Mixed phase silicon thin films grown at high rate using 60 MHz assisted VHF-PECVD technique

Mixed phase amorphous and nanocrystalline silicon (a-Si:H and nc-Si:H) thin films were deposited by VHF-PECVD (60 MHz) using Argon (Ar) as the diluent of silane. These amorphous and crystalline silicon thin films were deposited by varying the argon dilution (f_Ar) from 10–97.5% while keeping other process parameters constant. The effects of argon dilution on deposition rate, structural and optical properties of micro/nanocrystalline silicon thin films are studied. It has been observed that the films deposited from f_Ar 10–70% showed the deposition rate >20 Å/s with the highest deposition rate achieved of ~25 Å/s. Structural characterization has been performed by micro-Raman analysis and Atomic force microscopy. Raman shift towards higher wave number (515 cm⁻¹) with increase of f_Ar indicates variation in crystallinity of silicon films. HRTEM studies revealed the distribution of grain size and the degree of crystallinity. Optical absorption spectroscopy confirmed the increase in band gap of the materials from 1.5 to 2.1 eV.     

A study on phase transformation of SnOx thin films prepared by reactive magnetron sputtering

In the paper, SnO_x thin films were deposited by reactive magnetron sputtering from a tin target in O₂ containing working gas. The evolution from Sn-containing SnO to tetravalent SnO₂ films was investigated. The films could be classified into three groups according to their optical band gaps, which are E_g<2.5 eV, E_g=3.0–3.3 eV and E_g>3.7 eV. The electric measurements show that high conductivity can be obtained much easier in SnO₂ than in SnO films. A high electron mobility of 15.7 cm² V⁻¹ s⁻¹, a carrier concentration of 1.43×10²⁰ cm⁻³ and a resistivity of 2.8×10⁻³ Ω cm have been achieved in amorphous SnO₂ films. Films with the optical band gap of 3.0–3.3 eV remain amorphous though the substrate temperature is as high as 300 °C, which implies that °btaining high mobility in p-type SnO is more challenging in contrast to n-type SnO₂ films.     

Temperature effect on the physical properties of CuIn11S17 thin films for photovoltaic applications

CuIn₁₁S₁₇ compound was synthesized by horizontal Bridgman method using high-purity copper, indium and sulfur elements. CuIn₁₁S₁₇ thin films were prepared by high vacuum evaporation on glass substrates. The glass substrates were heated at 30, 100 and 200 °C. The structural properties of the powder and the films were investigated using X-ray diffraction (XRD). XRD analysis of thin films revealed that the sample deposited at a room temperature was amorphous in nature while those deposited on heated substrates were polycrystalline with a preferred orientation along the (311) plane of the spinel phase. Ultraviolet–visible (UV–vis) spectroscopy was used to study the optical properties of thin films. The results showed that CuIn₁₁S₁₇ thin films have high absorption coefficient α in the visible range (10⁵–10⁶ cm⁻¹). The band gap E_g of the films decrease from 2.30 to 1.98 eV with increasing the substrate temperature (T_s) from 30 to 200 °C. We exploited the models of Swanepoel, Wemple–DiDomenico and Spitzer–Fan for the analysis of the dispersion of the refractive index n and the determination of the optical constants of the films. Hot probe method showed that CuIn₁₁S₁₇ films deposited at T_s=30 °C and T_s=100 °C are p-type conductivity whereas the sample deposited at T_s=200 °C is highly compensated.     

Effect of processing parameter on structural,optical and electrical properties of photovoltaic chalcogenide nanostructured RF magnetron sputtered thin absorbing films

The aim of this work was to develop high quality of CuIn_1−xGa_xSe₂ thin absorbing films with x (Ga/In+Ga)<0.3 by sputtering without selenization process. CuIn_0.8Ga_0.2Se₂ (CIGS) thin absorbing films were deposited on soda lime glass substrate by RF magnetron sputtering using single quaternary chalcogenide (CIGS) target. The effect of substrate temperature, sputtering power & working pressure on structural, morphological, optical and electrical properties of deposited films were studied. CIGS thin films were characterised by X-ray diffraction (XRD), Field emission scanning electron microscope (FE-SEM), Energy dispersive X-ray spectroscopy (EDAX), Atomic force microscopy (AFM), UV–vis–NIR spectroscopy and four probe methods. It was observed that microstructure, surface morphology, elemental composition, transmittance as well as conductivity of thin films were strongly dependent on deposition parameters. The optimum parameters for CIGS thin films were obtained at a power 100 W, pressure 5 mT and substrate temperature 500 °C. XRD revealed that thin film deposited at above said parameters was polycrystalline in nature with larger crystallite size (32 nm) and low dislocation density (0.97×10¹⁵ lines m⁻²). The deposited film also showed preferred orientation along (112) plane. The morphology of the film depicted by FE-SEM was compact and uniform without any micro cracks and pits. The deposited film exhibited good stoichiometry (Ga/In+Ga=0.19 and In/In+Ga=0.8) with desired Cu/In+Ga ratio (0.92), which is essential for high efficiency solar cells. Transmittance of deposited film was found to be very low (1.09%). The absorption coefficient of film was ~10⁵ cm⁻¹ for high energy photon. The band gap of CIGS thin film evaluated from transmission data was found to be 1.13 eV which is optimum for solar cell application. The electrical conductivity (7.87 Ω⁻¹ cm⁻¹) of deposited CIGS thin film at optimum parameters was also high enough for practical purpose.     

Study of the correlation between structural and photoluminescence properties of CdSe thin films deposited by close-spaced vacuum sublimation

CdSe polycrystalline films were deposited by a close-spaced vacuum sublimation method at different substrate temperatures (T_s) using glass slides as substrates. At T_s≤673 K the films have a structure with strong dispersion of grain size (d) (from 0.1 to 0.3 μm). In this case the layer-by-layer mechanism determines the growth process of the layers. For T_s=873 K they have a columnar-like structure with a clear growth texture and the average grain size d=3–4 μm. The films obtained at T_s>473 K are n-type and only correspond to a single wurtzite phase. The crystallites are preferentially oriented with the (102) planes parallel to the substrate. At lower temperatures the films are bi-phase. The microstress level in CdSe films obtained at Т_s=873 K (0.5×10⁻³) is considerably smaller than for the films deposited at Т_s=773 K (4.0×10⁻³). Increase of the value of T_s improves the stoichiometry of CdSe films. Analysis of the low-temperature photoluminescence (PL) spectra let us determine the nature and energy of point and extended defects in the investigated films. It was shown that the films contain Na(Li) and P residual impurities. The results of the structural and PL measurements showed that the CdSe polycrystalline films are of fairly good crystal and optical quality for T_s=873 K and can be suitable for various applications.     

Development of highly conducting n-type micro-crystalline silicon oxide thin film and its application in high efficiency amorphous silicon solar cell

Wide band gap and highly conducting n-type nano-crystalline silicon film can have multiple roles in thin film solar cell. We prepared phosphorus doped micro-crystalline silicon oxide films (n-μc-SiO:H) of varying crystalline volume fraction (X_c) and applied some of the selected films in device fabrication, so that it plays the roles of n-layer and back reflector in p-i-n type solar cells. It is generally understood that a higher hydrogen dilution is needed to prepare micro-crystalline silicon, but in case of the n-μc-SiO:H an optimized hydrogen dilution was found suitable for higher X_c. Observed X_c of these films mostly decreased with increased plasma power (for pressure<2.0 Torr), increased gas pressure, flow rate of oxygen source gas and flow rates of PH₃>0.08 sccm. In order to determine deposition conditions for optimized opto-electronic and structural characteristics of the n-μc-SiO:H film, the gas flow rates, plasma power, deposition pressure and substrate temperature were varied. In these films, the X_c, dark conductivity (σ_d) and activation energy (E_a) remained within the range of 0–50%, 3.5×10⁻¹⁰ S/cm to 9.1 S/cm and 0.71 eV to 0.02 eV, respectively. Low power (30 W) and optimized flow rates of H₂ (500 sccm), CO₂ (5 sccm), PH₃ (0.08 sccm) showed the best properties of the n-μc-SiO:H layers and an improved performance of a solar cell. The photovoltaic parameters of one of the cells were as follows, open circuit voltage (V_oc), short circuit current density (J_sc), fill-factor (FF), and photovoltaic conversion efficiency (η) were 950 mV, 15 mA/cm², 64.5% and 9.2% respectively.     

Substrate temperature effect on structural,optical and electrical properties of vacuum evaporated SnO2 thin films

Tin oxide (SnO₂) thin films were deposited on glass substrates by thermal evaporation at different substrate temperatures. Increasing substrate temperature (T_s) from 250 to 450 °C reduced resistivity of SnO₂ thin films from 18×10⁻⁴ to 4×10⁻⁴▒ Ω ▒cm. Further increase of temperature up to 550 °C had no effect on the resistivity. For films prepared at 450 °C, high transparency (91.5%) over the visible wavelength region of spectrum was obtained. Refractive index and porosity of the layers were also calculated. A direct band gap at different substrate temperatures is in the range of 3.55−3.77 eV. X-ray diffraction (XRD) results suggested that all films were amorphous in structure at lower substrate temperatures, while crystalline SnO₂ films were obtained at higher temperatures. Scanning electron microscopy images showed that the grain size and crystallinity of films depend on the substrate temperature. SnO₂ films prepared at 550 °C have a very smooth surface with an RMS roughness of 0.38 nm.     

A facile chemical reduction approach for effectively tuning thermoelectric properties of PEDOT films

Poly(3,4-ethylenedioxythiophene)–tosylate–polyethylene glycol–polypropylene glycol–polyethylene glycol (PEDOT–Tos–PPP) films were prepared via a vapor phase polymerization (VPP) method. The films possess good electrical conductivity (1550 S cm⁻¹), low Seebeck coefficient (14.9 μV K⁻¹) and thermal conductivity (0.501 W m⁻¹ K⁻¹), and ZT ∼ 0.02 at room temperature (RT, 295 K). Then, the films were treated with NaBH₄/DMSO solutions of different NaBH₄ concentrations to adjust the redox level. After the NaBH₄/DMSO treatment (dedoping), the electrical conductivity of the films continuously decreased from 1550 to 5.7 S cm⁻¹, whereas the Seebeck coefficient steeply increased from 14.9 to 143.5 μV K⁻¹. A maximum power factor of 98.1 μW m⁻¹ K⁻² has been achieved at an optimum redox level. In addition, the thermal conductivity of the PEDOT–Tos–PPP films decrease from 0.501 to 0.451 W m⁻¹ K⁻¹ after treated with 0.04% NaBH₄/DMSO solution. A maximum ZT value of 0.064 has been achieved at RT. The electrical conductivity and thermal conductivity (Seebeck coefficient) of the untreated and 0.04% NaBH₄/DMSO treated PEDOT–Tos–PPP films decrease (increases) with increasing temperature from 295 to 385 K. And the power factor of the films monotonically increases with temperature. The ZT at 385 K of the 0.04% NaBH₄/DMSO treated film is 0.155.     

Effects of RTA temperatures on conductivity and micro-structures of boron-doped silicon nanocrystals in Si-rich oxide thin films

In this work, the B-doped Si rich oxide (SRO) thin films were deposited and then annealed using rapid thermal annealing (RTA) to form SiO₂-matrix silicon nanocrystals (Si NCs). The effects of the RTA temperatures on the structural properties, conduction mechanisms and electrical properties of B-doped SRO thin films (BSF) were investigated systematically using Hall measurements, Fourier transform infrared spectroscopy and Raman spectroscopy. Results showed that the crystalline fraction of annealed BSF increased from 41.3% to 62.8%, the conductivity was increased from 4.48×10⁻³ S/cm to 0.16 s/cm, the carrier concentration was increased from 8.74×10¹⁷ cm⁻³ to 4.9×10¹⁸ cm⁻³ and the carrier mobility was increased from 0.032 cm² V⁻¹ s⁻¹ to 0.2 cm² V⁻¹ s⁻¹ when the RTA temperatures increased from 1050 °C to 1150 °C. In addition, the fluctuation induced tunneling (FIT) theory was applicable to the conduction mechanisms of SiO₂-matrix boron-doped Si-NC thin films.     

Properties of fluorine-doped tin oxide films prepared by an improved sol-gel process

Fluorine-doped tin oxide (FTO) films were prepared by an improved sol-gel process, in which FTO films were deposited on glass substrates using evaporation method, with the precursors prepared by the conventional sol-gel method. The coating and sintering processes were combined in the evaporation method, with the advantage of reduced probability of films cracking and simplified preparation process. The effects of F-doping contents and structure of films on properties of films were analyzed. The results showed the performance index (Φ_TC=3.535×10⁻³ Ω⁻¹ cm) of the film was maximum with surface resistance (R_sh) of 14.7 Ω cm⁻¹, average transmittance (T) of 74.4% when F/Sn=14 mol%, the reaction temperature of the sol was 50 °C, and the evaporation temperature was 600 °C in muffle furnace, and the film has densification pyramid morphology and SnO_2−xF_x polycrystalline structure with tetragonal rutile phase. Compared with the commercial FTO films (Φ_TC=3.9×10⁻³ Ω⁻¹ cm, R_sh=27.4 Ω cm⁻¹, T=80%) produced by chemical vapor deposition (CVD) method, the Φ_TC value of FTO films prepared by an improved sol-gel process is close to them, the electrical properties are higher, and the optical properties are lower.     

Effect of substrate temperature on structural,morphological, optical and electrical properties of MnIn2S4 thin films prepared by nebulizer spray pyrolysis technique

Manganese indium sulphide (MnIn₂S₄) thin films were deposited using an aqueous solution of MnCl₂, InCl₃ and (NH₂)₂CS in the molar ratio 1:2:4 by simple chemical spray pyrolysis technique. The thin film substrates were annealed in the temperature range between 250 and 350 °C to study their various physical properties. The structural properties as studied by X-ray diffraction showed that MnIn₂S₄ thin films have cubic spinel structure. The formation of cube and needle shaped grains was clearly observed from FE-SEM analysis. The energy dispersive spectrum (EDS) predicts the presence of Mn, In and S in the synthesized thin film. From the optical studies, it is analyzed that the maximum absorption co-efficient is in the order between 10⁴ and 10⁵ cm⁻¹ and the maximum transmittance (75%) was noted in the visible and infrared regions. It is noted that, the band gap energy decreases (from 3.20 to 2.77 eV) with an increase of substrate temperature (from 250 to 350 °C). The observations from photoluminescence studies confirm the emission of blue, green, yellow and red bands which corresponds to the wavelength range 370–680 nm. Moreover, from the electrical studies, it is observed that, as the substrate temperature increases the conductivity also increases in the range 0.29–0.41×10⁻⁴ Ω⁻¹ m⁻¹. This confirms the highly semiconducting nature of the film. The thickness of the films was also measured and the values ranged between 537 nm (250 °C) to 483 nm (350 °C). This indicates that, as the substrate temperature increases, the thickness of the film decreases. From the present study, it is reported that the MnIn₂S₄ thin films are polycrystalline in nature and can be used as a suitable ternary semiconductor material for photovoltaic applications.     

Investigation of optical and chemical bond properties of hydrogenated amorphous silicon nitride for optoelectronics applications

The aim of this work is to determine optimal deposition parameters of silicon nitride for optical applications. The authors present the investigation of hydrogenated amorphous silicon nitride SiN_x:H deposited by the low temperature PECVD method in high frequency reactors. The study of hydrogen bonds in the SiN_x:H thin films were detailed. The impact of NH₃, SiH₄ and N₂ flow ratio and radio frequency power on optical coefficients in relation to chemical composition and roughness of the film is studied. The correlation between chemical bonds (N–H, Si–H) and refractive index and extinction coefficients is systematically verified. The experimental results show that the films with high refractive indexes superior to 2.05 and low roughness of about 0.35 nm can be achieved for optoelectronics applications by tuning the flow ratio or decreasing the RF power. A variety of processes have been suggested as compatible with low thermal budget (under 350 °C) in order to integrate optical waveguides with lower loss. In particular, the incorporation of N₂ as dilution gas is suited to the fabrication of SiN_x:H films optical waveguide requiring low N–H bonds, low concentration of hydrogen [H] and high refractive index.     

Effect of the film thickness on the crystal structure and ferroelectric properties of (Hf0.5Zr0.5)O2 thin films deposited on various substrates

In this work, the effect of the film thickness on the crystal structure and ferroelectric properties of (Hf_0.5Zr_0.5)O₂ thin films was investigated. The thin films were deposited on (111) Pt-coated SiO₂, Si, and CaF₂ substrates with thermal expansion coefficients of 0.47, 4.5, and 22×10⁻⁶/°C, respectively. From the X-ray diffraction measurements, it was found that the (Hf_0.5Zr_0.5)O₂ thin films deposited on the SiO₂ and CaF₂ substrates experienced in-plane tensile and compressive strains, respectively, in comparison with the films deposited on the Si substrates. For films deposited on all three substrates, the volume fraction of the monoclinic phase increased with increasing film thickness, with the SiO₂ substrate having the lowest monoclinic phase volume fraction at all film thicknesses tested. The grain size of the films, which is an important factor for the formation of the ferroelectric phase, remained almost constant at about 10 nm in diameter regardless of the film thickness and type of substrate utilized. Ferroelectricity was observed for the 17 nm-thick films deposited on SiO₂ and Si substrates, and the maximum remanent polarization (P_r) value of 9.3 µC/cm² was obtained for films deposited on the SiO₂ substrate. In contrast, ferroelectricity with P_r=4.4 µC/cm² was observed only for film on SiO₂ substrate in case of 55 nm-thick films. These results suggest that the films under in-plane tensile strain results in the larger ferroelectricity for 17 nm-thick films and have a ferroelectricity up to 55 nm-thick films.     

Low power flexible organic thin film transistors with amorphous Ba0.7Sr0.3TiO3 gate dielectric grown by pulsed laser deposition at low temperature

We deposited amorphous Ba_0.7Sr_0.3TiO₃ (BST) on silicon and plastic substrate under 110 °C by pulsed laser deposition (PLD) and use it as the dielectric of the organic transistor. Depends on the thickness of BST layer, the highest mobility of the devices can achieve 1.24 cm² V^?1 s^?1 and 1.01 cm² V^?1 s^?1 on the silicon and polyethylene naphthalate (PEN) substrate, respectively. We also studied the upward and downward bending tests on the transistors and the dielectric thin films. We found that the BST dielectric pentacene transistor can maintain the mobility at 0.5 cm² V^?1 s^?1 or higher while the bending radius is around 3 mm in both upward and downward bending. Our finding demonstrates the potential application of PLD growth high-k dielectric in the large area organic electronics devices.     

Consequences of twisting the aromatic core of N,N′-dimethylperylene-3,4,9,10-biscarboximide by chemical substitution for the electronic coupling and electric transport in thin films

Thin films of 1,6,7,12-tetrachloro-N,N^′-dimethylperylene-3,4,9,10-biscarboximide (Cl₄MePTCDI) prepared by physical vapor deposition (PVD) were compared to thin films of the unchlorinated N,N^′-dimethylperylene-3,4,9,10-biscarboximide (MePTCDI) to investigate the influence of a changed molecular structure on the electrical properties of the materials. The films were prepared on microstructured Si/SiO₂ substrates with interdigitated Au electrode arrays of 2 μm electrode distance or on quartz glass with electrode distances in the mm range. The films were investigated by conductance measurements, thermoelectric power, electric field effect, ultraviolet photoelectron spectroscopy (UPS) and atomic force microscopy (AFM). The thickness-dependence of the conductance measured during film growth (in situ) indicated a growth mode in islands (Volmer-Weber), which was confirmed by subsequent AFM. As expected, Cl₄MePTCDI was characterized as an organic n-type semiconductor. Charge transport occurred by a hopping mechanism as revealed by temperature-dependent thermopower and field-effect measurements. Effective electron mobilities at room temperature were found around 10⁻⁵ cm² V ⁻¹ s⁻¹ considerably lower than the values for MePTCDI. A rather constant concentration of mobile electrons of (1–2) × 10¹⁸ cm⁻³ was determined for both materials. The morphology of Cl₄MePTCDI islands indicated amorphous growth as opposed to crystals obtained for MePTCDI, as also revealed earlier by optical spectroscopy and the role of crystallinity in the electrical conduction is discussed.     

Direct synthesis of quaternary Cd(Zn,S)Se thin films: Effects of composition

In the present communication, the binary CdSe and quaternary Cd_1-xZn_xSe_1-yS_y (0 ≤ x = y ≤ 0.35) thin films were synthesized using a chemical bath deposition. Thin film deposition was carried out at the optimized conditions (pH = 10 ± 0.1, deposition temperature = 70 ± 0.1 °C, deposition time = 100 min and substrate rotation speed = 65 ± 2 rpm). X-ray diffraction studies confirmed hexagonal-wurtzite crystal structure with the formation of quaternary Cd(Zn, S)Se phase along with binary CdSe, CdS, ZnS and ZnSe, phases of the as-grown Cd_1-xZn_xSe_1-yS_y thin films. Elemental analysis showed presence of Cd²⁺, Zn²⁺, S^2- and Se^2- in the deposited films. Fourier transform infrared spectroscopy shown the bands at 911.15 cm⁻¹ – 901.62 cm⁻¹ which are assigned to the stretching frequency of Cd–Se bond. Scanning electron microscopy show transformation of the microstructure from globular crystallites to a rhomboid flake like network. The electrical conductivity was typically ≈ 10⁻⁷ Ω⁻¹ cm⁻¹. At low temperatures, the conduction was by variable range hopping, and this changed to thermally activated grain boundary dominated conduction for T > 350 K.     

Evaporated iron disulfide thin films with sulfurated annealing treatments

FeS₂ thin films were grown on a glass substrate using a physical vapor deposition technique at room temperature. Subsequently, the thin films were annealed in two different atmospheres: vacuum and vacuum-sulfur. In the vacuum-sulfur atmosphere a graphite box was used as sulfur container and the films were sulfurated successfully at 200–350 ºC. It was found that annealing in a vacuum-sulfur atmosphere was indispensable in order to obtain polycrystalline FeS₂ thin films. The polycrystalline nature and pure phase were determined by XRD and Raman techniques and the electrical properties by the Hall effect. Using the sulfurating technique, the n-type semiconductor was prepared at 200–350 °C and a p-type at 500 °C. The carrier concentrations were between 1.19×10²⁰ and 2.1×10²⁰ cm⁻³. The mobility was 9.96–5.25 cm² V⁻¹ s⁻¹ and the resistivity was 6.31×10⁻² to 1.089×10⁻² Ω cm. The results obtained from EDS showed that the films prepared in the vacuum-sulfur atmosphere were close to stoichiometric and that the indirect band gap varied between 1.03 and 0.945 eV.     

Thickness-dependent optoelectronic properties of CuCr0.93Mg0.07O2 thin films deposited by reactive magnetron sputtering

CuCr_0.93Mg_0.07O₂ thin films were successfully deposited by DC reactive magnetron sputtering at 1123 K from metallic targets. The influence of film thickness on the structural and optoelectronic properties of the films was investigated. X-ray diffraction (XRD) results revealed that all the films had a delafossite structure with no other phases. The optical and electrical properties were investigated by UV–VIS spectrophotometer and Hall measurement, respectively. It was found that the optoelectronic properties exhibited a thickness-dependent behavior. The optical band gap and the average transmittance of the films showed a monotonous decrease with respect to the increase in thickness. The average transmittance in the visible region decreased from 67% to 47% as the thickness increased from ~70 nm to ~280 nm. Simultaneously, the conductivity of the films fell from 1.40 S∙cm⁻¹ to 0.27 S∙cm⁻¹. According to Haacke's figure of merit (FOM), a film with a maximum FOM value of about 1.72×10⁻⁷ Ω⁻¹ can be achieved when the thickness is about 70 nm (σ≈ 1.40 S·cm⁻¹ and T_av. ≈67%).     

Properties of fluorine-doped SnO2 thin films by a green sol–gel method

Fluorine doped tin oxide (FTO) films were fabricated on a glass substrate by a green sol–gel dip-coating process. Non-toxic SnF₂ was used as fluorine source to replace toxic HF or NH₄F. Effect of SnF₂ content, 0–10 mol%, on structure, electrical resistivity, and optical transmittance of the films were investigated using X-ray diffraction, Hall effect measurements, and UV–vis spectra. Structural analysis revealed that the films are polycrystalline with a tetragonal crystal structure. Grain size varies from 43 to 21 nm with increasing fluorine concentration, which in fact critically impacts resultant electrical and optical properties. The 500 °C-annealed FTO film containing 6 mol% SnF₂ shows the lowest electrical resistivity 7.0×10⁻⁴ Ω cm, carrier concentration 1.1×10²¹ cm⁻³, Hall mobility 8.1 cm²V⁻¹ s⁻¹, optical transmittance 90.1% and optical band-gap 3.91 eV. The 6 mol% SnF₂ added film has the highest figure of merit 2.43×10⁻² Ω⁻¹ which is four times higher than that of un-doped FTO films. Because of the promising electrical and optical properties, F-doped thin films prepared by this green process are well-suited for use in all aspects of transparent conducting oxide.     

Influence of working pressure on the structural,optical and electrical properties of sputter deposited AZO thin films

Highly oriented crystalline aluminum doped zinc oxide (AZO) films were sputter deposited on glass substrates and a systematic investigation on the as deposited and etched films was reported for its further application in silicon thin film solar cell. Influence of the deposition pressure (from 2 to 8 mTorr) and post-annealing temperature (at 400 °C for 5 min) on the structural, optical and electrical properties of the as-deposited and etched samples were analyzed. The optimum condition for its reproducibility and large area deposition is determined and found that the depositions made at 8 mTorr at 200 W having the distance from source to substrate of 9 cm. All the AZO films exhibited a c-axis preferred orientation perpendicular to the substrate and their crystallinity was improved after annealing. From the XRD pattern the grain size, stress and strain of the films were evaluated and there is no drastic variation. Optical transmittance, resistivity, Hall mobility and carrier concentration for the as deposited and etched-annealed films were found to improve from 79 to 82%; 2.97 to 3.14×10⁻⁴ Ω cm; 25 to 38 cm²/V s; 8.39 to 5.96×10²⁰/cm³ respectively. Based on the triangle diagram between figure of merit and Hall mobility, we obtained a balance of point between the electrical and optical properties to select the deposition condition of film for device application.