Electrophoretic deposition of aramid nanofibers on carbon fibers for highly enhanced interfacial adhesion at low content

Here, an anodic electrophoretic deposition was adopted to facilitate the large-scale uniform coating of nano-fillers onto carbon fibers to enhance the interfacial properties between carbon fibers and epoxy matrix. As interface–reinforcing materials, aramid nanofibers were introduced because of their superior mechanical properties and epoxy matrix-friendly functional groups. Furthermore, aramid nanofibers can be readily coated on carbon fibers via electrophoretic deposition because they are negatively-charged in solution with high electrical mobility. Finally, aramid nanofiber-coated carbon fibers showed significantly improved interfacial properties such as higher surface free energy and interfacial shear strengths (39.7% and 34.9% increases, respectively) than those of a pristine carbon fiber despite a very small amount of embedding (0.025 wt% of aramid nanofibers in a carbon fiber), and the short beam strength of the laminated composite prepared with the aramid nanofiber-coated carbon fibers was also improved by 17.0% compared to a non-modified composite.     

Tribo-mechanical characterization of reinforced epoxy resin under dry and lubricated contact conditions

The aim of the present work is to investigate the influence of the reinforcing material and architecture on the voids content, mechanical properties and tribological behavior of fiber reinforced epoxy composite laminates manufactured by VARTM under different processing conditions. Two different textile architectures, namely unidirectional non-crimp fabrics (UD) and 0/90 plain wave (PW), were considered, reinforcing an EPIKOTE RIMR 135 epoxy matrix with glass (GF) as well as carbon (CF) continuous fibers. Optical observations revealed an unexpected trend relatively to the intra- and inter-bundle voids concentration with respect to the impregnation velocity, especially using UD-CF and UD-GF reinforcements and low impregnation rate. Tensile and three points bending tests highlighted the dominant role of fiber material and architecture on mechanical properties, whereas the presence of voids played a minor role with respect to the analyzed features. Tribological outcomes evidenced a reduction of the friction coefficient (μ) when the resin is reinforced by carbon or glass fibers. The lowest values were detected when the sliding direction of the counterbody is oriented parallel to the fiber direction for UD samples. Further reduction of μ, for both UD and PW specimens, was obtained by interposing a lubricant at the interface.     

Effect of fiber loading on the properties of treated cellulose fiber-reinforced phenolic composites

The effect of fiber loading on the properties of treated cellulose fiber-reinforced phenolic composites was evaluated. Alkali treatment of the fibers and reaction with organosilanes as coupling agents were applied to improve fiber–matrix adhesion. Fiber loadings of 1, 3, 5, and 7 wt% were incorporated to the phenolic matrix and tensile, flexural, morphological and thermal properties of the resulting composites were studied. In general, mechanical properties of the composites showed a maximum at 3% of fiber loading and a uniform distribution of the fibers in such composites was observed. Silane treatment of the fibers provided derived composites with the best thermal and mechanical properties. Meanwhile, NaOH treatment improved thermal and flexural properties, but reduced tensile properties of the materials. Therefore, the phenolic composite containing 3% of silane treated cellulose fiber was selected as the material with optimal properties.     

Effects of potassium titanate whiskers and carbon fibers on the wear behavior of polyetheretherketone composite under water lubricated condition

The tribological behaviors of polyetheretherketone (PEEK) composite reinforced by carbon fiber (CF) and potassium titanate whiskers (PTW) have been investigated using the pin-on-disk configuration at different applied loads under water lubricated condition. The effects of micrometer carbon fiber and sub-micrometer PTW on the wear properties of the hybrid composite have been discussed. It was found that the PEEK/PTW/CF composite showed excellent tribological performance in water condition. High wear resistance and low friction coefficient were achieved under a wide range of loads. It was revealed that the two fillers worked synergetically to enhance the wear resistance of the hybrid reinforced PEEK composite. The carbon fiber carried the main load between the contact surfaces and protected the matrix from further severe abrasion of the counterpart. At the same time, the exposed PTW out of the polymer matrix around the fiber inhibited the direct scraping between the fiber edge and counterpart tip in some degree, so that the fibers could be less directly impacted during the subsequent sliding process and they were protected from severe damage. In addition, the reinforcement effect of PTW on PEEK could reduce the stress concentration on the carbon fiber-matrix interface, and thereby reduce the CF failure/damage. The reinforcement effect of PTW on PEEK might also restrict the crack initiation and propagation on the surface and subsurface of the composite, and therefore to protect the matrix from fatigue failure during the sliding process.     

Mechanical and tribological properties of self-lubricating metal matrix nanocomposites reinforced by carbon nanotubes (CNTs) and graphene – A review

Rapid innovation in nanotechnology in recent years enabled development of advanced metal matrix nanocomposites for structural engineering and functional devices. Carbonous materials, such as graphite, carbon nanotubes (CNT's), and graphene possess unique electrical, mechanical, and thermal properties. Owe to their lubricious nature, these carbonous materials have attracted researchers to synthesize lightweight self-lubricating metal matrix nanocomposites with superior mechanical and tribological properties for several applications in automotive and aerospace industries. This review focuses on the recent development in mechanical and tribological behavior of self-lubricating metallic nanocomposites reinforced by carbonous nanomaterials such as CNT and graphene. The review includes development of self-lubricating nanocomposites, related issues in their processing, their characterization, and investigation of their tribological behavior. The results reveal that adding CNT and graphene to metals decreases both coefficient of friction and wear rate as well as increases the tensile strength. The mechanisms involved for the improved mechanical and tribological behavior is discussed.     

Comparative study of high temperature composites

Two classes of composite made using either ceramic matrix with high temperature fibers or carbon/carbon have been used for various applications that require high temperature resistance, over three decades. However, their use has been limited to special applications because of the high costs associated with fabrication. Typically the composites are cured at more than 1000°C, and in most instances the heating has also to be carried out in controlled environments. In addition, because of the high processing temperature, only certain type of expensive fibers can be used with the ceramic matrices. A recently developed inorganic matrix, called polysialate can be cured at temperatures less than 150°C, making it possible to use carbon and glass fibers. Composites made using carbon, glass and combinations of carbon and glass fibers have been tested in bending and tension. This paper presents the comparison of processing requirements and mechanical properties of carbon/carbon composites, ceramic matrix composites made with silicon carbide, silicon nitride and alumina fibers and carbon/polysialate composites. The results indicate that carbon/polysialate composite has mechanical properties comparable to both carbon/carbon and ceramic matrix composites at room and high temperatures. Since the polysialate composites are much less expensive, the authors believe that it has excellent potential for more applications in aerospace, automobile and naval structures.     

Augmented fatigue performance and constant life diagrams of hierarchical carbon fiber/nanofiber epoxy composites

We report the results of an extensive multi-stress ratio experimental study on the axial fatigue behavior of an all-carbon hierarchical composite laminate, in which carbon nanofibers (CNFs) are utilized alongside traditional micron-sized carbon fibers. Primary carbon fibers were arranged in matrix-dominated biax ±45° lay-ups in order to establish matrix and matrix/fiber interaction based performance. CNFs were matrix dispersed by three-roll calender milling. Results indicate that the CNF-reinforced composites collectively possess improved fatigue and static properties over their unmodified counterparts. Large mean lifetime improvements of 150–670% were observed in fully compressive, tensile and tensile dominated loadings. Enhancements are attributed to the high interface density and damage shielding effect of the CNFs within the matrix. Further improvements are believed to occur when the nanofibers arrest and redistribute small scale, slowly propagating matrix cracks at low applied stresses. These results highlight the ability of a nanometer-sized reinforcing phase to actively participate and enhance matrix properties while moving toward a cost effective alternative to current material solutions.     

Novel wear-resistant materials - Carbon fiber reinforced low-carbon Stellite alloy composites

This paper reports the design and development of a class of new composite materials, which are low-carbon Stellite alloy matrices reinforced with carbon fibers. The focus of the research is to compare the different effects of carbon fibers versus carbides on Stellite alloys. Stellite 25 was selected as the matrix because of its very low carbon content (0.1 wt.%), thus minimal carbide volume fraction. The composite specimens are fabricated using the hot isostatic pressing and sintering techniques. The microstructures of the specimens are examined with optical microscopy in order to identify the possible carbide formation from the carbon fibers. The material characterization of the specimens is achieved through hardness test, sliding wear test and corrosion test. These novel materials exhibit superior properties compared to existing Stellite alloys and are expected to spawn a new generation of materials used for high temperature, severe corrosion, and wear resistant applications in various industries.     

Influence of carbon nanotube-polymeric compatibilizer masterbatches on morphological, thermal, mechanical, and tribological properties of polyethylene

Study was made of the effect of multiwall carbon nanotubes (MWCNTs) and polymeric compatibilizer on thermal, mechanical, and tribological properties of high density polyethylene (HDPE). The composites were prepared by melt mixing in two steps. Carbon nanotubes (CNTs) were melt mixed with maleic anhydride grafted polyethylene (PEgMA) as polymeric compatibilizer to produce a PEgMA-CNT masterbatch containing 20 wt% of CNTs. The masterbatch was then added to HDPE to prepare HDPE nanocomposites with CNT content of 2 or 6 wt%. The unmodified and modified (hydroxyl or amine groups) CNTs had similar effects on the properties of HDPE-PEgMA indicating that only non-covalent interactions were achieved between CNTs and matrix. According to SEM studies, single nanotubes and CNT agglomerates (size up to 1 μm) were present in all nanocomposites regardless of content or modification of CNTs. Addition of CNTs to HDPE-PEgMA increased decomposition temperature, but only slight changes were observed in crystallization temperature, crystallinity, melting temperature, and coefficient of linear thermal expansion (CLTE). Young’s modulus and tensile strength of matrix clearly increased, while elongation at break decreased. Measured values of Young’s moduli of HDPE-PEgMA-CNT composites were between the values of Young’s moduli for longitudinal (E₁₁) and transverse (E₂₂) direction predicted by Mori-Tanaka and Halpin-Tsai composite theories. Addition of CNTs to HDPE-PEgMA did not change the tribological properties of the matrix. Because of its higher crystallinity, PEgMA possessed significantly different properties from HDPE matrix: better mechanical properties, lower friction and wear, and lower CLTE in normal direction. Interestingly, the mechanical and tribological properties and CLTEs of HDPE-PEgMA-CNT composites lie between those of PEgMA and HDPE.     

Mechanical behavior of self-assembled carbon nanotube reinforced nylon 6,6 fibers

The versatile electrospinning technique was used to successfully align and disperse multiwalled carbon nanotubes (MWCNT) in nylon 6,6 matrix to obtain composite fibers. The morphology of the composite fibers and the dispersion of the CNTs within the fibers were analyzed using scanning electron microscopy (SEM) and transmission electron microscopy (TEM), respectively. TEM analysis revealed that the CNTs were well-dispersed, separated and aligned along the fiber axis. The thermal and mechanical properties of the composite fibers were characterized as a function of weight fraction of the CNTs. Incorporation of the CNTs in the fibers resulted in an increase in glass-transition temperature (T_g) by ∼7 °C, indicating that the addition of CNTs has restricted the mobility of the polymer chains and provided confinement to neighboring molecular chains. Tensile and nanoindentation experiments were performed to investigate the mechanical deformation behavior of the composite fibers. The results suggested that incorporation of high strength and high aspect ratio CNTs into the fiber matrix enhanced significantly the stiffness and strength of nylon 6,6 fibers. An understanding of the structure–property relationships can provide fruitful insights to develop electrospun fibers with superior properties for miniaturized and load-bearing applications.     

Reinforcement of plasticized wheat gluten with natural fibers: From mechanical improvement to deplasticizing effect

Wheat gluten/glycerol-based materials were reinforced through natural fiber addition. Hemp and wood fiber addition increased both composite tensile strength and Young’s modulus, but decreased elongation at break. Resulting materials exhibited lower water sensitivity. Fiber addition does not modify the protein aggregation, but resulted in an increase of the composite matrix glass transition temperature (T_g). This increase was attributed to the plasticizer migration from the matrix to the fibers, which increased the matrix Young’s modulus. This migration called matrix deplasticization contributed to the improvement of the overall composite mechanical properties. The true reinforcing effect attributed to the fiber addition and the deplasticizing effect attributed to plasticizer migration were dissociated and quantified. At high fiber content, deplasticizing effect became significant and reduced material processability. This study suggested that the fiber lignin content is susceptible to influence both the water sensitivity and the matrix deplasticization.     

Influence of the fiber/matrix strength on the mechanical properties of a glass fiber/thermoplastic-matrix plain weave fabric composite

In this work, we analyze the influence of different fiber surface treatments on the mechanical properties of plain weave composites. The reinforcement is a glass fibers fabric and the matrix is an acrylic polymer. Until very recently, this thermoplastic polymer family was not used in composite industry. It is therefore necessary to study if the existing fiber surface treatments are suitable for acrylic resins or if new ones have to be found. At the macroscale, composite materials corresponding to different fiber surface treatments were characterized with: (i) monotonic in-plane shear tests and (ii) heat-build up fatigue measurements on specimens with ±45° fiber orientations with respect to the tensile force. At the mesoscale (fabric scale), the development of damage was experimentally analyzed from (i) 3-D DIC (Digital Image Correlation) full-field strain measurements with spatial resolution smaller than the textile repeating unit and (ii) X-ray microtomography. We show that the analyzed composite materials exhibit linear viscoelastic behavior until a given stress threshold above which damage develops in the material. It was also found that the application on the fibers of a coupling agent specifically developed for promoting the bond between glass fibers and acrylic resins improves the composite mechanical properties, in particular the fatigue properties.     

Tribological and mechanical properties of the composites made of carbon fabrics modified with various methods

Carbon fabric (CF) was modified with strong HNO₃ etching, plasma bombardment, and anodic oxidation, respectively. The modified carbon fabric was then used to prepare carbon fabric composites (CFC) by dip-coating in a phenolic resin and the relative mass content of carbon fabric in the carbon fabric composites is 65%. The friction and wear behaviors of the carbon fabric composites were evaluated with a Xuanwu-III high temperature friction and wear tester, and their mechanical properties were evaluated on a Shimadzu™ universal materials testing machine, respectively. The changes in the chemical compositions of the unmodified and modified carbon fabrics were analyzed by means of X-ray photoelectron spectroscopy. The morphologies of the worn surfaces of the unmodified and modified carbon fabric composites were analyzed by means of scanning electron microscopy. It was found that the friction-reduction and anti-wear properties of the carbon fabric composites were improved by anodic oxidation, plasma bombardment, and strong HNO₃ etching, so were the mechanical properties and load-carrying capacity. The composite made of the carbon fabric modified with anodic oxidation showed the best tribological and mechanical properties, and the one made of the carbon fabric etched with HNO₃ had the poorest tribological and mechanical properties among the three kinds of the tested composites. The active groups were produced during the oxidation process, which contributed to strengthen the bonding strength between the carbon fabric and the adhesive and hence to improve the tribological and mechanical properties of the composites made of the modified carbon fabric. The friction and wear properties of the carbon fabric composites were closely dependent on the environmental temperature. Namely, the wear rates of the composites at elevated temperature above 180 °C were much larger than that below 180 °C, which was attributed to the degradation and decomposition of the adhesive resin at excessively elevated temperature. Moreover, the composite made of the carbon fabric modified with anodic oxidation had better thermal stability than the one made of the unmodified carbon fabrics.     

Hierarchical wood cellulose fiber/epoxy biocomposites – Materials design of fiber porosity and nanostructure

Delignified chemical wood pulp fibers can be designed to have a controlled structure of cellulose fibril aggregates to serve as porous templates in biocomposites with unique properties. The potential of these fibers as reinforcement for an epoxy matrix (EP) was investigated in this work. Networks of porous wood fibers were impregnated with monomeric epoxy and cured. Microscopy images from ultramicrotomed cross sections and tensile fractured surfaces were used to study the distribution of matrix inside and around the fibers – at two different length scales. Mechanical characterization at different relative humidity showed much improved mechanical properties of biocomposites based on epoxy-impregnated fibers and they were rather insensitive to surrounding humidity. Furthermore, the mechanical properties of cellulose-fiber biocomposites were compared with those of cellulose-nanofibril (CNF) composites; strong similarities were found between the two materials. The reasons for this, some limitations and the role of specific surface area of the fiber are discussed.     

Flexural and compression response of woven E-glass/polyester–CNF nanophased composites

A significant improvement in fiber reinforced polymeric composite (FRPC) materials can be obtained by incorporating a very small amount of nanofiller in the matrix material. In this work, an ultrasonic liquid processor was used to infuse carbon nanofiber (CNF) into the polyester matrix which was then mixed with catalyst using a mechanical agitator. Both conventional and CNF-filled glass-fiber reinforced polyester composites (GRPC) were fabricated using the vacuum assisted resin transfer molding (VARTM) process. Excellent dispersion of CNFs into the polyester resin was observed from the scanning electron microscopy (SEM) micrographs. Flexural and quasi-static tests were performed for investigating the mechanical responses. Fracture surface was examined using optical microscopy (OM) and SEM. Flexure tests performed on the conventional GRPC, 0.1–0.4 wt.% CNF-filled GRPC showed up to 49% and 31% increase in the flexural strength and modulus, respectively, compared to the conventional one with increasing loading of CNFs up to 0.2 wt.%. Similar trend was seen in quasi-static compression properties. SEM evaluation revealed relatively less damage in the tested fracture surfaces of the nanophased composites in terms of matrix failure, fiber breakage, matrix–fiber debonding, and delamination, compared to the conventional one. This might be the result of better interfacial interaction between matrix and fibers, due to the presence of CNFs.     

Preparation and characterization of novel biodegradable composites based on acylated cellulose fibers and poly(ethylene sebacate)

The preparation and characterization of biodegradable composite materials with improved properties based on poly(ethylene sebacate) (PES) and acylated cellulose fibers is reported. These biocomposites showed improved mechanical properties, as evidenced by the increase in both elastic and Young moduli and in the tensile strength, and also showed low water sensitivity and a high biodegradability rate. These novel biocomposites were prepared essentially from renewable resources and therefore constitute an important contribution to the development of the area of sustainable composite materials.     

Effects of carbon nanotube functionalization and annealing on crystallization and mechanical properties of melt-spun carbon nanotubes/poly(ethylene terephthalate) fibers

To generate poly(ethylene terephthalate) (PET) fibers with enhanced mechanical properties, we prepared melt-spun PET fibers that incorporated pristine, acid-treated, and functionalized multi-walled carbon nanotubes (MWNTs) with 2-phenylethyl alcohol and 4-phenyl-1-butanol. The incorporation of MWNTs into the melt-spun fibers resulted in increased crystallization of PET but lower breaking stress than that of pure PET fibers, even in those containing well-dispersed functionalized MWNTs. The breaking stress of drawn composite fibers was also lower than that of pure PET fibers prepared at the same draw ratio. However, the annealing of melt-spun fibers enhanced the mechanical properties and crystallization, and the annealing effect was more dominant for composite fibers with functionalized MWNTs. These findings indicate that the presence of well-dispersed MWNTs disturbs the crystallization and orientation of PET molecules in highly stressed fibers, which differs from MWNT-induced crystallization of PET molecules in relaxed fibers.     

Developing rigid gliadin based biocomposites with high mechanical performance

We aim to produce unidirectional fiber composites with high mechanical performance based on flax fibers and a rigid gliadin matrix. As a fraction from wheat gluten, gliadin is soluble in alcohol containing media. The fabrication process did not involve any further solvents or plasticizers. Finally, samples were cooled at different rates. Overall, the cooling rate does not strongly affect the mechanical properties although slowly cooled materials contain a higher amount of non-disulfide cross-links, next to disulfide bonds within the gliadin matrix. At 40% fiber volume fraction, flax/gliadin composites with a flexural modulus and strength of respectively 21.5 GPa and 240 MPa were obtained when loaded in the longitudinal direction. These high values demonstrate that in this composite fabrication process, a good impregnation of the polymer matrix in between the fiber bundles has been achieved. However, the fiber–matrix adhesion, as measured by transverse flexural and tensile tests, was still relatively modest.     

Additive manufacturing of carbon fiber reinforced thermoplastic composites using fused deposition modeling

Additive manufacturing (AM) technologies have been successfully applied in various applications. Fused deposition modeling (FDM), one of the most popular AM techniques, is the most widely used method for fabricating thermoplastic parts those are mainly used as rapid prototypes for functional testing with advantages of low cost, minimal wastage, and ease of material change. Due to the intrinsically limited mechanical properties of pure thermoplastic materials, there is a critical need to improve mechanical properties for FDM-fabricated pure thermoplastic parts. One of the possible methods is adding reinforced materials (such as carbon fibers) into plastic materials to form thermoplastic matrix carbon fiber reinforced plastic (CFRP) composites those could be directly used in the actual application areas, such as aerospace, automotive, and wind energy. This paper is going to present FDM of thermoplastic matrix CFRP composites and test if adding carbon fiber (different content and length) can improve the mechanical properties of FDM-fabricated parts. The CFRP feedstock filaments were fabricated from plastic pellets and carbon fiber powders for FDM process. After FDM fabrication, effects on the tensile properties (including tensile strength, Young's modulus, toughness, yield strength, and ductility) and flexural properties (including flexural stress, flexural modulus, flexural toughness, and flexural yield strength) of specimens were experimentally investigated. In order to explore the parts fracture reasons during tensile and flexural tests, fracture interface of CFRP composite specimens after tensile testing and flexural testing was observed and analyzed using SEM micrograph.     

Tribological behaviour and wear of carbon nanotubes grafted on carbon fibres

Carbon nanotubes (CNTs) grafted on fibres are widely used to reinforce composites in order to improve their mechanical properties. This study concerned the tribological properties of CNTs grafted on carbon fibres by the flame method. The aim of this study was to determine whether CNTs on fibres suffer damage under stress, similar to those applied during composite manufacturing, which can damage composite properties, particularly fibre/matrix adhesion. For this purpose, reciprocating friction tests were performed to examine the resistance of CNTs and highlight a wear mechanism. The results showed that the presence of CNTs increased the coefficient of friction in the first friction cycles and then decreased it to close to the COF of the fibre without CNTs. The wear mechanism showed that after a small number of friction cycles, the CNTs were flattened out and formed a transfer film.