A 100 MS/s 4 MHz Bandwidth 70 dB SNR $Delta Sigma$ ADC in 90 nm CMOS

This paper describes the results of an implementation of a high speed $Delta Sigma$ ADC in 90 nm CMOS process, which is developed for a direct-conversion digital TV receiver. The $Delta Sigma$ ADC is based on a switched-capacitor fourth-order single-loop $Delta Sigma$ modulator with a 4-bit quantizer. The ADC uses a triple sampling technique and a two-step summation scheme for low power and high speed operation. Also, a digital signal processing block, including a decimation filter, a channel selection filter and a digital programmable gain amplifier (PGA), is implemented in the same process. The decimation filter is based on a polyphase IIR filter with a decimation ratio of 5, while the channel selection filter is based on two path lattice wave digital IIR filter. The ADC achieves 69.95 dB SNR and 66.85 dB SNDR over a 4 MHz bandwidth with a sampling frequency of 100 MHz. The fabricated $Delta Sigma$ ADC and the digital signal processing block occupy 0.53$~$mm$^2$ and 0.09 mm$^{2}$, and consume 11.76 mW per channel.      

Post-CMOS Compatible Micromachining Technique for On-Chip Passive RF Filter Circuits

This paper reports on a post-CMOS compatible micromachining technology for passive RF circuit integration. The micromachining technology combines the formation of high-performance microelectromechanical systems solenoid inductors and metal—insulator—metal (MIM) capacitors by using a post-CMOS process on standard CMOS substrate. Utilizing this process, novel on-chip 3-D configured RF filters for 5 GHz band are integrated on-chip. Two types of compact filters are designed and fabricated, with the layout size of the bandpass filter as 0.65 $,times,$0.67 ${rm mm}^{ 2}$ and that of the low-pass filter as 0.77$,{ times },$1.25 ${rm mm}^{ 2}$. From the measurement results, the fifth-order low-pass filter shows less than 1.06 dB insertion loss up to 5 GHz and ${-}{rm 1.5}~{rm dB}$ cutoff frequency at 5.3 GHz. The bandpass filter is a second-order coupled-resonator type, with measured 4.3 dB minimum insertion loss and better than 13 dB return loss in the pass band. Both simulation and shock testing results have shown that the filters are almost free of influence from environmental vibration and shock. From the measured results in various temperatures, the bandpass filters were found to show lower loss under low temperatures, while the passband shift is negligible in the various temperatures. Together with the fabricated filters, the developed micromachining technique has demonstrated the potential of on-chip integration and miniaturization of passive RF circuits.      

180$^{circ}$ and 90$^{circ}$ Phase Shifting Networks With an Octave Bandwidth and Small Phase Errors

A new phase shifting network for both 180 $^{circ}$ and 90 $^{circ}$ phase shift with small phase errors over an octave bandwidth is presented. The theoretical bandwidth is 67% for the 180$^{circ}$ phase bit and 86% for the 90$^{circ}$ phase bit when phase errors are $pm 2^{circ}$. The proposed topology consists of a bandpass filter (BPF) branch, consisting of a LC resonator and two shunt quarter-wavelength transmission lines (TLs), and a reference TL. A theoretical analysis is provided and scalable parameters are listed for both phase bits. To test the theory, phase shifting networks from 1 GHz to 3 GHz were designed. The measured phase errors of the 180$^{circ}$ and the 90$^{circ}$ phase bit are $pm 3.5^{circ}$ and $pm 2.5^{circ}$ over a bandwidth of 73% and 102% while the return losses are better than 18 dB and 12 dB, respectively.      

Integrated Quadrature Couplers and Their Application in Image-Reject Receivers

Several fully-integrated multi-stage lumped-element quadrature hybrids that enhance bandwidth, amplitude and phase accuracies, and robustness are presented, and a fully-integrated double-quadrature heterodyne receiver front-end that uses two-stage Lange/Lange couplers is described. The Lange/Lange cascade exploits the inherent wide bandwidth characteristic of the Lange hybrid and enables a robust design using a relatively low transformer coupling coefficient. The measured image-rejection ratio is $>$ 55 dB over a 200 MHz bandwidth centered around 5.25 $~$GHz without any tuning, trimming, or calibration; the front-end features 23.5 dB gain, $-$79 dBm sensitivity, 5.6 dB SSB NF, $-$7$~$ dBm IIP3, $-$18 dB $S_{11}$ and a 1 mm $times$ 2 mm die area in 0.18$ mu{hbox {m}}$ CMOS.      

A 2.4–2.5 GHz WLAN Direct-Conversion Receiver Front-End With Low-Distortion Baseband Filters

Low-distortion I/Q baseband filters interface with a 2.5 GHz RF receiver front-end configured as a Gm-cell in a direct-conversion architecture targeted towards WLAN 802.11b application. The active I/Q current-mode filters use AC current to carry the large swing of both desired and blocker signals, relaxing the voltage headroom requirement to a 1.2 V supply. An on chip master–slave automatic tuner is used to lock the filter bandwidth to a precision 20 MHz reference crystal oscillator, resulting in a $≪ ,$3% tuning accuracy and $≪, $ 0.5% I/Q bandwidth matching. The receiver achieves a 3.2 dB DSB NF, ${-}$14 dBm out-of-band IIP3, and ${+}$ 27 dBm worst case IIP2, all referred to the LNA input, while drawing 30mA from a 2.7 V supply. The chip is fabricated in a 0.5 $mu$m 46 GHz $f_{T}$ SiGe BiCMOS process. The active area is 2.54 mm$^{2}$ .      

A 0.55 V 60 dB-DR Fourth-Order Analog Baseband Filter

A 0.55 V supply voltage fourth-order low-pass continuous-time filter is presented. The low-voltage operating point is achieved by an improved bias circuit that uses different opamp input and output common-mode voltages. The fourth-order filter architecture is composed by two Active- ${rm G}_{rm m}{-}{rm RC}$ biquadratic cells, which use a single opamp per-cell with a unity-gain-bandwidth comparable to the filter cut-off frequency. The $-$ 3 dB filter frequency is 12 MHz and this is higher than any other low-voltage continuous-time filter cut-off frequency. The $-$3 dB frequency can be adjusted by means of a digitally-controlled capacitance array. In a standard 0.13 $mu{rm m}$ CMOS technology with ${V}_{THN}approx 0.25 {rm V}$ and ${V}_{THP}approx 0.3 {rm V}$, the filter operates with a supply voltage as low as 0.55 V. The filter $({rm total} {rm area}=0.47 {rm mm}^{2})$ consumes 3.4 mW. A 8 dBm-in-band IIP3 and a 13.3 dBm-out-of-band IIP3 demonstrate the validity of the proposal.      

An FIR-Embedded Noise Filtering Method for $Delta Sigma$ Fractional-N PLL Clock Generators

This paper describes a noise filtering method for $Delta Sigma$ fractional- $N$ PLL clock generators to reduce out-of-band phase noise and improve short-term jitter performance. Use of a low-cost ring VCO mandates a wideband PLL design and complicates filtering out high-frequency quantization noise from the $Delta Sigma$ modulator. A hybrid finite impulse response (FIR) filtering technique based on a semidigital approach enables low-OSR $Delta Sigma$ modulation with robust quantization noise reduction despite circuit mismatch and nonlinearity. A prototype 1-GHz $Delta Sigma$ fractional-$N$ PLL is implemented in 0.18 $muhbox{m}$ CMOS. Experimental results show that the proposed semidigital method effectively suppresses the out-of-band quantization noise, resulting in nearly 30% reduction in short-term jitter.      

17 GHz RF Front-Ends for Low-Power Wireless Sensor Networks

A 17 GHz low-power radio transceiver front-end implemented in a 0.25 $mu{hbox {m}}$ SiGe:C BiCMOS technology is described. Operating at data rates up to 10 Mbit/s with a reduced transceiver turn-on time of 2 $mu{hbox {s}}$, gives an overall energy consumption of 1.75 nJ/bit for the receiver and 1.6 nJ/bit for the transmitter. The measured conversion gain of the receiver chain is 25–30 dB into a 50 $Omega$ load at 10 MHz IF, and noise figure is 12 $pm$0.5 dB across the band from 10 to 200 MHz. The 1-dB compression point at the receiver input is $-$37 dBm and ${hbox{IIP}}_{3}$ is $-$25 dBm. The maximum saturated output power from the on-chip transmit amplifier is $-$1.4 dBm. Power consumption is 17.5 mW in receiver mode, and 16 mW in transmit mode, both operating from a 2.5 V supply. In standby, the transceiver supply current is less than 1 $mu{hbox {A}}$.      

Analysis and Design of a CMOS UWB LNA With Dual- -Branch Wideband Input Matching Network

A wideband low-noise amplifier (LNA) based on the current-reused cascade configuration is proposed. The wideband input-impedance matching was achieved by taking advantage of the resistive shunt–shunt feedback in conjunction with a parallel LC load to make the input network equivalent to two parallel $RLC$-branches, i.e., a second-order wideband bandpass filter. Besides, both the inductive series- and shunt-peaking techniques are used for bandwidth extension. Theoretical analysis shows that both the frequency response of input matching and noise figure (NF) can be described by second-order functions with quality factors as parameters. The CMOS ultra-wideband LNA dissipates 10.34-mW power and achieves ${ S}_{11}$ below $-$8.6 dB, ${ S}_{22}$ below $-$10 dB, ${ S}_{12}$ below $-$26 dB, flat ${ S}_{21}$ of 12.26 $pm$ 0.63 dB, and flat NF of 4.24 $ pm$ 0.5 dB over the 3.1–10.6-GHz band of interest. Besides, good phase linearity property (group-delay variation is only $pm$22 ps across the whole band) is also achieved. The analytical, simulated, and measured results agree well with one another.      

A 0.13 $mu$ m CMOS Quad-Band GSM/GPRS/EDGE RF Transceiver Using a Low-Noise Fractional-N Frequency Synthesizer and Direct-Conversion Architecture

This paper presents a single-chip CMOS quad-band (850/900/1800/1900 MHz) RF transceiver for GSM/GPRS/EDGE applications which adopts a direct-conversion receiver, a direct-conversion transmitter and a fractional-N frequency synthesizer with a built-in DCXO. In the GSM mode, the transmitter delivers 4 dBm of output power with 1$^{circ}$ RMS phase error and the measured phase noise is ${-}$164.5 dBc/Hz at 20 MHz offset from a 914.8$~$MHz carrier. In the EDGE mode, the TX RMS EVM is 2.4% with a 0.5 $~$dB gain step for the overall 36 dB dynamic range. The RX NF and IIP3 are 2.7 dB/ ${-}$12 dBm for the low bands (850/900 MHz) and 3 dB/${-}$ 11 dBm for the high bands (1800/1900 MHz). This transceiver is implemented in 0.13 $mu$m CMOS technology and occupies 10.5 mm$^{2}$ . The device consumes 118 mA and 84 mA in TX and RX modes from 2.8 V, respectively and is housed in a 5$,times,$ 5 mm$^{2}$ 40-pin QFN package.      

A Highly Linear SAW-Less CMOS Receiver Using a Mixer With Embedded Tx Filtering for CDMA

An embedded filtering passive (EFP) mixer is used to overcome transmitter power leakage in a receiver without the use of a SAW filter. The receiver IC exhibits more than ${+}$ 60 dBm of Rx IIP$_{2}$ , 2.4 dB Rx noise figure, and ${+}$77 dB of Triple Beat (TB) with 45 MHz offset transmit leakage at 900 MHz Rx frequency while consuming only 18 mA from a 2.1 V supply. Thanks to the embedded filtering passive mixer, the proposed receiver IC shows an additional 15 dB Tx rejection compared to a conventional receiver. The additional Tx rejection improved the IIP $_{2}$ by 10 dB and TB by 30 dB. The complete receiver consists of a differential LNA employing an active post-distortion (APD), I/Q embedded filtering passive mixer, two TIAs for I/Q outputs. The fabricated receiver IC occupies 2.25 mm$^{2}$ including bonding pads, ESD devices, local oscillator (LO) input buffer, frequency divider, and mixer drivers. The receiver is fabricated using a 0.18 $mu$m CMOS process with 5 metal and 1 poly (5M1P) layer.      

Temperature-Insensitive Dual-Comb Filter Based on Multimode Interference Ti : LiNbO $_{3}$ Waveguide

A temperature-insensitive dual-comb filter has been demonstrated for the first time by multimode interference based on a Ti : LiNbO$_{3}$ channel waveguide. The phase difference between comb filters was about 180 $^{circ}$. We only observed less than ${pm}$0.125-nm variation of the center wavelength of the filter during temperature change from 20 $^{circ}$C to 50 $^{circ}$C. The measured extinction ratio and channel spacing of the comb filter were about ${-}$25 dB and 3.2 THz, respectively.      

A 9 mW Highly-Digitized 802.15.4 Receiver Using Bandpass $SigmaDelta$ ADC and IF Level Detection

A low power (9 mW) highly-digitized 2.4 GHz receiver for sensor network applications (IEEE 802.15.4 LR-WPAN) is realized by a 0.18 $mu{rm m}$ CMOS process. We adopted a novel receiver architecture adding an intermediate frequency (IF) level detection scheme to a low-power complex fifth-order continuous-time (CT) bandpass $SigmaDelta$ modulator in order to digitalize the receiver. By the continuous-time bandpass architecture, the proposed $SigmaDelta$ modulator requires no additional anti-aliasing filter in front of the modulator. Using the IF detector, the achieved dynamic range (DR) of the overall system is 95 dB at a sampling rate of 64 MHz. This modulator has a bandwidth of 2 MHz centered at 2 MHz. The power consumption of this receiver is 9.0 mW with a 1.8 V power supply.      

A 10:1 Unequal Wilkinson Power Divider Using Coupled Lines With Two Shorts

A novel unequal Wilkinson power divider is presented. A coupled-line section with two shorts is proposed to realize the high characteristic impedance line, which cannot be implemented by conventional microstrip fabrication technique due to fabrication limitation. The proposed coupled-line structure is compatible with single layer integration and can be easily designed based on an even-odd mode analysis. As a design example, a 10:1 Wilkinson power divider at 2 GHz is fabricated and measured. The measured $-10~{rm dB}$ bandwidth of $S_{11}$ is about 16%, and the isolation $S_{32}$ is better than $-20~{rm dB}$ . The measured amplitude balance between output port 2 and port 3 is between $-10.20~{rm dB}$ and $-9.52~{rm dB}$, and the corresponding phase difference is between 0$^{circ}$ and 4.6$^{circ}$.      

Q-Band pHEMT and mHEMT Subharmonic Gilbert Upconversion Mixers

This letter makes a comparison between Q-band 0.15 $mu{rm m}$ pseudomorphic high electron mobility transistor (pHEMT) and metamorphic high electron mobility transistor (mHEMT) stacked-LO subharmonic upconversion mixers in terms of gain, isolation and linearity. In general, a 0.15 $mu{rm m}$ mHEMT device has a higher transconductance and cutoff frequency than a 0.15 $mu{rm m}$ pHEMT does. Thus, the conversion gain of the mHEMT is higher than that of the pHEMT in the active Gilbert mixer design. The Q-band stacked-LO subharmonic upconversion mixers using the pHEMT and mHEMT technologies have conversion gain of $-$7.1 dB and $-$0.2 dB, respectively. The pHEMT upconversion mixer has an ${rm OIP}_{3}$ of $-$12 dBm and an ${rm OP}_{1 {rm dB}}$ of $-$24 dBm, while the mHEMT one shows a 4 dB improvement on linearity for the difference between the ${rm OIP}_{3}$ and ${rm OP}_{1 {rm dB}}$. Both the chip sizes are the same at 1.3 mm $times$ 0.9 mm.      

Improved Microwave Noise Performance by SiN Passivation in AlGaN/GaN HEMTs on Si

Effects of silicon nitride (SiN) surface passivation by plasma enhanced chemical vapor deposition (PECVD) on microwave noise characteristics of AlGaN/GaN HEMTs on high-resistivity silicon (HR-Si) substrate have been investigated. About 25% improvement in the minimum noise figure $(NF_{min})$ (0.52 dB, from 2.03 dB to 1.51 dB) and 10% in the associate gain $(G_{rm a})$ (1.0 dB, from 10.3 dB to 11.3 dB) were observed after passivation. The equivalent circuit parameters and noise source parameters (including channel noise coefficient $(P)$, gate noise coefficient $(R)$, and their correlation coefficient $(C)$ ) were extracted. $P$ , $R$ and $C$ all increased after passivation and the increase of C contributes to the decrease of the noise figure. It was found that the improved microwave small signal and noise performance is mainly due to the increase of the intrinsic transconductance $(g_{{rm m}0})$ and the decrease of the extrinsic source resistance $(R_{rm s})$.      

A 108 dB SNR, 1.1 mW Oversampling Audio DAC With A Three-level DEM Technique

A low power audio oversampling $Sigma Delta $ digital-to-analog converter (DAC) with a three-level $(+1,~0,-1)$ dynamic-element-matching (DEM) technique and an inter-symbol interference-free (ISI) output stage is presented. Solutions for design challenges such as ISI, clock jitter sensitivity, and out-of-band noise are presented. The converter is fabricated in a 0.18 $mu{hbox {m}}$ CMOS process, occupies 0.55 ${hbox {mm}}^{2}$, achieves 108 dB dynamic range, $-98~{rm dB ~THD}+{rm N}$ while consumes a total of 1.1 mW per channel at 1.8 V supply.      

2 MHz AO $Q$ -switched ${rm TEM}_{00}$ Grazing Incidence Laser With 3 at.% Neodymium Doped Nd:YVO$_{4}$

We present a detailed experimental and theoretical study of the ultrahigh repetition rate AO $Q$ -switched ${rm TEM}_{00}$ grazing incidence laser. Up to 2.1 MHz $Q$-switching with ${rm TEM}_{00}$ output of 8.6 W and 2.2 MHz $Q$ -switching with multimode output of 10 W were achieved by using an acousto-optics $Q$ -switched grazing-incidence laser with optimum grazing-incidence angle and cavity configuration. The crystal was 3 at.% neodymium doped Nd:YVO$_{4}$ slab. The pulse duration at 2 MHz repetition rate was about 31 ns. The instabilities of pulse energy at 2 MHz repetition rate were less than ${pm}6.7hbox{%}$ with ${rm TEM}_{00}$ operation and ${pm}3.3hbox{%}$ with multimode operation respectively. The modeling of high repetition rate $Q$-switched operation is presented based on the rate equation, and with the solution of the modeling, higher pump power, smaller section area of laser mode, and larger stimulated emission cross section of the gain medium are beneficial to the $Q$-switched operation with ultrahigh repetition rate, which is in consistent with the experimental results.      

10-GHz and 20-GHz Channel Spacing High-Resolution AWGs on InP

This letter reports on 10-GHz and 20-GHz channel-spacing arrayed waveguide gratings (AWGs) based on InP technology. The dimensions of the AWGs are 6.8$,times,$8.2 mm$^{2}$ and 5.0$,times,$6.0 mm$^{2}$, respectively, and the devices show crosstalk levels of $-$12 dB for the 10-GHz and $-$17 dB for the 20-GHz AWG without any compensation for the phase errors in the arrayed waveguides. The root-mean-square phase errors for the center arrayed waveguides were characterized by using an optical vector network analyzer, and are 18 $^{circ}$ for the 10-GHz AWG and 28$^{circ}$ for the 10-GHz AWG.      

Tunable Linear MOS Resistors Using Quasi-Floating-Gate Techniques

A family of tunable MOS resistors based on quasi-floating-gate (QFG) transistors biased in the triode region is analyzed in this paper. From the study results, a new device that outperforms previous implementations, is presented. By means of a capacitive divider, the ac component of the drain-to-source voltage scaled with a factor $alphaleq 1$ is added to the gate-to-source voltage leading to a cancellation of the nonlinear terms. The effect of $alpha$ on resistor linearity is analytically studied. Simulation results are also provided for different technologies. Finally, a complete transconductor has been built which preserves the linearity of the MOS resistor. Three versions of the transconductor have been fabricated for different values of $alpha$ ($alpha=$ 0, 0.5, and 1) in a 0.5 $mu{hbox {m}}$ CMOS technology with $pm$1.65-V supply voltage. Experimental results show (for $alpha=1$ ) a THD of $-$ 57 dB $({rm HD}2=-70 {hbox {dB}})$ at 1 MHz for 2-V peak-to-peak differential input signal with a nominal ac-transconductance of 200 $muhbox{A/V}$ and a power consumption of 3.2 mW.