Preparation of CexZr1−xO2 (x = 0.75, 0.62) solid solution and its application in Pd-only three-way catalysts

Nanoparticles of Ce_xZr_1−xO₂ (x = 0.75, 0.62) were prepared by the oxidation-coprecipitation method using H₂O₂ as an oxidant, and characterized by N₂ adsorption, XRD and H₂-TPR. Ce_xZr_1−xO₂ prepared had single fluorite cubic structure, good thermal stability and reduction property. With the increasing of Ce/Zr ratio, the surface area of Ce_xZr_1−xO₂ increased, but thermal stability of Ce_xZr_1−xO₂ decreased. The surface area of Ce_0.62Zr_0.38O₂ was 41.2 m²/g after calcination in air at 900 °C for 6 h. TPR results showed the formation of solid solution promoted the reduction of CeO₂, and the reduction properties of Ce_xZr_1−xO₂ were enhanced by the cycle of TPR-reoxidation. The Pd-only three-way catalysts (TWC) were prepared by the impregnation method, in which Ce_0.75Zr_0.25O₂ was used as the active washcoat and Pd loading was 0.7 g/L. In the test of Air/Fuel, the conversion of C₃H₈ was close to 100% and NO was completely converted at λ < 1.025. The high conversion of C₃H₈ was induced by the steam reform and dissociation adsorption reaction of C₃H₈. Pd-only catalyst using Ce_0.75Zr_0.25O₂ as active washcoat showed high light off activity, the reaction temperatures (T₅₀) of 50% conversion of CO, C₃H₈ and NO were 180, 200 and 205 °C, respectively. However, the conversions of C₃H₈ and NO showed oscillation with continuously increasing the reaction temperature. The presence of La₂O₃ in washcoat decreased the light off activity and suppressed the oscillation of C₃H₈ and NO conversion. After being aged at 900 °C for 4 h, the operation windows of catalysts shifted slightly to rich burn. The presence of La₂O₃ in active washcoat can enhance the thermal stability of catalyst significantly.     

Regeneration of thermally aged Pt-Rh/CexZr1−xO2-Al2O3 model three-way catalysts by oxychlorination treatments

Pt-Rh/Ce_xZr_1−xO₂-Al₂O₃ with 0.6 and 1.0 wt.% noble metal loadings were prepared and characterized for their metal dispersion with respect to Ce_xZr_1−xO₂-free Pt-Rh/Al₂O₃ in fresh, thermally aged and oxychlorinated states. Thermal ageing at 973 K led to loss of metal dispersion in all cases but to negligible effect on the dispersion of the Ce_xZr_1−xO₂ component where present. Oxychlorination was able to fully recover metal dispersion in all cases but led to different effects on the redox properties of Ce_xZr_1−xO₂ which appeared to be related to the metal loadings. Despite showing improved dispersion following regeneration, higher loaded catalyst showed no improvement in light-off performance for either NO reduction or CO oxidation and showed poorer oxygen storage (OSC) ability, particularly at higher temperatures. Lower loaded catalyst showed improved dispersion, improved OSC and reduced light-off temperatures for NO reduction and CO oxidation after oxychlorination compared to that in the thermally aged state.     

A correlation between crystal structure and catalytic activity in the solid solutions CdMoxW1−xO4

Two CdMo_xW_1−xO₄ solid solutions with the scheelite and the wolframite structures were synthesised via different techniques and their structures were determined from powder refinements. The limit of the reciprocal solubility of Mo in CdWO₄ has been checked. Several compositions of the solid solutions have been tested in the catalytic mild oxidation of propane or propene and relations between the structures and the catalytic activity are proposed.     

Ce1−xCuxO2−x/Al2O3/FeCrAl catalysts for catalytic combustion of methane

A series of the Ce_1−xCu_xO_2−x/Al₂O₃/FeCrAl catalysts (x = 0–1) were prepared. The structure of the catalysts was characterized using XRD, SEM and H₂-TPR. The catalytic activity of the catalysts for the combustion of methane was evaluated. The results indicated that in the Ce_1−xCu_xO_2−x/Al₂O₃/FeCrAl catalysts the surface phase structure were the Ce_1−xCu_xO_2−x solid solution, -Al₂O₃ and γ-Al₂O₃. The surface particle shape and size were different with the variety of the molar ratio of Ce to Cu in the Ce_1−xCu_xO_2−x solid solution. The Cu component of the Ce_1−xCu_xO_2−x/Al₂O₃/FeCrAl catalysts played an important role to the catalytic activity for the methane combustion. There were the stronger interaction among the Ce_1−xCu_xO_2−x solid solution and the Al₂O₃ washcoats and the FeCrAl support.     

Effect of ceria–zirconia ratio on the interaction of CO with PdO/Al2O3–(Cex–Zr1−x)O2 catalysts prepared by sol–gel method

The current work is devoted to study of CO interaction with PdO/Al₂O₃–(Ce_x–Zr_1−x)O₂ catalysts. Ceria–zirconia–alumina supports with different Ce/Zr ratio were prepared by sol–gel technique. The FT-IR characterization of CO adsorbed at −120 and 25 °C on oxidized and reduced samples revealed that Ce/Zr ratio modifies the surface properties of support and oxidation state of palladium. The catalyst with Ce/Zr molar ratio 0.5/0.5 was characterized with the highest ability to stabilize palladium in oxide state and the highest activity to oxidize CO. Redox treatment of catalysts improves their catalytic activity.     

Electrical resistivity and thermopower of (La1−xSrx)MnO3 and (La1−xSrx)CoO3 at elevated temperatures

Electrical resistivity and Seebeck (S) measurements were performed on (La_1−xSr_x)MnO₃ (0.02x0.50) and (La_1−xSr_x)CoO₃ (0x0.15) in air up to 1073 K. (La_1−xSr_x)MnO₃ (x0.35) showed a metal-to-semiconductor transition; the transition temperature almost linearly increased from 250 to 390 K with increasing Sr content. The semiconductor phase above the transition temperature showed negative values of S. (La_1−xSr_x)CoO₃ (0x0.10) showed a semiconductor-to-metal transition at 500 K. Dominant carriers were holes for the samples of x0.02 above room temperature. LaCoO₃ showed large negative values of S below ca. 400 K, indicative of the electron conduction in the semiconductor phase.     

A thermogravimetric and FT-IR study of the reduction by H2 of sulfated Pt/CexZr1−xO2 solids

The nature, concentration and reducibility by H₂ of sulfate species formed from SO₂ oxidation were studied over a range of Pt/Ce_xZr_1−xO₂ catalysts using infrared spectroscopy and thermogravimetry. Ionic sulfates were formed over ceria and Ce-containing catalysts, even at high Zr content. The sample-specific surface area, the presence of platinum and the zirconium proportion affected the rate and extent of formation of sulfate in the bulk of the materials. Sulfate reduction by H₂ first occurred at the Ce_xZr_1−xO₂ surface. Bulk-like S-containing species subsequently migrated towards the surface to continuously replace surface sulfates removed by the reduction. The temperature required for sulfate migration as well as that necessary for sulfate reduction increased with the Zr content. The amount of stored sulfur is closely linked to the specific surface area of the sample. Finally, we have clearly shown that thermogravimetry was an appropriate technique for evaluating the oxygen storage capacity (OSC) of sulfated ceria–zirconia mixed oxides, despite the additional complexity due to the presence of sulfate compounds and various reduced S-species that can be formed during sample reduction.     

Catalytic oxidation of nitrogen monoxide over La1−xCexCoO3 perovskites

This paper presents an investigation on the NO oxidation properties of perovskite oxides. La_1−xCe_xCoO₃ (x = 0, 0.05, 0.1, 0.2, 0.3, 0.4) perovskite-type oxides were synthesized through a citrate method and characterized by XRD, BET and XPS. The catalytic activities were enhanced significantly with Ce substitution, and achieved the best when x was 0.2, but decreased at higher x values. The performed characterizations reveal that the adsorbed oxygen on the surface plays an important role in the oxidation of NO into NO₂. The surface compounds after the co-adsorption of NO and O₂ at room temperature, were investigated by DRIFTS and TPD experiments. Three species: the bridging nitrate, the hyponitrites and the monodentate nitrate, were formed on the surface. The order of thermal stabilities was as follows: monodentate > hyponitrite > bridging. Among them, only the monodentate nitrate which decomposed at above 300 °C, would desorb NO₂ into the gas phase. When Ce was added, the temperature of monodentate nitrate desorption became low and the adsorption of the other two species decreased. This might be related to the oxidation state of Co on the surface. Analysis by synthesizing the characterization results and catalytic activity data shows that large amounts of adsorbed oxygen, small amount of inactive compounds on the surface and low NO₂ desorption temperature are favorable for the oxidation of NO.     

Synthesis and properties of Bi0.5(Na1−x−yKxAgy)0.5TiO3 lead-free piezoelectric ceramics

Bi_0.5(Na_1−x−yK_xAg_y)_0.5TiO₃ piezoelectric ceramics were prepared by conventional ceramic processes. X-ray diffraction patterns show a pure perovskite structure, indicating that the K⁺ and Ag⁺ ions substitute for the Na⁺ ions in Bi_0.5Na_0.5TiO₃. The temperature dependence of the dielectric constant and dissipation factor shows all ceramics to experience two phase transitions: from ferroelectric to anti-ferroelectric and from anti-ferroelectric to paraelectric. The transition temperature from ferroelectric to anti-ferroelectric and the temperature at which the dielectric constant reaches its maximum value decrease with the increase of K⁺ amount. At room temperature, the ceramics containing 17.5–20 mol% K⁺ and 2 mol% Ag⁺ exhibit high piezoelectric constant (d₃₃ = 180 pC/N) and high electromechanical coupling factor (k_p = 35%).     

Electronic and structural properties of SnxTi1−xO2 solid solutions: a periodic DFT study

The structural and electronic properties of selected compositions of Sn_xTi_1−xO₂ solid solutions (x=0, 1/24, 1/16, 1/12, 1/8, 1/6, 1/4, 1/2, 3/4, 5/6, 7/8, 11/12, 15/16, 23/24 and 1) were investigated by means of periodic density functional theory (DFT) calculations at B3LYP level. The calculations show that the corresponding lattice parameters vary non-linearly with composition, supporting positive deviations from Vegard’s law in the Sn_xTi_1−xO₂ system. Our results also account for the fact that chemical decomposition in Sn_xTi_1−xO₂ system is dominated by composition fluctuations along [0 0 1] direction. A nearly continuous evolution of the direct band gap and the Fermi level with the growing value of x is predicted. Ti 3d states dominate the lower portion of the conduction band of Sn_xTi_1−xO₂ solid solutions. Sn substitution for Ti in TiO₂ increases the oxidation–reduction potential of the oxide as well as it renders the lowest energy transition to be indirect. These two effects can be the key factors controlling the rate for the photogenerated electron–hole recombination. These theoretical results are capable to explain the enhancement of photoactivity in Sn_xTi_1−xO₂ solid solutions.     

Superiority of nitrate decomposition method for synthesis of K2NiF4-type LaxSr2−xMnO4 catalysts

K₂NiF₄-type La_0.2Sr_1.8MnO₄ was synthesized by nitrate (ND) and nitrate/acetate (NAD) decomposition methods as well as solid-state reaction. Single-phase oxide was obtained at 550 °C by the ND method just after the decomposition of Sr(NO₃)₂ and at 1000 °C by the NAD method after the decomposition of SrCO₃. The K₂NiF₄-type oxide was hardly formed by the solid-state reaction. In the La–Sr–Mn system, an intermediate compound of SrCO₃, if present or formed during the decomposition process, interfered with the low-temperature formation of the K₂NiF₄-type oxide because of its high decomposition temperature about 1000 °C. The ND method used only metal nitrates and no starting materials with carbon source, so that the low-temperature synthesis of the K₂NiF₄-type oxide was realized without forming obstinate intermediate compound of SrCO₃. The low-temperature synthesis was possible for La_xSr_2−xMnO₄ with the substitution of La (0 < x < 0.5) and not for La_0.2A_1.8MnO₄ (A = Ca and Ba). The effect of A-site cations on the K₂NiF₄-phase formation was discussed from the geometric aspect.     

Study of IrxRu1−xO2 oxides as anodic electrocatalysts for solid polymer electrolyte water electrolysis

Electrocatalysts of the general formula Ir_xRu_1−xO₂ were prepared using Adams’ fusion method. The crystallite characterization was examined via XRD, and the electrochemical properties were examined via cyclic voltammetry (CV) in, linear sweep voltammetry (LSV) and chronopotentiometry measurements in 0.5 M H₂SO₄. The electrocatalysts were applied to a membrane electrode assembly (MEA) and studied in situ in an electrolysis cell through electrochemical impedance spectroscopy (EIS) and stationary current density–potential relations were investigated. The Ir_xRu_1−xO₂ (x = 0.2, 0.4, 0.6) compounds were found to be more active than pure IrO₂ and more stable than pure RuO₂. The most active electrocatalyst obtained had a composition of Ir_0.2Ru_0.8O₂. With an Ir_0.2Ru_0.8O₂ anode, a 28.4% Pt/C cathode and the total noble metal loading of 1.7 mg cm⁻², the potential of water electrolysis was 1.622 V at 1 A cm⁻² and 80 °C.     

Ho-doped BaTiO3: Polymorphism, phase equilibria and dielectric properties of BaTi1−xHoxO3−x/2: 0 ≤ x ≤ 0.17

An extensive range of Ho-doped BaTiO₃ solid solution forms in which Ho substitutes for Ti with creation of oxygen vacancies. The effect of Ho substitution is to destabilise thermodynamically the high-temperature hexagonal polymorph of BaTiO₃. Nevertheless, at high Ho contents, the hexagonal polymorph forms as a kinetically stable intermediate before transforming to the thermodynamically stable cubic polymorph; its formation represents an example of Ostwald's rule of successive reactions. Samples fired at 1400 °C and cooled in air are insulating and transform from ferroelectric to relaxor ferroelectric behaviour with increasing x.     

Synthesis and characterization of Li ion conducting La2/3−xLi3xTiO3 by a polymerizable complex method

Ultrafine lithium ion conducting La_2/3−xLi_3xTiO₃ (x = 0.11, LLT) powder was synthesized by a simple polymerizable complex method based on the Pechini-type process. The formation mechanism, homogeneity and microstructure of the samples were investigated by thermal analysis (TG/DTA), X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). XRD analysis indicated the formation of pure perovskite-type phase. The powder synthesized at a temperature as low as 900 °C in a much shorter time than solid-state reaction method was well crystallized. The lithium ion conductivity of the LLT ceramics sintered at 1200 °C was found to be 9 × 10⁻⁴ S/cm at room temperature.     

Self-assembly of BixTi1−xO2 visible photocatalyst with core–shell structure and enhanced activity

Mesoporous Bi_xTi_1−xO₂ spheres with core–shell chamber were prepared by alcoholysis under solvothermal conditions. The cross-condensation between Ti–OH and Bi–OH ensured complete incorporation of Bi-dopants into TiO₂ lattice, though Bi atom is much bigger than Ti. Meanwhile, the aggregation of titania building clusters into spheres and their subsequent reactions including dissolution and re-deposition processes lead to the hollow spheres with tunable interior structure. The Bi-doping induced strong spectral response in visible region owing to the formation of narrow intermediate energy band gaps. Meanwhile, multiple reflections within the sphere interior voids promoted the light absorbance. As a result, the as-prepared Bi_xTi_1−xO₂ spheres exhibited much higher activity than the undoped TiO₂, the Bi₂O₃/TiO₂ obtained by impregnating the TiO₂ with Bi(NO₃)₃ solution, and the Bi_xTi_1−xO₂ after being ground during photodegradation of p-chlorophenol under visible light irradiation. Meanwhile, the Bi_xTi_1−xO₂ could be used repetitively for 10 times owing to the high hydrothermal stability and the absence of Bi-leaching.     

Adsorption of NO and NO2 on ceria–zirconia of composition Ce0.69Zr0.31O2: A DRIFTS study

In this study, the nature of surface intermediates generated by adsorption of NO and NO₂ on a commercial ceria–zirconia powder of composition Ce_0.69Zr_0.31O₂ was investigated using Diffuse Reflectance Infrared Fourier Transform Spectroscopy (DRIFTS). The conditions of occurrence of the main adsorbed species, i.e. nitrites and nitrates, are studied semi-quantitatively as a function of catalyst pre-treatment and/or type of adsorbed NO_x molecule. On the partially reduced ceria–zirconia, the primary role of NO_x is to re-oxidize the surface via adsorption/decomposition on reduced sites. By contrast, the formation of nitrites and nitrates readily occurs on oxidized surfaces, the latter kind of species being strongly promoted in the case of NO₂ adsorption only.     

Thermoelectric characterization of NaxMx/2Ti1−x/2O2 (M=Co, Ni and Fe) polycrystalline materials

Layered -titanate materials, Na_xM_x/2Ti_1−x/2O₂ (M=Co, Ni and Fe, x=0.2–0.4), were synthesized by flux reactions, and electrical properties of polycrystalline products were measured at 300–800 °C. After sintering at 1250 °C in Ar, all products show n-type thermoelectric behavior. The values of both d.c. conductivity and Seebeck coefficient of polycrystalline Na_0.4Ni_0.2Ti_0.8O₂ were ca. 7×10³ S/m and ca. −193 μV/K around 700 °C, respectively. The measured thermal conductivity of layered -titanate materials has lower value than conductive oxide materials. It was ca. 1.5 Wm⁻¹ K⁻¹ at 800 °C. The estimated thermoelectric figure-of-merit, Z, of Na_0.4Ni_0.2Ti_0.8O₂ and Na_0.4Co_0.2Ti_0.8O₂ was about 1.9×10⁻⁴ and 1.2×10⁻⁴ K⁻¹ around 700 °C, respectively.     

Crystalline structure and electrical properties of YCuxMn1–xO3 solid solutions

Solid solutions belonging to the Mn-rich region of the YCu_xMn_1–xO₃ system have been studied. The powders were prepared by solid-state reaction between the corresponding oxides. Sintered ceramics were obtained by firing at 1100–1325 °C. The incorporation of 30 at.% Cu to the yttrium manganite induces the formation of a perovskite-type phase, with orthorhombic symmetry. Increase of the Cu amount do not appreciably affects the orthorhombicity factor b/a, up to an amount of 50 at.% Cu. Above this Cu amount, a multiphase system has been observed, with the presence of unreacted-Y₂O₃, YMnO₃ and Y₂Cu₂O₅, along with a perovskite phase. DC electrical conductivity measurements have shown a semiconducting behaviour for all the solid solutions with perovskite-type structure. The room temperature conductivity increases with Cu until 33 at.% Cu, and then decreases. Thermally activated small polaron hopping mechanism, between Mn³⁺ and Mn⁴⁺ cations, controls the conductivity in these ceramics. Results are discussed as a function of the Mn³⁺/Mn⁴⁺ ratio for each composition.     

Methane combustion and CO oxidation on LaAl1−xMnxO3 perovskite-type oxide solid solutions

Structural, redox and catalytic deep oxidation properties of LaAl_1−xMn_xO₃ (x=0.0, 0.05, 0.1, 0.2, 0.4, 0.6, 0.8, 1.0) solid solutions prepared by the citrate method and calcined at 1073 K were investigated. XRD analysis showed that all the LaAl_1−xMn_xO₃ samples are single phase perovskite-type solid solutions. Particle sizes and surface areas (SA) are in the 280–1180 Å and 4–33 m² g⁻¹ ranges, respectively. Redox properties and the content of Mn⁴⁺ were derived from temperature programmed reduction (TPR) with H₂. Two reduction steps are observed by TPR for pure LaMnO₃, the first attributed to the reduction of Mn⁴⁺ to Mn³⁺ and the second due to complete reduction of Mn³⁺ to Mn²⁺. The presence of Al in the LaAl_1−xMn_xO₃ solid solutions produces a strong promoting effect on the Mn⁴⁺→Mn³⁺ reducibility and inhibits the further reduction to Mn²⁺. Both for methane combustion and CO oxidation all Mn-containing perovskites are much more active than LaAlO₃, so pointing to the essential role of the transition metal ion in developing highly active catalysts. Partial dilution with Al appears to enhance the specific activity of Mn sites for methane combustion.