and thermal transition behavior of the SINs at two levels of crosslinking agent were studied. The miscibility of PU/ADC SINs, studied by TEM and DMA, was greatly influenced by the SIN composition and the molecular weight of poly(caprolactone) diol (PCL) as the PU soft segment. A single‐phase morphology at a PU concentration of 10% changed to a very fine microheterogeneous morphology as the molecular weight of PCL changed from 530 to 1250. The two‐phase morphology of the PU10/ADC90 SIN based on higher PCL molecular weight (PCL 1250) was also confirmed by DMA, which displayed a sharp peak for the ADC‐rich phase and a small shoulder for the PU‐rich phase transition in the tan δ plot. The SINs at 20–30% PU composition exhibited co‐continuous phase morphology in the transmission electron micrographs, in which the phase regions grew larger as the PCL molecular weight increased from 530 to 1250. All the SIN samples possessed excellent optical transparency except two samples with 30% PU composition based on PCL 1250, which showed a hazy appearance. The tensile strength, modulus, and toughness of the SINs decreased by increasing the molecular weight of PCL from 530 to 1250, whereas the elongations at break remained nearly unchanged. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1583–1595, 2003     

Mechanical and thermal properties of functionalized multiwalled carbon nanotubes and multiwalled carbon nanotube–polyurethane composites

Multiwalled carbon nanotube (MWNT)–polyurethane (PU) composites were obtained by an in situ polycondensation approach. The effects of the number of functional groups on the dispersion and mechanical properties were investigated. The results showed that the functionalized MWNTs had more advantages for improving the dispersion and stability in water and N,N′‐dimethylformamide. The tensile strength and elongation at break of the composites exhibited obvious increases with the addition of MWNT contents below 1 wt % and then decreases with additions above 1 wt %. The maximum values of the tensile strength and elongation at break increased by 900 and 741%, respectively, at a 1 wt % loading of MWNTs. Differential scanning calorimetry measurements indicated that the addition of MWNTs resulted in an alteration of the glass‐transition temperature of the soft‐segment phase of MWNT–PU. Additionally, new peaks near 54°C were observed with differential scanning calorimetry because of the microphase‐separation structures and alteration of the segment molecular weights of the hard segment and soft segment of PU with the addition of MWNTs. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Novel polyether polyurethane/clay nanocomposites synthesized with organicly modified montmorillonite as chain extenders

A kind of novel polyether polyurethane (PU)/clay nanocomposite was synthesized using poly(tetramethylene glycol), 4,4′‐diphenylmethane diisocyanate (MDI), 1,6‐hexamethylenediamine, and modified Na⁺‐montmorillonite (MMT). Here, organicly modified MMT (O‐MMT) was formed by applying 1,6‐hexamethylenediamine as a swelling agent to treat the Na⁺‐MMT. The X‐ray analysis showed that exfoliation occurred for the higher O‐MMT content (40 wt %) in the polymer matrix. The mechanical analysis indicated that, when the O‐MMT was used as a chain extender to replace a part of the 1,2‐diaminopropane to form PU/clay nanocomposites, the strength and strain at break of the polymer was enhanced when increasing the content of O‐MMT in the matrix. When the O‐MMT content reached about 5%, the tensile strength and elongation at break were over 2 times that of the pure PU. The thermal stability and the glass transition of the O‐MMT/PU nanocomposites also increased with increasing O‐MMT content. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 6–13, 2006     

Morphology,thermal, and mechanical properties of polyamide 66/clay nanocomposites with epoxy‐modified organoclay

A new kind of organophilic clay, cotreated by methyl tallow bis‐2‐hydroxyethyl quaternary ammonium and epoxy resin into sodium montmorillonite (to form a strong interaction with polyamide 66 matrix), was prepared and used in preparing PA66/clay nanocomposites (PA66CN) via melt‐compounding method. Three different types of organic clays, CL30B–E00, CL30B–E12, and CL30B–E23, were used to study the effect of epoxy resin in PA66CN. The morphological, mechanical, and thermal properties have been studied using X‐ray diffraction, transmission electron microscopy (TEM), mechanical, and thermal analysis, respectively. TEM analysis of the nanocomposites shows that most of the silicate layers were exfoliated to individual layers and to some thin stacks containing a few layers. PA66CX–E00 and PA66CX–E12 had nearly exfoliated structures in agreement with the SAXS results, while PA66CX–E23 shows a coexistence of intercalated and exfoliated structures. The storage modulus of PA66 nanocomposites was higher than that of the neat PA66 in the whole range of tested temperature. On the other hand, the magnitude of the loss tangent peak in α‐ or β‐transition region decreased gradually with the increase in the clay loading. Multiple melting behavior in PA66 was also observed. Thermal stability more or less decreased with an increasing inorganic content. Young's modulus and tensile strength were enhanced by introducing organoclay. Among the three types of nanocomposites prepared, PA66CX–E12 showed the highest improvement in properties, while PA66CX–E23 showed properties inferior to that of PA66CX–E00 without epoxy resin. In conclusion, an optimum amount of epoxy resin is required to form the strong interaction with the amide group of PA66. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1711–1722, 2006     

Effects on the structure and properties of membranes formed by blending polydimethylsiloxane polyurethane into different soft‐segment waterborne polyurethanes

Polydimethylsiloxane polyurethane (PDMS‐PU), which was synthesized from PDMS as the soft segment, was blended into a variety of ester‐ or ether‐based soft‐segment waterborne polyurethanes with different concentrations to investigate the crystallization, thermal, and physical properties of the membrane formations. According to X‐ray analysis, the ether‐based PUs, synthesized from soft segments of poly(propylene glycol) (PPG1000) or poly(ethylene glycol) (PEG2000), were found to have maximum crystallinity at a 5% blending ratio of PDMS‐PU, but the ester‐based PU, synthesized from soft segments of polycaprolactone (PCL1250), had decreased crystallinity at a 5% blending ratio. Differential scanning calorimetric analysis revealed that the T_g,s values of PUs were highest when the blending ratio of PDMS‐PU was 5%–10%, except for PU from PCL1250. Moreover, ether‐based PUs showed maximum T_m,h values, but the T_m,h of the ester‐based PU was greatly reduced when PU with PCL1250 was blended with PDMS‐PU. In addition, the PU from PEG2000 had the highest melting entropy. Mechanical property analysis showed that the stress of ether‐based PUs would be increased when PUs were blended with a small amount of PDMS‐PU and that the stress of PU from poly(tetramethylene glycol) (PTMG1000) increased to its greatest value (20–30 MPa). On the other hand, the ester‐based PU, from PCL1250 blended with PDMS‐PU, would have reduced stress. On the whole, the stress and strain of PU from PEG1000 had excellent balance. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 210–221, 2006