1.48μm掺饵光纤放大器泵源

采用Ｐ型ＩｎＰ衬底新月型结构制备了１．４８μｍ大功率激光器，该激光器与单模光纤耦合输出功率大于４０ｍＷ。     

1.48μm大功率GaInAsP／InP激光器

用两步液相外延法研制出１．４８μｍ大功率ＧａＩｎＡｓＰ／ＩｎＰ激光器，尾纤输出功率大于３０ｍＷ。用作掺铒光纤放大器的泵浦光源，双向泵浦小信号增益２８ｄＢ，经较长时间的实际运行，表明器件性能稳定可靠，温度特性好。     

980nm InGaAs／GaAs／AlGaAs应变量子阱激光器

报导了脊形波导ＩｎＧａＡｓ／ＧａＡｓ／ＡｌＧａＡｓ应变量子阱激光器的特性和实验结果，激光器阀值电流最低为９ｍＡ，典型值为１５ｍＡ，线性输出光功率大地１２０ｍＷ，微分量子效率典型值为６０％，５０℃，８０ｍＷ恒定功率条件下老化实验结果表明；该条件下激光器寿命超过１０００小时。     

5GHz主动锁模光纤激光器

在国内首次研制成功半导体激光器泵浦的主动锁模掺饵光纤激光器，器件利用高速ＬｉＮｂＯ３幅度调制器，重复频率达５ＧＨｚ脉宽２４ｐｓ，峰值功率为２．５毫瓦，波长约为１．５５２μｍ。     

LD泵浦Nd：YVO4内腔倍频激光器获得120mW绿光连续输出

利用半导体激光器（ＬＤ）端面泵浦Ｎｄ：ＹＶＯ＿４和用ＫＴＰ内腔倍频的绿激光器获得了１２０ｍＷ连续、稳定的５３２ｎｍ绿激光输出。泵浦阈值Ｐ＿（ｔｈ）＝１６０ｍＷ，光－光转换效率η＿ｓ＝８．１％。换用激光腔输出耦合镜，在不加ＫＴＰ晶体倍频时，可连续输出１．０６μｍ的红外激光，输出功率为４５０ｍＷ，光－光转换效率为３１％。     

用于掺铒光纤放大器泵浦源的高性能980nm InGaAs应变量子阱激光器

利用分子束外延方法研制出了高质量的ＩｎＧａＡｓ／ＡｌＧａＡｓ庆变量子阱激光器外延材料，其最低的阈值电流密度可达到１２０Ａ／ｃｍ＾２，激光波长在９８０ｎｍ左右。获得了高性能的适合于掺铒光纤放大器用的９８０ｎｍ量子阱激光器泵浦源，其典型的阈值电流为１５ｍＡ，外微分量子效率的典型值和最好值分别为０．８ｍＷ／ｍＡ和１．０ｍＷ／ｍＡ，线性输出功率大于１２０ｍＷ，在２０℃－５０℃的特征温度Ｔ０为１２５Ｋ。器件     

偏频锁定0.633μM碘吸收稳频激光

为了满足大尺寸精密干涉测量对干涉信号的信噪比要求，我们研制了偏频锁定氦氖０．６３３μｍ碘吸收稳频激光器，该系统激光的频率不稳定度为５．５×１０－１２（τ＝１０ｓ），系统的频率再现性为４×１０－１１，可连续锁定６个小时以上，无调制输出功率大于０．８ｍＷ。     

色散渐减光纤压缩光脉冲

利用色散补偿光纤（ＤＣＦ）及色散位移光纤（ＣＳＦ）压缩重复频率为２．５ＧＨｚ的增益开关量子阱ＤＦＢ半导体激光器出射的光脉冲，将光脉冲由５３．８ｐｓ压缩至２．５ｐｓ，而后利用色散渐减光纤将２．５ｐｓ的光脉冲进一步压缩至０．８３ｐｓ。     

60瓦半导体激光器光纤耦合器件

应用光纤列阵耦合方式，对大功率半导体激光器线列阵输出光束的快轴方向用一根柱透镜准直，准直后的光束耦合到光纤列阵中，实现出纤功率为60瓦的大功率半导体激光二极管线列阵光纤耦合器件，耦合效率大于80％，光纤的数值孔径NA为0．11。     

光缆CATV用DFB激光器发射组件

介绍了国内首次研制的光缆ＣＡＴＶ用１．３μｍＤＦＢ激光器组件。组件工作频带达到１ＧＨｚ，带内起伏〈１ｄＢ，组件的ＲＩＮ〈－１５３ｄＢ／Ｈｚ；出纤光功率〉２ｍＷ，载噪比ＣＮＲ〉５０ｄＢ。首次实现用低反射尖锥端光纤的ＤＦＢ激光器耦合。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...