The effect of blending on the self‐healing behavior of an ethylene/methacrylic acid copolymer ionomer is investigated. Binary EMNa/EVA and EMNa/ENR blends are studied by ballistic puncture tests. In the composition range explored (15–50 wt% of EVA and ENR), the self‐healing characteristics decrease with increasing amount of EVA but are maintained in the whole range for EMNa/ENR blends. The bullet impact zones were observed using OM. Tensile tests showed that the blending process gives the opportunity to tune the mechanical characteristics without significant loss in the self‐healing properties, particularly in EMNa/ENR blends. Component compatibility, blend morphology and thermal properties were studied using DSC, SEM, and DMTA. Molecular interactions between the phases in the blends are discussed.
In order to improve some inferior physical properties of bacterial poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) [P(3HB‐co‐3HHx)] by blending with PEO, the miscibility, spherulite morphology, crystallization behavior and mechanical properties of P(3HB‐co‐3HHx)/PEO binary biodegradable polymer blends were investigated. A good miscibility between P(3HB‐co‐3HHx) with a 3HHx unit content of 11 mol‐% and PEO in the amorphous state was found when the PEO weight fraction was 10 wt.‐%, while the miscibility decreased dramatically when the PEO weight fraction exceeded 20 wt.‐%. Strongly depending on the blend composition, the mechanical properties of P(3HB‐co‐3HHx) was found to be significantly improved by blending with PEO with a weight fraction of ≈5–17.5 wt.‐%.
The effectiveness and efficiency of an ethylene/acrylate copolymer in toughening semicrystalline and amorphous PLA through melt blending is studied. The mechanical properties, phase morphologies, miscibilities, and toughening mechanisms of the blends are assessed. The ethylene/acrylate impact modifier effectively improved the impact strength of the blends, regardless of the PLA type. The semicrystalline blends showed decreased tensile strength and modulus with increased impact modifier content. In contrast, the ductility, elongation at break, and energy to break increased significantly. The relatively low BDT temperature obtained for the PLA blends renders the ethylene/acrylate copolymer impact modifier a desirable additive to toughen PLA for use in cold temperatures.
This paper analyzes the thermal and thermo‐oxidative degradation behavior, phase separation, melting, and crystallization of blends consisting of isotactic poly(propylene) (IPP) and poly(propylene) grafted with maleic anhydride (PP‐g‐MA). It has been established that, depending on the blend composition and crystallization/preparation procedure, the blends of IPP and PP‐g‐MA can either co‐crystallize or evidence phase separation. This conclusion has been attained by comparing the DSC results of crystallization under dynamic and isothermal conditions with X‐ray diffraction results. On the basis of the obtained results, the optimum mixing ratios have been established as 95–85 wt.‐% IPP/5–15 wt.‐% PP‐g‐MA. Thermo‐oxidative behavior has been studied by thermogravimetry and differential thermal analysis.
Ternary systems consisting of blends of polycarbonate (PC) from bisphenol A and minority amounts of an amorphous polyamide reinforced with organically modified nanoclay (naPA), were obtained in the melt state. The nanoclay was widely exfoliated inside the dispersed naPA phase. The dispersed phase exhibited a very fine size (up to 0.36 µm), indicating compatibilization. Compatibilization was attributed to interactions between the aPA and the PC. The nanocomposite showed a lower compatibility than their corresponding blends. This lower compatibility of the nanocomposite was attributed to a hindrance of the interaction by the migrated surfactant of the organoclay. The presence of fibrillation in conjunction with a dispersed nanoclay resulted in additive enhancing effects on the modulus and yield stress. This led to modulus increases up to 46% with respect to that of the neat matrix upon the addition of 25% naPA‐10. Besides exhibiting these remarkable modulus values, these systems show an elongation at break similar to that of the neat PC matrix.
The influence of blend composition on the phase structure and morphology of poly(propylene)/poly(ethylene‐co‐octene) blends was studied using SEM. A diameter dg was defined and calculated in real space to discuss the phase structure and morphology of iPP/PEOc blends. The figure‐estimation method was introduced to determine the distribution width of dg. It was shown that the distribution of dg obeys a log‐normal distribution and the distribution width σ of dg was calculated. In wave‐number (h) space, the correlation distance, ac, was defined by applying light scattering theory to power spectrum images obtained by 2D Fourier transformation. Moreover, a fractal dimension, Dc, was introduced to describe the uniformity of the spatial distribution.
Ultra‐thin fibers, consisting of blends of a PPE derivative and polystyrene, with average diameters ranging from 430 to 1 200 nm, were produced by electrospinning. The electrospinnability was significantly improved by adding pyridinium formate to the spinning solution. FT‐IR spectroscopy was used to confirm the composition of the electrospun fibers and their morphology was probed by SEM. The optical properties of the as‐prepared solutions, pristine and annealed fibers, and corresponding spin‐coated and solution‐cast films were investigated by UV‐vis spectroscopy. A comparison of the PL emission spectra revealed aggregation of PPE molecules in the electrospun materials but the extent of aggregation can be reduced if the materials are annealed above the glass transition temperature.
The effect of OMLS incorporation on the thermal properties of PET/LCP blends is studied. Pure and OMLS‐modified PET/LCP blends were prepared by melt‐extrusion using twin‐screw extruder. The morphological analyses of PET/LCP blends show that OMLS addition enhances the phase‐separated structure of the pure blend. A detailed study on the thermal properties of the pure and OMLS‐modified PET/LCP blends were carried out by means of DSC in both conventional and modulation modes. Results show a complex melting behaviour comprises of successive melting and re‐crystallisation. Finally, non‐isothermal crystal‐growth kinetics of pure and OMLS‐modified blends were investigated.
Plastic foams with nano/micro‐scale cellular structures were prepared from poly(propylene)/thermoplastic polystyrene elastomer (PP/TPS) systems, specifically the copolymer blends PP/hydrogenated polystyrene‐block‐polybutadiene‐block‐polystyrene rubber and PP/hydrogenated polystyrene‐block‐polyisoprene‐block‐polystyrene. These PP/TPS systems have the unique characteristic that the elastomer domain can be highly dispersed and oriented in the machine direction by changing the draw‐down ratio in the extrusion process. A temperature‐quench batch physical foaming method was used to foam these two systems with CO2. The cell size and location were highly controlled in the dispersed elastomer domains by exploiting the differences in CO2 solubility, diffusivity, and viscoelasticity between the elastomer domains and the PP matrix. The average cell diameter of the PP/TPS blend foams was controlled to be 200–400 nm on the finest level by manipulating the PP/rubber ratio, the draw‐down ratio of extrusion and the foaming temperature. Furthermore, the cellular structure could be highly oriented in one direction by using the highly‐oriented elastomer domains in the polymer blend morphology as a template for foaming.
The effects of varying concentrations of incorporated PDLA on the acceleration of PLLA homo‐crystallization due to stereocomplex (SC) crystallite formation are investigated in PLLA films doped with PDLA over the wide concentration range of 1–10 wt%. PLLA homo‐crystallization is accelerated for all the PDLA concentrations when the processing temperature Tp is just above the endset melting temperature of the SC crystallites (Tp = 226–238 °C), although the appropriate Tp range becomes narrow at low concentrations of PDLA. The accelerating effects of SC crystallites depend on the SC crystalline thickness and the interaction between the SC crystalline regions and PLLA amorphous regions for Tps below and above the melting peak temperature of the SC crystallites, respectively.
This work examined the miscibility, crystallization kinetics, melting behavior and crystal structure of syndiotactic polystyrene (sPS)/poly(styrene-co-α-methyl styrene) blends. Differential scanning calorimetry, polarized light microscopy and wide angle X-ray diffraction technique were used to approach the goals. The single composition-dependent Tgs of the blends and the melting temperature (Tm) depression of sPS in the blends indicated the miscible characteristic of the blend system at all compositions. Furthermore, the Tgs of the blends could be predicted by either of the Gordon–Taylor equation (with K=0.99) or the Fox equation with a slightly higher deviation. The dynamic and isothermal crystallization abilities of sPS were hindered with the incorporation of the miscible copolymer. Complex melting behavior was observed for melt-crystallized pure sPS and its blends as well. Nevertheless, the blends showed relatively simpler melting curves. Comparing with melt-crystallized samples, the cold-crystallized samples exhibited simpler melting behavior. The equilibrium melting temperature (Tm0) of β form sPS crystal determined from the conventional extrapolative method is 295.2 °C. The Flory–Huggins interaction parameter, χ, of the blends was estimated to be −0.27. The crystal morphology of sPS was disturbed in the blends. Only underdeveloped granular-like crystalline superstructure of sPS exhibited in cold-crystallized blends. Moreover, the existence of the copolymer in the blends apparently reduced the possibility of forming the less stable α form sPS crystals. 相似文献
Summary: Blends of poly(propylene) (PP) were prepared with poly[ethylene‐co‐(methyl acrylate)] (EMA) having 9.0 and 21.5% methyl acrylate comonomer. A similar series of blends were compatibilized by using maleic anhydride grafted PP. The morphology and mechanical properties of the blends were investigated using differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) in tensile mode. The DMA method and conditions were optimized for polymer film specimens and are discussed in the experimental section. The DSC results showed separate melting that is indicative of phase‐separated blends, analogous to other PP‐polyethylene blends but with the added polarity of methyl acrylate pendant side groups that may be beneficial for chemical resistance. Heterogeneous nucleation of PP was decreased in the blends because of migration of nuclei into the more polar EMA phase. The crystallinity and peak‐melting temperature did not vary significantly, although the width of the melting endotherm increased in the blends indicating a change had occurred to the crystals. DMA analysis showed the crystal‐crystal slip transition and glass transition (Tg) for PP as well as a Tg of the EMA copolymer occurring chronologically toward lower temperatures. The storage modulus of PP and the blends was generally greater with annealing at 150 °C compared with isothermal crystallization at 130 °C. The storage modulus of the blends for isothermally crystallized PP increased with 5% EMA, then decreased for higher amounts of EMA. Annealing caused a decrease with increasing copolymer content. The extent of the trend was greater for the compatibilized blends. The Tg of the blends varied over a small range, although this change was less for the compatibilized blends.
Storage modulus for PP and EMA9.0 blends annealed at 150 °C. 相似文献
The effects of process engineering in the fabrication of PHBV, PLA and their blends prepared by melt blending are studied. The elongation of an optimized blend can be improved by 148 and 250% over the virgin PHBV and PLA polymers, respectively. DSC shows that the two polymers are immiscible in blends of any composition. The crystallinity of PHBV is hindered by the presence of PLA. UV‐Vis demonstrates the opacity of the blend with incorporation of PHBV to the PLA phase. The observed tensile modulus of the optimized sample is compared with theoretical values from the rule of mixtures. Gordon‐Taylor's equation is applied on the glass transition temperatures for theoretical modeling to explain the miscibility of the polymers.
Blends of isotactic polystyrene (iPS) with non-crystallizable atactic polystyrene (aPS) were studied by differential scanning calorimetry and small angle X-ray scattering. The iPS/aPS blends, prepared by solution casting, were found to be miscible in the melt over the entire composition range. Both quenched amorphous and semicrystalline blends exhibit a single, composition-dependent glass transition temperature, depressed from that of either of the homopolymer components. Addition of aPS causes a decrease in crystallinity and in the rigid amorphous fraction, and suppression of the reorganization/recrystallization of iPS during thermal scanning: only one melting peak is observed for blends with larger aPS content. Formation and devitrification of the rigid amorphous fraction of iPS are also affected by aPS addition. The annealing peak, which is due to the relaxation of rigid amorphous fraction in parallel with melting of a tiny amount of crystals, is retarded with an increase of the composition of aPS, resulting in the slow devitrification of RAF in parallel with the melting of large amount of crystals. X-ray scattering shows that the long period in the iPS/aPS blends is greater than in the iPS homopolymer, and long period increases slightly as aPS content increases. Comparison of the volume fraction of phase 1 with the volume fraction crystallinity from DSC suggests that more and more amorphous phase is rejected outside the lamellar stacks as aPS content increases. The effect of aPS addition is to reduce the confinement of the amorphous phase chains. The cooperativity length, ξA, which is calculated from thermal analysis of the Tg region, increases with aPS addition. The interlamellar and extra-lamellar amorphous chains both contribute to the glass transition relaxation process. 相似文献
The objective of this research was to investigate the miscibility behavior of melamine‐formaldehyde resin and poly(vinyl acetate) blends for use as adhesives for surface materials in order to reduce formaldehyde emission. The investigation was conducted using differential scanning calorimetry, Fourier transform infrared spectroscopy, 13C CP/MAS solid state NMR, scanning electron microscope, atomic force microscopy and wide‐angle X‐ray scattering. Blends of various MF resin/PVAc weight compositions, comprising 0, 30, 50, 70 and 100%, were prepared in order to determine and compare the effect of PVAc content. These blends displayed a single cure temperature over the entire range of compositions indicating that this blend system was miscible in the amorphous phase due to the formation of hydrogen bonding between the amine groups of the MF resin and the carbonyl groups of PVAc. On the surface of the cured blends, the homogeneous dispersion of the PVAc phase in the MF resin was evident as small spherical domains and the blends were confirmed to be well combined.
Summary: Blends of single‐site catalysed ethylene‐α‐butene (C4VLDPE) and ethylene‐α‐octene (C8VLDPE) copolymers were prepared by melt extrusion. The phase morphology, thermal and mechanical properties of the blends have been investigated by differential scanning calorimetry (DSC), scanning electron microscopy (SEM), tensile test and dynamic mechanical analysis (DMA). Depending on the composition and thermal history, significant differences in structure and behaviour were found. It was also found that some degree of co‐crystallization occurred for quenched blends; whereas most of the oven slowly cooled blends showed two well‐defined melting peaks, indicating that the slow cooling favoured partial segregation of the fractions with different degrees of branching to form two morphologies. Moreover, SEM revealed morphology of the thinner crystals distributed in‐between the thicker sheaf‐like crystals for the slowly cooled blends with 20–50% C8VLDPE. Therefore, the synergism in mechanical properties for the blends with 20–50% C8VLDPE is due to a combination of larger crystal size, more complete phase separation and interfacial interaction produced by the segregation effect of the slow cooling treatment. DMA studies showed that the storage modulus increased as the addition of C8VLDPE and modulus for the slowly cooled blends are about twice those measured for the quenched ones, indicating higher stiffness of the blends. The smooth shift of β relaxation temperature with addition of C8VLDPE for both sets of blends confirmed the miscibility in the amorphous phase.
SEM image of the C4VLDPE‐C8VLDPE (50/50) blend after oven slow cooling treatment. 相似文献
This paper deals with immiscible blends of poly(ethylene terephthalate) obtained by melt blending with polycarbonate. A large survey of the current knowledge in the field of these blends is presented. Resolved and unresolved issues concerning the effect of exchange reactions on the miscibility of the components are addressed. The experimental part of the paper focuses on the rheological behavior of PET/PC blends. Blends containing various polymer ratios were obtained by melt blending with and without transesterification catalysts. Oscillatory shear flow in the melt was used to characterize the rheology of the various samples. A plot of the oscillatory data, similar to the Van Gurp Palmen plot, is used to point out the broadening of the co‐continuity window when in situ compatibilization takes place.
Summary: Blends of PEI and PPSU were prepared directly during the plasticization step of an injection molding process throughout the full composition range. The molded blends were transparent and showed a single glass transition and no dispersed phase by SEM. These characteristics did not allow the presence of a single miscibilized phase to be inferred unambiguously due to the very similar Tgs and refractive indices of the two components of the blends. Miscibility was inferred after close observation of the position, height and area of the enthalpy relaxation peak of the 50/50 blend. The modulus of elasticity and yield stress changed linearly with composition, leading to polymer materials with intermediate characteristics. The linearity was attributed to the lack of decrease in free volume induced by mixing and to the similar orientation of the components before and after mixing. The PPSU presence only slightly reduced the known tendency towards brittle fracture of PEI under notched impact conditions, but the presence of a single amorphous phase led to an expected ductile behavior of the blends close to that predicted by the single rule of mixtures.
Break stress (?) and break strain (○) of PEI/PPSU blends as a function of composition. 相似文献
