Performance Evaluation of FRP Composite Deck Considering for Local Deformation Effects

We examine here the replacement of a deteriorated concrete deck in the historic Hawthorne Street Bridge in Covington, Va. with a lightweight fiber-reinforced polymer (FRP) deck system (adhesively bonded pultruded tube and plate assembly) to increase the load rating of the bridge. To explore construction feasibility, serviceability, and durability of the proposed deck system, a two-bay section (9.45 by 6.7?m) of the bridge has been constructed and tested under different probable loading scenarios. Experimental results show that the response of the deck is linear elastic with no evidence of deterioration at service load level (HS-20). From global behavior of the bridge superstructure (experimental data and finite- element analysis), degree of composite action, and load distribution factors are determined. The lowest failure load (93.6?kips or 418.1?kN) is about 4.5 times the design load (21.3?kips or 94?kN), including dynamic allowance at HS-20. The failure mode is consistent in all loading conditions and observed to be localized under the loading patch at the top plate and top flange of the tube. In addition to global performance, local deformation behavior is also investigated using finite-element simulation. Local analysis suggests that local effects are significant and should be incorporated in design criteria. Based on parametric studies on geometric (thickness of deck components) and material variables (the degree of orthotropy in pultruded tube), a proposed framework for the sizing and material selection of cellular FRP decks is presented for future development of design guidelines for composite deck structures.     

Laboratory and Field Performance of Cellular Fiber-Reinforced Polymer Composite Bridge Deck Systems

This paper addresses the laboratory and field performance of multicellular fiber-reinforced polymer (FRP) composite bridge deck systems produced from adhesively bonded pultrusions. Two methods of deck contact loading were examined: a steel patch dimensioned according to the AASHTO Bridge Design Specifications, and a simulated tire patch constructed from an actual truck tire reinforced with silicon rubber. Under these conditions, deck stiffness, strength, and failure characteristics of the cellular FRP decks were examined. The simulated tire loading was shown to develop greater global deflections given the same static load. The failure mode is localized and dominated by transverse bending failure of the composites under the simulated tire loading as opposed to punching shear for the AASHTO recommended patch load. A field testing facility was designed and constructed in which FRP decks were installed, tested, and monitored to study the decks’ in-service field performance. No significant loss of deck capacity was observed after more than one year of field service. However, it was shown that unsupported edges (or free edges) are undesirable due to transitional stiffness from approach to the unsupported deck edge.     

Modified Yield Line Theory for Full-Depth Precast Concrete Bridge Deck Overhang Panels

Full-depth precast deck slab cantilevers also referred to as full-depth precast concrete bridge deck overhang panels are becoming increasingly popular in concrete bridge deck construction. To date, no simple theory is able to estimate the overhang capacity of full-depth concrete bridge deck slabs accurately. Observations suggest that interaction between flexure and shear is likely to occur as neither alone provides an accurate estimate of the load-carrying capacity. Therefore, modified yield line theory is presented in this paper, which accounts for the development length of the mild steel reinforcing to reach yield strength. Failure of the full-depth panels is influenced by the presence of the partial-depth transverse panel-to-panel seam. When applying a load on the edge of the seam, the loaded panel fails under flexure while the seam fails in shear. Through the use of the modified yield line theory coupled with a panel-to-panel shear interaction, analytical predictions are accurate within 1–6% of experimental results for critical cases.     

Retrofit of a Three-Span Slab Bridge with Fiber Reinforced Polymer Systems—Testing and Rating

A 45-year old, three-span reinforced concrete slab bridge with insufficient capacity was retrofitted with 76.2- and 127-mm wide bonded carbon fiber-reinforced polymer (FRP) plates, 102-mm wide bonded carbon FRP plates with mechanical anchors at the ends, and bonded carbon FRP fabrics. The use of four systems in one bridge provided a unique opportunity to evaluate field installation issues and to examine the long-term performance of each system under identical traffic and environmental conditions. Using controlled truckload tests, the response of the bridge before retrofitting, shortly after retrofitting, and after one year of service was measured. The stiffness of the FRP systems was small in comparison to the stiffness of the bridge deck, and accordingly the measured deflections did not change noticeably after retrofitting. The measured strains suggest participation of the FRP systems, and more importantly, the strength of the retrofitted bridge was increased. A detailed 3D finite-element model of the original and retrofitted bridge was developed and calibrated based on the measured deflections. The model was used to predict more accurately the demands for computing the rating factors. The addition of FRP plates and fabrics led to a 22% increase in the rating factor and corresponding load limits. During a one-year period, traffic loading and environmental exposure did not apparently affect the performance of the FRP systems. The increased capacity and acceptable performance of the FRP systems enabled the engineers to remove the load limits in order to resume normal traffic. Future tests are necessary to monitor the long-term behavior of the FRP systems.     

Performance of Tube and Plate Fiberglass Composite Bridge Deck

A composite bridge deck system assembled from glass∕polyester pultruded components has been developed. This system utilizes square tubes running transverse to the traffic direction, mechanically fastened and bonded together, and flat cover plates bonded to the tubes with an epoxy adhesive and through-anchored to the deck support structure using mechanical connectors. A 4.27 × 1.22 m section of the deck system integrally connected to the superstructure at a 1.2 m girder spacing was tested to failure under a single patch loading. The results indicate a factor of safety of 4 on strength and a deflection-to-span ratio of about L∕300. Another section of the deck was fatigued to 3,000,000 cycles under service loading at a load ratio of R = 0.1 and a nominal frequency of 3 Hz. Results from these tests indicate no loss in stiffness up to 3,000,000 cycles. Following the fatigue testing, this section was also tested to failure; no loss in strength was observed. In addition, a finite-element model of the laboratory tests was developed. The results from the model showed good correlation to deflections and longitudinal strains measured during the tests.     

Flexural Performance of Carbon Fiber-Reinforced Polymer Prestressed Concrete Side-by-Side Box Beam Bridge

The effect of varying transverse posttensioning levels and arrangements on the load response of a one-half scale 30° skewed seven box beam bridge model was investigated. The effective span of the bridge model was 9.45?m (31?ft) with a width of 3.35?m (11?ft) and depth of 355.6?mm (14?in.). The bridge model was prestressed and reinforced with carbon fiber composite cables (CFCCs). CFCCs were also used as shear reinforcement. The bridge model was provided with five transverse diaphragms equally spaced along the length of the bridge. The experimental investigation included load and strain distribution tests and a flexural ultimate load test. The load and strain distribution tests were conducted on the bridge model with and without full-depth longitudinal cracks at the shear-key locations. The investigation showed that the application of an adequate transverse posttensioning force was successful in restoring the load distribution of the bridge model with full-depth longitudinal deck cracks to that of the case without deck cracks. The ultimate load and the associated compression-controlled failure mode of the bridge model agreed well with that predicted according to ACI 440.4R-04 and numerical analysis. The behavior of the bonded pretensioned and reinforced CFCC strands was linear elastic and remained intact throughout the collapse of the bridge model. The unbonded transverse posttensioned CFCC strand also remained intact.     

Experimental Performance of Full-Depth Precast, Prestressed Concrete Overhang, Bridge Deck Panels

The performance of a new full-depth precast overhang panel system for concrete bridge decks is investigated experimentally. In contrast to conventional cast-in-place deck overhangs, the proposed full-depth precast overhang system has the potential to speed up construction, reduce costs, and improve safety. Load-deformation behavior up to factored design load limits is first investigated. The panel is then loaded near its edge to examine the collapse capacity and the associated failure modes—particularly the influence of panel-to-panel connections that exist, transverse to the bridge deck axis. Comparative tests are also conducted with a conventional cast-in-place overhang system. When compared to the conventional cast-in-place overhang behavior, the experimental results show that the precast full-depth overhang introduces different behavior modes, largely due to the influence of the partial depth panel-to-panel connection, which reduces the capacity by some 13%.     

Composite Action and Adhesive Bond between Fiber-Reinforced Polymer Bridge Decks and Main Girders

This paper describes the behavior of hybrid girders consisting of fiber-reinforced polymer (FRP) bridge decks adhesively connected to steel main girders. Two large-scale girders were experimentally investigated at the serviceability and ultimate limit state as well as at failure. One of the girders was additionally fatigue loaded to 10 million cycles. Compared to the behavior of a reference steel girder, deflections of the two girders at the SLS were decreased by 30% and failure loads increased by 56% due to full composite action in the adhesive layer. A ductile failure mode occurred: Deck compression failure during yielding of the steel girder. The adhesive connections were able to prevent buckling of the yielding top steel flanges. Thus, compared to the reference steel girder, the maximum deflections at failure could be increased up to 130%. No deterioration due to fatigue loading was observed. Based on the experimental results, a conceptual design method for bonded FRP/steel girders was developed. The proposed method is based on the well-established design method for hybrid girders with concrete decks and shear stud connections. The necessary modifications are proposed.     

Structural Characterization of Hybrid Fiber-Reinforced Polymer-Glulam Panels for Bridge Decks

The structural characterization of hybrid fiber-reinforced polymer (FRP)–glued laminated (glulam) panels for bridge deck construction is examined using a combined analytical and experimental approach. The structural system is based on the concept of sandwich construction with strong and stiff FRP composite skins bonded to an inner glulam panel. The FRP composite material was made of E-glass reinforcing fabrics embedded in a vinyl ester resin matrix. The glulam panels were fabricated with bonded eastern hemlock vertical laminations. The FRP reinforcement was applied on the top and bottom faces of the glulam panel by wet layup and compacted using vacuum bagging. An experimental protocol based on a two-span continuous bending test configuration is proposed to characterize the stiffness, ductility, and strength response of FRP-glulam panels under simulated loads. Half-scale FRP-glulam panel prototypes with two different fiber orientations, unidirectional (0°) and angle-ply (±45°), were studied and the structural response correlated with control glulam panels. A simple beam linear model based on laminate analysis and first-order shear deformation theory was proposed to compute stiffness properties and to predict service load deflections. In addition, a beam nonlinear model based on layered moment-curvature numerical analysis was proposed to predict ultimate load and deflections. Correlations between experimental results and the two proposed beam models emphasize the need for complementing both analytical tools to characterize the hybrid panel structural response with a view toward bridge deck design.     

Influence of Reinforcement on the Behavior of Concrete Bridge Deck Slabs Reinforced with FRP Bars

This paper presents the results of an experimental study to investigate the role of each layer of reinforcement on the behavior of concrete bridge deck slabs reinforced with fiber-reinforced polymer (FRP) bars. Four full-scale concrete deck slabs of 3,000?mm length by 2,500?mm width and 200?mm depth were constructed and tested in the laboratory. One deck slab was reinforced with top and bottom mats of glass FRP bars. Two deck slabs had only a bottom reinforcement mat with different reinforcement ratios in the longitudinal direction, while the remaining deck slab was constructed with plain concrete without any reinforcement. The deck slabs were supported on two steel girders spaced at 2,000?mm center to center and were tested to failure under a central concentrated load. The three reinforced concrete slabs had very similar behavior and failed in punching shear mode at relatively high load levels, whereas the unreinforced slab behaved differently and failed at a very low load level. The experimental punching capacities of the reinforced slabs were compared to the theoretical predictions provided by ACI 318-05, ACI 440.1R-06, and a model proposed by the writers. The tests on the four deck slabs showed that the bottom transverse reinforcement layer has the major influence on the behavior and capacity of the tested slabs. In addition, the ACI 318-05 design method slightly overestimated the punching shear strength of the tested slabs. The ACI 440.1R-06 design method yielded very conservative predictions whereas the proposed method provided reasonable yet conservative predictions.     

Field Performance of the Fiber-Reinforced Polymer Deck of a Truss Bridge

The MD 24 Bridge over Deer Creek in Harford County, Md., was one of the projects chosen by the Federal Highway Administration’s Innovative Bridge Research and Construction Program for bridge deck replacement by fiber-reinforced polymer (FRP) composites. A thorough discussion is presented on Maryland State Highway Administration’s first bridge rehabilitation project utilizing a FRP deck. The discussion includes design details, installation procedure, construction methods and in situ load testing with a wireless monitoring system. The research team installed a monitoring system to record the effects of live loads on the bridge system, including truss members, steel stringers, and plate action of the FRP deck. Finite-element models were also used in this phase. Dynamic effects of the FRP system, composite action between steel stringers and the FRP deck as well as the effective width and distribution factors of stringers were obtained and compared with the AASHTO specifications. Recommendations are also offered on improving the design details based on this experience.     

Fatigue Behavior of a Steel-Free FRP–Concrete Modular Bridge Deck System

This paper presents results of an evaluation of the fatigue performance of a novel steel-free fiber-reinforced polymer (FRP)–concrete modular bridge deck system consisting of wet layup FRP–concrete deck panels which serve as both formwork and flexural reinforcement for the steel-free concrete slab cast on top. A two-span continuous deck specimen was subjected to a total of 2.36 million cycles of load simulating an AASHTO HS20 design truck with impact at low and high magnitudes. Quasistatic load tests were conducted both before initiation of fatigue cycling and after predetermined numbers of cycles to evaluate the system response. No significant stiffness degradation was observed during the first 2 million cycles of fatigue service load. A level of degradation was observed during subsequent testing at higher magnitudes of fatigue load. A fairly elastic and stable response was obtained from the system under fatigue service load with little residual displacement. The system satisfied both strength and serviceability limit states with respect to the code requirements for crack width and deflection.     

Connection of Concrete Railing Post and Bridge Deck with Internal FRP Reinforcement

The use of fiber-reinforced polymer (FRP) reinforcement is a practical alternative to conventional steel bars in concrete bridge decks, safety appurtenances, and connections thereof, as it eliminates corrosion of the steel reinforcement. Due to their tailorability and light weight, FRP materials also lend themselves to the development of prefabricated systems that improve constructability and speed of installation. These advantages have been demonstrated in the construction of an off-system bridge, where prefabricated cages of glass FRP bars were used for the open-post railings. This paper presents the results of full-scale static tests on two candidate post–deck connections to assess compliance with strength criteria at the component (connection) level, as mandated by the AASHTO Standard Specifications, which were used to design the bridge. Strength and stiffness until failure are shown to be accurately predictable. Structural adequacy was then studied at the system (post-and-beam) level by numerically modeling the nonlinear response of the railing under equivalent static transverse load, pursuant to well-established structural analysis principles of FRP RC, and consistent with the AASHTO LRFD Bridge Design Specifications. As moment redistribution cannot be accounted for in the analysis and design of indeterminate FRP RC structures, a methodology that imposes equilibrium and compatibility conditions was implemented in lieu of yield line analysis. Transverse strength and failure modes are determined and discussed on the basis of specification mandated requirements.     

Sustained-Load and Fatigue Performance of a Hybrid FRP-Concrete Bridge Deck System

The design and construction of bridge systems with long-term durability and low maintenance requirements is a significant challenge for bridge engineers. One possible solution to this challenge could be through the use of new materials, e.g., fiber-reinforced polymer (FRP) composites, with traditional materials that are arranged as an innovative hybrid structural system where the FRP serves as a load-carrying constituent and a protective cover for the concrete. This paper presents the results of an experimental investigation designed to evaluate the performance of a 3/4 scale hybrid FRP-concrete (HFRPC) bridge deck and composite connection under sustained and repeated (fatigue) loading. In addition, following the sustained-load and fatigue portions of the experimental study, destructive testing was performed to determine the first strength-based limit state of the hybrid deck. Results from the sustained-load and fatigue testing suggest that the HFRPC deck system might be a viable alternative to traditional cast-in-place reinforced concrete decks showing no global creep behavior and no degradation in stiffness or composite action between the deck and steel girders after 2 million cycles of dynamic loading with a peak load of 1.26 times the scaled tandem load (TL). Furthermore, the ultimate strength test showed that the deck failed prior to the global superstructure at a load approximately six times the scaled TL.     

Conformable Tire Patch Loading for FRP Composite Bridge Deck

Fiber-reinforced polymer (FRP) composites are increasingly being used in bridge deck applications. However, there are currently only fledgling standards to design and characterize FRP deck systems. One area that should be addressed is the loading method for the FRP deck. It has been observed that the type of loading patch greatly influences the failure mode of a cellular FRP deck. The contact pressure distribution of a real truck loading is nonuniform with more concentration near the center of the contact area as a result of the conformable contact mechanics. Conversely, the conventional rectangular steel patch on a FRP deck act like a rigid flat punch and produces stress concentration near the edges. A proposed simulated tire patch has been examined for loading a cellular FRP deck with the load distribution characterized by a pressure sensitive film sensor and three-dimensional contact analysis using ANSYS. A loading profile is proposed as a design tool for analyzing FRP deck systems for strength and durability. Local top surface strains and displacements of the cellular FRP deck are found to be higher with proposed loading profile compared to those for the conventional uniformly distributed loading. Parametric studies on the deck geometry show that the global displacement criterion used for characterizing bridge deck is inadequate for a cellular FRP deck and that the local effects must be considered.     

FEA of Complex Bridge System with FRP Composite Deck

Innovative fiber-reinforced polymer (FRP) composite highway bridge deck systems are gradually gaining acceptance in replacing damaged/deteriorated concrete and timber decks. FRP bridge decks can be designed to meet the American Association of State Highway and Transportation Officials (AASHTO) HS-25 load requirements. Because a rather complex sub- and superstructure system is used to support the FRP deck, it is important to include the entire system in analyzing the deck behavior and performance. In this paper, we will present a finite-element analysis (FEA) that is able to consider the structural complexity of the entire bridge system and the material complexity of an FRP sandwich deck. The FEA is constructed using a two-step analysis approach. The first step is to analyze the global behavior of the entire bridge under the AASHTO HS-25 loading. The next step is to analyze the local behavior of the FRP deck with appropriate load and boundary conditions determined from the first step. For the latter, a layered FEA module is proposed to compute the internal stresses and deformations of the FRP sandwich deck. This approach produces predictions that are in good agreement with experimental measurements.     

Designing and Testing of Concrete Bridge Decks Reinforced with Glass FRP Bars

In addition to their high strength and light weight, fiber-reinforced polymer (FRP) composite reinforcing bars offer corrosion resistance, making them a promising alternative to traditional steel reinforcing bars in concrete bridge decks. FRP reinforcement has been used in several bridge decks recently constructed in North America. The Morristown Bridge, which is located in Vermont, United States, is a single span steel girder bridge with integral abutments spanning 43.90 m. The deck is a 230 mm thick concrete continuous slab over girders spaced at 2.36 m. The entire concrete deck slab was reinforced with glass FRP (GFRP) bars in two identical layers at the top and the bottom. The bridge is well instrumented at critical locations for internal temperature and strain data collection with fiber-optic sensors. The bridge was tested for service performance using standard truck loads. The construction procedure and field test results under actual service conditions revealed that GFRP rebar provides very good and promising performance.     

Testing, Analysis, and Evaluation of a GFRP Deck on Steel Girders

North Carolina has recently installed a fiber-reinforced polymer (FRP) deck on steel girders at a site in Union County. The bridge was instrumented with foil strain gauges, strain transducers, and displacement transducers. The bridge was then tested with a simulated MS-22.5 design load. Experimental data confirmed full composite interaction between the girders and the FRP deck panels. The neutral axis was measured to be 383?mm above the bottom flange of the 618-mm-deep girder. It was found that composite action could be estimated within 3% using a transformed section analysis of the deck panels. For two lanes loaded, the maximum live load distribution factor was computed to be 0.75. When looking at the overall performance of the structure, the deck deflected 5?mm, with the allowable stress at least 10 times over the maximum stress measured in the material. The girder deflection of 7?mm was well within the parameters set forth by AASHTO. Simple span deflection equations were found to conservatively model the anticipated deflection of the girders when using the transformed section properties.     

Structural Behavior of FRP Composite Bridge Deck Panels

Fiber-reinforced polymer (FRP) composite bridge deck panels are high-strength, corrosion resistant, weather resistant, etc., making them attractive for use in new construction or retrofit of existing bridges. This study evaluated the force-deformation responses of FRP composite bridge deck panels under AASHTO MS 22.5 (HS25) truck wheel load and up to failure. Tests were conducted on 16 FRP composite deck panels and four reinforced concrete conventional deck panels. The test results of FRP composite deck panels were compared with the flexural, shear, and deflection performance criteria per Ohio Department of Transportation specifications, and with the test results of reinforced concrete deck panels. The flexural and shear rigidities of FRP composite deck panels were calculated. The response of all panels under service load, factored load, cyclic loading, and the mode of failure were reported. The tested bridge deck panels satisfied the performance criteria. The safety factor against failure varies from 3 to 8.