MANAGING MOIST PADDY BY DRYING,TEMPERING AND AMBIENT AIR VENTILATION

ABSTRACT

This paper describes a strategy for reducing moisture in paddy by fluidized bed drying, tempering and ambient air cooling. Experimental results showed that after the three processes, moisture content was reduced from 33 % to 16.5 % dry-basis within approximately 53 minutes. During the first process, a fluidized-bed dryer was used to reduce the moisture content of paddy down to 19.5 % dry-basis within 3 minutes. Then the paddy was tempered for 30 minutes. Finally, it was cooled by ambient air (temperature and relative humidity of 30 °C and 55-60% respectively) with air velocity of 0.15 m/s for 20 minutes. Quality of paddy in terms of head rice yield and whiteness was acceptable.     

MOBILE FLUIDIZED BED PADDY DRYER

The objectives of this research are to design, construct and test a mobile fluidized bed paddy dryer with a drying capacity of 2.5-4.0 t/h. Suitable drying conditions are recommended as follows : drying capacity 3.8 t/h, bed velocity 2.8 m/s, average drying air temperature 144 °C, bed height 13.5 cm, fraction of air recycled 0.8. Residence time of paddy was approximately 1.3 minutes. Test results showed that moisture content of paddy was reduced from 32.6 % dry-basis to 25.8 % dry-basis. Consumption of electrical power and diesel fuel was 12.9 kW and 21.71 1/h respectively. Primary energy consumption was 910.9 MJ/h. The dryer could evaporate water 218.8 kg/h. Specific primary energy consumption was 4.2 MJ/kg-water evaporated. Cost of paddy drying was 1.48 baht/kg-water evaporated of which 0.53 was fixed cost and 0.95 was energy cost (US$1 =34baht).     

MOBILE FLUIDIZED BED PADDY DRYER

ABSTRACT

The objectives of this research are to design, construct and test a mobile fluidized bed paddy dryer with a drying capacity of 2.5-4.0 t/h. Suitable drying conditions are recommended as follows : drying capacity 3.8 t/h, bed velocity 2.8 m/s, average drying air temperature 144 °C, bed height 13.5 cm, fraction of air recycled 0.8. Residence time of paddy was approximately 1.3 minutes. Test results showed that moisture content of paddy was reduced from 32.6 % dry-basis to 25.8 % dry-basis. Consumption of electrical power and diesel fuel was 12.9 kW and 21.71 1/h respectively. Primary energy consumption was 910.9 MJ/h. The dryer could evaporate water 218.8 kg/h. Specific primary energy consumption was 4.2 MJ/kg-water evaporated. Cost of paddy drying was 1.48 baht/kg-water evaporated of which 0.53 was fixed cost and 0.95 was energy cost (US$1 =34baht).     

Cross-Flow Fluidized Bed Paddy Dryer: Prototype and Commercialization

ABSTRACT

The objective of this paper is to design and test a prototype, 0.82 ton/h capacity, fluidzed bed paddy dryer for high moisture paddy. Exhausted air is paritially recycled. Experimental results showed that the unit operated efficiently and yielded high product quality in terms of head yield and whiteness. In reducing the moisture content from 45% to 24% dry-basis using air temperature of 100–120°C, fraction of air recycled of 0.66, specific air flow rate of 0.05, kg/s-kg dry matter, superficial air velocity of 3.2 m/s, bed depth of 0.1 m, total primary energy consumption was 2.32 MJ/kg water evaporated of which 0.35 was primary energy from electricity (electrical energy multiplied by 2.6) and 1.79 was primary energy in terms of heat.     

Development of Cross-Flow Fluidized Bed Paddy Dryer

A cross-flow fluidized bed paddy dryer with a capacily of 200 kgh was designed, fabricated and tested. Experimental results showed that final moisture content of paddy should not be lower than 23 % dry-basis if quality is to be maintained. Drying air temperature was keot constant at 115°C according to the recommendation of previous work. Results obtained from the mathematical model developed in this study indicatedthat optimum operating parameters should be as follows : air speed of 2.3 m/s, bed thickness of 10 cm and fraction of air recycled of 80 %. At this condition, energy consumption was close to the minimum while drying capacity was near the maximum. A prototype fluidized bed dryer with a capacity of 1 t/h was designed, fabricated and installed with the collaboration of a private company. The unit has been used for almost the whole past harvesting season in 1994 at a paddy merchant sile with preference compared to conventional column continuous dryers. More than 300 tons of paddy were dried without any problems.     

Development of Cross-Flow Fluidized Bed Paddy Dryer

ABSTRACT

A cross-flow fluidized bed paddy dryer with a capacily of 200 kgh was designed, fabricated and tested. Experimental results showed that final moisture content of paddy should not be lower than 23 % dry-basis if quality is to be maintained. Drying air temperature was keot constant at 115°C according to the recommendation of previous work. Results obtained from the mathematical model developed in this study indicatedthat optimum operating parameters should be as follows : air speed of 2.3 m/s, bed thickness of 10 cm and fraction of air recycled of 80 %. At this condition, energy consumption was close to the minimum while drying capacity was near the maximum. A prototype fluidized bed dryer with a capacity of 1 t/h was designed, fabricated and installed with the collaboration of a private company. The unit has been used for almost the whole past harvesting season in 1994 at a paddy merchant sile with preference compared to conventional column continuous dryers. More than 300 tons of paddy were dried without any problems.     

Effect of Fluidized Bed Drying Temperature on Various Quality Attributes of Paddy

Abstract

As reported by many researchers, it was found that fluidized bed paddy drying using high drying air temperatures of over 100°C affected the head rice yield and whiteness of dried rice. However, only a few studies on fluidized bed paddy drying with drying air temperatures below 100°C were so far reported. The main objective of this work was therefore to study the effect of fluidized bed drying air temperature on various quality parameters of Suphanburi 1 and Pathumthani 1 Indica rice. Paddy was dried from the initial moisture contents of 25.0, 28.8, and 32.5% dry basis to 22.5 ± 1.2% dry basis using inlet drying air temperatures between 40 and 150°C at 10°C/step. After fluidized bed drying, paddy was tempered and followed by ambient air aeration until its final moisture content was reduced to 16.3 ± 0.5% dry basis. The results showed that the head rice yield of Suphanburi 1 was significantly related to the inlet drying temperature and initial moisture content whilst there was no significant relationship between the head rice yield, drying temperature and initial moisture content for Pathumthani 1. The whiteness of the two rice varieties was slightly decreased with increase in drying air temperature and initial moisture content. It was also found that the hardness of both cooked rice varieties exhibited insignificant difference (p < 0.05) comparing to rewetted rice, which was gently dried by ambient air aeration in thin layer. The thermal analysis by DSC also showed that partial gelatinization occurred during drying at higher temperatures. Using inlet drying air temperatures in the range of 40–150°C therefore did not affected the quality of cooked rice and paddy. The milling quality of paddy was also well maintained.     

DEHUMIDIFICATION DRYING OF HIGH-MOISTURE ROUGH RICE IN A RADIAL-FLOW, CIRCULAR BIN

An experimental radial-flow, circular bin dryer with a dehumidifier was fabricated and tested for rough rice drying. Results showed that high-moisture paddy could be dried to 14% moisture content (wet basis) over a 24 h drying span at an average drying rate of 0.5%/h. The open-cycle system's specific moisture extraction rate and the dehumidifier's coefficient of performance were within the usual range of values cited for similar conventional systems or equipment. The quality of the dehumidifier-dried and naturally dried paddy was similar with respect to minimum grain Assuring, The system was found to be a technically feasible, more energy-efficient and safer alternative to electrical resistance heating in the conditioning of ambient air for drying under humid tropical conditions.     

Rapid Drying of Parboiled Paddy Using Hot Air Impinging Stream Dryer

A method for rapid drying of parboiled paddy via the use of an impinging stream dryer was proposed and assessed. The effects of the drying air temperature, number of drying cycles, as well as time of tempering between each drying cycle on the moisture reduction, head rice yield, and whiteness index of the dried parboiled paddy were studied. The drying experiments were carried out at drying air temperatures of 130, 150, and 170°C; inlet air velocity of 20 m/s; impinging distance of 5 cm; and paddy feed rate of 40 kg_{dry_paddy}/h. Parboiled paddy was dried for up to seven cycles. Between each drying cycle the parboiled paddy was tempered for a period of either 0 (no tempering), 15, 30, 60, or 120 min. After impinging stream drying, paddy was ventilated by ambient air flow until its moisture content reached 16% (db). Moisture reduction of the paddy was noted to depend on both the impinging stream drying temperature and tempering time. Drying at a high temperature along with tempering for a suitable period of time could maintain the head rice yield of the paddy at a level similar to that of the reference parboiled paddy. To avoid discoloration and low head rice yield, parboiled paddy should not be dried at a temperature higher than 150°C and should be tempered for at least 30 min.     

Experiments on In-Store Paddy Drying Under Tropical Climate: Simulation and Product Quality

The main objective of this work is to study the rice whiteness and paddy qualities of rice in terms of hardness, stickiness, cohesiveness, and germination of rice. The prediction results of moisture content and whiteness are compared with the experimental results using a near-equilibrium drying model, which is modified by including whiteness kinetics of rice kernel. The long grain rice (Suphanburi 1 high amylose indica variety), which consists of 27% amylose was used for all experiments. The experiments were carried out at the average ambient temperature range of 28.6-30.8°C, average relative humidity of 65.2-80.6% with a fixed bed depth of 1.0 m. Specific air flow rates of 0.65 and 0.93 m³/min-m³ of paddy were forced continuously through the paddy bulk at initial moisture contents of 18.5% and 20.1% wet basis, respectively. The desired final moisture content of paddy is about 13.3 ± 0.6% wet basis. The results show that drying rate and the whiteness predictions are in good agreement with those from the experiments. The in-store drying using ambient air condition did not produce notable effect on the rice whiteness, head rice yield, and the percentage of paddy germination. However, the hardness, stickiness, and cohesiveness of rice were changed.     

DEHUMIDIFICATION DRYING OF HIGH-MOISTURE ROUGH RICE IN A RADIAL-FLOW,CIRCULAR BIN

Abstract

An experimental radial-flow, circular bin dryer with a dehumidifier was fabricated and tested for rough rice drying. Results showed that high-moisture paddy could be dried to 14% moisture content (wet basis) over a 24 h drying span at an average drying rate of 0.5%/h. The open-cycle system's specific moisture extraction rate and the dehumidifier's coefficient of performance were within the usual range of values cited for similar conventional systems or equipment. The quality of the dehumidifier-dried and naturally dried paddy was similar with respect to minimum grain Assuring, The system was found to be a technically feasible, more energy-efficient and safer alternative to electrical resistance heating in the conditioning of ambient air for drying under humid tropical conditions.     

DRYING CHARACTERISTICS OF CORN IN FLUIDIZED BED DRYER

A batch fluidized bed dryer was carried out for corn drying. Drying characteristics of corn were investigated The experimental results indicated that moisture transfer inside a corn kernel was controlled by internal diffusion by the following conditions : inlet hot air temperatures of 120 - 200 °C, superficial air velocities of 2.2- 4 m/s, bed depths of 4 - 12 cm, fraction of air recycled of 0.5 -0.9 and initial moisture content of corn of 43 % dry-basis. The Wang and Sing equation could describe in accordance with the results. Inlet hot air temperature and specific air flow rate were independent variables for drying constant model in the Wang and Singh equation.     

EFFECTS OF DRYING, TEMPERING AND AMBIENT AIR VENTILATION ON QUALITY AND MOISTURE REDUCTION OF CORN

The objective of this work is to study systematically how to decrease corn moisture content using processes consisting of fluidized bed drying, tempering and ambient air ventilation. Effects of drying, tempering and ventilation on moisture reduction and quality of dried corn in terms of stress crack, breakage and color are experimentally investigated. Experimental results show that stress crack depends on final moisture content of com. Tempering is found useful for increasing the quality of dried com after fluidized bed drying. The optimum tempering time is 40 minutes. Among the ambient air velocity ranging from 0.075 to 0.375 m/s, the appropriate velocity is 0.15 m/s. Final moisture content of com after ambient air ventilation is about 13.0 - 14.5 %(w.b.) with breakage and stress crack lower than 2% and 5% by wt., respectively. Slight change of color of dried corn is observed.     

Experiments on In-Store Paddy Drying Under Tropical Climate: Simulation and Product Quality

Abstract

The main objective of this work is to study the rice whiteness and paddy qualities of rice in terms of hardness, stickiness, cohesiveness, and germination of rice. The prediction results of moisture content and whiteness are compared with the experimental results using a near-equilibrium drying model, which is modified by including whiteness kinetics of rice kernel. The long grain rice (Suphanburi 1 high amylose indica variety), which consists of 27% amylose was used for all experiments. The experiments were carried out at the average ambient temperature range of 28.6–30.8°C, average relative humidity of 65.2–80.6% with a fixed bed depth of 1.0 m. Specific air flow rates of 0.65 and 0.93 m³/min-m³ of paddy were forced continuously through the paddy bulk at initial moisture contents of 18.5% and 20.1% wet basis, respectively. The desired final moisture content of paddy is about 13.3 ± 0.6% wet basis. The results show that drying rate and the whiteness predictions are in good agreement with those from the experiments. The in-store drying using ambient air condition did not produce notable effect on the rice whiteness, head rice yield, and the percentage of paddy germination. However, the hardness, stickiness, and cohesiveness of rice were changed.     

DRYING CHARACTERISTICS OF CORN IN FLUIDIZED BED DRYER

ABSTRACT

A batch fluidized bed dryer was carried out for corn drying. Drying characteristics of corn were investigated The experimental results indicated that moisture transfer inside a corn kernel was controlled by internal diffusion by the following conditions : inlet hot air temperatures of 120 - 200 °C, superficial air velocities of 2.2- 4 m/s, bed depths of 4 - 12 cm, fraction of air recycled of 0.5 -0.9 and initial moisture content of corn of 43 % dry-basis. The Wang and Sing equation could describe in accordance with the results. Inlet hot air temperature and specific air flow rate were independent variables for drying constant model in the Wang and Singh equation.     

Assessment of the Actual Performance of an Industrial Solar Kiln for Drying Timber

The aim of this study was to assess the actual performance of an instrumented industrial solar kiln for drying Australian hardwood timber (Eucalyptus pilularis) boards (270 × 43 mm). Ambient temperature and humidity, air temperature and humidity in the kiln, and wood moisture contents were recorded on site (Heron's Creek, NSW, Australia) using sensors and an electronic data acquisition and logging system. The average increases in air temperatures in the kiln compared with ambient conditions were 17.3°C (May-June), 13.8°C (July-August), 10°C (September-October), 8.2°C (November-March), and 7.5°C (March-May) for five runs monitored. Drying times were 2-4 months from initial moisture contents of 43 to 62% (dry-basis) to final moisture contents of 12 to 22%. Overall, the solar kiln has been shown to be an acceptable alternative to air-drying for pre-drying of Australian hardwood timber.     

EFFECTS OF DRYING ON HEAD RICE YIELD USING FLUIDIZATION TECHNIQUE

ABSTRACT

Experimental results of fluidized bed paddy drying using high inlet air temperatures (140 and 150 °C) showed that head rice yield could be increased to a maximum value at a range of paddy final moisture contents of 19 to 22 % wet-basis. In case of reducing moisture content of paddy to lower than 19 % wet-basis, head rice yield of tempered paddy was higher than that of no-tempered one. Initial moisture contents of paddy that could increase head rice yield were in a range of 23 to 31 % wet-basis. As initial moisture content increased head rice yield increased. Whiteness of dried paddy was mostly accepted. However, if tempering temperature was higher than 60 °C, it may cause the problems for trade.     

Development of a new pre-drying method of accelerated water absorption and partial gelatinization of starch in paddy using pulsed microwave-water applications in a microwave rotary drum dryer

The present study was undertaken to develop a pre-drying process of an accelerated water absorption and partial gelatinization of starch in paddy using pulsed microwave-water applications. The experiments on microwave-assisted water absorption by paddy (var. Sworn Masuri) at five power density levels in the range 0.2–1?kW?kg^?1 were conducted in a semi-pilot-scale microwave dryer. The paddy was exposed to pre-calculated intermittent water spray and pulsed microwaves up to 100?min. The water absorption kinetics were modeled using modified Azuara’s equation of mass transfer and the process was compared with traditional hot water soaking of the paddy at 60?°C for 3.33?h. The moisture content gained by paddy during microwave-assisted water absorption was faster (30% in 1.67?h) compared to hot water soaking (30% in 3.33?h). The consumption of water, specific energy, and water absorption time during microwave processing were reduced by 70%, 39.51%, and 50%, respectively. The method of slopes was used to estimate moisture diffusivity during microwave-assisted water absorption by paddy. X-ray diffraction (XRD) analysis and scanning electron microscopy (SEM) of treated paddy were done to understand the changes in the crystallinity and the microstructure of starch molecules. The microwave-assisted water absorption process was found to accelerate the moisture gain with the effect of partial gelatinization of starch in the paddy. Further, the experiment can be continued in the same microwave dryer to fully gelatinize the paddy at 30% moisture content and dry the gelatinized paddy.