Synthesis and characterization of copolymers based on poly(butylene terephthalate) and ethylene oxide‐poly(dimethylsiloxane)‐ethylene oxide

A series of thermoplastic elastomers based on ethylene oxide‐poly(dimethylsiloxane)‐ethylene oxide (EO‐PDMS‐EO), as the soft segment, and poly(butylene terephthalate) (PBT), as the hard segment, were synthesized by catalyzed two‐step, melt transesterification reaction of dimethyl terephthalate (DMT) with 1,4‐butanediol (BD) and α,ω‐dihydroxy‐(EO‐PDMS‐EO). Copolymers with a content of hard PBT segments between 40 and 90 mass % and a constant length of the soft EO‐PDMS‐EO segments were prepared. The siloxane prepolymer with hydrophilic terminal EO units was used to improve the miscibility between the polar comonomers, DMT and BD, and the nonpolar PDMS. The molecular structure and composition of the copolymers were determined by ¹H‐NMR spectroscopy, whereas the effectiveness of the incorporation of α,ω‐dihydroxy‐(EO‐PDMS‐EO) into the copolymer chains was verified by chloroform extraction. The effects of the structure and composition of the copolymers on the melting temperatures and the degree of crystallinity, as well as on the thermal degradation stability and some rheological properties, were studied. It was demonstrated that the degree of crystallinity, the melting and crystallization temperatures of the copolymers increased with increasing mass fraction of the PBT segments. The thermal stability of the copolymers was lower than that of PBT homopolymer, because of the presence of thermoliable ether bonds in the soft segments. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Copolymers based on poly(butylene terephthalate) and polycaprolactone‐block‐polydimethylsiloxane‐block‐polycaprolactone

A series of novel thermoplastic elastomers, based on poly(butylene terephthalate) (PBT) and polycaprolactone‐block‐polydimethylsiloxane‐block‐polycaprolactone (PCL‐PDMS‐PCL), with various mass fractions, were synthesized through melt polycondensation. In the synthesis of the poly(ester‐siloxane)s, the PCL blocks served as a compatibilizer for the non‐polar PDMS blocks and the polar comonomers dimethyl terephthalate and 1,4‐butanediol. The introduction of PCL‐PDMS‐PCL soft segments resulted in an improvement of the miscibility of the reaction mixture and therefore in higher molecular weight polymers. The content of hard PBT segments in the polymer chains was varied from 10 to 80 mass%. The degree of crystallinity of the poly(ester‐siloxane)s was determined using differential scanning calorimetry and wide‐angle X‐ray scattering. The introduction of PCL‐PDMS‐PCL soft segments into the polymer main chains reduced the crystallinity of the hard segments and altered related properties such as melting temperature and storage modulus, and also modified the surface properties. The thermal stability of the poly(ester‐siloxane)s was higher than that of the PBT homopolymer. The inclusion of the siloxane prepolymer with terminal PCL into the macromolecular chains increased the molecular weight of the copolymers, the homogeneity of the samples in terms of composition and structure and the thermal stability. It also resulted in mechanical properties which could be tailored. Copyright © 2010 Society of Chemical Industry     

Synthesis and characterization of novel urethane‐siloxane copolymers with a high content of PCL‐PDMS‐PCL segments

Novel polyurethane copolymers derived from 4,4′‐methylenediphenyl diisocyanate (MDI), 1,4‐butanediol (BD) and α,ω‐dihydroxy‐[poly(caprolactone)‐poly (dimethylsiloxane)‐poly(caprolactone)] (α,ω‐dihydroxy‐(PCL‐PDMS‐PCL); = 6100 g mol^?1) were synthesized by a two‐step polyaddition reaction in solution. In the synthesis of the polyurethanes, the PCL blocks served as a compatibilizer between the nonpolar PDMS blocks and the polar comonomers, MDI and BD. The synthesis of thermoplastic polyurethanes (TPU) with high soft segment contents was optimized in terms of the concentrations of the reactants, the molar ratio of the NCO/OH groups, and the time and temperature of the polyaddition reaction. The structure, composition, and hard MDI/BD segment length of the synthesized polyurethane copolymers were determined by ¹H, ¹³C‐NMR, and two‐dimensional correlation (COSY, HSQC, and HMBC) spectroscopy, while the hydrogen bonding interactions in the copolymers were analyzed by FT‐IR spectroscopy. The influence of the reaction conditions on the structure, molecular weight, thermal, and some physical properties was studied at constant composition of the reaction mixture. A change in the molar ratio of the NCO/OH groups and the reaction conditions modified not only the molecular weight of the synthesized polyurethanes, but also the microstructure and therefore the thermal and physical properties of the copolymers. It was demonstrated that only PCL segments with high soft segment contents crystallize, thereby showing spherulitic morphology. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

The effect of the mass ratio of hard and soft segments on some properties of thermoplastic poly(ester‐siloxane)s

A series of thermoplastic elastomers based on soft polydimethylsiloxane (PDMS) and hard poly(butylene terephthalate) (PBT) segments was synthesized using a two‐step transesterification reaction in the melt. The molar mass of the soft PDMS component was constant (M?_nPDMS = 1056 g mol^?1) while the starting reaction mixture compositions were varied to obtained copolymers with a mass ratio of hard to soft segments in the range from 70/30 to 40/60. The structure and composition of the copolymers was verified by ¹H NMR spectroscopy. It appeared that there was a pronounced molar mass maximum when the PBT content of the copolymers was approximately 60 mass%, whereas all samples were considerably inhomogeneous with respect to the distribution of the lengths of the hard segments. Differential scanning calorimetry (DSC) thermograms showed that the melting and crystallization temperature increased with increasing PBT content, as did the total degree of crystallinity, which was confirmed by wide‐angle X‐ray scattering (WAXS) analysis. Thermogravimetric analysis (TGA) performed in nitrogen gave subtle differences for samples of different composition, including that of the PBT homopolymer, whereas in oxygen these differences were more pronounced in the way the thermo‐oxidative stability of the obtained copolymers decreased with decreasing PBT content. Finally, it was shown that the hardness depended directly on the PBT content, ie the higher the PBT content, the greater the hardness of the corresponding copolymer. Copyright © 2004 Society of Chemical Industry     

The effect of segment length on some properties of thermoplastic poly(ester–siloxane)s

A series of novel thermoplastic elastomers, based on poly(dimethylsiloxane) (PDMS) as the soft segment and poly(butylene terephthalate) (PBT) as the hard segment, were synthesized by catalyzed two‐step, melt transesterification reactions of dimethyl terephthalate and methyl esters of carboxypropyl‐terminated poly(dimethylsiloxane)s (M?_n = 550–2170 g mol^?1) with 1,4‐butanediol. The lengths of both the hard and soft segments were varied while the weight ratio of the hard to soft segments in the reaction mixture was maintained constant (57/43). The molecular structure, composition and molecular weights of the poly(ester–siloxane)s were examined by ¹H NMR spectroscopy. The effectiveness of the incorporation of the methyl‐ester‐terminated poly(dimethylsiloxane)s into the copolymer chains was verified by chloroform extraction. The effect of the segment length on the transition temperatures (T_m and T_g) and the thermal and thermo‐oxidative degradation stability, as well as the degree of crystallinity and hardness properties of the synthesized TPESs, were studied. Copyright © 2003 Society of Chemical Industry     

Synthesis and characterization of thermoplastic poly(ester–siloxane)s

Two series of thermoplastic poly(ester–siloxane)s, based on poly(dimethylsiloxane) (PDMS) as the soft segment and poly(butylene terephthalate) as the hard segment, were synthesized by two‐step catalyzed transesterification reactions in the melt. Incorporation of soft poly(dimethylsiloxane) segments into the copolyester backbone was accomplished in two different ways. The first series was prepared based on dimethyl terephthalate, 1,4‐butanediol and silanol‐terminated poly(dimethylsiloxane) (PDMS‐OH). For the second series, the PDMS‐OH was replaced by methyl diesters of carboxypropyl‐terminated poly(dimethylsiloxane)s. The syntheses were optimized in terms of both the concentration of catalyst, tetra‐n‐butyl‐titanate (Ti(OBu)₄), and stabilizer, N,N′‐diphenyl‐p‐phenylene‐diamine, as well as the reaction time. The reactions were followed by measuring the inherent viscosities of the reaction mixture. The molecular structures of the synthesized poly(ester–siloxane)s were verified by ¹H NMR spectroscopy, while their thermal properties were investigated using differential scanning calorimetry. © 2001 Society of Chemical Industry     

Characterization and comparison of diblock and triblock amphiphilic copolymers of poly(δ‐valerolactone)

Three types of pegylated amphiphilic copolymers of poly(δ‐valerolactone) (PVL) were copolymerized with methoxy poly(ethylene glycol) (MePEG) and poly(ethylene glycol) (PEG₄₀₀₀ and PEG_10,000), respectively. Pegylation of PVL allowed copolymers possessing amphiphilic property and efficiently self‐assembled to form micelles with a low critical micelle concentration (CMC) in the range of 10^?7–10^?8M. The average molecular weight of copolymers was in the range of 10,000–20,000 Da, and the polydispersity of copolymers was about 1.7–1.8. Higher mobility of low molecular weight PEG (i.e., MePEG and PEG₄₀₀₀) than high molecular weight PEG_10,000 allowed valerolactone ring opening more efficient in terms of PVL/MePEG and PVL/PEG₄₀₀₀ copolymers possessing longer chain length in hydrophobic domain. Pegylated PVL with low CMC and triblock structure was preferred to encapsulate drug during micelle formation. Although all of these amphiphilic copolymers exhibited controlled release character, the micelles formed by triblock copolymer possessed a more stable core‐shell conformation than that by diblock copolymer, and resulted in the release of drug from triblock micelles slower than that from diblock micelles. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1836–1841, 2006     

Crystallization kinetics of poly(1,4‐butylene‐co‐ethylene terephthalate)

The crystallization kinetics of poly(butylene terephthalate) (PBT), poly(ethylene terephthalate) (PET), and their copolymers poly(1,4‐butylene‐co‐ethylene terephthalate) (PBET) containing 70/30, 65/35 and 60/40 molar ratios of 1,4‐butanediol/ethylene glycol were investigated using differential scanning calorimetry (DSC) at crystallization temperatures (T_c) which were 35–90 °C below equilibrium melting temperature . Although these copolymers contain both monomers in high proportion, DSC data revealed for copolymer crystallization behaviour. The reason for such copolymers being able to crystallize could be due to the similar chemical structures of 1,4‐butanediol and ethylene glycol. DSC results for isothermal crystallization revealed that random copolymers had a lower degree of crystallinity and lower crystallite growth rate than those of homopolymers. DSC heating scans, after completion of isothermal crystallization, showed triple melting endotherms for all these polyesters, similar to those of other polymers as reported in the literature. The crystallization isotherms followed the Avrami equation with an exponent n of 2–2.5 for PET and 2.5–3.0 for PBT and PBETs. Analyses of the Lauritzen–Hoffman equation for DSC isothermal crystallization data revealed that PBT and PET had higher growth rate constant G_o, and nucleation constant K_g than those of PBET copolymers. © 2001 Society of Chemical Industry     

Effect of annealing on poly(urethane‐siloxane) copolymers

Poly(urethane‐siloxane) copolymers were prepared by copolymerization of OH‐terminated polydimethylsiloxane (PDMS), which was utilized as the soft segment, as well as 4,4′‐diphenylmethane diisocyanate (MDI) and 1,4‐butanediol (1,4‐BD), which were both hard segments. These copolymers exhibited almost complete phase separation between soft and hard segments, giving rise to a very simple material structure in this investigation. The thermal behavior of the amorphous hard segment of the copolymer with 62.3% hard‐segment content was examined by differential scanning calorimetry (DSC). Both the T₁ temperature and the magnitude of the T₁ endotherm increased linearly with the logarithmic annealing time at an annealing temperature of 100°C. The typical enthalpy of relaxation was attributed to the physical aging of the amorphous hard segment. The T₁ endotherm shifted to high temperature until it merged with the T₂ endotherm as the annealing temperature increased. Following annealing at 170°C for various periods, the DSC curves presented two endothermic regions. The first endotherm assigned as T₂ was the result of the enthalpy relaxation of the hard segment. The second endothermic peak (T₃) was caused by the hard‐segment crystal. The exothermic curves at an annealing temperature of above 150°C exhibited an exotherm caused by the T₃ microcrystalline growth. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:5174–5183, 2006     

Preparation and characterization of crosslinked polyurethane‐block‐poly(trifluoropropylmethyl)siloxane elastomers with potential biomedical applications

A series of crosslinked polyurethane‐block‐poly(trifluoropropylmethyl)siloxane elastomers were prepared via two steps. First, poly(trifluoropropylmethyl)siloxane polyurethane (FSPU) prepolymers were synthesized with α,ω‐bis(3‐aminopropyldiethoxylsilane) poly(trifluoropropylmethyl)siloxane (APFS) and toluenediisocyanate (TDI) and then capped with butanediol to generate the macromolecular FSPU diol extender. Second, polyurethane prepolymers synthesized from poly(tetramethylene oxide) and TDI were reacted with FSPU diol extenders with different ratios. The copolymers formed films through moisture curing and were characterized by Fourier transform infrared spectroscopy, DSC, dynamic mechanical analysis, TGA, mechanical testing etc. It is found that the equivalent ratio of reactants gives rise to a high molecular weight of copolymers and that low molecular weight APFS in the copolymers can form a certain number of silicon–oxygen crosslinks resulting from silicon alkoxy to produce higher tensile strength elastomers. The material thus has higher thermal stability and a more stable surface performance. The copolymers are then good candidates for biomedical applications.© 2013 Society of Chemical Industry     

A new macroinitiator for the synthesis of triblock copolymers PA12‐b‐PDMS‐b‐PA12

A new PDMS macroinitiator is proposed for the anionic ring‐opening polymerization of lactams. This α,ω‐dicarbamoyloxy caprolactam PDMS macroinitiator was readily obtained in quantitative yield, by an original synthesis scheme in two steps, which involved the scarcely reported reaction of isocyanates with silanol groups. It was then shown that this bifunctional macroinitiator enabled to synthesize triblock copolymers PA12‐b‐PDMS‐b‐PA12 by polymerization of lauryl lactam (LL) at high temperature (200°C) in inert atmosphere under conditions compatible with reactive extrusion processes. Another related high molar weight α,ω‐diacyllactam PDMS macroinitiator was also successfully used in the polymerization of LL under the same conditions, therefore overcoming the limitations formerly reported for this type of macroinitiators during the polymerization ε‐caprolactam (ε‐CL) at a much lower temperature (80°C). Triblock copolymers with a wide range of PA12 /molar weights (M_n: ～ 10,800–250,000 Da) were eventually obtained by using both types of macroinitiators. DMTA and DSC analyses showed that their thermal properties were strongly dependent upon their respective contents in soft and hard blocks. Such triblock copolymers already appear very promising for the highly effective in situ compatibilization of PA12/PDMS blends as shown by recent complementary results obtained in our laboratory. © 2006 Wiley Periodicals, Inc. J Appl PolymSci 102: 2818–2831, 2006     

Synthesis and characterization of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers with dibutylmagnesium as catalyst

Two series of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers were prepared by the ring opening polymerization of ε‐caprolactone in the presence of poly(ethylene glycol) and dibutylmagnesium in 1,4‐dioxane solution at 70°C. The triblock structure and molecular weight of the copolymers were analyzed and confirmed by ¹H NMR, ¹³C NMR, FTIR, and gel permeation chromatography. The crystallization and thermal properties of the copolymers were investigated by wide‐angle X‐ray diffraction (WAXD) and differential scanning calorimetry (DSC). The results illustrated that the crystallization and melting behaviors of the copolymers were depended on the copolymer composition and the relative length of each block in copolymers. Crystallization exothermal peaks (T_c) and melting endothermic peaks (T_m) of PEG block were significantly influenced by the relative length of PCL blocks, due to the hindrance of the lateral PCL blocks. With increasing of the length of PCL blocks, the diffraction and the melting peak of PEG block disappeared gradually in the WAXD patterns and DSC curves, respectively. In contrast, the crystallization of PCL blocks was not suppressed by the middle PEG block. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and surface properties of polydimethylsiloxane‐based block copolymers: poly[dimethylsiloxane‐block‐ (ethyl methacrylate)] and poly[dimethylsiloxane‐block‐(hydroxyethyl methacrylate)]

A polydimethylsiloxane (PDMS) macroazoinitiator was synthesized from bis(hydroxyalkyl)‐terminated PDMS and 4,4′‐azobis‐4‐cyanopentanoic acid by a condensation reaction. The bifunctional macroinitiator was used for the block copolymerization of ethyl methacrylate (EMA) and 2‐(trimethylsilyloxy)ethyl methacrylate (TMSHEMA) monomers. The poly(DMS‐block‐EMA) and poly(DMS‐block‐TMSHEMA) copolymers thus obtained were characterized using Fourier transform infrared and ¹H NMR spectroscopy and differential scanning calorimetry. After the deprotection of trimethylsilyl groups, poly(DMS‐block‐HEMA) and poly(DMS‐block‐EMA) copolymer film surfaces were analysed using scanning electron microscopy and X‐ray photoelectron spectroscopy. The effects of the PDMS concentration in the copolymers on both air and glass sides of films were examined. The PDMS segments oriented and moved to the glass side in poly(DMS‐block‐EMA) copolymer film while orientation to the air side became evident with increasing DMS content in poly(DMS‐block‐HEMA) copolymer film. The block copolymerization technique described here is a versatile and economic method and is also applicable to a wide range of monomers. The copolymers obtained have phase‐separated morphologies and the effects of DMS segments on copolymer film surfaces are different at the glass and air sides. Copyright © 2010 Society of Chemical Industry     

Synthesis and characterization of a poly(ether–ester) copolymer from poly(2,6 dimethyl‐1,4‐phenylene oxide) and poly(ethylene terephthalate)

A series of poly(ether–ester) copolymers were synthesized from poly(2,6 dimethyl‐1,4‐phenylene oxide) (PPO) and poly(ethylene terephthalate) (PET). The synthesis was carried out by two‐step solution polymerization process. PET oligomers were synthesized via glycolysis and subsequently used in the copolymerization reaction. FTIR spectroscopy analysis shows the coexistence of spectral contributions of PPO and PET on the spectra of their ether–ester copolymers. The composition of the poly(ether–ester)s was calculated via ¹H NMR spectroscopy. A single glass transition temperature was detected for all synthesized poly(ether–ester)s. T_g behavior as a function of poly(ether–ester) composition is well represented by the Gordon‐Taylor equation. The molar masses of the copolymers synthesized were calculated by viscosimetry. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Atom transfer radical polymerization of styrene and methyl (meth)acrylates initiated with poly(dimethylsiloxane) macroinitiator: Synthesis and characterization of triblock copolymers

Poly(dimethylsiloxane)(PDMS)‐based triblock copolymers were successfully synthesized via atom transfer radical polymerization (ATRP) initiated with bis(bromoalkyl)‐terminated PDMS macroinitiator (Br‐PDMS‐Br). First, Br‐PDMS‐Br was prepared by reaction between the bis(hydroxyalkyl)‐terminated PDMS and 2‐bromo‐2‐methylpropionyl bromide. PSt‐b‐PDMS‐b‐PSt, PMMA‐b‐PDMS‐b‐PMMA and PMA‐b‐PDMS‐b‐PMA triblock copolymers were then synthesized via ATRP of styrene (St), methyl methacrylate (MMA) and methyl acrylate (MA), respectively, in the presence of Br‐PDMS‐Br as a macroinitiator and CuCl/PMDETA as a catalyst system at 80 ^oC. Triblock copolymers were characterized by FTIR, ¹H‐NMR and GPC techniques. GPC results showed linear dependence of the number‐average molecular weight on the conversion as well as the narrow polydispersity indicies (PDI < 1.57) for the synthesized triblock copolymers which was lower than that of Br‐PDMS‐Br macroinitiator (PDI = 1.90), indicating the living/controlled characteristic of the reaction. Also, there was a very good agreement between the number‐average molecular weight calculated from ¹HNMR spectra and that calculated theoretically. Results showed that resulting copolymers have two glass transition temperatures, indicating that triblock copolymers have microphase separated morphology. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and characterization of hydroxy‐terminated polyether‐polydimethylsiloxane‐polyether (PE‐PDMS‐PE) triblock oligomers and their use in the preparation of thermoplastic polyurethanes

A series of hydroxy‐terminated polyether‐polydimethylsiloxane‐polyether (α,ω‐dihydroxy‐(PE‐PDMS‐PE)) ABA triblock oligomers were synthesized from silanic fluids and methyl polyallyloxide polyethers. The reaction was a one‐step solventless hydrosilylation reaction with chloroplatinic acid (CPA) catalyst in the presence of heat. These ABA oligomers were characterized via ¹H‐NMR, ¹³C‐NMR, ²⁹Si‐NMR, FT‐IR, and GPC to demonstrate that they exhibit a 100% linear ABA structure with a siloxane Si? O chain in the center and polyether ethylene oxide (EO)/propylene oxide (PO) chains on the two sides terminated by hydroxy groups. The triblock oligomers were used to form thermoplastic polyurethanes (TPUs) using two‐step solventless bulk polymerization. The investigation of triblock oligomers impact on TPUs mechanical properties, thermal performance, surface water repellency, and morphology performance were analyzed by Instron material tester, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), water contact angles (WCA), scanning electron microscope (SEM), and transmission electron microscope (TEM). DSC and TGA indicated that PE‐PDMS‐PE modified TPUs had a clear lower T_g under ?120°C and the temperature of 50% weight loss was improved from 280 to 340°C. PE‐PDMS‐PE–modified TPU did not have the marked reduction on mechanical properties than pure polyether produced TPU. Tensile strength was maintained at 13 MPa and elongation was maintained at 300%. SEM and TEM were used to investigate the copolymers’ morphology performance and found that all PO PE‐PDMS‐PE had a pseudo‐three phase separation. WCA analysis confirmed that PE‐PDMS‐PE–modified TPU had significantly improved hydrophobic performance because the silicone structure linked into TPU copolymers. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42521.     

Surface microphase separation in PDMS‐b‐PMMA‐b‐PHFBMA triblock copolymer films

Well‐defined poly(dimethylsiloxane)‐block‐poly(methyl methacrylate)‐block‐poly(2,2,3,3,4,4,4‐heptafluorobutyl methacrylate) (PDMS‐b‐PMMA‐b‐PHFBMA) triblock copolymers were synthesized via atom transfer radical polymerization (ATRP). Surface microphase separation in the PDMS‐b‐PMMA‐b‐PHFBMA triblock copolymer films was investigated. The microstructure of the block copolymers was investigated by transmission electron microscopy (TEM) and atomic force microscopy (AFM). Surface composition was studied by X‐ray photoelectron spectroscopy (XPS). The chemical composition at the surface was determined by the surface microphase separation in the PDMS‐b‐PMMA‐b‐PHFBMA triblock copolymer films. The increase of the PHFBMA content could strengthen the microphase separation behavior in the PDMS‐b‐PMMA‐b‐PHFBMA triblock copolymer films and reduce their surface tension. Comparison between the PDMS‐b‐PMMA‐b‐PHFBMA triblock copolymers and the PDMS‐b‐PHFBMA diblock copolymers showed that the introduction of the PMMA segments promote the fluorine segregation onto the surface and decrease the fluorine content in the copolymers with low surface energy. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effects of co‐hard segments on the microstructure and properties thermoplastic poly(ether ester) elastomers

A thermoplastic poly(ether ester) elastomer (TPEE) is composed of polyester hard segments and polyether soft segments. Polyester and polyether segments are often homopolymer segments. This work aims at incorporating poly(butylene phthalate (PBP) as co‐hard segments in the hard segments of poly(butylene terephthalate) (PBT)‐b‐poly(tetramethylene oxide) (PTMO) thermoplastic elastomer, and investigating structures and properties of the resulting materials, denoted as (PBT‐co‐PBP)‐b‐PTMO. (PBT‐co‐PBP)‐b‐PTMO was synthesized from dimethyl terephthalate (DMT), dimethyl phthalate (DMP), PTMO (M_n = 1000 g/mol), and 1,4‐butanediol (BDO). The crystallinity of (PBT‐co‐PBP)‐b‐PTMO first decreased and then increased with increasing PBP content from 5% to 10% due to a decrease in the average sequence length of the PBT hard segments. Its elongation at break was increased by 200–350%. When the mass fractions of PBT and PBP were 42% and 8%, respectively, the (PBT‐co‐PBP)‐b‐PTMO showed the best performance in terms of permanent deformation, strength, and hardness whose values were 30%, 25 MPa, and 37 D, respectively. All the synthesized copolymers had good thermal stability with a decomposition temperature of 400°C or so. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43337.     

Synthesis and characterization of polyrotaxanes comprising α‐cyclodextrins and poly(ε‐caprolactone) end‐capped with poly(butyl methacrylate)s

Biodegradable polyrotaxane‐based triblock copolymers were synthesized via the bulk atom transfer radical polymerization (ATRP) of n‐butyl methacrylate (BMA) initiated with polypseudo‐rotaxanes (PPRs) built from a distal 2‐bromoisobutyryl end‐capped poly(ε‐caprolactone) (Br‐PCL‐Br) with α‐cyclodextrins (α‐CDs) in the presence of Cu(I)Br/N,N,N′,N″,N″‐pentamethyldiethylenetriamine at 45 ºC. The structure was characterized in detail by means of ¹H NMR, gel permeation chromatography, wide‐angle X‐ray diffraction, DSC and TGA. When the feed molar ratio of BMA to Br‐PCL‐Br was changed from 128 to 300, the degree of polymerization of PBMA blocks attached to two ends of the PPRs was in the range 382 ? 803. Although about a tenth of the added α‐CDs were still threaded onto the PCL chain after the ATRP process, the movable α‐CDs made a marked contribution to the mechanical strength enhancement, blood anticoagulation activity and protein adsorption repellency of the resulting copolymers. Meanwhile, they could also protect the copolymers from the attack of H₂O and Lipase AK Amano molecules, exhibiting a lower mass loss as evidenced in hydrolytic and enzymatic degradation experiments. © 2013 Society of Chemical Industry     

PBT-b-PEO-b-PBT triblock copolymers: Synthesis,characterization and double-crystalline properties

We demonstrated here a facile method to synthesize novel double crystalline poly(butylene terephthalate)-block-poly(ethylene oxide)-block-poly(butylene terephthalate) (PBT-b-PEO-b-PBT) triblock copolymers by solution ring-opening polymerization (ROP) of cyclic oligo(butylene terephthalate)s (COBTs) using poly(ethylene glycol) (PEG) as macroinitiator and titanium isopropyloxide as catalyst. The structure of copolymers was well characterized by ¹H NMR and GPC. TGA results revealed that the decomposition temperature of PEO in triblock copolymers increased about 30 °C to the same as PBT copolymers, after being end-capped with PBT polymers. These triblock copolymers showed double crystalline properties from PBT and PEO blocks, observed from DSC and WAXD measurements. The melting and crystallization peak temperatures corresponding to PBT blocks increased with PBT content. The crystallization of PBT blocks showed the strong confinement effects on PEO blocks due to covalent linking of PBT blocks with PEO blocks, where the melting and crystallization temperatures and crystallinity corresponding to PEO blocks decreased significantly with increment of PBT content. The confinement effect was also observed by SAXS experiments, where the long distance order between lamella crystals decreases with increasing PBT length. For the triblock copolymer with highest PBT content (PBT₅₄-b-PEO₂₂₇-b-PBT₅₄), this effect shows a 30 °C depression on PEO crystals' melting temperature and 77% on enthalpy, respectively, compared to corresponding PEO homopolymer. The crystal morphology was observed by POM, and amorphous-like spherulites were observed during PBT crystallization.