NaOCl degradation of one-step one-bottle self-etch adhesives bonded to bovine dentine

Objective: The aim of the present study was to assess the influence of an in vitro aging regime (NaOCl storage) on dentine microtensile bond strength (μTBS) of five one-step one-bottle self-etch adhesives in comparison with bond strength of two-step self-etch adhesive.

Material and methods: Flattened dentine surfaces from 30 bovine incisors were bonded with five one-step one-bottle self-etch adhesives (iBond, Clearfil S3 Bond, AdheSE One F, G-Bond, Optibond all-in-one) and one two-step self-etching adhesive (Clearfil SE Bond). Composite buildups were done with microhybrid resin composite. Bonded samples were sectioned into resin–dentine sticks of 0.8 mm² cross section. Randomly selected 20 sticks were tested directly by microtensile bond strength testing machine, whereas another randomly selected 20 sticks were tested after being stored in solution of 10% NaOCl for 5 h. Data were analyzed by two-way analysis of variance (ANOVA) and Tukey’s honest significant difference (HSD) tests (p < 0.05).

Results: All adhesives exhibited similar dentine bond strength with exception of G-Bond. After NaOCl storage, μTBS reduced in all groups significantly. The lowest μTBS were found for G-Bond. Rest of one-step self-etch adhesives presented similar μTBS with two-step self-etch adhesive.

Conclusion: Interfaces of resin–dentine bonding are susceptible to NaOCl degradation. The amount of the destruction depends on adhesive system. NaOCl degradation of the nonresin encapsulated collagen fibers might decrease long-term stability of resin bonding with dentine.     

Effect of adhesive type and composite viscosity on the dentin bond strength

Objectives: Evaluate the influence of composite resins viscosity and type of cure of the adhesive systems on the bond strength of composite resins submitted to artificial aging.

Methods: Dentin specimens (n = 240) were divided into 2 groups: Group GC: GrandioSO, and Group GF: GrandioSO Heavy Flow. These groups were subdivided into 6: FM: Futurabond M – light cured, FDCC: Futurabond Dual Cure – chemical cured, FDCL: Futurabond Dual Cure – light cured, CS3: Clearfil S3 – light cured, CDCC: Clearfil Dual Cure – chemical cured, and CDCL: Clearfil Dual Cure – light cured. Resin blocks were build up on the dentin surface. Half of samples on each group were cut to obtain resin/dentin sticks (1 × 1 mm). The other half was first submitted to thermomechanical aging. The dentin/resin sticks were submitted to microtensile bond strength test and the results were analyzed using three-way ANOVA and Tukey’s test (α = 5%).

Results: ANOVA showed significant influence for adhesive (p = 0.0000) and aging (p = 0.0001). No significant influence of the composite viscosity on bond strength was observed (ANOVA: p = 0.0861). For adhesive, the results of Tukey’s test (MPa) were CDCC: 13.44 (±5.13)a; FM: 14,01 (±2.71)a; CDCL: 14.51 (±4.98)a; FDCC: 18.66 (±7.13)b; CS3: 18.80 (±6.50)b; FDCL: 19.18 (±7.39)b. For aging: AGED: 14.99 (±6.32)a; NOT AGED: 17.87 (±5.97)b.

Conclusion: Composite resin viscosities did not influence on the bond strength. Type of cure of the adhesives had influence on the bond strength. Thermomechanical aging decreased the bond strength.     

Effects of mixing techniques and dentin moisture conditions on push-out bond strength of ProRoot MTA and Biodentine

Objective: To evaluate the influence of manual and mechanical mixing techniques as well as the effects of moisture on the push-out bond strength of ProRoot MTA (Dentsply Tulsa Dental, Tulsa, OK, USA) and Biodentine (Septodont, Saint Maur des Fosses, France) to radicular dentin.

Material and methods: Two hundred and forty dentin discs were assigned into three groups with respect to the moisture condition tested: (1) dry, (2) paper points, (3) wet. The discs were further divided into four subgroups according to the calcium silicate cements (CSCs) and mixing techniques used: (1) ProRoot MTA mixed manually, (2) ProRoot MTA mixed mechanically, (3) Biodentine mixed manually, and (4) Biodentine mixed mechanically. Bond strengths of the cements to root canal dentin were measured using a push-out test setup. The data were statistically analyzed using three-way ANOVA and Bonferroni post hoc test p = 0.05.

Results: The data indicated that the push-out bond strength values were significantly affected by CSCs, mixing techniques, and moisture conditions (p < 0.001). Dry conditions caused a significant decrease in bond strength values for both CSCs (p < 0.001). The mean bond strength of Biodentine was significantly higher than that of ProRoot MTA, regardless of the mixing techniques and moisture conditions (p < 0.001). Mechanical mixing favored bond strength values statistically compared to manual mixing (p < .001).

Conclusion: The mixing techniques and moisture conditions have an effect on the push-out bond strengths of ProRoot MTA and Biodentine. Dry samples and manual mixing of cements deteriorate the push-out bond strengths values.     

Do phosphoric acid esters affect the immediate enamel bond strengths?

Purpose: To investigate the effects of phosphoric acid esters (PAEs)-containing primers on the micro-tensile bond strengths (MTBS) of etched enamel, the micro-morphologies of the resin–enamel interfaces, and the enamel surfaces.

Materials and Methods: Thirty-three bovine incisors were used in this study. After the labial enamel surfaces were highly polished, they were etched, water sprayed, and air-dried. Afterward, the enamel surfaces were treated with or without (control) one of three PAEs-containing primers (40%MDP, Ivoclar Vivadent; Resulcin AquaPrime A + B, DMG; Xeno V, Dentsply), water sprayed, and air-dried. Subsequently, an adhesive Heliobond (Ivoclar Vivadent) was applied and resin composite (Core Build-up, Bisco) was placed incrementally. They were prepared into multiple beams of about 1 × 1 × 8 mm for MTBS tests. The enamel surfaces and resin–enamel interfaces were analyzed by SEM and TEM. The data were analyzed by two-way ANOVA and LSD test.

Results: Using PAEs-containing primers could increase the enamel MTBS (p < 0.05). The primer MDP produced higher MTBS than the primer Resulcin AquaPrime A + B and Xeno V. The SEM findings revealed the primed enamel surfaces were covered with a thin or glue-like layer of monomer-calcium salts of PAEs and the residual enamel crystallites, and various micro-porosities were detected within the hybrid layers. The TEM findings revealed the hydroxyapatite crystallites were tightly covered by the adhesive, the adhesive mixed with resin composite, or sparse irregular enamel crystallites.

Conclusion: The application of PAEs-containing primers on the etched enamel substrate could significantly increase the immediate enamel bond strengths. However, this effect was dependent on the individual PAEs-containing primer used.     

Evaluation of the shear bond strength of two resin cements on different CAD/CAM materials

Objective: This study investigated the bond strength of two resin cements (Panavia F 2.0 and Multilink N) to different CAD/CAM materials: resin nanoceramic (RNC; Lava Ultimate), hybrid ceramic (HC; Vita Enamic), zirconia-reinforced lithium silicate ceramic (ZLDC; Vita Suprinity), and lithium disilicate glass-ceramic (LDG; IPS e.max CAD HT).

Material and methods: CAD/CAM blocks of 2-mm thickness were sectioned with a slow-speed diamond-saw sectioning machine. The slabs were then embedded in autopolymerizing acrylic resin (n = 12), and resin cements were applied to the surface of the specimens. All specimens were stored in water for 24 h and subjected to 5000 thermal cycles. Bond strength was measured by means of the shear bond strength test. The data were statistically analyzed by two-way ANOVA and Tukey LSD post hoc tests.

Results: The results of the two-way ANOVA test indicated that the bond strength values varied significantly depending on the CAD/CAM restorative materials, resin cements, and interaction of these variables (p < 0.05). The RNC group showed the highest bond strength for Panavia F 2.0 (p < 0.05); there were no significant differences among other CAD/CAM materials for Panavia F 2.0 (p > 0.05). The LDG group showed the highest bond strength for Multilink N, it was followed by the ZLDC group (p < 0.05); there were no significant differences between RNC and HC groups (p > 0.05).

Conclusions: Choosing resin cements for restorations should be done carefully because bond strength values vary significantly depending on the resin cement and CAD/CAM restorative material.     

Residual monomer release from orthodontic adhesives cured with different light sources

Introduction: The aim of this study was to evaluate the residual monomer release from orthodontic adhesives cured with light-emitting diode (LED) and halogen light sources.

Methods: Seven hundred and twenty stainless steel brackets were divided into 3 groups according to the adhesive system used (Transbond XT light-cure adhesive [TXT], Transbond LR capsule [LR], and Light Bond light-cure adhesive paste [LB]), and each group was divided into 2 subgroups according to light-curing procedure (LED or halogen). Brackets were bonded with adhesives onto tooth buccal surfaces and polymerized. Each specimen contained 24 brackets that simulated the oral environment (n = 5). The specimens were immersed in a 75% ethanol/water solution at 37 °C for 10 min, 1 h, 1 d, 7 d, 14 d, and 30 d, respectively. Eluted monomers (Bis-GMA, UDMA, and TEGDMA) were detected using HPLC.

Results: There was residual monomer release at all time periods, and the highest amount of release was observed cumulatively on the 30th day. The cumulative Bis-GMA released from adhesives was not different (p > 0.05). The cumulative TEGDMA released from adhesives was statistically different (p < 0.05). There was no statistical difference between QTH and LED light-curing units for each adhesive (p > 0.05).

Conclusions: The release of residual monomers stays at a high level for a long time after polymerization. The total leaching of residual monomers from the Light Bond light-cure sealant resin plus Light Bond light-cure adhesive paste was higher than that of other materials for both curing units. Different curing units (LED or QTH) did not affect the monomer release from the orthodontic adhesives.     

Shear bond strength of PEEK and PEEK-30GF cemented to zirconia or titanium substrates

Objectives: The aim of this study was to evaluate the use of dual-cure resin cement to promote the bonding between a veneering PEEK and zirconia or titanium surfaces.

Materials and methods: The surface of titanium and sintered zirconia disks were gritblasted, ultra-sonically cleaned in distilled water, and dryed by oil-free air. Then, a adhesive system was applied on the clean and dry surfaces. Disks of PEEK or 30% glass-reinforced PEEK were cut from a rod and their surface were acid etched and therefore the PEEK roughness was analysed using a contact profilometer. A resin cement was then applied between the substrates and the veneering PEEK and light cured for 4 Shear bond strength tests were performed on PEEK-cement to zirconia or titanium interfaces. Scanning electron microscopy (SEM) analyses were performed to evaluate the samples surface, interface and failure mode.

Results: Surface treatment with acid etching decreased the average roughness of PEEK-based surfaces. oMicroscopic analyses by SEM revealed morphological aspects of a poor bonding between the resin-based cement and PEEK. Those aspects could be confirmed by the low mean values in shear bond strength. The fracture analysis showed that the main failure mode was adhesive, which explain the low values of shear bond strength.

Conclusion: PEEK is a promising material for dental applications. However, significant improvements on surface modifications and in chemical composition of the cement are still required for dental applications involving cementation of PEEK or PEEK-30GF to zirconia or titanium concerning a desirable long-term clinical performance of prosthetic structures.     

Modeling of nonstationary processes during separation of multicomponent isotope mixtures

The article presents a mathematical model for calculation of nonstationary hydraulic and separation processes in a gas centrifuge (GC) cascade for separation of multicomponent isotope mixtures. The model has been applied to calculate the parameters of nonstationary processes in a GC cascade for separation of krypton, germanium and tungsten isotopes. As a result, the specifics of the excess holdup distribution along the cascade stages has been identified, and variations of the isotope concentrations in a nonstationary process have been revealed. The data obtained show that the proposed mathematical model is able to adequately describe nonstationary hydraulic processes in GC cascades for separation of multicomponent isotope mixtures.

Highlights:

Mathematical model of cascade for separation of multicomponent isotope mixture has been developed.

The model verification has been done.

The isotope transient regularities into cascade during nonstationary processes has been identified.     

Effect of desensitizers on the microleakage of previously restored Class V resin composite restorations

Objectives: The aim of this in vitro study was to evaluate the effect of different desensitizers’ application on the microleakage of previously restored Class V composite resin restorations.

Materials and methods: Class V cavities were prepared on the buccal surfaces of 40 extracted human third molars. Forty box-shaped cavities were divided into four groups, based on the desensitizers used (n = 10). All teeth were restored with the same bonding agent and composite material. No desensitizer was applied in the control group. In the experimental groups, BisBlock, Gluma and Universal bonding agents were the desensitizers. The desensitizers were applied after completion of composite restorations according to manufacturers’ instructions. All specimens were then thermocycled at 5–55 °C, with a 10-s dwell time for 500 cycles. The samples were then immersed in 0.5% methylene blue dye for 24 h, sectioned into two equal halves, evaluated for microleakage using a stereomicroscope at 30× magnification and scored on a scale of 0–3. The data were analysed using the Kruskal–Wallis test at the significance level p < 0.05.

Results: There were no significant differences in microleakage after desensitizer application (p > 0.05). However, based on the obtained numerical values in our study, while the BisBlock and bonding groups showed lower microleakage at the occlusal margin, BisBlock, Gluma and bonding group showed lower microleakage at the gingival margin compared to the control group.

Conclusions: The application of desensitizers as a post-treatment option could be considered an advisable procedure to minimize microleakage.     

Hydroxyl Radical Oxidation Processes For The Removal Of Triazine From Natural Water

The purpose of this study was to point out processes that can provide triazine oxidation via hydroxyl radical production in a water treatment line. We focus our attention on:

- oxido-flocculation, using Fe²⁺, H₂O₂

- inter-oxidation, using O₃, H₂O₂ and eventually an heterogeneous catalyst.

- disinfection, using UV, O₃ and H₂O₂ combinations.

Results show that triazines can be removed by all these processes with different efficiencies. At full scale, the O₃/H₂O₂ process presents the best performances from an economical and technical point of view.     

Experimental and numerical characterization of shape memory polymer and metal laminates

The interface strength of a Shape Memory Polymer – Stainless Steel (SMP-SS) laminate system has been studied under a wide range of test conditions. The adhesive strength of the laminates has been explored using the peel test at room temperature as well as the glass transition temperature of the SMP. The analysis was also repeated at varying speeds and SMP thickness in order to quantify the effect of strain rate and adherend thickness on the bond strength of the laminate.

The experimental tests have been validated using finite element analysis of the SMP – SS laminate system. The finite element study further explores the role of polymer stresses and strains in the polymer film and adhesive layer in inducing delamination and wrinkling.

Significant decrease in strains in the adherend are observed on increasing its thickness. The adhesive strength of the laminate system is found to decrease at higher temperatures. Also the adherend is observed to wrinkle at longitudiunal strains nearing 35%.     

Recent Advances in Flame Retardancy of Polymeric Materials (Materials,Applications, Industry Developments,Markets)

The Fifth Annual Conference on Flame Retardancy was held May 24–26, 1994, at the Ramada Plaza Hotel, Stamford, Connecticut, USA. The conference was organized by Business Communications Company, Inc., Norwalk, Connecticut (Company President, Mr. Louis Naturman; Conference Coordinator, Mrs. Sharon D. Faust). New materials (polymers, blends, composites), their applications, industry developments, and markets were considered. Specifically, the most important topics were:

Introduction of new technological achievements and development in the field of flame retardancy (FR)

Review of the current state of science and technology in FR

Review of applications and markets for FR products

Presentation of recent developments in local and global standardization and in testing technology

Discussion of toxicity and environmental issues

Provision of a unique opportunity for newcomers to FR research technology and marketing to become acquainted with the FR field in all its aspects

Discussion of halogen-based and non-halogen-based flame retardant chemicals, syngergism, intumescence, FR mechanisms, modeling, flame parameters, inherently FR polymers, and polymer blends     

Dihydrogen Catalysis: A Remarkable Avenue in the Reactivity of Molecular Hydrogen

Molecular hydrogen is the simplest and most abundant compound in the universe and is involved in numerous industrial chemical processes. In conventional chemistry, dihydrogen typically plays the role of a reductant and a reagent for homogeneous and heterogeneous hydrogenation processes such as the industrial and enzymatic ammonia formation, reduction of metallic ores and hydrogenation of unsaturated fats and oils. However, there are also processes in which molecular hydrogen participates as promoter, and even as catalyst. The catalytic role of the dihydrogen in free-valence migration in irradiated polymers and the interstellar isomerization of the formyl cation (protonated carbon monoxide) are well-documented examples of such processes. Recently, this issue has received new attention. Dihydrogen has been shown to play the role of a dehydrogenation catalyst (involving particularly metallocomplexes and inorganic materials), a relay (pass-on) transfer molecular agent and a transporter of protons.

This review article, combined with original results, is focused on the mechanisms of the chemical processes where dihydrogen demonstrates catalytic behavior. We will call these processes (with somewhat broader meaning of the term) “dihydrogen catalysis” (DHC) which also includes the reactions mediated by transition metal dihydrides. Dihydrides are tentatively considered as pre-activated dihydrogen, coordinated to a metal center or implanted into a solid surface/support.

DHC reactions are classified into five major reaction types: (i) dihydrogen-assisted relay transport of H-atoms (H2-RT); (ii) dihydrogen-assisted stepwise relay transport of H-atoms or of a free valence (sH2-RT); (iii) dihydrogen-assisted proton transport (H2-PT); (iv) dihydrogen-assisted dehydrogenation (H2-DeH); and (v) pre-activated dehydrogenation (PA-DeH). The classification of these mechanisms is based on a detailed analysis of numerous potential energy surfaces studied by DFT and ab initio methods in conjunction with available experimental data. The H2-RT, H2-DeH, and PA-DeH processes occur via cyclic transition states. The relay H2-RT transport involves the H-H-H triad linked to both H-donor and H-acceptor centers, whereas the transition state ring in the H2-DeH dehydrogenation processes involves a H-H-H-H tetrad with the dihydrogen catalyst located in the middle. The H2-PT mechanism provides the transport of a proton mediated by dihydrogen combined in a triangular (H₃⁺)-carrier unit.

There are also practically important processes stimulated by dihydrogen such as the hydrogen spillover and hydrogen build-up in electronics, in which the catalytic role of dihydrogen is ambiguous, either because of the uncertainties in mechanisms, or prevailing traditional views. Some examples are briefly discussed in the framework of the concept of dihydrogen catalysis, some being provided with theoretical support (in part calculated by us), and others being merely hypothesized to provide suggestions to an interested reader.     

MEASUREMENT OF INTERFACIAL AREA AND MASS TRANSFER COEFFICIENTS BY CHEMICAL METHOD OF C02 ABSORPTION INTO AQUEOUS SOLUTIONS OF NaOH IN A MODEL COLUMN WITH EXPANDED METAL SHEET PACKING

The theory of gas absorption accompanied by fast pseudo-fast order reaction which considered dependences of diffusivity, kinetic constant and Henry's law constant on absolute temperature and ionic strength was used to obtain values of effective interfacial areas and mass transfer coefficients in gas and liquid phase.

Experimental measurement of carbon dioxide absorption from mixture with air was performed in a pilot-plant column with expanded metal sheet packing irrigated with sodium hydroxide solution.

Resulting liquid and gas-side mass transfer coefficients are compared with values obtained from physical Absorption measurement of carbon dioxide into water and with measurement of gas-side mass transfer coefficient for sulphur dioxide in the same column.

The differences between determined values are discussed.     

Comparative study: Correlating extraction efficiency for Hg(II), Cd(II), and Pb(II) metal ions with the chelate stability and total hardness in simple nitrogen donors

Four N-donors (PHDA, ATPH, APHO, and MTAN) containing NH₂ were used to extract Hg(II), Cd(II), and Pb(II). Their extraction capacity was determined by measurement of percentage extraction.

The chelates extract these metals differently: for example, efficiency of ATPH was the highest for Hg(II) compared to PHDA, APHO, and MTAN.

The extraction efficiency was found to depend on: donor atom hardness, chelate total hardness, metal: chelate mole ratio and substituent’s electronic effects. Among all, total hardness and chelate stability are key factors and molecule of small (E_HOMO – E_LUMO) is more reactive, where extraction efficiency increases as molecular stability decreases.     

The Photochemical Generation of Ozone : Present State–of–the–Art

This paper reflects an investigation of the feasibility of photochemical generation of ozone by irradiating gases containing oxygen with Hg lamps of the highest performance emitting the 185 nm line. Besides the expected photostationary equilibrium, determining factors for practical yields in ozone generation by the 185 nm wavelength are : the reactor and gas temperature, the reactor geometry, and the gas composition, as well as the pressure.

Further developments are expected in the field of lamp construction and also improvement of reactor geometry. A better knowledge of the aging of the lamps is required, as well as of the photochemical reactions of oxygen in the technologies applied.

Systems presently available are most promising for application on small scale or in areas of public water distribution which have no developed structure.

     

Effect of monolithic zirconia on the degree of conversion of two resin cements analyzed by FT-IR/ATR spectroscopy

Objective: This study aimed to evaluate the degree of conversion (DC) of two different resin cements polymerized under the monolithic zirconia specimens in different thicknesses and colors.

Material and methods: Partially stabilized monolithic zirconia blocks (inCoris TZI) were cut into three different thicknesses (0.5, 1.0, and 2.0 mm) and the specimens were divided into four color groups (A1, A2, A3, and A4). The light transmittance of each specimen was measured. Panavia F 2.0 or Variolink N resin cement was applied into teflon mold and irradiated using the light emitting diode curing unit for 20 s under monolithic zirconia specimen (n = 10). The resin cement specimens were stored at room temperature under dry conditions. The DC of each specimen was measured by Fourier transform infrared-attenuated total reflection (FT-IR/ATR) spectroscopy after the 1st and 10th day. Data were analyzed with two-way analysis of variance (ANOVA), two-way repeated measures ANOVA, three-way repeated measures ANOVA, and the Tukey least significant difference (LSD) tests (α = 0.05).

Results: The light-cure resin cement groups showed higher DC than the dual-cure resin cement groups (p < 0.05). The DC of both resin cements reduced with an increase in the thickness and darkening of the color of monolithic zirconia specimens. There was a statistically meaningful increase in the 10th-day values for dual-cure resin cement (p < 0.05), whereas there were no significant differences between the 1st- and 10th-day values for light-cure resin cement (p > 0.05).

Conclusion: The use of light-cure resin cement can be suggested for the luting of monolithic zirconia restorations.     

First Year Operation Report of the Corona Discharge Ozone Swimming Pool Water Treatment Systems at the Peck Aquatic Facility,Milwaukee, Wisconsin

The two corona discharge ozone swimming pool water treatment systems installed in the Peck Aquatic Center in Milwaukee, WI now have been in continuous operation since September, 1987. The two pools are part of the Karl Jewish Campus Facility of the Harold and Judy Sampson Campus of the Milwaukee Jewish Community Center.

The operation of these water treatment systems has shown that safe and high quality pool water is obtained reliably and economically. One pool (Main Pool) is of Olympic size, the other (Learner pool) is designed especially for use by children. Both pools utilize a full corona discharge ozone water treatment system. They were the first ozone systems in the U.S. to be built for public pools using the process of ozonation, flocculation, filtration, ozone removal and residual chlorination.

An extensive testing program was initiated in cooperation with the Wisconsin Department of Health. The bacteriological water quality from these swimming pools was in compliance with Wisconsin State Health Regulations and the German DIN Standard 19,643.

The first year of operation of the Peck Aquatic Center has shown that the corona discharge ozone pool water treatment process can:

1) Operate reliably in a public swimming pool environment without the need for highly or special operator qualifications.

2) Produce continuously bacteria- and virus-free pool water without the harmful and unpleasant effects of chlorine.

3) Creates a user constituency group praising and promoting the use of “minimal chlorine swimming” in the community.     

New Pilot Plant Studies at the Budapest Waterworks

The quality of water provided by the Budapest Waterworks should comply with the standards prescribed by the European Community. According to these provisions, on one of the major water-producing regions (Csepel Island), rows of wells of 60,000 m³/day yield have been closed recently, and in the immediate future further plants would have been closed because of the high iron and manganese content of the water.

The raw water obtained from 100 different wells will be purified by a water treatment plant of 150,000 m³/day capacity. Considering the high iron content (0.05–0.15 mg/L) and manganese content (0.05–0.2 mg/L), the raw water fails to comply with the requirements of the potable water standard.

Since 1990, over a period of three years, we conducted water purification experiments in several stages. In these, three methods of oxidizing as well as single and double layer open rapid filters were applied to oxidize the manganese (and, to a lesser extent, the water) present in dissolved form, resp., to destroy various living organisms.

In the course of the experiments, it became clear that the chlorine and chlorine + air methods are efficient in case of a small quantity of iron to be oxidized and only 20–25% of the dissolved manganese content could be oxidized.

Neither of the two methods could ensure firm management of microbiological and bacteriological characteristics. The best results were obtained by ozone oxidation, in which case the chemical oxidizing process was almost fully completed and even the chlorine-resistant living organisms could be destroyed.

On the basis of the experiments carried out, the investment program of the water treatment plant was worked out and the conditions of an international tender were compiled whose winner will be commissioned to build up the water works in the time period 1993–1996. One of the main steps of the proposed technology is the ozone treatment.     

HEAT TRANSFER IN TRICKLE-BED REACTORS

The mechanism of radial heat transfer in two-phase flow through packed beds is examined. A model with 2 parameters: an effective radial thermal conductivity in the bed, k_e , and a heat transfer coefficient, h_w , at the wall, give a satisfactory interpretation of the radial temperature profile.

k_e was expressed in terms of a stagnant contribution, due to the heat conduction through the solid and the fluid in the void space, and a radial mixing contribution of the gas and liquid phases, due to the radial component of the velocity of both fluids. The radial mixing contribution of the liquid ( k_e ) _L was compared with radial mass dispersion data, and a satisfactory agreement was obtained.

Moreover, ( k_e )was much higher than the gas mixing and the stagnant contributions.

Correlations for hw and k_e ) _L have been proposed in accordance with the hydrodynamic regimes of the two-phase flow.