A metamaterial hepta‐band antenna for wireless applications with specific absorption rate reduction

Present article embodies the design and analysis of slotted circular shape metamaterial loaded multiband antenna for wireless applications with declination of SAR. The electrical dimension is 0.260 λ × 0.253 λ × 0.0059 λ (35 × 34 × 0.8 mm³) of proposed design, at lower frequency of 2.23 GHz. The antenna consists of circular shape rectangular slot as the radiation element loaded with metamaterial split ring resonator (SRR) and two parallel rectangular stubs, etched rectangular single complementary split‐ring resonator (CSRR) and reclined T‐shaped slot as ground plane. Antenna achieves hepta bands for wireless standards WLAN (2.4/5.0/5.8 GHz), WiMAX (3.5 GHz), radio frequency identification (RFID) services (3.0 GHz), Upper X band (11.8 GHz—for space communication) and Lower K_U band (13.1 GHz—for satellite communication systems operating band). Stable radiation patterns are observed for the operating bands with low cross polarization. The SRR is responsible for creating an additional resonating mode for wireless application as well as provide the declination in SAR about 13.3%. Experimental characteristic of antenna shows close agreement with those obtained by simulation of the proposed antenna.     

Design and development of enhanced bandwidth multi‐frequency slotted antenna for 4G‐LTE/WiMAX/WLAN and S/C/X‐band applications

A multi‐frequency rectangular slot antenna for 4G‐LTE/WiMAX/WLAN and S/C/X‐bands applications is presented. The proposed antenna is comprised of rectangular slot, a pair of E‐shaped stubs, and an inverted T‐shaped stub and excited using staircase feed line. These employed structures help to achieve multiband resonance at four different frequency bands. The proposed multiband slot antenna is simulated, fabricated and tested experimentally. The experimental results show that the antenna resonates at 2.24, 4.2, 5.25, and 9.3 GHz with impedance bandwidth of 640 MHz (2.17‐2.82 GHz) covering WiMAX (802.16e), Space to Earth communications, 4G‐LTE, IEEE 802.11b/g WLAN systems defined for S‐band applications. Also the proposed antenna exhibits bandwidth of 280 MHz (4.1‐4.38 GHz) for Aeronautical and Radio navigation applications, 80 MHz (4.2‐4.28 GHz) for uncoordinated indoor systems,1060 MHz (5.04‐6.1 GHz) for the IEEE 802.11a WLAN system defined for C‐band applications and 2380 MHz (7.9‐10.28 GHz) defined for X‐band applications. Further, the radiation patterns for the designed antenna are measured in anechoic chamber and are found to agree well with simulated results.     

A simple planar monopole UWB slot antenna with dual independently and reconfigurable band‐notched characteristics

An extremely simple and compact planar monopole ultrawideband (UWB) slot antenna with dual band‐notched characteristics is proposed. The antenna is composed of a circular radiation patch, a microstrip‐fed line, and a partial ground. By etching an arc‐shaped slot on the radiation patch and a C‐like slot on the feed line, dual notched frequency bands at 3.3–3.7 GHz for WiMAX and 5.15–5.825 GHz for WLAN are achieved. And, the two notched bands can be adjusted independently by varying the length of the slots. Moreover, the band‐notched characteristics can be reconfigurable by shorting the corresponding slots. So, the antenna is capable of operating in one of multiple modes which makes it an excellent candidate for UWB applications. Meanwhile, experimental results indicate that the antenna has an available impendence bandwidth from 2.9 to 11 GHz which covers the UWB frequency band, and nearly omnidirectional patterns, stable gains, small group delay in operating band except rejected bands. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:706–712, 2014.     

A vertex‐fed hexa‐band frequency reconfigurable antenna for wireless applications

Present article embodies the design and analysis of an octagonal shaped split ring resonator based multiband antenna fed at vertex for wireless applications with frequency‐band reconfigurable characteristics. The proposed antenna is printed on FR4 substrate with electrical dimension of 0.4884 λ × 0.4329 λ × 0.0178 λ (44 × 39 × 1.6 mm³), at lower frequency of 3.33 GHz. The antenna consists of SRR based vertex fed octagonal ring as the radiation element and switchable reclined L‐shaped slotted ground plane. Antenna achieves six bands for wireless standards viz: upper WLAN (5.0/5.8 GHz), lower WiMAX (3.3 GHz), super extended C‐band (6.6 GHz), middle X band (9.9 GHz—for space communication), and lower K_U band (15.9 GHz—for satellite communication systems operating band). Stable radiation patterns are observed for the operating bands with low cross polarization. The proposed design achieves hexa band characteristics during switching ON state of PIN diode located at reclined L‐shaped slot in the ground plane. Experimental characteristic of antenna shows close agreement with those obtained by simulation of the proposed antenna.     

Circularly polarized D‐shaped slot antenna for wireless applications

A multiband circularly polarized slot antenna for wireless local area networks (WLAN) and worldwide interoperability for microwave access (WiMAX) applications is designed, studied, and fabricated. Using modified ground plane structure, circular polarized characteristics are realized. An open rectangular loop is introduced on the ground plane to generate orthogonal modes at middle resonance frequency. At higher resonance frequency to improve axial ratio bandwidth, a D‐shaped radiator is used. Thus, the cooperation of modified ground plane, open loop resonator, and D‐shaped radiator improves performance of the antenna at all the required bands. The proposed microstrip antenna generates separate impedance bandwidths to cover frequency bands of WLAN and WiMAX applications. The realized antenna is relatively small in size 40 × 54 mm² or 0.26_ × 0.36_ where _ is the free‐space wavelength at the desired first resonant frequency 2.0 GHz and operates over frequency ranges 26% (2.0‐2.6 GHz), 8.9% (3.21‐3.51 GHz), and 50.6% (3.8‐6.38 GHz). In addition, the antenna exhibits 5% (2.32‐2.44 GHz), 5.8% (3.3‐3.5 GHz), and 5.2% (5.61‐5.91 GHz) Circular Polarization bandwidth, making it suitable for WLAN and WiMAX applications.     

Compact meander T‐shaped monopole antenna for dual‐band WLAN applications

A compact coplanar waveguide‐feed monopole antenna with dual‐band characteristics is proposed in this article. The proposed antenna mainly consists of meander T‐shaped monopole and small ground plane embedded with a pair of L‐shaped couple slots and two pairs of I‐shaped notched slots symmetrically. By elongating the meander T‐shaped arms and carefully selecting the positions and lengths of L‐shaped slot and I‐shaped slot, the antenna excites four resonant frequencies at 2.42, 2.52, 4.75, and 5.54 GHz which are formed into two wide bands to cover all the 2.4/5.2/5.8 GHz wireless local area network (WLAN) operating bands, and is with miniaturization structure. Moreover, the antenna can provide nearly dipole‐like radiation patterns and good gains across the dual operating bands. These results prove that the proposed dual‐band antenna is very suitable for WLAN applications. © 2012 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2013.     

A miniaturized printed monopole antenna for 5.2‐5.8 GHz WLAN applications

In this article, a new design of a compact printed rectangular antenna for wireless local area network (WLAN) applications in 802.11a is investigated. The defected ground structure (DGS) technique is successfully used to reduce the ground plane by cutting a large slot to achieve significant miniaturization. The ground plane structure consists of inverted ‘L’ shape. The rectangular radiating element has a size of 6 × 5 mm² and is connected to a microstrip transmission feed line. The simulated and measured resonance frequency of the single‐band antenna is approximately 5.8 GHz and may cover an impedance bandwidth of 1 GHz for the measurement and 1.65 GHz for the simulation. The simulated and the measured data are in good agreement. The proposed antenna is very compact (10 × 6 mm²) and its impedance bandwidth is suitable for the 5.2‐5.8 GHz WLAN communication systems.     

Design of a microstrip fed printed monopole antenna for bluetooth and UWB applications with WLAN notch band characteristics

In this article, a microstrip fed printed dual band antenna for Bluetooth (2.4–2.484 GHz) and ultra‐wide band (UWB; 3.1–10.6 GHz) applications with wireless local area network (WLAN; 5.15–5.825 GHZ) band‐notch characteristics is proposed. The desired dual band characteristic is obtained by using a spanner shape monopole with rectangular strip radiating patch, whereas the band‐notch characteristics is created by a mushroom‐like structure. The Bluetooth and notch bands can easily be controlled by the geometric parameters of the rectangular strip and mushroom structure, respectively. The proposed antenna has been designed, fabricated, and tested. It is found that the proposed antenna yields both the Bluetooth and UWB performance in the frequency regions of 2.438 to 2.495 GHz and 3.10 to 10.66 GHz, respectively for |S₁₁| ≤ ?10 dB with an excellent rejection band of 5.14 to 5.823 GHz to prevent WLAN signals. The experimental results provide good agreement with simulated ones. Surface current distributions are used to analyze the effects of the rectangular strip and mushroom. The designed antenna exhibits nearly omnidirectional radiation patterns, stable gain along with almost constant group delay over the desired bands. Hence, the proposed antenna is expected to be suitable for both Bluetooth and UWB applications removing the WLAN band. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:66–74, 2015.     

Annular‐ring slot antenna designs with circular polarization radiation

The design of a microstrip‐fed annular‐ring slot antenna (ARSA) with circular polarization (CP) radiation is initially studied. To obtain CP radiation with broad 3‐dB axial ratio (AR) bandwidth that can cover the WiMAX 2.3 GHz (2305–2320 MHz, 2345–2360 MHz) and WLAN 2.4 GHz (2400–2480 MHz) bands, a novel technique of extending an inverted L‐shaped slot from the bottom section of the annular‐ring is proposed. To suppress the harmonic modes induced by the CP ARSA, the technique of integrating a defected ground structure into the annular‐ring slot is further introduced. From the measured results, 10‐dB impedance bandwidth and 3‐dB AR bandwidth of 44.86 and 9.68% were achieved by the proposed harmonic suppressed CP ARSA. Furthermore, average gain and radiation efficiency of ～4.7 dBic and 71%, respectively, were also exhibited across the bands of interest. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:337–345, 2015.     

Dual‐band reconfigurable circularly polarized monopole antenna

A microstrip antenna with dual‐band reconfigurable circular polarization (CP) characteristics in Wireless Local Area Network (WLAN) and Worldwide Interoperability for Microwave Access (WiMAX) bands is presented in this article. The proposed antenna has a symmetrical U‐shaped slot with PIN diodes on the ground plane. The slotted ground generates a resonant mode for broad impedance‐band width, and excites contrary CP state at 2.45 GHz for WLAN and 3.4 GHz for WiMAX, respectively. Because switching the states of PIN diodes on the slot can redirect the current path, the CP state of the proposed antenna can be simply switched between the right‐handed CP and left‐handed CP. The proposed antenna has a low profile and a simple structure. Measured results of the fabricated antenna prototype are carried out to verify the simulation analysis. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:109–114, 2015.     

Circularly polarized planar monopole antenna for ultrawideband applications

A broadband circularly polarized (CP) planar monopole antenna is proposed here for ultrawideband (UWB) communication. The antenna is composed of a modified annular ring patch fed by a tapered microstrip line and a rectangular semiground plane on the opposite side of the substrate. Capability of generating wide axial ratio bandwidth (ARBW) is another feature of the proposed antenna. Wide ARBW is achieved by introducing a rectangular slot and a stub in the ground plane. The CP antenna has an impressive ARBW of 5.52 GHz (81.42%, 4.02‐9.54 GHz) within the UWB frequency range (3.1‐10.6 GHz). Measured 10‐dB return loss bandwidth of the proposed antenna is 120.86% centered at 7.48 GHz (2.96‐12 GHz). The proposed antenna is well used for wireless local area network (5.2 and 5.8 GHz), Worldwide Interoperability for Microwave Access (5.5 GHz), and other wireless systems in C band as well as CP‐UWB antenna communication.     

Compact frequency reconfigurable triple band notched monopole antenna for ultrawideband applications

A compact ultra‐wideband (UWB) reconfigurable microstrip fed monopole antenna having size of 0.22 λ₀ × 0.28 λ₀ × 0.005 λ₀ with switchable frequency bands is presented. Triple band notched characteristics are achieved by inserting two stubs at top of radiator and one slot in between the radiator and microstrip feed line. Proposed antenna achieves reconfigurability with three PIN diodes at strategic positions to obtain eight different operational modes. In one of the operational modes, antenna operates in the entire UWB (3‐14 GHz) with fractional bandwidth of 127.5%. Two stubs are used to notch two frequency bands worldwide interoperability for microwave access (3.3‐3.6 GHz/WiMAX) and C‐band (3.7‐4.2 GHz). T‐shaped slot is also inserted to notch wireless local area network (5.725‐5.825 GHz/WLAN) frequency band. Proper biasing of PIN diodes is done by using suitable chip inductors and capacitors. Proposed antenna exhibits stable radiation patterns with average gain of around 3 dBi. Simulation and measurement results are in good agreement. Proposed antenna is suitable for on‐demand band rejection of parasitic bands coexisting in UWB.     

Dielectric resonator array antenna for triple band WLAN applications with enhanced gain

An H‐shaped dielectric resonator array antenna is presented for wideband applications. The proposed antenna is excited by slot feed mechanism and investigated experimentally. The antenna covers the frequency ranges from 1.41 to 2.59 GHz, and 4.73 to 6.06 GHz with the corresponding impedance bandwidth of 59% and 24.65%, respectively. The simulation results fulfill the bandwidth requirements of IEEE 802.11a/b/g (2.4‐2.484 GHz/5.15‐5.35 GHz/5.725‐5.825 GHz) for Wireless local area network (WLAN) applications. The proposed antenna has simple structure, easy to fabricate and its measured radiation pattern shows a reliable performance in the desired operating bands.     

Asymmetric circularly polarized open‐slot antenna

A circularly polarized printed antenna using an asymmetric open‐slot is designed in this paper. The presented antenna consists of conducting ground plane with open wide‐slot, fed electromagnetically by a microstrip feedline. The slot and feedline are positioned at the edge of the ground plane and substrate, hence making the antenna asymmetric. The measured results show that the |S₁₁| < ?10 dB impedance bandwidth is 125% (3.2‐14 GHz) and the broadband axial ratio bandwidth is 61% (3.2‐6 GHz). The antenna is very simple and has a small size of 25 mm × 25 mm, making it attractive for compact wireless WLAN, ISM, WiMAX, and C‐band applications.     

A wideband circularly polarized slot antenna with antipodal strips for WLAN and C‐band applications

A single‐fed circularly polarized square shaped wide slot antenna with modified ground plane and microstrip feed has been presented. The field in the slot is perturbed by introducing an antipodal strips section attached with a microstrip line to produce circular polarization in a wide band of frequencies. The antipodal strip section consists of a group of four strips of unequal length and separation. The presence of asymmetric perturbations in the slot is mainly responsible for exciting two orthogonal modes in the slot having equal magnitude and 90° phase difference which results in circular polarization. A wide bandwidth of 3.3 GHz (4.4 GHz‐7.7 GHz) has been achieved for an axial ratio value AR < 3 dB with the minimum axial ratio value being 0.3 dB. The impedance bandwidth for |S₁₁| < ?10 dB ranges from 4.3 GHz to 8 GHz, and therefore covers most of the C‐band communication systems. The antenna exhibits stable radiation patterns throughout the circular polarization bandwidth with a gain around 6 dBi in entire operational bandwidth. A prototype of antenna was fabricated and measured. The antenna has a planar size 0.40λ₀ × 0.40λ₀ and thickness of 0.02λ₀ where λ₀ is the wavelength in free space at the lowest frequency. With its compact size and low profile, the antenna is a favorable choice for WLAN (5.15‐5.85 GHz) and a wide variety of C‐band wireless applications.     

Design,analysis, and measurement of a new dual‐band compact hybrid resonator antenna

A new dual‐band compact hybrid resonator antenna is proposed in this article. The analysis is based on electric‐field and magnetic‐field integral equations. In the proposed design, the structure uses a combination of a thin circular disk dielectric resonator (DR) and a microstrip‐fed dog‐bone slot. This dog‐bone slot works as a half‐wavelength radiator and as a feed circuit for the DR. By optimizing the structure's parameters, the hybrid structure allows not only the DR to resonate at one frequency band but also the dog‐bone slot to resonate at the other one with the required frequency separation. Based on the above design concept, an antenna prototype for wireless communication applications centered at 1.9 and 2.45 GHz is successfully designed, fabricated, and tested. © 2006 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2006.     

Substrate integrated waveguide dual‐frequency dual‐sense circularly polarized cavity‐backed slot antenna

A novel design of dual‐frequency dual‐sense circularly polarized (CP) substrate integrated waveguide (SIW) cavity‐backed slot antenna is presented for dual‐band wireless communication systems. The proposed antenna consists of square SIW cavity, asymmetrical bow‐tie‐shaped cross slot and probe feed. Due to use of asymmetrical bow‐tie‐shaped cross slot, circularly polarized wave radiates at two different frequencies with opposite sense of polarizations. The RHCP radiation occurs at (10.45‐10.54) GHz (Lower band) and LHCP occurs at (11.26‐11.34) GHz (Upper band). Moreover, in each band, sense of polarization can be change by changing the feed position. The front to back radiation ratio (FTBRR) is more than 10.5 dB and cross polarization level is lower than ?20 dB in both the bands.     

Design of a compact triple band antenna with independent frequency tuning for MIMO applications

In this article, a planar, low profile microstrip line‐fed triple band multiple input multiple output (MIMO) antenna is presented for WiMax (2.5/3.5/5.5 GHz)/WLAN (2.4/3.6/5.8 GHz) applications simultaneously. The single element of the MIMO antenna consists of (i) a rectangular split ring resonator (SRR), (ii) a stepped impedance resonator (SIR) inside the SRR and (iii) a slot on the SIR. Each of the resonators generates its own individual band and each band is independently tunable. The antenna exhibits three operating bands at 2.35‐2.85 GHz, 3.25‐3.90 GHz and 5.45‐5.65 GHz. Four antenna elements are used to design the proposed MIMO antenna. The simulated results are observed and reported in terms of S‐parameters, gain, radiation patterns, envelope correlation coefficient (ECC), diversity gain (DG), channel capacity loss (CCL) and total active reflection coefficient. ECC and CCL are within the acceptable range defined for 4G and 5G application standards. To validate the simulation results a prototype structure is fabricated and the measured results are compared with those obtained from the simulation.     

Design and analysis of slot antenna with band notch function

In this article, the design, simulation, and construction of a novel wide rectangular slot antenna fed by a 50 Ω coplanar waveguide (CPW) are presented and investigated for multifunctional communication systems. The physical dimension of the antenna is 29 mm (length) × 32 mm (width) × 1.6 mm (thickness). Detailed simulations and experimental investigations are performed to understand its behavior and to optimize for 2.4 GHz wireless local area network (WLAN) and ultra wideband (UWB) operations. The proposed slot antenna is etched on an FR4 substrate with a thickness of 1.6 mm and relative permittivity of 4.4. To improve the impedance matching, a stepped stub structure with CPW feed technique is used. According to the measured results, the proposed antenna has a large bandwidth from 2.1 to 11.6 GHz for voltage standing wave ratio (VSWR) less than 2, totally satisfying the requirement of 2.4 GHz WLAN and UWB systems, while providing the required band notch function from 5.1 to 5.9 GHz. The study of time domain characteristics and surface current distributions also indicate the band‐notched function of the antenna. The radiation patterns display nearly omnidirectional performance and the antenna gain is stable except for the rejected frequency band (5.1–5.9 GHz). Moreover, group delays are within 1.5 ns except for the notch‐band. It is observed that the simulated and experimental results have good agreement with each other. © 2012 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2012.