Synthesis and characterization of hyperbranched aromatic poly(ester-imide)s

The synthesis and characterization of hyperbranched aromatic poly(ester-imide)s are described. A variety of AB₂ monomers, N-[3- or 4-bis(4-acetoxyphenyl)toluoyl]-4-carboxyl-phthalimide and N-{3- or 4-[1,1-bis(4-acetooxyphenyl)]ethylphenyl}-4-carboxy phthalimides were prepared starting from condensation of nitrobenzaldehydes or nitroacetophenones with phenol and used for synthesis of hyperbranched poly(ester-imide)s containing terminal acetyl groups by transesterification reaction. These hyperbranched poly(ester-imide)s were produced with weight-average molecular weight of up to 6.87 g/mol. Analysis of ¹H NMR and ¹³C NMR spectroscopy revealed the structure of the four hyperbranched poly(ester-imide)s. These hyperbranched poly(ester-imide)s exhibited excellent solubility in a variety of solvents such as N,N-dimethylacetamide, dimethyl sulfoxide, and tetrahydrofuran and showed glass-transition temperatures between 217 and 255 °C. The thermogravimetric analytic measurement revealed the decomposition temperature at 10% weight-loss temperature (T_d¹⁰) ranging from 365 to 416 °C in nitrogen.     

Miscibility,crystallization and annealing studies of poly(vinylidene fluoride)/hyperbranched polyester blends

In this study, miscibility and crystallization behavior of polyvinylidene fluoride (PVDF) and its blends with hyperbranched polyester (HBPE, 0 to 50 wt.-% of HBPE in PVDF) are investigated by means of DSC and FTIR techniques. Among the varying blend compositions, PVDF/HBPE (100/0 and 90/10) blend ultrathin film samples were subjected to thermal annealing at different temperatures (30–200 °C) in order to examine and compare their crystallization behavior. From FTIR data, the all-trans band (A₁) at ca. 1280 cm⁻¹ corresponding to the changes in ferroelectric β-crystalline phase for both the samples exhibits higher absorption intensity upon annealing at 90 °C, well below their melting temperature range (T_m∼160 °C), whereas, the sample melt-annealed at 210 °C exhibit reduced A₁ absorption intensity, which is attributed to the crystalline transformation from ordered ferroelectric phase into the disordered amorphous phase. Quantitative data from Factor analysis revealed the existence of higher ferroelectric β-crystalline phase content in PVDF/HBPE (90/10) blend ultrathin film sample than in commercially available PVDF and PVDF/TrFE (72/28) ultrathin film samples, which exemplifies the importance of this study. The enhanced ferroelectric characteristics exhibited by the PVDF/HBPE (90/10) blend ultrathin film samples can be well-suited for electronic applications such as non-volatile memory devices, sensors, etc.     

Electrospinning of linear and highly branched segmented poly(urethane urea)s

Electrospun fibrous mats were formed from linear and highly branched poly(urethane urea)s. The highly branched poly(urethane urea)s were synthesized using an A₂+B₃ methodology, where the A₂ species is an oligomeric soft segment. Since the molecular weight of the A₂ oligomer is above the entanglement molecular weight, the highly branched polymers formed electrospun fibers unlike typical hyperbranched polymers that do not entangle. Stress-strain experiments revealed superior elongation for the electrospun fibrous mats. In particular, the highly branched fiber mats did not fail at 1300% elongation, making the electrospun mats promising for potential applications where enhanced tear strength resistance is required.     

Synthesis and properties of novel poly(tetramethylsilnaphthylenesiloxane) derivatives

Novel poly(tetramethylsilnaphthylenesiloxane) derivatives were synthesized and characterized by differential scanning calorimetry (DSC), thermogravimetry (TG), and X-ray diffraction analyses. Poly(tetramethylsilnaphthylenesiloxane) derivatives were obtained by condensation polymerization of the corresponding disilanol derivatives, i.e. 1,4-, 1,5-, 2,6-, and 2,7-bis(dimethylhydroxysilyl)naphthalenes, which were prepared by the Grignard reaction using chlorodimethylsilane and the corresponding dibromonaphthalene derivatives followed by the hydrolyses, catalyzed by palladium on charcoal. The obtained poly(tetramethyl-1,5-silnaphthylenesiloxane) was insoluble in common organic solvents; however, the other polymers exhibited the good solubility in common organic solvents, such as tetrahydrofuran (THF), chloroform, dichloromethane, and toluene. The introduction of tetramethyl-1,5-silnaphthylenesiloxane units into the resulting polymer was confirmed by ¹H NMR spectrum of the copolymer obtained by condensation copolymerization of 1,5-bis(dimethylhydroxysilyl)naphthalene with 1,4-bis(dimethylhydroxysilyl)naphthalene. It was revealed from the DSC and X-ray diffraction measurements that poly(tetramethyl-1,5-silnaphthylenesiloxane) and poly(tetramethyl-2,6-silnaphthylenesiloxane) exhibited the crystallinity; however, poly(tetramethyl-1,4-silnaphthylenesiloxane) and poly(tetramethyl-2,7-silnaphthylenesiloxane) were amorphous. The glass transition temperature (T_g) and the temperature at 5% weight loss (T_d5) of poly(tetramethylsilnaphthylenesiloxane) derivatives with dimethylsilyl group at 1-position of the naphthylene moiety were higher than those at 2-position of the naphthylene moiety. The T_g and melting point (T_m) of the present polymers were higher than those of poly(tetramethyl-1,4-silphenylenesiloxane).     

Surface and mechanical properties of microporous membranes of poly(ethylene glycol)-polydimethylsiloxane copolymer/chitosan

Poly(ethylene glycol)-polydimethylsiloxane (PEG-PDMS) block copolymers were prepared via a condensation reaction between PEG diacid and PDMS diol. PEG diacid was synthesized from the reaction between hydroxy-terminated PEG and succinic anhydride. PDMS diol was prepared from the ring-opening polymerization of octamethylcyclotetrasiloxane (D₄) followed by hydrosilylation with allyl alcohol. The copolymers were incorporated into chitosan in order that good water swellability and wettability of chitosan were retained due to hydrophilic PEG blocks, whereas PDMS block in the copolymers functioned as a toughening modifier. Percent crosslinking of 66-84 was observed once 5-10 wt% of the copolymers was incorporated. As compared to the unmodified sample, the copolymer-containing chitosan exhibited the decreases in both water contact angles and the rate of water vapor permeability. The studies on tensile properties indicated that incorporation of copolymers into chitosan improved the flexibility of the films.     

改性超支化聚（胺-酯）对亚硝酸根的吸附性能研究

以十八烷基三氯硅烷对超支化聚（胺-酯）进行改性,合成了改性的超支化聚（胺-酯）。改性的超支化聚（胺-酯）是一种既具有大量的端羟基且易从中水中分离出来的超支化聚（胺-酯）。将改性的超支化聚（胺-酯）用于吸附亚硝酸根离子,实验结果表明：改性的超支化聚合物对亚硝酸根离子的最大吸附量可达149．7mg／g,在酸性溶液中吸附量还将大大增加。     

Synthesis, optical and electrochemical properties of new hyperbranched poly(triphenylamine amide)s

A new triphenylamine-containing AB₂ type monomer with one carboxylic acid and two amino groups, 4-(bis(4-aminophenyl)amino)benzoic acid (3), was synthesized and used for the preparation of hyperbranched poly(triphenylamine amide)s. The self-polycondensation of the AB₂ monomer (3) afforded hyperbranched poly(triphenylamine amide) with amino end groups. The molecular weight of the hyperbranched poly(triphenylamine amide) was 21,000 Da determined by light scattering. End-capped hyperbranched polyamides were isolated by the chemical modification of unreacted amino groups with various acid chlorides. All the hyperbranched poly(triphenylamine amide)s exhibit excellent solubility in organic solvents such as NMP, DMF, DMSO, and DMAc at room temperature. The viscosities of hyperbranched poly(triphenylamine amide)s are as low as about 0.15 dL/g due to their dendritic structures. Poly(triphenylamine amide)s end-capped with rigid benzene ring have higher thermal stability than those with amino or aliphatic end groups. The photoluminescence of the hyperbranched polyamides is blue-yellow emissions around 430-510 nm. The energy gaps of the hyperbranched poly(triphenylamine amide)s with different end groups are about 2.93 eV and are independent on the end groups, but the HOMO and LUMO energy levels are dependent on the end groups.     

Physical and thermal properties of UV curable waterborne polyurethane dispersions incorporating hyperbranched aliphatic polyester of varying generation number

Three series of novel waterborne hyperbranched polyurethane acrylates for UV curable aqueous dispersions (WHPUD) based on hydroxy-functionalized hyperbranched aliphatic polyesters Boltorn™ of varying generation number were investigated. The effects of the overall composition, including acidic and acrylate groups, and functionality of hyperbranched polyester were studied in terms of particle size, rheology, photopolymerization kinetics, dynamic mechanical thermal as well as thermal degradation behaviors of WHPUDs. The average particle sizes of aqueous dispersions, 43-134 nm, were determined by laser light scattering. The stability and particle size were dependent on the amount of carboxylic acid groups, degree of neutralization, and molecular structure. The rheological features have revealed that all dispersions belong to pseudoplastic fluids. The shear thinning behavior of WHPUDs is more pronounced for lower generation of hyperbranched polyester. The photopolymerization rates of the resins under UV irradiation in the presence of a photoinitiator showed an increasing trend with higher functionality of acrylate. The glass transition temperature (T_g) of UV cured films evaluated by dynamic mechanical thermal analysis (DMTA) showed that the influence of end capping by hard segment consisting of IPDI-HEA is remarkable due to the increase of crosslink density. The T_g, storage modulus and loss modulus increased with increasing generation number from the second to the fourth. The results of TGA for cured WHPUD films indicated good thermal stability with no appreciable weight loss until 200 °C, and that an increase in the hard segment content provoked the increases in thermal degradation temperature. This behavior is rationalized by relating crosslink density dependence of chain end concentration and the generation number of hyperbranched polyester.     

Synthesis, characterization, and crosslinking of soluble cyano-containing poly(arylene ether)s bearing phthalazinone moiety

A novel series of phthalazinone-based poly(arylene ether nitrile)s bearing terminal cyano groups via N-C linkages (PPEN-DCs) were synthesized by a simple solution polycondensation of 4-(4-hydroxylphenyl)(2H)-phthalazin-1-one (HPPZ) with calculated 2,6-difluorobenzonitrile (DFBN), followed by the termination of 4-chlorobenzonitrile (CBN). The M_ns of oligomeric PPEN-DCs, which are in the range of 1600-6200, can be well-controlled by adjusting reactant ratio. The incorporation of phthalazinone into the polymer chain results in an improvement in the solubility and glass transition temperatures (T_gs). The amorphous PPEN-DCs were thermally crosslinked to afford insoluble products in the presence of terephthalonitrile and zinc chloride. The pendant cyano groups in the polymer chain hardly undergo any crosslinking or cyclization, while the terminal cyano groups with nitrogen-bridged phthalazinone in the para-substitution are much more reactive in s-triazine forming reaction and effectively promote certain crosslinking under normal pressure. T_gs of the oligomers, which range from 245 to 269 °C, could be further increased at least by 94 °C upon thermal curing. The crosslinked samples exhibit excellent thermal stability and absorb less than 2.7 wt% water after exposure to an aqueous environment for extended periods. This kind of cyano-terminated poly(arylene ether nitrile)s may be a good candidate as matrix resins for high-performance polymeric materials.     

Microstructure and rheological properties of thermo-responsive poly(N-isopropylacrylamide) microgels

The microstructure and rheological properties of thermo-responsive poly(N-isopropylacrylamide) (PNIPAM) microgels cross-linked with methylenebis-acrylamide (BA) were examined by dynamic light scattering and rheological techniques. As the temperature was increased from 10 to 50 °C, the particles diameter decreased by approximately two times near the volume phase transition temperature, T_v of between 30 and 35 °C. The addition of salt to the microgel dispersion provides competition for the water molecules hydrating the PNIPAM chains thus weakening the PNIPAM-H₂O hydrogen bonds and the microgel progressively deswelled. The validity and limitation of the semi-empirical approach to model charged soft microgel particles developed previously were tested on this thermo-responsive system. A variable specific volume, k was introduced to convert the mass concentration to effective volume fraction. With increasing concentration, inter-particle repulsive force was enhanced, which overcame the osmotic force inside the soft particle, resulting in the expulsion of solvent from the swollen particles, and the particle shrank. The viscosity data for PNIPAM microgels at varying solution temperatures and ionic strength showed excellent agreement with the modified Krieger-Dougherty (K-D) model.     

Crosslinkable poly(aryl ether ketone)s containing pendant phenylethynyl moieties: Synthesis, characterization and properties

A novel phenylethynyl-contained bisphenol monomer, (2,5-dihydroxyphenyl)(4-(2-phenylethynyl)phenyl)methanone (PEBP), has been synthesized and characterized. The resultant monomer was copolymerized with hydroquinone and 4,4′-difluorobenzophenone by means of an aromatic nucleophilic substitution reaction to provide a series of crosslinkable poly(aryl ether ketone)s containing pendant phenylethynyl moieties (PE-PAEKs). The solubility of PE-PAEKs tended to be improved with the increase in PEBP content. Wide-angle X-ray diffraction (WAXD) results showed that introduction of bulky pendant groups into molecular chains led to decrease in crystallinity. PE-PAEKs were successfully cured upon heating. Dynamic mechanical analysis (DMA) results indicated that the glass-transition temperature (T_g) of the cured PE-PAEKs was increased. Thermogravimetric analysis (TGA) results implied that the thermal stability of the cured PE-PAEKs was excellent.     

Synthesis and properties of poly(amide-imide)s based on 1,5-bis(4-trimellitimido)naphthalene

1,5-Bis(4-trimellitimido)naphthalene (II) was prepared by the condensation reaction of 1,5-naphthalenediamine and trimellitic anhydride. A series of aromatic poly(amide-imide)s (IV _a–o) was synthesized by the direct polycondensation of the diimide-diacid (II) and various aromatic diamines (III _a–o). The reaction utilized triphenyl phosphite and pyridine as condensing agents in the presence of calcium chloride in N-methyl-2-pyrrolidone (NMP). The inherent viscosities of the resulting poly(amide-imide)s were in the range of 0.55∼1.39 dL/g. These polymers were generally soluble in polar solvents, such as N,N-dimethylacetamide (DMAc), NMP, N,N-dimethylformamide (DMF). Flexible and tough poly(amide-imide) films were obtained by casting from a DMAc solution and had tensile strengths of 90∼145 MPa, elongations to break of 5∼13 %, and initial moduli of 2.29∼3.73 GPa. The glass transition temperatures of some poly(amide-imide)s were recorded in the range of 206∼218 °C, and most of the polymers did not show discernible glass transition on their DSC traces. The 10% weight loss temperatures were above 522 °C in nitrogen and above 474 °C in air atmosphere.     

Crosslinkable fully aromatic poly(aryl ether ketone)s bearing macrocycle of aryl ether ketone

A novel bisphenol monomer, (3-methoxy)phenylhydroquinone, was synthesized via a three-step synthetic procedure. The cyclization of the bisphenol monomer and 4,4-difluorobenzophenone was carried out under pseudo high dilution condition. Two types of fully aromatic poly(aryl ether ketone)s were prepared by copolymerization of macrocycle of aryl ether ketone (MACEK) containing hydroxyphenyl, 4,4′-(hexafluoroisopropylidene)diphenol (HFBPA), and 4,4-difluorobenzophenone. The copolymers have high molecular mass, good solubility and high glass transition temperatures. The copolymers are crosslinkable in the presence of basic initiator and the glass transition temperatures of the copolymers increased greatly after the curing. These cured copolymers exhibit excellent thermal stability, and the 5% weight loss temperatures are around 500 °C in nitrogen.     

Bio-degradable vegetable oil based hyperbranched poly(ester amide) as an advanced surface coating material

Vegetable oil based hyperbranched poly(ester amide) (HBPEA) has enormous importance because of its unique characteristics. Thus the synthesis of HBPEA using N,N′-bis(2-hydroxy ethyl) castor oil fatty amide, maleic anhydride, phthalic anhydride and isophthalic acid as A₂ monomers and diethanol amine, as B₃ monomer was reported for the first time. The chemical structure of the synthesized resin was characterized by Fourier transform infrared (FTIR) and nuclear magnetic resonance (¹H NMR and ¹³C NMR) spectroscopic techniques. The degree of branching (DB) (as vouched by ¹H NMR analysis) and initial degradation temperature were found to increase with the increment in B₃ monomer content. Resins with 5 and 10 wt% of B₃ monomer showed shear thinning behavior while rheopectic nature of HBPEA with 15 wt% of B₃ content was observed. The evaluation of tensile strength, elongation at break, abrasion resistance, adhesion strength, scratch hardness, gloss, impact strength and chemical resistance complemented by microbial and lipolytic degradation forward the epoxy cured thermosets as advanced biodegradable surface coating materials.     

Formulation and performance evaluation of hydroxyl terminated hyperbranched polyesters based poly (ester–urethane–urea) coatings on mild steel

A low molecular weight, anticorrosive hyperbranched poly (ester–urethane–urea) [HB-P(EUU)] coatings were formulated using 2nd generation hydroxyl terminated hyperbranched polyesters (OH–HBPEs), isophorone di-isocyanate (IPDI) as a cross linking agent and dibutyltin dilaurate (DBTDL) as a catalyst with certain additives. First, NCO terminated prepolymers (HBPEUs) were formulated by reacting OH–HBPEs with IPDI at NCO:OH ratio of 1.1:1 for 4 h at 70–80 °C, then HBPEUs were mixed with DBTDL and various additives and finally coated on pretreated cold rolled mild steel (MS) substrates by dip coating method. Before applying on MS substrates, viscosity and volume solid of coatings were measured. The molecular structure of HBPEUs was characterized by ATR-FTIR and ¹H NMR analysis. Surface morphology of coated panels was characterized by atomic force microscopy (AFM) and found that coating components were homogeneously distributed and surface was smooth and crack free. Performance of coated substrates was evaluated by various tests such as cross hatch and pull off adhesion, abrasion resistance, scratch resistance, impact resistance, flexibility, and pencil hardness. UV stability of coated substrates was evaluated by UV-whether-o-meter and corrosion resistance property was evaluated by salt spray, humidity, polarization and electrochemical impedance (EIS) test. Results were also compared with polyurethane coating based on linear polyester. HB-P(EUU) coatings showed excellent enhancement in mechanical, durability as well as corrosion resistance properties than their linear counterpart.     

Scope in the synthesis and properties of poly(ether imide)s

This paper reviews methods of synthesis of dianhydrides for use in poly(ether imide) syntheses. It discusses the synthesis of new dianhydrides from alkyl-substituted diols, catechol and its derivatives and dihydroxynaphthalenes and the synthesis of new poly(ether imide)s from them. The major features of the properties of these groups of polymers, especially those of highly processable poly(ether imide)s, are discussed and potential applications are considered.     

Synthesis and characterization of poly (amide-imide-imide)s based on diacids with bulky m-chloro phenyl moiety and rigid pyridine moiety

A series of novel aromatic diamines containing kinked m-chloro phenyl moiety was synthesized by the reaction of m-chloro benzaldehyde with 2,6-dimethyl aniline. The tetraimide diacid was synthesized by using the prepared diamine with benzophenone tetracarboxylic acid dianhydride (BPTDA) and p-amino benzoic acid. The polymers were prepared by treating the tetraimide diacid with different aromatic diamines. The structures of the monomers and polymers were identified by ¹H-NMR, FTIR,¹³C-NMR and elemental analysis. The polymers showed excellent thermal stability, solubility and mechanical properties. Their structure–property relationship was studied by comparing these m-chloro polymers with polymers containing rigid Pyridine moiety.     

Temperature responsive bio-compatible polymers based on poly(ethylene oxide) and poly(2-oxazoline)s

This review covers the LCST behavior of two important polymer classes in aqueous solution, namely poly(2-oxazoline)s and systems whose thermo-responsiveness is based on their structural similarity to poly(ethylene oxide) (PEO). In order to elucidate the progress that has been made in the design of new thermo-responsive copolymers, experimental data that were obtained by different research groups are compared in detail. Copolymerization with hydrophilic or hydrophobic comonomers represents a suitable method to tune the coil to globule transition temperature of several homopolymers, and incorporation of other monomers provided further interesting features, such as pH responsiveness or sensing properties. In addition, living and controlled polymerization techniques enabled access to defined end groups and more advanced polymer architectures, such as graft copolymers or double responsive block copolymers. The effect of such structural variations on the temperature responsive behavior of the (co)polymers is discussed in detail.     

Facile preparation of highly luminescent CdTe quantum dots within hyperbranched poly(amidoamine)s and their application in bio-imaging

A new strategy for facile preparation of highly luminescent CdTe quantum dots (QDs) within amine-terminated hyperbranched poly(amidoamine)s (HPAMAM) was proposed in this paper. CdTe precursors were first prepared by adding NaHTe to aqueous Cd²⁺ chelated by 3-mercaptopropionic sodium (MPA-Na), and then HPAMAM was introduced to stabilize the CdTe precursors. After microwave irradiation, highly fluorescent and stable CdTe QDs stabilized by MPA-Na and HPAMAM were obtained. The CdTe QDs showed a high quantum yield (QY) up to 58%. By preparing CdTe QDs within HPAMAM, the biocompatibility properties of HPAMAM and the optical, electrical properties of CdTe QDs can be combined, endowing the CdTe QDs with biocompatibility. The resulting CdTe QDs can be directly used in biomedical fields, and their potential application in bio-imaging was investigated.     

Synthesis and characterization of poly(tetramethylsilarylenesiloxane) derivatives bearing benzodithiophene moieties

Poly(tetramethylsilarylenesiloxane) derivatives bearing benzo[1,2-b;4,5-b′]dithiophene (P1) and benzo[2,1-b;3,4-b′]dithiophene (P2) moieties were prepared via polycondensation of the corresponding disilanol monomers, that is, 2,6-bis(dimethylhydroxysilyl)benzo[1,2-b;4,5-b′]dithiophene (M1) and 2,7-bis(dimethylhydroxysilyl)benzo[2,1-b;3,4-b′]dithiophene (M2), respectively. It was deduced that P1 is a crystalline polymer while P2 is an amorphous one from the results of differential scanning calorimetry (DSC). Bathochromic and hyperchromic effects were observed in the absorption and fluorescence spectra when dimethylsilyl substituents were introduced on the benzo[1,2-b;4,5-b′]dithiophene and benzo[2,1-b;3,4-b′]dithiophene skeletons. The fluorescence quantum yields (Φ_Fs) were not improved by the introduction of dimethylsilyl groups onto the benzo[1,2-b;4,5-b′]dithiophene and benzo[2,1-b;3,4-b′]dithiophene skeletons, whereas the improvement in the Φ_Fs was remarkable in the case of poly(tetramethylsilarylenesiloxane) derivatives that possessed the corresponding fused benzene ring systems, i.e., poly(tetramethyl-2,6-silanthrylenesiloxane) and poly(tetramethyl-1,8-silphenanthrylenesiloxane).