Constitutive Model for Time-Dependent Behavior of FRP–Concrete Interface

A fundamental understanding of fiber-reinforced polymer (FRP) laminate bonding behavior, including bond strength and effective bonding length, is of primary importance for the development of design guidelines and codes for concrete structures strengthened with externally bonded FRP reinforcement as a bond-critical application. However, the long-term serviceability of such FRP-strengthened structures is still a concern due to a lack of both long-term performance data and a suitable model to represent these performances. This study aims at presenting a viscoelastic model describing the time-dependent behavior of the FRP–concrete interface. The proposed model has been calibrated using strain measurements of the designed specimen for the experimental investigation of the time-dependent behavior of the FRP–concrete interface, including the development of the effective bonding length. Afterward, the proposed model satisfactorily predicts the time-dependent bonding length of the FRP sheet in comparison with the experimental results. The effects, both of creep of the adhesive layer and of creep and shrinkage of the concrete, on the changes in the effective bonding length of the PFRP sheet are also discussed.     

Flexural Fatigue Behavior of Reinforced Concrete Beams Strengthened with FRP Fabric and Precured Laminate Systems

Rehabilitation of existing structures with carbon fiber reinforced polymers (CFRP) has been growing in popularity because they offer resistance to corrosion and a high stiffness-to-weight ratio. This paper presents the flexural strengthening of seven reinforced concrete (RC) beams with two FRP systems. Two beams were maintained as unstrengthened control samples. Three of the RC beams were strengthened with CFRP fabrics, whereas the remaining two were strengthened using FRP precured laminates. Glass fiber anchor spikes were applied in one of the CFRP fabric strengthened beams. One of the FRP precured laminate strengthened beams was bonded with epoxy adhesive and the other one was attached by using mechanical fasteners. Five of the beams were tested under fatigue loading for two million cycles. All of the beams survived fatigue testing. The results showed that use of anchor spikes in fabric strengthening increase ultimate strength, and mechanical fasteners can be an alternative to epoxy bonded precured laminate systems.     

Experimental Investigation of the Influence of Moisture on the Bond Behavior of FRP to Concrete Interfaces

The effects of moisture on the initial and long-term bonding behavior of fiber reinforced polymer (FRP) sheets to concrete interfaces have been investigated by means of a two-year experimental exposure program. The research is focused on the effects of (1) moisture at the time of FRP installation, in this paper termed “construction moisture,” consisting of concrete substratum surface moisture and external air moisture; and (2) moisture, in this paper termed “service moisture,” which normally varies throughout the service life of concrete. Concrete beams with FRP bonded to their soffits were prepared. Before bonding, concrete substrates were preconditioned with different moisture contents and treated with different primers. The FRP bonded concrete beams were then cured under different humidity conditions before being subjected to combined wet/dry (WD) and thermal cycling regimes to accelerate the exposure effects. Adhesives with different elastic moduli were used to investigate the long-term durability of each adhesive when subjected to accelerated WD cycling. Pull-off tests and bending tests were conducted at the beginning of the cycling and then again after 8 months, 14 months, and 2 years of exposure so as to evaluate the tensile and shear performance of the FRP-to-concrete interfaces. It was found that the effect of the concrete substrate moisture content on short-term interfacial bond performance could be eliminated if an appropriate primer was used. All FRP-to-concrete bonded joints failed at the interface between the primer and concrete after exposure while those not exposed usually failed within the concrete substrate. After exposure to an environment of accelerated WD cycles, it was also found that the interfacial tensile bond strength degraded asymptotically with the exposure time while the flexural capacity of the FRP sheet bonded plain concrete beams even increased. The mechanism behind the above, which is an apparently contradictory phenomenon, is discussed.     

Effect of Concrete Composition on FRP/Concrete Bond Capacity

External bonding of fiber-reinforced plastics (FRP) to concrete members has been established as an efficient and effective method for structural strengthening and retrofitting. Direct shear test is often employed to study the crack-induced debonding failure in reinforced concrete members flexurally strengthened with FRP composites. In many existing models, the bond capacity (which defines ultimate load capacity of the specimen in the direct shear test) is considered to be strongly dependent on the compressive or tensile strength of the concrete. However, since debonding behavior is affected by interfacial friction due to aggregate interlocking within the debonded zone, the concrete composition should also play an important role in determining the bond capacity. In this study, the direct shear test is performed with 10 different compositions of concrete. The test results indicate that the bond capacity has little correlation with either the concrete compressive or splitting tensile strength. On the other hand, the bond capacity is found to have reasonable correlation with the concrete surface tensile strength but correlates very well with the aggregate content. As a geometry independent parameter corresponding to bond capacity, the interfacial fracture energy is empirically proposed to relate to these two parameters. The consideration of aggregate content leads to much better agreement between predicted bond capacity and test result. Hence, the effect of concrete composition on the FRP/concrete bond should be considered in practical design.     

Experimental Investigation and Fracture Analysis of Debonding between Concrete and FRP Sheets

The last few years have witnessed a wide use of externally bonded fiber reinforced polymer (FRP) sheets for strengthening existing reinforced and prestressed concrete structures. The success of this strengthening method relies on the effectiveness of the load-transfer between the concrete and the FRP. Understanding the stress transfer and the failure of the concrete–FRP interface is essential for assessing the structural performance of strengthened beams and for evaluating the strength gain. This paper describes an experimental investigation of the interfacial bond behavior between concrete and FRP. The strain distributions in concrete and FRP are determined using an optical technique known as digital image correlation. The results confirm that the debonding process can be described in terms of crack propagation through the interface between concrete and FRP. The data obtained from the analysis of digital images was used to determine the interfacial material behavior for the concrete–FRP interface (stress versus relative displacement response) and the fracture parameter GF (fracture energy). The instability in the test response at failure is shown to be the result of snapback, which corresponds with the elastic unloading of the FRP as the load carrying ability of the interface decreases with increasing slip.     

Flexural Strength of RC Beams with GFRP Laminates

The results of an experimental and numerical study of the flexural behavior of reinforced concrete beams strengthened with glass-fiber-reinforced-polymer (GFRP) laminates are presented in this paper. In the experimental program, ten strengthened beams and two unstrengthened beams are tested to failure under monotonic loading. A number of external GFRP laminate layers and bond length of GFRP laminates in shear span are taken as the test variables. Longitudinal GFRP strain development and interfacial shear stress distribution from the tests are examined. The experimental results generally showed that both flexural strength and stiffness of reinforced concrete beams could be increased by such a bonding technique. In the numerical study, an eight-node interface element is developed to simulate the interface behavior between the concrete and GFRP laminates. This element is implemented into the MARC software package for the finite-element analyses of GFRP laminate strengthened reinforced concrete beams. Reasonably good correlations between experimental and numerical results are achieved.     

Interfacial Behavior and Debonding Failures in FRP-Strengthened Concrete Slabs

It has been demonstrated, through laboratory investigations and various field projects, that the external bonding of fiber- reinforced polymer (FRP) laminates is an effective technique for the structural enhancement of reinforced concrete slabs. In such applications, failure is generally governed by debonding of the FRP laminate. Nevertheless, numerical simulations to date of FRP-strengthened slabs have usually been based on the assumption of full bond between the concrete and FRP. In this study, the interfacial behavior between the FRP laminates and the concrete substrate is accounted for by introducing appropriate bond-slip models for the interface in a nonlinear finite-element analysis of FRP-strengthened two-way slabs. The numerical model is capable of simulating slabs strengthened in shear or in flexure; it can be applied to arbitrary FRP configurations, and can also accommodate both passive as well as prestressed FRP strengthening schemes. Results are presented in terms of load-deflection relationships, ultimate load capacities, failure modes, and interfacial slip and stress distributions. When compared to test results reported in the literature, the analysis is shown to lead to excellent predictions in that, for the entire set of FRP-strengthened specimens considered, the average of the numerical-to-experimental load capacity ratios is 0.966, with a standard deviation of 0.066. Furthermore, in all cases when FRP debonding was observed experimentally, the analysis correctly predicted the mode of failure.     

Flexural Strengthening of Reinforced Concrete Beams by Mechanically Attaching Fiber-Reinforced Polymer Strips

The current method of bonding fiber-reinforced polymer (FRP) strengthening strips to concrete structures requires extensive time and semiskilled labor. An alternative method is to use a commercial off-the-shelf powder-actuated fastening system to attach FRP strips to concrete. A series of flexural tests were conducted on 15 304.8×304.8×3,657.6?mm (12×12×144?in.) reinforced concrete beams. Two beams were tested unstrengthened, 12 were strengthened with mechanically fastened FRP strips, and one was strengthened with a bonded FRP strip. The effects of three different strip moduli, different fastener lengths and layouts, and predrilling were examined. Three of the beams strengthened with mechanically attached FRP strips showed strengthening comparable to the beam strengthened with a bonded FRP strip. The same three beams strengthened with mechanically attached FRP strips also showed a greater ductility than the beam strengthened with a bonded FRP strip.     

Development of the Nonlinear Bond Stress–Slip Model of Fiber Reinforced Plastics Sheet–Concrete Interfaces with a Simple Method

A new analytical method for defining the nonlinear bond stress–slip models of fiber reinforced plastics (FRP) sheet–concrete interfaces through pullout bond test is proposed. With this method, it is not necessary to attach many strain gauges on the FRP sheets for obtaining the strain distributions in FRP as well as the local bond stresses and slips. Instead, the local interfacial bond stress-slip models can be simply derived from the relationships between the pullout forces and loaded end slips. Based on a series of pullout tests, the bond stress–slip models of FRP sheet–concrete interfaces, in which different FRP stiffness, FRP materials (carbon FRP, aramid FRP, and glass FRP), and adhesives are used, have been derived. Only two parameters, the interfacial fracture energy and interfacial ductility index, which can take into account the effects of all interfacial components, are necessary in these models. Comparisons between analytical results and experimental ones show good accordance, indicating the reliability of the proposed method and the proposed bond stress–slip models.     

Prediction of Interfacial Bond Failure of FRP–Concrete Surface

The use of fiber-reinforced polymer (FRP) for strengthening concrete structures has grown remarkably during the past few years. In spite of exhibiting superior properties, the safety of usage is questionable as FRP undergoes brittle debonding failure. The aim of this study is to review and compare the existing research on bond failure between FRP and concrete substrates. Among the different failure modes, there has been little research in terms of intermediate crack-induced interfacial debonding and fewer strength models are developed for predicting such failures. Conducting a simple shear test on the FRP bonded to a concrete substrate can simulate this type of failure mode. Twelve specimens were tested to study the influence of concrete strength and the amount of FRP on the ultimate load capacity of a FRP–concrete bond under direct shear. Existing experimental work was collected from the literature and consists of an extensive database of 351 concrete prisms bonded to FRP and tested in direct shear tests. The analytical models from various sources are applied to this database and the results are presented.     

ESPI Measurement of Bond-Slip Relationships of FRP-Concrete Interface

Fiber-reinforced polymer (FRP) composites are widely used for strengthening reinforced concrete structures because of their superior properties. Reliable performance of the bond between the external FRP and the concrete in maintaining the composite action between them is crucial for this strengthening technique to be effective. To fully understand and model this bond behavior, a rigorous bond-slip law is essential. This paper presents an experimental study in which the displacement fields in a carbon fiber-reinforced polymer (CFRP)-to-concrete double shear test were measured using the nondestructive and noncontact electronic speckle pattern interferometry (ESPI) technique. Full-field in-plane displacements were measured in 33 CFRP specimens with concrete strengths varying from 23 to 69?MPa. The measurement results were used to infer the bond-slip behavior between the FRP and the concrete. The inferred bond-slip curves include a nonlinear ascending branch and a descending branch. The strength of concrete is found to have significant effect on the peak bond stress but little effect on the slip corresponding to the peak bond stress. A logarithmic model and a simpler parabolic model are proposed to represent the experimental bond-slip constitutive curves.     

Bond Between Near-Surface Mounted Carbon-Fiber-Reinforced Polymer Laminate Strips and Concrete

In recent years, a strengthening technique based on near-surface mounted (NSM) laminate strips of carbon-fiber-reinforced polymer (CFRP) has been used to increase the load-carrying capacity of concrete and masonry structures by introducing laminate strips into precut grooves on the concrete cover of the elements to be strengthened. The high experimentally derived levels of strength efficacy with concrete columns, beams, and masonry panels have presented NSM as a viable and promising technique. This practice requires no surface preparation work and, after cutting the groove, requires minimal installation time compared to the externally bonded reinforcing technique. A further advantage associated with NSM CFRP is its ability to significantly reduce the probability of harm resulting from fire, acts of vandalism, mechanical damage, and aging effects. To assess the bond behavior of CFRP to concrete, pullout-bending tests have been carried out. The influences of bond length and concrete strength on bond behavior are analyzed, the tests are described, and the results are presented and discussed in detail. Finally, a local stress-slip relationship is determined based on both experimental results and a numerical strategy.     

Shape Effect on the Performance of Carbon Fiber Reinforced Polymer Wraps

At present, fiber reinforced polymer (FRP) composite materials are extensively used to strengthen concrete structures and a main application is wrapping compression members such as building and bridge columns for improved strength and ductility. In this case, FRP laminates are intended to provide confinement to the concrete and the cross section shape plays an important role on the effectiveness of the method. The primary purpose of this paper is to introduce a test device and a test method designed to determine the effect of corner radius on the strength of the FRP laminate and on the distribution of the resulting radial stress on the substrate material. Various curvatures were investigated. In the proposed device, they can be realized by using interchangeable inserts. Strain distribution around the corner, failure load, and failure mode of the FRP laminate were monitored and analyzed. The stress concentration in the laminate is studied numerically using the finite element method and compared with experimental results. The relationship between radial stress distribution and corner radius is determined to provide guidance in practical cases.     

Flexural and Interfacial Behavior of FRP-Strengthened Reinforced Concrete Beams

Although there is a large amount of experimental data available on the fiber-reinforced polymer (FRP) strengthening of concrete structures, a full understanding of the various debonding phenomena is somewhat lacking. As a contribution to fill this need, two-dimensional and three-dimensional (3D) nonlinear displacement-controlled finite-element (FE) models are developed to investigate the flexural and FRP/concrete interfacial responses of FRP-strengthened reinforced concrete beams. Interface elements are used to simulate the FRP/concrete interfacial behavior before and after cracking. The analysis is carried out using two different relations for the interface; namely, nonlinear and bilinear bond–slip laws. The results predicted using these two laws are compared to those based on the full-bond assumption. The FE models are capable of simulating the various failure modes, including debonding of the FRP, either at the plate end or at intermediate cracks. The 3D model is created to accommodate cases of FRP-strengthened reinforced concrete beams utilizing FRP anchorage systems. In addition, the models successfully represent the actual interfacial behavior at the vicinities of cracks including the stress/slip concentrations and fluctuations. Results are presented in terms of the ultimate load carrying capacities, failure modes and deformational characteristics. Special emphasis is placed on the FRP/concrete interfacial behavior and cracking of the concrete. The numerical results are compared to available experimental data for 25 specimens categorized in six series, and they show a very good agreement.     

Bonding Characteristics of Fiber-Reinforced Polymer Sheet-Concrete Interfaces under Dowel Load

Based on a series of experimental tests on notched concrete beams externally bonded with unidirectional fiber-reinforced polymer (FRP) sheets, this paper investigates the bond characteristics of FRP sheet-concrete interfaces under dowel load, which acts vertically on the FRP sheet and leads to a mix-mode interface peeling. The peeling properties of FRP sheet-concrete interfaces under the dowel load are evaluated in terms of their interface dowel load-carrying capacity, critical interface peeling angle, and interface peeling fracture energy. Experimental parameters include strength of concrete substrate, tension stiffness of FRP sheets, properties of bonding adhesives, concrete surface treatment methods, and length of precrack set between the FRP sheet and concrete substrate. Analytical models clarifying the relationships among the interface dowel load-carrying capacity, the interface peeling angle, and the interface peeling fracture energy are built up and also verified by test results. Further, this paper shows how to use the interface peeling fracture energy calibrated from the present dowel tests for the practical design of spalling prevention, which is now becoming a popular application of FRP sheets for the maintenance and repair of existing concrete structures in Japan.     

Investigation of Bond in Concrete Structures Strengthened with Near Surface Mounted Carbon Fiber Reinforced Polymer Strips

Fiber reinforced polymer (FRP) materials are currently produced in different configurations and are widely used for the strengthening and retrofitting of concrete structures and bridges. Recently, considerable research has been directed to characterize the use of FRP bars and strips as near surface mounted reinforcement, primarily for strengthening applications. Nevertheless, in-depth understanding of the bond mechanism is still a challenging issue. This paper presents both experimental and analytical investigations undertaken to evaluate bond characteristics of near surface mounted carbon FRP (CFRP) strips. A total of nine concrete beams, strengthened with near surface mounted CFRP strips were constructed and tested under monotonic static loading. Different embedment lengths were used to evaluate the development length needed for effective use of near surface mounted CFRP strips. A closed-form analytical solution is proposed to predict the interfacial shear stresses. The model is validated by comparing the predicted values with test results as well as nonlinear finite element modeling. A quantitative criterion governing the debonding failure of near surface mounted CFRP strips is established. The influence of various parameters including internal steel reinforcement ratio, concrete compressive strength, and groove width is discussed.     

Modeling Debonding Failure in FRP Flexurally Strengthened RC Members Using a Local Deformation Model

Reinforced concrete (RC) beams and slabs can be strengthened by bonding fiber-reinforced polymer (FRP) composites to their tension face. The performance of such flexurally strengthened members can be compromised by debonding of the FRP, with debonding initiating near an intermediate crack (IC) in the member away from the end of the FRP. Despite considerable research over the last decade, reliable IC debonding strength models still do not exist. The current paper attempts to correct this situation by presenting a local deformation model that can simulate IC debonding. The progressive formation of flexural cracks, and the associated crack spacings and crack widths are modelled from initial cracking to the onset of debonding. The bond characteristics between the longitudinal steel reinforcement and concrete, and the FRP and concrete, as well as the tension stiffening effect of the reinforcement and FRP to the concrete, are considered. The FRP-to-concrete bond-slip relation is used to determine the onset of debonding. The analytical predictions compare well with experimental results of FRP-strengthened RC cantilever slabs.     

Peeling Behavior and Spalling Resistance of Bonded Bidirectional Fiber Reinforced Polymer Sheets

This paper presents the peeling behavior and spalling resistant effect of bidirectional fiber reinforced polymer (FRP) sheets externally bonded to concrete surfaces. Experimental investigations are carried out through a series of newly designed punching-peeling tests. A wide range of variables, such as FRP sheet layers and fiber direction, plate constraint, concrete strength, adhesives, bond length of FRP sheets, diameter of indenter, and types of fibers, are considered in the experimental investigation. Theoretical study is also conducted for the specimens. Interfacial fracture energy is calculated analytically using a membrane-peeling method. It is realized that only two material parameters, i.e., the interfacial fracture energy of the FRP-concrete interface and the tensile stiffness of FRP sheets, are necessary to represent the interfacial spalling resistant behavior. Finally, the theoretical results are validated by comparing with experimental results. Comparison of theoretical to experimental results shows that the proposed theoretical model is satisfactory in reasonably and accurately predicting the peeling behavior and spalling resistant capacity of bidirectional FRP sheets bonded to concrete surface.     

Comparison of Three Flexural Retrofit Systems under Monotonic and Fatigue Loads

The majority of experimental work involving the flexural retrofit of concrete bridge girders has been conducted on beam specimens with adhesive-applied, soffit-mounted, fiber-reinforced polymer (FRP) composite systems, referred to in this study as conventional adhesive application (CAA). It has been observed that the performance of such girders is often controlled by the quality of the bond between the FRP and the concrete substrate and the substrate’s ability to transfer stress from the steel to the FRP. With the goal of improving the performance of bonded FRP in mind, two additional soffit-mounted retrofit schemes are investigated: near-surface mounted (NSM), where the FRP strips are embedded in adhesive within slots cut into the substrate concrete, and, powder-actuated fastener-applied (PAF) FRP, which uses a powder-actuated nail gun to install mechanical fasteners through predrilled holes in the FRP into the concrete substrate, “nailing” the FRP in place. The PAF application is a recent development, and little work has been done on it other than by the proprietors of the system. This study reports on a comparative study of the static and fatigue performance of reinforced concrete beams retrofitted with CAA, NSM, and PAF FRP retrofit systems. Ten medium-scale beams were tested: six strengthened specimens, two per retrofit method, were tested under cyclic loading conditions, and four specimens, one per retrofit method and one control specimen, were tested monotonically to failure. The results of this study indicate that although all three methods of FRP application result in significant strength increases over the control specimen under monotonic loading conditions, the CAA method is outperformed by the other methods under cyclic conditions. A number of other relevant detailed conclusions with respect to performance and practical application issues are presented for each of the methods of retrofit examined in this study. Significantly, clear evidence of FRP debonding in the midspan region prior to specimen failure is presented.     

Experimental Behavior of Carbon Fiber-Reinforced Polymer (CFRP) Sheets Attached to Concrete Surfaces Using CFRP Anchors

Fiber-reinforced polymer (FRP) composite sheets have gained popularity as a viable strengthening technique for existing reinforced concrete structures. The efficiency of the strengthening system largely depends on adequate bond between FRP sheets and the concrete substrate. In recent years, techniques to anchor FRP sheets have been proposed in applications that have limited distance to develop FRP sheet strength. One promising technique consists of fabricating and bonding FRP anchors during the FRP sheet saturation and embedding them into predrilled holes in the concrete substrate. This paper presents experimental results highlighting the complex behavior between FRP sheets and anchors. The primary failure modes that the sheet-anchor system can experience are identified. The experiments identify the main variables that influence the FRP anchor-sheet system behavior. This research contributes to the needed experimental database that will aid in future development of design recommendations of this anchorage system.