Effect of graphene oxide on the physical,mechanical and thermo-mechanical properties of neoprene and chlorosulfonated polyethylene vulcanizates

The present research work demonstrated the effect of graphene oxide (GO) on the physical, mechanical, thermo-mechanical etc., properties of neoprene (CR) and chlorosulfonated polyethylene (CSPE) vulcanizates. CR and CSPE based nanocomposites were prepared by both solution intercalation and melt intercalation methods. The changes obtained in the morphology, cure characteristics, mechanical, thermal, thermo-mechanical properties of the rubber nanocomposites have been widely investigated. X-ray diffraction analysis (XRD) and transmission electron microscopic (TEM) analysis of the samples revealed partial exfoliated structure of GO containing rubber composites. Mechanical, thermal, cure and thermo-mechanical properties of the elastomeric nanocomposites were improved compared to the neat rubbers.     

Effects of carbon nanotube aspect ratio on strengthening and tribological behavior of ultra high molecular weight polyethylene composite

Carbon-based nanomaterials are great choice as reinforcement to Ultra-High Molecular-Weight Polyethylene (UHMWPE), with potential use in orthopedics. While high in-plane-stiffness and strength of these nanomaterials help in toughening, their weaker out-of-plane integrity offers lubrication. Present study investigates effect of aspect ratio of carbon nanotubes (CNT) on toughening and solid-lubrication efficiency of UHMWPE-matrix. A nominal 0.05–0.1 wt.% of CNT addition increases hardness and elastic modulus of UHMWPE by 3–45% and 8–42%, respectively. Higher aspect ratio (HAR) CNTs are found more effective in improving hardness and modulus of UHMWPE. Wear rate and friction-coefficient also increase by 530% and 220%, respectively, while reinforced with HAR CNTs. Thermal analysis shows slight increase in crystallinity and stability of composite. HAR CNTs improve interfacial bonding with matrix, due to their morphological similarity to polymer chains, as compared to low aspect ratio CNT. Aspect ratio of CNTs significantly dominates strengthening and tribological behavior of UHMWPE.     

Highly conductive graphene oxide/polyaniline hybrid polymer nanocomposites with simultaneously improved mechanical properties

Graphene oxide (GO) was added to a polymer composites system consisting of surfactant-wrapped/doped polyaniline (PANI) and divinylbenzene (DVB). The nanocomposites were fabricated by a simple blending, ultrasonic dispersion and curing process. The new composites show higher conductivity (0.02–9.8 S/cm) than the other reported polymer system filled with PANI (10⁻⁹–10⁻¹ S/cm). With only 0.45 wt% loading of GO, at least 29% enhancement in electric conductivity and 29.8% increase in bending modulus of the composites were gained. Besides, thermal stability of the composites was also improved. UV–Vis spectroscopy, X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) revealed that addition of GO improves the dispersion of PANI in the polymer composite, which is the key to realize high conductivity.     

Functionalizing graphene decorated with phosphorus-nitrogen containing dendrimer for high-performance polymer nanocomposites

In this paper, we demonstrate a novel strategy for fabricating advanced polymer composites based on functionalized graphene oxide decorated with phosphorus-nitrogen-containing dendrimers (PND-GO). Both X-ray diffraction and transmission electron microscopy results show that reduced PND-GO uniformly disperses within polymer matrix and is exfoliated in polyurethane (PU) via in situ polymerization. Cone calorimetry results show that incorporating 2 wt% reduced PND-GO into PU decreases the peak heat release rate by 53% and prolongs the time to ignition by 28 s as compared with the PU bulk. Besides, the tensile strength and Young’s modulus are remarkably enhanced by about 2 times and 5 times, respectively.     

Free-volume correlation with mechanical and dielectric properties of natural rubber/multi walled carbon nanotubes composites

The microstructure, mechanical strength, dielectric properties, Doppler broadening measurements and positron life time studies of the composites containing multi walled carbon nanotubes (MWCNTs) and natural rubber (NR) are investigated. The uniform distribution of MWCNTs in the elastomer medium is studied by Raman spectroscopy and the electron microscopy images show the composite’s internal microstructure. Free volume sizes and interstitial mesopore sizes of the nanocomposites are determined by positron annihilation lifetime spectroscopy (PALS). PALS investigates the influence of the nanotubes in regulating the interphase nanoscale character. Strong interfacial interaction causes an apparent reduction of the free-volume fraction of NR probably by depressing the formation of free-volume holes in the interfacial region. The mechanical percolation and percolation observed from the dielectric measurements are correlated with the life time values. It is established that the sub-nano level free volumes and nano level structure of the composites have significant roles in regulating the mechanical properties.     

Multi-functional hindered amine light stabilizers-functionalized carbon nanotubes for advanced ultra-high molecular weight Polyethylene-based nanocomposites

Hindered Amine Light Stabilizer (HAS) molecules have been covalently linked on the outer surface of multi-walled carbon nanotubes (CNTs), and the so-obtained multi-functional fillers (HAS-f-CNTs) have been compounded with Ultra High Molecular Weight Polyethylene (UHMWPE) to get composite films. The success of the grafting reaction of the HAS molecules has been confirmed through spectroscopic and thermo-gravimetric analyses. Morphological analyses reveal a segregated microstructure, in which CNT-rich channels surround the polymer domains. This morphology results in improved mechanical properties and appreciable electrical conductive features. More importantly, the addition of only 1 wt.% of HAS-f-CNTs brings about a significant improvement of the photo-oxidation resistance, which neither HAS nor CNTs can provide if used separately. The origin of this synergic effect is discussed. Overall, our results demonstrate the possibility of using properly functionalized CNTs as multi-functional fillers to get high-performance polymer composites.     

Structure and properties of hybrid PLA nanocomposites with inorganic nanofillers and cellulose fibers

Polylactide reinforced with 3 wt% of organo-modified montmorillonite, 5 wt% of stearic acid-modified calcium carbonate nanoparticles, 15 wt% of cellulose fibers (PLA/MMT, PLA/NCC, PLA/CF) and hybrid composites containing 15 wt% of fibers in addition to montmorillonite (PLA/MMT/CF) or calcium carbonate (PLA/NCC/CF) were prepared and examined. The nanoparticles were dispersed in polylactide almost homogeneously; montmorillonite was exfoliated during processing. T_g of polylactide remained unaffected but its cold crystallization was enhanced; the cold-crystallization behavior of the hybrid composites was dominated by nanofillers nucleating ability. The fibers and calcium carbonate decreased whereas exfoliated montmorillonite improved the thermal stability of the materials. Polylactide, PLA/NCC and PLA/MMT exhibited ability to plastic deformation, although the latter the weakest. Tensile behavior of the hybrid composites was strongly influenced by the fibers and similar to that of PLA/CF. All the fillers increased the storage modulus below T_g; that of PLA/MMT/CF and PLA/NCC/CF was improved with respect to polylactide by 50% and 45%, respectively.     

Effect of ZnO nanoparticles doped graphene on static and dynamic mechanical properties of natural rubber composites

In this work, effect of ZnO nanoparticles doped graphene (Nano-ZnO–GE) on static and dynamic mechanical properties of natural rubber composites were studied. Nano-ZnO–GE was synthesized by sol–gel method and thermal treatment. With the incorporation of nano-ZnO–GE into the matrix, the mechanical properties of NR nanocomposite significantly improved over that of NR composite containing with 5 phr of conventional-ZnO. The results demonstrated that the presence of nano-ZnO on the surface of graphene sheets not only conduces to suppressing aggregation of graphene sheets but also acts as a more efficient cure-activator in vulcanization process, with the formation of excellent crosslinked network at low nano-ZnO–GE content. This work also showed that NR/Nano-ZnO–GE nanocomposites exhibited higher wet grip property and lower rolling resistance compared with NR/Conventional-ZnO composite, which makes nano-ZnO–GE very competitive for the green tire application as a substitute of conventional-ZnO, enlarging versatile practical application to prepare high-performance rubber nanocomposites.     

New models for yield strength of polymer/clay nanocomposites

In this paper, a new and simple model is presented for tensile yield strength of polymer/clay nanocomposites assuming the plate-like shape of silicate layers. Moreover, the accuracy of Pukanszky model which is initially developed for polymer composites filled with quasi-spherical particles is improved for silicate layered nanocomposites based on the suggested model. Many nanocomposites are provided from valid literature to estimate the accuracy of the proposed models and to calculate “k₁” and “B₁” parameters in the suggested equation and improved Pukanszky model, respectively. Furthermore, the developed models are joined to approximate the critical values of parameters which show the strengthening of polymer nanocomposites by nanoclay platelets. The large efficiency of the proposed approaches is confirmed, when the experimental data are compared with the calculations.     

Nanocomposites based on polystyrene-b-poly(ethylene-r-butylene)-b-polystyrene and exfoliated graphite nanoplates: Effect of nanoplatelet loading on morphology and mechanical properties

Exfoliated graphite nanoplates (xGnPs)/polystyrene-b-poly(ethylene-r-butylene)-b-polystyrene (SEBS) nanocomposites have been prepared by the simple melt-compounding approach. The structural, mechanical and viscoelastic properties of these composites were studied and compared. Wide-angle X-ray diffraction (WAXD) studies indicated that the processing of nanocomposites did not change the original d-spacing of xGnPs. Scanning electron microscopy observation on the fracture surfaces of the composites shows a uniform dispersion of xGnPs throughout SEBS matrix and strong interfacial adhesion between oxidized xGnPs and the matrix, which are responsible for the considerable enhancement of mechanical properties of the composites. It is found that the addition of xGnPs particles improved both the elastic modulus and storage modulus of pure SEBS significantly and the higher the xGnPs content, the higher the modulus of the nanocomposite. Moreover, the effects of dispersed xGnPs on the microphase separation of SEBS have also been investigated using small angle X-ray scattering (SAXS).     

Click coupled stitched graphene sheets and their polymer nanocomposites with enhanced photothermal and mechanical properties

The chemically stitched graphene oxide (GO) sheets were obtained using a click chemistry reaction between azide-functionalized GO and alkyne-functionalized GO. The click coupled GO (GO-click-GO) sheets showed the largely increased electrical conductivity and near infrared laser-induced photothermal properties compared to the GO sheets, which result from formation of triazole ring as a bridging linker between the GO sheets. The polyurethane (PU) nanocomposites incorporating the GO-click-GO sheets exhibited enhanced mechanical properties of breaking stress and modulus than the GO/PU nanocomposites. The modulus of GO-click-GO/PU nanocomposites was higher than that of the GO/PU nanocomposites at the same filler loading of 0.1 and 0.5 wt%. The GO-click-GO/PU nanocomposites also showed a significantly improved photothermal properties compared to the GO/PU nanocomposites at the same filler loading. The click coupled stitched GO sheets in this study can be used as the superior reinforcing fillers for mechanically and photothermally high performance polymer nanocomposites.     

Evaluation of thermal,mechanical, and electrical properties of PVDF/GNP binary and PVDF/PMMA/GNP ternary nanocomposites

Graphene nanoplatelet (GNP) was incorporated into poly(vinylidene fluoride) (PVDF) and PVDF/poly(methyl methacrylate) (PMMA) blend to achieve binary and ternary nanocomposites. GNP was more randomly dispersed in binary composites compared with ternary composites. GNP exhibited higher nucleation efficiency for PVDF crystallization in ternary composites than in binary composites. GNP addition induced PVDF crystals with higher stability; however, PMMA imparted opposite effect. The binary composite exhibited lower thermal expansion value than PVDF; the value further declined (up to 28.5% drop) in the ternary composites. The storage modulus of binary and ternary composites increased to 23.1% and 53.9% (at 25 °C), respectively, compared with PVDF. Electrical percolation threshold between 1 phr and 2 phr GNP loading was identified for the two composite systems; the ternary composites exhibited lower electrical resistivity at identical GNP loadings. Rheological data confirmed that the formation of GNP (pseudo)network structure was assisted in the ternary system.     

Fluorinated graphene reinforced polyimide films with the improved thermal and mechanical properties

In order to explore the addition effect of fluorinated graphene (FG) on the mechanical and thermal performances of polyimide (PI) matrix, FG sheets are first prepared and employed as the nanofillers to construct PI/FG nanocomposite films. The prepared film is optically transparent at low content of FG and experimental results demonstrate that the addition of FG can effectively enhance the properties of PI matrix. Especially, compared with pure PI matrix, the addition of 0.5 wt% FG in PI can endow 30.4% increase in tensile stress and 115.2% increase in elongation at break. Experimental analyses considering the morphology and microstructure are also conducted, and the results indicate that the improved mechanical properties of the PI/FG nanocomposite films are mainly attributed to the good dispersibility of FG sheets in PI host, and the effective stress transfer between the polymer and the FG.     

Defect-free MoS2 nanosheets: Advanced nanofillers for polymer nanocomposites

The preparation of defect-free MoS₂ nanosheets is a key challenge and essential for practical applications. Herein the dodecanethiol was firstly performed as the antioxidant and surface modifier to produce the defect-free MoS₂ by direct ultrasonication of bulk MoS₂ in N,N-dimethylformamide. Incorporating defect-free MoS₂ into polyethylene obviously improved the properties of PE/MoS₂ nanocomposites. For crystallization under quiescent condition, the half crystallization time (t₀.₅) of nanocomposites containing 0.2 wt% MoS₂ was reduced by 87.0% compared to that of neat PE. A 54.3 °C increase in the temperature of maximum weight loss (T_max) was observed by inclusion of as low as 0.7 wt% defect-free MoS₂ nanosheets. In addition, the uniformly distributed MoS₂ can considerably improve the mechanical properties of composites. These observations suggest that the robust nature, dramatic barrier action of defect-free MoS₂ and the strong nanosheets/matrix interfacial adhesion would be the motivation to improve the performance of the polymeric nanocomposites.     

Preparation and properties of reduced graphene oxide/polyacrylonitrile nanocomposites using polyvinyl phenol

Nanocomposites of polyacrylonitrile (PAN) with reduced graphene oxide (rGO) were prepared using a solution mixing technique employing polyvinyl phenol (PVP) as a compatibilizer. The PVP can facilitate composite formation by interacting with both rGO and PAN via π-π and H-bonding respectively. Various amounts of rGO were used to prepare PAN nanocomposites. The cross-sectional morphology of the composite films shows a uniform dispersion of rGO sheets in the PAN matrix. The Fourier transform infrared (FT-IR) studies revealed that good interaction of the rGO/PVP hybrid with PAN. The wide angle x-ray diffraction (WAXS) study confirms that the rGO sheets were uniformely dispersed as individual sheets in the PAN matrix. Thermogravimetric analysis shows enhanced thermal stability of the composite compared to pure PAN. The tensile strength and elastic modulus of the nanocomposites increased with increasing rGO content. A 102% enhancement in tensile strength and a 62.9% enhancement in elastic modulus were observed in the nanocomposite with 5% rGO.     

Preparation of thermally reduced graphene oxide and the influence of its reduction temperature on the thermal,mechanical, flame retardant performances of PS nanocomposites

In this article, we investigated the influence of thermally reduced graphene oxides (TGOs) at different reduction temperatures on the thermal, mechanical and flame retardant performances of polystyrene (PS). The results indicated that disordered expanded layer structure can be obtained as the reduction temperature increases from 200 to 500 and 800 °C (the resulted composites are named as PS/TGO2, PS/TGO5 and PS/GTO8, respectively), which could lead to better dispersion of TGO sheets in PS matrix. Dynamic mechanical thermal analysis showed that both the storage modulus and T_g of PS/TGO5 and PS/TGO8 nanocomposites are significantly improved compared with that of neat PS. Noticeable improvement in flame retardant performance were achieved with the addition of TGO5 and TGO8, particularly TGO8, due to the removal of the functional oxygen groups from GO and the barrier effect of intumescent and loosely structure of char layers.     

Electrical and mechanical properties of antistatic PVC films containing multi-layer graphene

In order to explore practical application of graphene as novel conductive fillers in the filed of composite materials, we prepared anti-static multi-layer graphene (MLG) filled poly(vinyl chloride) (PVC) composite films by using conventional melt-mixing method, and investigated electrical conductivity, tensile behavior, and thermal properties of the MLG/PVC composite films. We found that the presence of MLG can greatly increase electrical conductivity of the MLG/PVC composites, and the surface electrical conductivity of the MLG/PVC composites is less than 3 × 10⁸ Ohm/square when the MLG loading is about 3.5 wt%, meeting anti-static requirement for commercial anti-static PVC films. On the other hand, the MLG/PVC composites exhibited higher tensile modulus and higher glass transition temperature than neat PVC, which is closely associated with crumpled morphology of the MLG and good compatibility between components of the MLG/PVC composites. By virtue of its satisfied anti-static performance and high mechanical properties, the MLG/PVC composites exhibit great potential to be used as high-performance antistatic materials in many fields.     

Effect of shearing on the orientation, crystallization and mechanical properties of HDPE/attapulgite nanocomposites

High density polyethylene (HDPE)/attapulgite (AT) nanocomposites, prepared by conventional injection molding (CIM) and dynamic packing injection molding (DPIM), were investigated with focus on AT-induced crystallization and orientation under shear. Infrared spectroscopy (FTIR) analysis showed there is no special chemical interaction between HDPE and AT, but shear induced significant changes on the material structure and properties. Differential scanning calorimetry (DSC) analysis showed strong nucleation effect by AT especially under shear. And more, shear will induce much better dispersion of AT in the DPIM sample vs. CIM. AT nanorods and lamellae of HDPE are more organized in the DPIM sample while there is only random distribution in the CIM sample. Most AT nanorods embed in the HDPE lamellae and form a brush-like hybrid structure due to shear. The shear-induced orientation will be enhanced with higher AT loading. The mechanical performance of the composites was significantly improved via DPIM.