Thermal and mechanical properties of linear low‐density polyethylene/low‐density polyethylene/wax ternary blends

The thermal and mechanical properties of uncrosslinked three‐component blends of linear low‐density polyethylene (LLDPE), low‐density polyethylene (LDPE), and a hard, paraffinic Fischer–Tropsch wax were investigated. A decrease in the total crystallinity with an increase in both LDPE and wax contents was observed. It was also observed that experimental enthalpy values of LLDPE in the blends were generally higher than the theoretically expected values, whereas in the case of LDPE the theoretically expected values were higher than the experimental values. In the presence of higher wax content there was a good correlation between experimental and theoretically expected enthalpy values. The DSC results showed changes in peak temperature of melting, as well as peak width, with changing blend composition. Most of these changes are explained in terms of the preferred cocrystallization of wax with LLDPE. Young's modulus, yield stress, and stress at break decreased with increasing LDPE content, whereas elongation at yield increased. This is in line with the decreasing crystallinity and increasing amorphous content expected with increasing LDPE content. Deviations from this behavior for samples containing 10% wax and relatively low LDPE contents are explained in terms of lower tie chain fractions. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1748–1755, 2005     

Phase morphology,thermomechanical, and crystallization behavior of uncompatibilized and PP‐g‐MAH compatibilized polypropylene/polystyrene blends

In this article, we discuss the phase morphology, thermal, mechanical, and crystallization properties of uncompatibilized and compatibilized polypropylene/polystyrene (PP/PS) blends. It is observed that the Young's modulus increases, but other mechanical properties such as tensile strength, flexural strength, elongation at break, and impact strength decrease by blending PS to PP. The tensile strength and Young's modulus of PP/PS blends were compared with various theoretical models. The thermal stability, melting, and crystallization temperatures and percentage crystallinity of semicrystalline PP in the blends were marginally decreased by the addition of amorphous PS. The presence of maleic anhydride‐grafted polypropylene (compatibilizer) increases the phase stability of 90/10 and 80/20 blends by preventing the coalescence. Hence, finer and more uniform droplets of PS dispersed phases are observed. The compatibilizer induced some improvement in impact strength for the blends with PP matrix phase, however fluctuations in modulus, strength and ductility were observed with respect to the uncompatibilized blend. The thermal stability was not much affected by the addition of the compatibilizer for the PP rich blends but shows some decrease in the thermal stability of the blends, where PS forms the matrix. On the other hand, the % crystallinity was increased by the addition of compatibilizer, irrespective of the blend concentration. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42100.     

Preparation and characterization of linear low‐density polyethylene/low‐density polyethylene/TiO2 membranes

Because of their special functions, the application of nanoscale powders has recently attracted both industrial and theoretical interest. In this study, nanoscale TiO₂, which exhibited a special UV absorption and consequent antibacterial function, was added to a low‐density polyethylene/linear low‐density polyethylene hybrid by melt compounding to yield functional composite membranes. TiO₂ exhibited an apparent induced nucleation effect on the crystallization of polyethylene, and the size of the crystallites decreased while the number increaed with the introduction of TiO₂; however, the crystallinity of polyethylene changed little. Also, TiO₂ exhibited an ideal dispersion in the membrane with an average size less than 100 nm, and this excellent dispersion provided the membranes extra UV absorption; moreover, the transparency of the membranes was maintained to satisfy common requirements. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 216–221, 2005     

Natural weather,soil burial and sea water ageing of low‐density polyethylene: Effect of starch/linear low‐density polyethylene masterbatch

Degradation of the blends of low‐density polyethylene (LDPE) with a starch‐based additive namely, polystarch N was studied under various environmental conditions such as natural weather, soil and sea water in Saudi Arabia. Stress–strain properties and thermal behavior were investigated for the LDPE and LDPE/polystarch N blend having 40% (w/w) of polystarch N. Environmental ageing resulted in the reduction of percentage of elongation and crystallinity for the blend. Rheological studies and scanning electron microscope photomicrographs of the polymer samples retrieved after ageing showed that addition of polystarch N enhanced the degradation of LDPE. This is ascribed to high extent of chain scission and leaching out of starch present in polystarch N, which was corroborated by the results of morphology and Fourier transform infrared spectroscopy analyses. In the case of underground soil ageing, microbes present in the soil consume the starch in the blend, thus accelerating the degradation process. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Low‐density polyethylene/plasticized tapioca starch blends with the low‐density polyethylene functionalized with maleate ester: Mechanical and thermal properties

In this study, the mechanical and thermal properties of low‐density polyethylene (LDPE)/thermoplastic tapioca starch blends were determined with LDPE‐g‐dibutyl maleate as the compatibilizer. Mechanical testing for the evaluation of the impact strength and tensile properties was carried our as per standard ASTM methods. Thermogravimetric analysis and differential scanning calorimetry were also used to assess the thermal degradation of the blends. Scanning electron micrographs were used to analyze fracture and blend morphologies. The results show significant improvement in the mechanical properties due to the addition of the compatibilizer, which effectively linked the two immiscible blend components. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1109–1120, 2006     

Recycled milk pouch and virgin low‐density polyethylene/linear low‐density polyethylene based coir fiber composites

The viability of the thermomechanical recycling of postconsumer milk pouches [a 50 : 50 low‐density polyethylene/linear low‐density polyethylene (LDPE–LLDPE) blend] and their use as polymeric matrices for coir‐fiber‐reinforced composites were investigated. The mechanical, thermal, morphological, and water absorption properties of recycled milk pouch polymer/coir fiber composites with different treated and untreated fiber contents were evaluated and compared with those of virgin LDPE–LLDPE/coir fiber composites. The water absorption of the composites measured at three different temperatures (25, 45, and 75°C) was found to follow Fickian diffusion. The mechanical properties of the composites significantly deteriorated after water absorption. The recycled polymer/coir fiber composites showed inferior mechanical performances and thermooxidative stability (oxidation induction time and oxidation temperature) in comparison with those observed for virgin polymer/fiber composites. However, a small quantity of a coupling agent (2 wt %) significantly improved all the mechanical, thermal, and moisture‐resistance properties of both types of composites. The overall mechanical performances of the composites containing recycled and virgin polymer matrices were correlated by the phase morphology, as observed with scanning electron microscopy. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Synthesis and characterization of linear low‐density polyethylene/sepiolite nanocomposites

Linear low‐density polyethylene (LLDPE)/sepiolite nanocomposites were prepared by melt blending using unmodified and silane‐modified sepiolite. Two methods were used to modify sepiolite: modification before heat mixing (ex situ) and modification during heat mixing (in situ). The X‐ray diffraction results showed that the position of the main peak of sepiolite remained unchanged during modification step. Infrared spectra showed new peaks confirming the development of new bonds in modified sepiolite and nanocomposites. SEM micrographs revealed the presence of sepiolite fibers embedded in polymer matrix. Thermogravimetric analysis showed that nanocomposites exhibited higher onset degradation temperature than LLDPE. In addition, in situ modified sepiolite nanocomposites exhibited higher thermal stability than ex situ modified sepiolite nanocomposites. The ultimate tensile strength and modulus of the nanocomposites were improved; whereas elongation at break was reduced. The higher crystallization temperature of some nanocomposite formulations revealed a heterogeneous nucleation effect of sepiolite. This can be exploited for the shortening of cycle time during processing. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Study of heat shrinkability of crosslinked low‐density polyethylene/poly(ethylene vinyl acetate) blends

In this study, the heat‐shrinkage property in polymer was induced by first compounding low‐density polyethylene/poly(ethylene vinyl acetate) (LDPE/EVA) blends with various amounts of peroxide in a twin‐screw extruder at about 130°C. The resulting granules were molded to shape and chemically crosslinked by compression molding. A process of heating–stretching–cooling was then performed on the samples while on a tensile machine. Shrinkability and effective parameters were also investigated using thermal mechanical analysis. The results showed that the gel fraction was higher for the sample of higher EVA content with the same amount of dicumyl peroxide (DCP). A decrease in the melting point and heat of fusion (ΔH_f), as determined from DSC, was observed with an increase in the DCP content. Studies on the heat shrinkability of the samples showed that samples stretched above the melting point had a higher shrinkage temperature than those stretched around the crystal transition temperature. The results showed that by increasing the peroxide content, the shrinkage temperature was decreased. These could be attributed to the formation of new spherulites as well as changes in the amount and the size of crystals. Furthermore, in samples elongated at 120°C (above the melting point), the rate of stretching had no effect on the shrinkage temperature. The results showed that the extent of strain had no effect on the temperature of shrinkage, but rather on the ultimate shrinkage value. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1389–1395, 2004     

Thermal and mechanical characterization of linear low‐density polyethylene/wood flour composites

A linear low‐density polyethylene (LLDPE) matrix was modified with an organic peroxide and by a reaction with maleic anhydride (MAn) and was simultaneously compounded with untreated wood flour in a twin‐screw extruder. The thermal and mechanical properties of the modified LLDPE and the resulting composites were evaluated. The degree of crystallinity was reduced in the modified LLDPE, but it increased with the addition of wood flour for the formation of the composites. Significant improvements in the tensile strength, ductility, and creep resistance were obtained for the MAn‐modified composites. This enhancement in the mechanical behavior could be attributed to an improvement in the compatibility between the filler and the matrix. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2775–2784, 2003     

Thermal properties and crystallization behavior of bamboo fiber/high‐density polyethylene composites: Nano‐TiO2 effects

In this study, bamboo fiber/high‐density polyethylene (HDPE) composites were prepared, and the effects of nano‐TiO₂ on their thermal properties and crystallization behavior were investigated via thermal gravimetric analysis (TGA), differential scanning calorimetry (DSC), X‐ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). The results show that the addition of nano‐TiO₂ improved the thermal stability and had a dual function in the crystallization behavior of the composites. On one hand, it functioned as a nucleating agent. The addition of 2 wt % nano‐TiO₂ promoted the crystallization, which caused the increase of the crystallization rate and crystallinity degree, as well as the micronization of the crystalline grain. On the other hand, intermolecular hydrogen bonds and covalent bonds were formed between nano‐TiO₂ and the polymer matrix, which hindered the crystallization of the composites. When the content of nano‐TiO₂ was continually increased, the inhibitory effect of the crystallization was gradually enhanced, which resulted in a decrease in the crystallization rate and crystallinity degree of the composites. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39846.     

Phase‐dependent binary interaction parameters in industrial low‐density polyethylene separators

In the production process of low‐density polyethylene (LDPE), an important step is the flash separation of monomers and other small molecules from the polymer produced. The process is carried out adiabatically in two stages. To improve the performance of thermodynamic models, it is very important to analyze the use of model binary interaction parameters (BIP) dependent on the phase characteristics for each phase (phase‐dependent BIP). In this work the PC‐SAFT (perturbed‐chain statistical associating fluid theory) equation of state (EOS) is applied to the flash simulation of LDPE industrial separators using eight different resins. The main numerical aspects are examined with emphasis on the optimization strategy for the EOS BIP that explicitly characterizes each phase involved separately. The results demonstrate good predictive behavior. As a result of improved and more consistent modeling, a new strategy for optimized operation can be envisaged for the sequence of separators. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2106–2117, 2013     

Morphology and rheological properties of compatibilized low‐density polyethylene/linear low‐density polyethylene/thermoplastic starch blends

Morphology and rheological properties of low‐density polyethylene/linear low‐density polyethylene/thermoplastic starch (LDPE/LLDPE/TPS) blends are experimentally investigated and theoretically analyzed using rheological models. Blending of LDPE/LLDPE (70/30 wt/wt) with 5–20 wt % of TPS and 3 wt % of PE‐grafted maleic anhydride (PE‐g‐MA) as a compatibilizer is performed in a twin‐screw extruder. Scanning electron micrographs show a fairly good dispersion of TPS in PE matrices in the presence of PE‐g‐MA. However, as the TPS content increases, the starch particle size increases. X‐ray diffraction patterns exhibit that with increase in TPS content, the intensity of the crystallization peaks slightly decreases and consequently crystal sizes of the blends decrease. The rheological analyses indicate that TPS can increase the elasticity and viscosity of the blends. With increasing the amount of TPS, starch particles interactions intensify and as a result the blend interface become weaker which are confirmed by relaxation time spectra and the prediction results of emulsion Palierne and Gramespacher‐Meissner models. It is demonstrated that there is a better agreement between experimental rheological data and Coran model than the emulsion models. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44719.     

Crystallization and fracture behaviors of high‐density polyethylene/linear low‐density polyethylene blends: The influence of short‐chain branching

Two commercial polyethylene samples, linear high‐density polyethylene (HDPE) and branched linear low‐density polyethylene with almost the same molecular weight distribution but different contents of short‐chain branching (SCB) were melt blended based on the consideration of practical application. Dynamic rheology analysis indicated good compatibility of all the blends with different compositions. Common differential scanning calorimeter (DSC) tests and successive self‐nucleation and annealing (SSA) treatment showed several interesting phenomena. First, without consideration of the effect of molecular weight and molecular weight distribution impact, co‐crystallization occurred at all ratios even the two components had a considerable difference in SCB distribution. Second, in SSA curves the area of the first two melting peaks, i.e., the amount of the thick lamellas of the two components showed an obvious positive deviation with the increase of HDPE content owing to the crystal perfection improved by the co‐crystallization. Essential Work of Fracture tests proved the co‐crystallization effects had a positive effect on the improvement of the resistance to crack propagation. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Improving low‐density polyethylene/poly(ethylene terephthalate) blends with graft copolymers

Blends of low‐density polyethylene (LDPE) and poly(ethylene terephthalate) (PET) were prepared with different weight compositions with a plasticorder at 240°C at a rotor speed of 64 rpm for 10 min. The physicomechanical properties of the prepared blends were investigated with special reference to the effects of the blend ratio. Graft copolymers, that is, LDPE‐grafted acrylic acid and LDPE‐grafted acrylonitrile, were prepared with γ‐irradiation. The copolymers were melt‐mixed in various contents (i.e., 3, 5, 7, and 9 phr) with a LDPE/PET blend with a weight ratio of 75/25 and used as compatibilizers. The effect of the compatibilizer contents on the physicomechanical properties and equilibrium swelling of the binary blend was investigated. With an increase in the compatibilizer content up to 7 phr, the blend showed an improvement in the physicomechanical properties and reduced equilibrium swelling in comparison with the uncompatibilized one. The addition of a compatibilizer beyond 7 phr did not improve the blend properties any further. The efficiency of the compatibilizers (7 phr) was also evaluated by studies of the phase morphology (scanning electron microscopy) and thermal properties (differential scanning calorimetry and thermogravimetric analysis). © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation and characterization of low‐density polyethylene/banana starch films containing compatibilizer and photosensitizer

Composite films containing various percentages of banana starch and low‐density polyethylene (LDPE) were prepared. The effects of the compatibilizer, banana starch content, and photosensitizer content on the thermal and tensile properties of these films were investigated. The banana starch content was varied from 5 to 20 wt % of LDPE, whereas benzophenone was added as a photosensitizer in three different amounts (0.25, 0.5, and 1 wt %) based on LDPE. In these films PE‐graft‐maleic anhydride (PE‐g‐MA) was used as a compatibilizer at 10 wt % banana starch. It was found that the thermal stability of the composite films remained unchanged with respect to the amount of banana starch and benzophenone content. The addition of banana starch had no effect on the melting temperature and degree of crystallinity of the films. Similarly, PE‐g‐MA had no effect on the melting temperature but decreased the degree of crystallinity of the LDPE phase. Benzophenone caused an increase in the melting temperature but decreased the degree of crystallinity of LDPE in the films. Increasing the amount of banana starch decreased the tensile properties of the composite films. The addition of PE‐g‐MA as a compatibilizer increased the tensile properties compared with the uncompatibilized films. However, benzophenone had no effect on the tensile properties of the blend films. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2717–2724, 2006     

Synthesis and characterization of graft copolymer of polyacrylonitrile‐g‐polyethylene glycol‐maleic acid monoester macromonomer

A novel solid–solid phase‐change energy storage material was synthesized by the aqueous phase precipitation polymerization. The amphiphilic polyethylene glycol‐maleic acid monoester macromonomer (MAPEG) with a double bond and a terminal carboxyl was the side chain and the polyacrylonitrile (PAN) was a skeleton. The chemical structure and thermal properties of the graft copolymer were investigated. The results indicated that the MAPEG chains were successfully grafted onto the PAN backbone. The graft copolymer possess good thermal reliability and the phase‐transition temperature is in the temperature range of human comfort, meanwhile, the melting enthalpy could reach 74.16 J/g and the crystallization enthalpy could reach 65.40 J/g, accounting for theoretical enthalpy value of 89 and 93%, respectively. Besides, optimum conditions of synthesizing the graft copolymer were determined by orthogonal experiment. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40152.     

Thermal fractionation and crystallization enhancement of silane‐grafted water‐crosslinked low‐density polyethylene

Thermal fractionations performed using differential scanning calorimetry (DSC) to characterize the heterogeneities in molecular structures of low‐density polyethylene (LDPE), silane‐grafted LDPE (G‐LDPE), and silane‐grafted water‐crosslinked LDPE with gel fractions of 30 and 70 wt % are reported. In regular DSC analyses, LDPE, G‐LDPE, and the low gel fraction of crosslinked samples (30 wt %) give one broad endothermic peak at ～110 °C, whereas the high gel fraction of crosslinked samples (70 wt %) give overlapped multiple endothermic peaks in a much broader temperature range. After thermally fractionated in the range 60–145 °C, LDPE, G‐LDPE, and the low gel fraction samples give five to six endothermic peaks in the low‐temperature range, whereas the high gel fraction samples give nine peaks, with three additional peaks appearing in the high‐temperature range. These multiple peaks correspond to fractions of different molecular structures, with the additional peaks for the high gel fraction samples corresponding to the fraction of molecular segments with low or no branching. This fraction of molecular segments is increasingly extruded out of the gel region with increasing gel fraction by crosslinking and leads to an enhancement of crystallization of the sample. This crystallization enhancement behavior is also demonstrated by the X‐ray diffraction data and polarized optical micrographs. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 591–599, 2001     

Morphological and physicomechanical analysis of high‐density polyethylene filled with Salago fiber

The environmental issues associated with the mass discarding of waste plastics in the Philippines have significantly raised for the past decade. However, this country is a home to many natural fibers which necessitates the development of ecofriendly materials to diminish the environmental footprint of polymers. High‐density polyethylene (HDPE) was filled with floured untreated and 5 wt % alkaline‐treated Salago fiber via melt compounding. The physical and mechanical characteristics of both types of composites were measured and compared. The composite filled with 30 wt % untreated fiber became very brittle, showing tensile strength and impact resistance of 15.8 MPa and 4.9 kJ/m², respectively. Alkaline treatment improved the mechanical properties of untreated composites, but not above the value of virgin HDPE. Nevertheless, the flexural strength of treated composites exceeded that of the virgin HDPE. Untreated composites absorbed water twice as the treated ones. Finally, morphological and fractography inspection on tensile and flexural test specimens showed improvement made by treatment on the interfacial adhesion between fiber and thermoplastic, corroborating the results from mechanical properties test. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46479.     

Composite of low‐density polyethylene and aluminum obtained from the recycling of postconsumer aseptic packaging

The recycling process of postconsumer aseptic packaging composed of paper, low‐density polyethylene (LDPE), and aluminum consists of recovering paper, the major component, through centrifugation. The remaining mixture of LDPE and aluminum, a recycled composite called PEAL, offers an interesting combination of properties, especially because of the presence of a small amount of poly(ethylene‐co‐methacrylic acid (EMAA). In this work, this composite is characterized, and the properties are compared with those of pure LDPE and EMAA, the polymers that constitute the recycled material. PEAL is around 15% aluminum particles with different shapes and sizes. The composite presents higher thermooxidative stability, higher crystallinity, lower impact resistance, and higher tensile strength than the other olefin polymers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3183–3191, 2006     

Effects of polyethylene‐grafted maleic anhydride (PE‐g‐MA) on thermal properties,morphology, and tensile properties of low‐density polyethylene (LDPE) and corn starch blends

The effects of polyethylene‐grafted maleic anhydride (PE‐g‐MA) on the thermal properties, morphology, and tensile properties of blends of low‐density polyethylene (LDPE) and corn starch were studied with a differential scanning calorimeter (DSC), scanning electron microscope (SEM), and Instron Universal Testing Machine, respectively. Corn starch–LDPE blends with different starch content and with or without the addition of PE‐g‐MA were prepared with a lab‐scale twin‐screw extruder. The crystallization temperature of LDPE–corn starch–PE‐g‐MA blends was similar to that of pure LDPE but higher than that of LDPE–corn starch blends. The interfacial properties between corn starch and LDPE were improved after PE‐g‐MA addition, as evidenced by the structure morphology revealed by SEM. The tensile strength and elongation at break of corn starch–LDPE–PE‐g‐MA blends were greater than those of LDPE–corn starch blends, and their differences became more pronounced at higher starch contents. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2904–2911, 2003