Quantified NOx adsorption on Pt/K/gamma-Al2O3 and the effects of CO2 and H2O

A multi-component NO_x-trap catalyst consisting of Pt and K supported on γ-Al₂O₃ was studied at 250 °C to determine the roles of the individual catalyst components, to identify the adsorbing species during the lean capture cycle, and to assess the effects of H₂O and CO₂ on NO_x storage. The Al₂O₃ support was shown to have NO_x trapping capability with and without Pt present (at 250 °C Pt/Al₂O₃ adsorbs 2.3 μmols NO_x/m²). NO_x is primarily trapped on Al₂O₃ in the form of nitrates with monodentate, chelating and bridged forms apparent in Diffuse Reflectance mid-Infrared Fourier Transform Spectroscopy (DRIFTS) analysis. The addition of K to the catalyst increases the adsorption capacity to 6.2 μmols NO_x/m², and the primary storage form on K is a free nitrate ion. Quantitative DRIFTS analysis shows that 12% of the nitrates on a Pt/K/Al₂O₃ catalyst are coordinated on the Al₂O₃ support at saturation.

When 5% CO₂ was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by 45% after 1 h on stream due to the competition of adsorbed free nitrates with carboxylates for adsorption sites. When 5% H₂O was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by only 16% after 1 h, but the Al₂O₃-based nitrates decreased by 92%. Interestingly, with both 5% CO₂ and 5% H₂O in the feed, the total storage only decreased by 11%, as the hydroxyl groups generated on Al₂O₃ destabilized the K–CO₂ bond; specifically, H₂O mitigates the NO_x storage capacity losses associated with carboxylate competition.     

The activity and characterization of sol–gel Sn/Al2O3 catalyst for selective catalytic reduction of NOx in the presence of oxygen

Catalytic performance of Sn/Al₂O₃ catalysts prepared by impregnation (IM) and sol–gel (SG) method for selective catalytic reduction of NO_x by propene under lean burn condition were investigated. The physical properties of catalyst were characterized by BET, XRD, XPS and TPD. The results showed that NO₂ had higher reactivity than NO to nitrogen, the maximum NO conversion was 82% on the 5% Sn/Al₂O₃ (SG) catalyst, and the maximum NO₂ conversion reached nearly 100% around 425 °C. Such a temperature of maximum NO conversion was in accordance with those of NO_x desorption accompanied with O₂ around 450 °C. The activity of NO reduction was enhanced remarkably by the presence of H₂O and SO₂ at low temperature, and the temperature window was also broadened in the presence of H₂O and SO₂, however the NO_x desorption and NO conversion decreased sharply on the 300 ppm SO₂ treated catalyst, the catalytic activity was inhibited by the presence of SO₂ due to formation of sulfate species (SO₄²⁻) on the catalysts. The presence of oxygen played an essential role in NO reduction, and the activity of the 5% Sn/Al₂O₃ (SG) was not decreased in the presence of large oxygen.     

Characterization and performance of Pt-USY in the SCR of NOx with hydrocarbons under lean-burn conditions

Pt-USY was used for the selective catalytic reduction of NO_x with hydrocarbons in the presence of excess oxygen. The catalyst was prepared by an ion-exchange method and characterized by XRD, TEM, CO chemisorption, and Ar adsorption at 87 K. The platinum particle size distribution was found to be broad (2–20 nm), with no apparent sintering of the active phase during the HC-SCR process after 25 h time-on-stream. Generally, large metal clusters (>15 nm) are situated at the external surface of the zeolite, while the smaller ones are located in the pores of the support. Pt-USY shows an excellent activity in the deNO_x reaction (molar NO_x conversion 90% at 475 K) with propene as the reductant in 5 kPa O₂, as well as stable operation during time-on-stream. Propane only yields a low NO_x conversion compared to propene. The presence of high oxygen contents (5–10 kPa O₂) slightly inhibits the reaction. No significant decrease in deNO_x activity was observed at high space velocities (up to 100,000 h⁻¹). The presence of SO₂ and H₂O in the feed stream did not significantly affect the deNO_x activity. Pt-USY performs better under lean-burn conditions than other Pt-catalysts supported on e.g. ZSM-5, Al₂O₃, or SiO₂. The selectivity to N₂ was similar to the other Pt-based catalysts (30%), the other major product being N₂O.     

Multifunctional catalysts for de-NOx processes: The case of H3PW12O40·6H2O-metal supported on mixed oxides

The role of a multifunctional catalyst for de-NO_x process has been investigated. The NO_x storage capacity of H₃PW₁₂O₄₀·6H₂O (HPW) was improved by the presence of a noble metal (Pt, Rh or Pd). Both HPW and noble metal were deposited on a specific support (based on Zr–Ce or Zr–Ti). The presence of noble metal in several oxidation states, as evidenced by TPR and IR, involves the possibility of forming different catalytic sites: (i) M⁰ (zero-valent metal) and perhaps (ii) (metal–H)^δ+ from specific interactions between noble metal and the HPW proton. Supports were also able to adsorb and activate NO_x and to generate cationic catalytic sites (M^x+). These cationic sites seem to be the clue for their important activity toward NO_x reduction. This catalyst presents an outstanding resistance to SO₂ poisoning which can be related to NO and NO₂ absorption mechanism in HPW. The use of alternating short cycles of lean/rich mixtures allows us optimising the performance of this catalytic system in terms of both NO_x reduction capacity and NO_x storage efficiency: up to 48 and 84%, respectively (with a 2% CO + 1% H₂ mixture for reducing). Experimental results sustain two hypotheses: first, HPW-metal-support catalyst includes several (independent) catalytic functions required for a de-NO_x process to occur and second, the formation of oxygenate active species must be indispensable for NO_x reduction into nitrogen.     

Influence of CO2 and H2O on NOx storage and reduction on a Pt–Ba/γ-Al2O3 catalyst

In this paper, the effect of CO₂ and H₂O on NO_x storage and reduction over a Pt–Ba/γ-Al₂O₃ (1 wt.% Pt and 30 wt.% Ba) catalyst is shown. The experimental results reveal that in the presence of CO₂ and H₂O, NO_x is stored on BaCO₃ sites only. Moreover, H₂O inhibits the NO oxidation capability of the catalyst and no NO₂ formation is observed. Only 16% of the total barium is utilized in NO storage. The rich phase shows 95% selectivity towards N₂ as well as complete regeneration of stored NO. In the presence of CO₂, NO is oxidized into NO₂ and more NO_x is stored as in the presence of H₂O, resulting in 30% barium utilization. Bulk barium sites are inactive in NO_x trapping in the presence of CO₂·NH₃ formation is seen in the rich phase and the selectivity towards N₂ is 83%. Ba(NO₃)₂ is always completely regenerated during the subsequent rich phase. In the absence of CO₂ and H₂O, both surface and bulk barium sites are active in NO_x storage. As lean/rich cycling proceeds, the selectivity towards N₂ in the rich phase decreases from 82% to 47% and the N balance for successive lean/rich cycles shows incomplete regeneration of the catalyst. This incomplete regeneration along with a 40% decrease in the Pt dispersion and BET surface area, explains the observed decrease in NO_x storage.     

Combinatorial preparation and high-throughput catalytic tests of multi-component deNOx catalysts

A quaternary catalyst library of 56 samples comprising all combinations of four elements, viz. Ag, Co, Cu, In, with six equally spaced atomic fraction increments from 0 to 1 was prepared by impregnation of a proprietary mesoporous alumina support. Catalytic properties of the library were tested in the selective catalytic reduction (SCR) of NO_x by propane under lean conditions in the temperature range 400–500 °C. The catalytic data acquired by a parallel 64-channel microreactor system with automated time-of-flight mass spectrometric analysis have been evaluated regarding selectivity–compositional relationships, synergistic effects for NO_x conversion, and efficiency of propane utilization. Full conversion of NO_x is achieved over Ag–Co combinations at 450 °C with N₂ selectivities of more than 90% and reductant utilization of 20% in a feed of 1500 ppm NO, 1500 ppm propane and 5 vol.% O₂ (space velocity of 36,000 cm³ g_cat⁻¹ h⁻¹). For the single-component catalysts Ag/Al₂O₃, Co/Al₂O₃, Cu/Al₂O₃, and In/Al₂O₃, the state of the elements on the mesoporous alumina was characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM). Cobalt forms a spinel-like cobalt aluminate phase whereas copper and indium are present as oxides with small sizes not detectable by XRD. Silver occurs in both metallic state and as Ag₂O, and forms Ag_n clusters of at least two different sizes, predominantly with diameters of about 30 nm. The conclusions are consistent with the reducibility of the single-component catalysts samples by H₂. Surface area measurements and pore size distributions revealed reasonable modifications of the textural properties. The main pore size of the alumina support is decreased from 7 to ca. 5 nm after loading of the active components.     

Catalytic reduction of NOx with H2/CO/CH4 over PdMOR catalysts

Conversion of NO_x with reducing agents H₂, CO and CH₄, with and without O₂, H₂O, and CO₂ were studied with catalysts based on MOR zeolite loaded with palladium and cerium. The catalysts reached high NO_x to N₂ conversion with H₂ and CO (>90% conversion and N₂ selectivity) range under lean conditions. The formation of N₂O is absent in the presence of both H₂ and CO together with oxygen in the feed, which will be the case in lean engine exhaust. PdMOR shows synergic co-operation between H₂ and CO at 450–500 K. The positive effect of cerium is significant in the case of H₂ and CH₄ reducing agent but is less obvious with H₂/CO mixture and under lean conditions. Cerium lowers the reducibility of Pd species in the zeolite micropores. The catalysts showed excellent stability at temperatures up to 673 K in a feed with 2500 ppm CH₄, 500 ppm NO, 5% O₂, 10% H₂O (0–1% H₂), N₂ balance but deactivation is noticed at higher temperatures. Combining results of the present study with those of previous studies it shows that the PdMOR-based catalysts are good catalysts for NO_x reduction with H₂, CO, hydrocarbons, alcohols and aldehydes under lean conditions at temperatures up to 673 K.     

Effect of hydrogen on reaction intermediates in the selective catalytic reduction of NOx by C3H6

Selective catalytic reduction of NO_x by C₃H₆ in the presence of H₂ over Ag/Al₂O₃ was investigated using in situ DRIFTS and GC–MS measurements. The addition of H₂ promoted the partial oxidation of C₃H₆ to enolic species, the formation of –NCO and the reactions of enolic species and –NCO with NO_x on Ag/Al₂O₃ surface at low temperatures. Based on the results, we proposed reaction mechanism to explain the promotional effect of H₂ on the SCR of NO_x by C₃H₆ over Ag/Al₂O₃ catalyst.     

Selective oxidation of ammonia over copper-silver-based catalysts

A novel catalyst based on copper-silver was developed to solve the contradiction between the high conversion temperature of Cu-based catalyst and low N₂ selectivity of Ag-based catalyst during selective oxidation of ammonium gas. The Cu-Ag-based catalyst (Cu 5 wt.%-Ag 5 wt.%/Al₂O₃) displayed a relatively low complete conversion temperature (<320 °C) with a high N₂ selectivity (>95%). Increasing loading of Cu and Ag decreases N₂ selectivity. The low N₂ selectivity of Ag-based catalyst is possibly related to the formation of Ag₂O crystals. Improvement of N₂ selectivity of Ag-based catalyst was obtained by doping Cu to decrease crystallized Ag₂O phase. The temperature programmed reaction (TPR) data show that N₂O is the main byproduct of oxidation of ammonia at temperature lower than 200 °C. Two bands of nitrate species at 1541 and 1302 cm⁻¹ were observed on Ag 10 wt.%/Al₂O₃ at the temperature higher than 250 °C, which indicates the formation of NO_x during the selective catalytic oxidation of ammonia. No nitrate species was observed on Cu 10 wt.%/Al₂O₃ and Cu 5 wt.%-Ag 5 wt.%/Al₂O₃, while only one nitrate species (1543 cm⁻¹) existed on Cu 10 wt.%-Ag 10 wt.%/Al₂O₃. We proposed that mixing Ag with Cu inhibited the formation of NO_x during the selective catalytic oxidation of ammonia over Cu-Ag/Al₂O₃.     

Electrochemical beaviour of the solid ionic conductor Ag7I4PO4

Electrochemical investigation of the solid superionic conductor Ag₇I₄PO₄ (0.8 AgI + 0.2 Ag₃PO₄) at room temperature and at 40°C were performed by means of cyclic voltammetry, cyclic chronoamperometry and cyclic chronocoulometry, normal pulse polarography and ac polarography. It was shown that the Ag⁺ ↔ Ag redox process on Pt and Ag working electrode occurs with a certain overvoltage, ie that for Ag⁺ → Ag⁺ oxidation and the return of Ag⁺ ions into the electrolyte a certain overvoltage is necessary. From the determined values of the exchange current one estimates the redox process as a rather fast one. The silver working electrode is electrochemically inactive, while only cathodically deposited silver is electrochemically active and can be oxidized to Ag⁺ ions. Chronoamperometry and chronocoulometry show that there is a certain difference in the behaviour of Pt and Ag working electrodes due to uneven passivating anodic processes. On the basis of measurements of faradaic and capacitance currents and their dependence on frequency, diagrams of complex impedance of the Pt/Ag₇I₄PO₄ interface at various anodic and cathodic polarizations of the Pt electrode were plotted. The dependence of the serial capacity of the interface on the dc potential and temperature are discussed.     

Activity and stability of Ag–alumina for the selective catalytic reduction of NOx with methane in high-content SO2 gas streams

In this work, we investigated the activity and stability of Ag–alumina catalysts for the SCR of NO with methane in gas streams with a high concentration of SO₂, typical of coal-fired power plant flue gases. Ag–alumina catalysts were prepared by coprecipitation–gelation, and dilute nitric-acid solutions were used to remove weakly bound silver species from the surface of the as prepared catalysts after calcination. SO₂ has a severe inhibitory effect, essentially quenching the CH₄-SCR reaction on this type catalysts at temperatures <600 °C. SO₂ adsorbs strongly on the surface forming aluminum and silver sulfates that are not active for CH₄-SCR of NO_x. Above 600 °C, however, the reaction takes place without catalyst deactivation even in the presence of 1000 ppm SO₂. The reaction light-off coincides with the onset of silver sulfate decomposition, indicating the critical role of silver in the reaction mechanism. SO₂ is reversibly adsorbed on silver above 600 °C. While alumina sites remain sulfated, this does not hinder the reaction. Sulfation of alumina only decreases the extent of adsoption of NO_x, but adsorption of NO_x is not the limiting step. Methane activation is the limiting step, hence the presence of sulfur-free Ag–O–Al species is a requirement for the reaction. Strong adsorption of SO₂ on Ag–alumina decreases the rates of the reaction, and increases the activation energies of both the reduction of NO to N₂ and the oxidation of CH₄, the latter more than the former. Our results indicate partial contribution of gas phase reactions to the formation of N₂ above 600 °C. H₂O does not inhibit the reaction at 625 °C, and the effect of co-addition of H₂O and SO₂ is totally reversible.     

Transient behaviour of catalytic monolith with NOx storage capacity

Transient behaviour of catalytic monolith converter with NO_x storage is studied under conditions typical for automobiles with lean-burn engines (i.e., diesel and advanced gasoline ones). Periodical alternation of inlet concentrations is applied—NO_x are adsorbed on the catalyst surface during a long reductant-lean phase (2–3 min) and then reduced to N₂ within a short reductant-rich phase (2–6 s). Samples of industrial NO_x storage and reduction catalyst of NM/Ba/CeO₂/γ-Al₂O₃ type (NM = noble metal), washcoated on 400 cpsi cordierite substrate, are used in the study. Effects of the rich-phase length and composition on the overall NO_x conversions are examined experimentally. Reduction of NO_x by CO, H₂ and unburned hydrocarbons (represented by C₃H₆) in the presence of CO₂ and H₂O is considered.

Effective, spatially 1D, heterogeneous mathematical model of catalytic monolith with NO_x and oxygen storage capacity is described. The minimum set of experiments needed for the evaluation of relevant reaction kinetic parameters is discussed: (i) CO, H₂ and HC oxidation light-off under both lean and rich conditions, including inhibition effects, (ii) NO/NO₂ transformation, (iii) NO_x storage, including temperature dependence of effective NO_x storage capacity, (iv) water gas shift and steam reforming under rich conditions, i.e., in situ production of hydrogen, (v) oxygen storage and reduction, including temperature dependence of effective oxygen storage capacity, and (vi) NO_x desorption and reduction under rich conditions. The experimental data are compared with the simulation results.     

Impact of support oxide and Ba loading on the NOx storage properties of Pt/Ba/support catalysts: CO2 and H2O effects

A series of 1 wt.%Pt/_xBa/Support (Support = Al₂O₃, SiO₂, Al₂O₃-5.5 wt.%SiO₂ and Ce_0.7Zr_0.3O₂, x = 5–30 wt.% BaO) catalysts was investigated regarding the influence of the support oxide on Ba properties for the rapid NO_x trapping (100 s). Catalysts were treated at 700 °C under wet oxidizing atmosphere. The nature of the support oxide and the Ba loading influenced the Pt–Ba proximity, the Ba dispersion and then the surface basicity of the catalysts estimated by CO₂-TPD. At high temperature (400 °C) in the absence of CO₂ and H₂O, the NO_x storage capacity increased with the catalyst basicity: Pt/20Ba/Si < Pt/20Ba/Al5.5Si < Pt/10Ba/Al < Pt/5Ba/CeZr < Pt/30Ba/Al5.5Si < Pt/20Ba/Al < Pt/10BaCeZr. Addition of CO₂ decreased catalyst performances. The inhibiting effect of CO₂ on the NO_x uptake increased generally with both the catalyst basicity and the storage temperature. Water negatively affected the NO_x storage capacity, this effect being higher on alumina containing catalysts than on ceria–zirconia samples. When both CO₂ and H₂O were present in the inlet gas, a cumulative effect was observed at low temperatures (200 °C and 300 °C) whereas mainly CO₂ was responsible for the loss of NO_x storage capacity at 400 °C. Finally, under realistic conditions (H₂O and CO₂) the Pt/20Ba/Al5.5Si catalyst showed the best performances for the rapid NO_x uptake in the 200–400 °C temperature range. It resulted mainly from: (i) enhanced dispersions of platinum and barium on the alumina–silica support, (ii) a high Pt–Ba proximity and (iii) a low basicity of the catalyst which limits the CO₂ competition for the storage sites.     

Selective catalytic reduction of N2O and NOx in a single reactor in the nitric acid industry

The nitric acid industry is a source of both NO_x and N₂O. The simultaneous selective catalytic reduction of both compounds using propane as a reductant has been investigated. A stacked catalyst bed with first a Co-ZSM-5 catalyst and second a Pd/Fe-ZSM-5 catalyst gives >80% conversion of N₂O and NO_x above 300 °C at atmospheric pressure. At 4 bar absolute pressure (bara) the Co-ZSM-5 DeNO_x catalyst shows higher NO_x and propane conversion. This leaves not enough propane for the Pd/Fe-ZSM-5 DeN₂O catalyst, which causes a ‘dip’ in N₂O conversion. Reducing the space velocity (SV) of the first catalyst bed secures high NO_x and N₂O conversions from 300 °C and up at 4 bara.     

Transient analysis of the release and reduction of NOx using a Pt/Ba/Al2O3 catalyst

The release and reduction of NO_x in a NO_x storage-reduction (NSR) catalyst were studied with a transient reaction analysis in the millisecond range, which was made possible by the combination of pulsed injection of gases and time resolved time-of-flight mass spectrometry. After an O₂ pulse and a subsequent NO pulse were injected into a pellet of the Pt/Ba/Al₂O₃ catalyst, the time profiles of several gas products, NO, N₂, NH₃ and H₂O, were obtained as a result of the release and reduction of NO_x caused by H₂ injection. Comparing the time profiles in another analysis, which were obtained using a model catalyst consisting of a flat 5 nmPt/Ba(NO₃)₂/cordierite plate, the release and reduction of NO_x on Pt/Ba/Al₂O₃ catalyst that stored NO_x took the following two steps; in the first step NO molecules were released from Ba and in the second step the released NO was reduced into N₂ by H₂ pulse injection. When this H₂ pulse was injected in a large amount, NO was reduced to NH₃ instead of N₂.

A only small amount of H₂O was detected because of the strong affinity for alumina support. We can analyze the NO_x regeneration process to separate two steps of the NO_x release and reduction by a detailed analysis of the time profiles using a two-step reaction model. From the result of the analysis, it is found that the rate constant for NO_x release increased as temperature increase.     

High temperature catalytic combustion of methane and propane over hexaaluminate catalysts: NOx emission characteristics

Several hexaaluminate-related materials were prepared via hydrolysis of alkoxide and powder mixing method for high temperature combustion of CH₄ and C₃H₈, in order to investigate the effect of the concentration of the fuels, O₂ and H₂O on NO_x emission and combustion characteristics. Among the hexaaluminate catalysts, Sr_0.8La_0.2MnAl₁₁O₁₉₋ prepared by the alkoxide method exhibited the highest activity for methane combustion and low NO_x emission capability. NO_x emission at 1500 °C was increased linearly with O₂ concentration, whereas water vapor addition decreased NO_x emission in CH₄ combustion over the Sr_0.8La_0.2MnAl₁₁O₁₉₋ catalyst. In the catalytic combustion of C₃H₈ over the Sr_0.8La_0.2MnAl₁₁O₁₉₋ catalyst, the amount of NO_x emitted was raised in the temperature range between 1000 and 1500 °C when the C₃H₈ concentration increased from 1 to 2 vol.%. It was found that NO_x emission in this temperature range was reduced effectively by adding water vapor.     

Regeneration of NOx trap catalysts

We have investigated the regeneration of a nitrated or sulphated model Pt/Ba-based NO_x trap catalyst using different reductants. H₂ was found to be more effective at regenerating the NO_x storage activity especially at lower temperature, but more importantly over the entire temperature window after catalyst ageing. When the model NO_x storage catalyst is sulphated in SO₂ under lean conditions at 650 °C almost complete deactivation can be seen. Complete regeneration was not achieved, even under rich conditions at 800 °C in 10% H₂/He. Barium sulphate formed after the high temperature ageing was partly converted to barium sulphide on reduction. However, if the H₂ reduced sample was exposed to a rich condition in a gas mixture containing CO₂ at 650 °C, the storage activity can be recovered. Under these rich conditions the S²⁻ species becomes less stable than the CO₃²⁻, which is active for storing NO_x. Samples which were lean aged in air containing 60 ppm SO₂ at <600 °C, after regeneration at λ=0.95 at 650 °C, have a similar activity window to a fresh catalyst. It is, therefore, important that CO₂ is present during the rich regenerations of the sulphated model samples (as of course it would be under real conditions), as suppression of carbonate formation can lead to sulphide formation which is inactive for NO_x storage.     

The low-temperature performance of NOx storage and reduction catalyst

The catalytic performance and the behavior of NO_x storage and reduction (NSR) over a model catalyst for lean-burn gasoline engines have been mainly investigated and be discussed based on the temperature and reducing agents use in this study. The experimental results have shown that the NO_x storage amount in the lean atmosphere was the same as the NO_x reduction amount from the subsequent rich spike (RS) above the temperature of 400 °C, while the former was greater than the latter below the temperature of 400 °C. This indicated that when the temperature was below 400 °C compared with the NO_x storage stage, the reduction of the stored NO_x is somehow restricted. We found that the reduction efficiencies with the reducing agents decrease in the order H₂ > CO > C₃H₆ below 400 °C, thus not all of the NO_x storage sites could be fully regenerated even using an excessive reducing agent of CO or C₃H₆, which was supplied to the NSR catalyst, while all the NO_x storage sites could be fully regenerated if an adequate amount of H₂ was supplied. We also verified that the H₂ generation more favorably occurred through the water gas shift reaction than through the steam reforming reaction. This difference in the H₂ generation could reasonably explain why CO was more efficient for the reduction of the stored NO_x than C₃H₆, and hinted as a promising approach to enhance the low-temperature performance of the current NSR catalysts though promoting the H₂ generation reaction.     

Combined effect of H2O and SO2 on V2O5/AC catalysts for NO reduction with ammonia at lower temperatures

Combined effect of H₂O and SO₂ on V₂O₅/AC the activity of catalyst for selective catalytic reduction (SCR) of NO with NH₃ at lower temperatures was studied. In the absence of SO₂, H₂O inhibits the catalytic activity, which may be attributed to competitive adsorption of H₂O and reactants (NO and/or NH₃). Although SO₂ promotes the SCR activity of the V₂O₅/AC catalyst in the absence of H₂O, it speeds the deactivation of the catalyst in the presence of H₂O. The dual effect of SO₂ is attributed to the SO₄²⁻ formed on the catalyst surface, which stays as ammonium-sulfate salts on the catalyst surface. In the absence of H₂O, a small amount of ammonium-sulfate salts deposits on the surface of the catalyst, which promote the SCR activity; in the presence of H₂O, however, the deposition rate of ammonium-sulfate salts is much greater, which results in blocking of the catalyst pores and deactivates the catalyst. Decreasing V₂O₅ loading decreases the deactivation rate of the catalyst. The catalyst can be used stably at a space velocity of 9000 h⁻¹ and temperature of 250 °C.     

The removal of NOx from a lean exhaust gas using storage and reduction on H3PW12O40·6H2O

NO_x sorption and reduction capacities of 12-tungstophosphoric acid hexahydrate (H₃PW₁₂O₄₀·6H₂O, HPW) were measured under representative alternating conditions of lean and rich exhaust-type gas mixture. Under lean conditions, the sorption of NO_x is large and is equivalent to 37 mg of NO_x/g_HPW. Although a part of these NO_x remains unreduced, HPW is able to reduce some of the NO_x to produce N₂ by a reaction between the sorbed NO₂ and hydrocarbon (HC), but this process is slow. The addition of 1% Pt affects strongly the chemical behaviour occurring during the course of a rich operation. The NO desorption observed at the beginning of the rich phase is strongly accelerated. The direct correlation between NO₂ consumption and CO₂ production shows that the principal pathway is the reaction CO+NO₂→CO₂+NO. In a mixture of reducing gas (CO, HC, H₂), the competition is strongly in favour of CO though in its absence the reaction observed was the hydrogenation of propene to propane.