Influence of Ammonium Pentaborate (APB) on the Performance of Urea Formaldehyde (UF) Adhesives for Plywood

Ammonium pentaborate (APB) was used to modify urea formaldehyde (UF) resins, in which the formaldehyde to urea molar ratio was set at 1.80, 1.50, 1.25, and 1.05. Some specific properties, including gel time, free formaldehyde content in UF, bond strength, and formaldehyde emission levels from plywood were evaluated. The result showed that APB increased the gel time length, but also decreased free formaldehyde content and emission levels, which was reduced mostly by 79.0% and 81.4%, respectively. The result of bond strength indicated that APB was proper to modify high F/U molar ratio of UF resin regardless of the loading level, but a recommended loading level should be considered to relevantly lower the F/U molar ratio of UF. The suggested loading level of APB to UF is 8.0% to 6.0%, 6.0%, and 4.0% to UF resin with F/U molar ratio of 1.8, 1.5, and 1.25 separately.     

Dynamic mechanical analysis of urea formaldehyde resin modified by ammonium pentaborate as wood adhesive

Urea formaldehyde (UF) resins with varied molar ratio of formaldehyde (F) to urea (U), modified by ammonium pentaborate (APB) at different loading level, was analyzed by dynamic mechanical analysis (DMA) and evaluated via bonding properties of its glued plywood. The result indicated that a higher loading of APB made a slower gelling and improved the ΔE′ (the difference of storage modulus) of UF resin with F/U molar ratio of 1.8. Hexamethylenetetramine, generated from the ammonium ion in APB and formaldehyde in UF resin and characterized by the covalent bond connections, was considered as the main reason to improve the rigidity of the cured UF resin system. The bond strength result confirmed the DMA analysis that the addition of APB improved bonding performance of UF resin with higher F/U molar ratio such as 1.8. A specific recommendation loading level of APB was made to modify UF resins, of which 6.0 to 8.0% APB should be used to modify UF resin with F/U molar ratio of 1.8, then 6% and 4% loading level of APB to UF resin with F/U molar ratio of 1.50 and 1.25, respectively. Finally, APB was n'ot suggested to modify UF resin at F/U molar ratio less than 1.20. POLYM. COMPOS., 37:2404–2410, 2016. © 2015 Society of Plastics Engineers     

环保型脲醛树脂胶粘剂的制备研究

脲醛树脂是广泛用于木材工业中一种重要的胶粘剂,影响脲醛树脂甲醛含量的因素有多个方面,为寻求合适的工艺条件以提高脲醛树脂胶粘剂的综合性能,通过改变尿素与甲醛的摩尔质量比及控制反应时间等途径优化了环保型脲醛树脂胶粘剂的合成方法.实验结果表明:在U/F=1:2.0,pH达到5～6时反应40分钟,此时的胶粘剂甲醛含量与粘性的综合情况最佳.     

尤戎(Uron)树脂及其用法对脲醛树脂性能的影响

以不同工艺制备了三种含尤戎结构的脲醛树脂(Uron树脂),通过其与普通脲醛树脂的混合制得多种混合脲醛树脂。研究了Uron树脂及其使用方法对降低脲醛树脂胶粘剂游离甲醛含量及胶接胶合板甲醛释放量的作用与效果。结果表明:1)三种不同摩尔比的Uron树脂对脲醛树脂游离甲醛含量及胶接胶合板甲醛释放量都有明显的降低作用,游离甲醛含量最多可降低43％,甲醛释放量最多可降低61％;2)Uron树脂的添加量在10％-20％时对胶合强度的提高有利,强度最大可提高29％;3)低摩尔比Uron树脂对脲醛树脂的改性效果优于高摩尔比Uron树脂。     

Reactivity,chemical structure,and molecular mobility of urea–formaldehyde adhesives synthesized under different conditions using FTIR and solid‐state 13C CP/MAS NMR spectroscopy

This study was conducted to investigate the effects of reaction pH condition and hardener type on the reactivity, chemical structure, and molecular mobility of urea–formaldehyde (UF) resins. Three different reaction pH conditions, such as alkaline (7.5), weak acid (4.5), and strong acid (1.0), were used to synthesize UF resins, which were cured by adding four different hardeners (ammonium chloride, ammonium sulfate, ammonium citrate, and zinc nitrate) to measure gel time as the reactivity. FTIR and ¹³C‐NMR spectroscopies were used to study the chemical structure of the resin prepared under three different reaction pH conditions. The gel time of UF resins decreased with an increase in the amount of ammonium chloride, ammonium sulfate, and ammonium citrate added in the resins, whereas the gel time increased when zinc nitrate was added. Both FTIR and ¹³C‐NMR spectroscopies showed that the strong reaction pH condition produced uronic structures in UF resin, whereas both alkaline and weak‐acid conditions produced quite similar chemical species in the resins. The proton rotating‐frame spin–lattice relaxation time (T_1ρH) decreased with a decrease in the reaction pH of UF resin. This result indicates that the molecular mobility of UF resin increases with a decrease in the reaction pH used during its synthesis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2677–2687, 2003     

低甲醛释放量人造板用改性脲醛树脂制备及应用研究

为了降低脲醛树脂的游离甲醛含量及其胶接制品的甲醛释放量,本研究在脲醛树脂合成过程中加入改性剂代替部分甲醛,通过尿素-甲醛-改性剂发生共缩聚反应,合成了改性脲醛树脂。研究了改性剂取代甲醛的摩尔比对改性脲醛树脂固化速度、游离甲醛含量的影响,以及在不同的热压条件下,对胶接胶合板的胶合强度和甲醛释放量的影响。研究结果表明,改性剂的加入不仅能有效降低改性脲醛树脂的游离甲醛含量及其胶合板的甲醛释放量,还能提高胶合板的胶合强度和耐水性。     

低游离甲醛脲醛树脂合成工艺研究

脲醛(UF)树脂是一种广泛应用于木材加工业的胶黏剂,文章采用碱-酸-碱合成工艺,探讨了甲醛与尿素的摩尔比、pH、反应温度及尿素加料方式等因素对UF树脂黏度及游离甲醛含量的影响,发展了制备低毒(游离甲醛含量0.13%)UF树脂的新工艺,并用IR对UF树脂进行了确证。     

A comparison between lignin modified by ionic liquids and glyoxalated lignin as modifiers of urea-formaldehyde resin

The aim of this research was to compare the influence of modified lignin by ionic liquid (IL) on the physical and mechanical properties of wood-based panels bonded with urea-formaldehyde (UF) resin with the effect of glyoxalated lignin (GL) on UF properties. For this purpose, soda bagasse lignin was respectively modified by 1-ethyl-3-methylimidazolium acetate ([Emim][OAc]) IL and glyoxal and then the various content of modified lignins (10, 15, and 20%) were added at pH=7 during the UF resin synthesis instead of the second urea . The changes in the structure and thermal properties of lignin, after and before modification with glyoxal and IL, were analyzed by Fourier transform infrared spectrometry (FTIR) and differential scanning calorimetry (DSC). The physicochemical properties of the prepared resins as well as the water absorption, shear strength, and formaldehyde emission of the plywood panels made with these adhesives were measured according to standard methods. According to the FTIR spectra, the content of C=O bond increased in GL while in the IL-treated lignin the content of C–N bond markedly increased. DSC analysis indicated that lignin modified by IL had lower glass transition temperature (T_g) value compared to those modified with glyoxal and unmodified lignin, respectively. The UF resins containing IL-treated lignin exhibit a faster gel time compared to those prepared with GL. Equally, the plywood panels prepared with an IL had lower formaldehyde emission and higher mechanical strength compared to those made from UF resin containing GL. There were no significant differences in dimensional stability of the panels bonded with UFs modified with GL and those with IL-modified lignin.     

木质素在脲醛树脂胶粘剂中的应用

为解决脲醛树脂(UF)胶粘剂中游离甲醛含量偏高等问题,首先确定了n[甲醛(F)]∶n[尿素(U)]的合适比例,然后以羟甲基化木质素作为UF的改性剂,制备木质素改性UF胶粘剂。研究了木质素的种类及用量对UF各项性能的影响。结果表明:UF中游离甲醛含量随n(F)∶n(U)比例增加而增大;在UF改性过程中,硝酸木质素对游离甲醛的捕捉能力优于硫酸木质素,当w(硝酸木质素)=30%(相对于尿素总质量而言)时,游离甲醛含量(0.126%)相对最低;木质素加入的同时还有助于提高改性UF胶粘剂的胶接强度和耐水性。     

环保型高剪切强度脲醛树脂胶黏剂的制备

采用碱-酸-碱合成工艺,分段控制温度,分批加入尿素,加PVA改性,制备脲醛树脂胶黏剂。研究了n(F)/n(U)、反应温度、反应时间和PVA加入量对胶液甲醛含量和试样剪切强度的影响。结果表明:当n(F)/n(U)为1.4:1,反应温度为95℃,反应时间为70min,PVA加入1.0%时,制备的胶黏剂游离甲醛的含量降至0.1%以下,试样的剪切强度可达3.0MPa以上。     

Reduction of Formaldehyde Emission from Particleboard by Phenolated Kraft Lignin

The aim of this study was the reduction of formaldehyde emission from particleboard by phenolated Kraft lignin. For this purpose, the lignin was extracted from black liquor and then modified by phenolation. During the urea formaldehyde (UF) resin synthesis different proportions of unmodified and phenolated Kraft lignins (10%, 15%, and 20%) were added at pH = 7 instead of the second urea. Physicochemical properties and structural changes of resins so prepared, as well as the internal bond (IB) strength and formaldehyde emission associated with the panels bonded with them were measured according to standard methods. The Fourier transform infrared (FTIR) analysis of lignin indicated that the content of O–H bonds increased in phenolated lignin while the aliphatic ethers C–O bonds decreased markedly in the modified lignin. Since both synthesis of UF resins and lignin phenolation are carried out under acid conditions, phenolation is an interesting way of modifying lignin for use in wood adhesive. The panels bonded with these resins showed significantly lower formaldehyde emission compared to commercial UF adhesives. The UF resin with 20% phenolated lignin exhibited less formaldehyde release without significant differences in internal bond strength and physicochemical properties compared to an unmodified UF resin. XRD analysis results indicated that addition of phenolated lignin decreased the crystallinity of the hardened UF resins.     

Urea–formaldehyde‐resin gel time as affected by the pH value,solid content,and catalyst

An experiment was conducted to investigate the effects of the resin solid content, catalyst content, and pH value obtained by the addition of two kinds of catalysts on the gel time of a urea–formaldehyde (UF) resin. Upon the addition of ammonium chloride, the pH value of the resin mixture decreased to 7 but not significantly further because of the limited free formaldehyde in the system. The pH values of the critical points, at which the resin‐curing rate dramatically increased and the gel time was reduced, were above 7 for both catalysts. To achieve the same gel time, the required pH value of the UF resin adjusted with ammonium chloride was higher than that of the resin modified by hydrochloric acid. This indicated that the main effects of ammonium chloride on the UF‐resin cure included both the release of hydrochloric acid and the catalysis of the reactants in the UF‐resin system. The gel time of the UF resin obviously decreased with increasing catalyst and resin solid contents and with decreasing pH. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1566–1569, 2007     

Synthesis,structure, and characterization of glyoxal‐urea‐formaldehyde cocondensed resins

To decrease the formaldehyde emission of urea‐formaldehyde (UF) bonded products at source, monomethylol urea (MMU) was chosen to react with glyoxal (G), a nonvolatile and nontoxic aldehyde, to prepare a novel glyoxal‐urea‐formaldehyde (GUF) cocondensed resin. The GUF resins were synthesized with different MMU/G molar ratios, and the basic properties were tested. The GUF resins were characterized by ultraviolet‐visible spectroscopy, Fourier transform infrared spectroscopy, carbon‐13 nuclear magnetic resonance spectroscopy and matrix assisted laser desorption ionization time of flight mass spectrometry (MALDI‐TOF‐MS). The results show that the synthesized GUF resins remain stable for at least 10 days at ambient temperature. Conjugated structures, and large amounts of ? OH, ? NH? , C? N, and C?O groups with different levels of substitution exist in the GUF resin. There are two repeating motives in the MALDI‐TOF‐MS spectrum of the GUF resin, one of 175 ±1 Da and a second one of 161 ± 1 Da. Moreover, the peaks due to the dehydration condensation reaction of MMU also appear in the spectra. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41009.     

多羟甲基苯酚改性脲醛树脂的研究

脲醛树脂(UF)是木材工业的主要胶种,为了提高UF的胶接性能和耐水性,同时实现低n(甲醛)∶n(尿素)比例UF中尿素的作用,采用自制的多羟甲基苯酚对UF进行改性,并通过胶合板的压制试验和差示扫描量热(DSC)法来研究改性UF的使用性能。结果表明:多羟甲基苯酚加入时间对UF诸多性能产生明显的影响;当质量分数为10%的多羟甲基苯酚在UF合成末期投入时,所得UF的综合性能相对最佳;与未改性UF胶粘剂压制的胶合板相比,由改性UF胶粘剂压制的胶合板具有相对较高的干强度(1.86 MPa)和湿强度(1.82 MPa),其甲醛释放量降低了30.8%。     

低毒脲醛树脂胶粘剂的研究进展

综述了低游甲醛脲醛胶粘剂的合成技术,对原料摩尔比、改性剂、缩聚工艺、甲醛捕捉剂等因素进行了讨论。     

NMR study of the stabilities of urea–formaldehyde resin components toward hydrolytic treatments

The solid residues of nine urea–formaldehyde (UF) resins after hydrolytic treatment at pH4 and 86°C for 20 h and the solid residues of one UF resin after eight different hydrolytic treatments were examined by ¹³C-CP–MAS NMR. The relative stability toward hydrolysis of each structural component in each UF resin was established for various hydrolytic conditions. In general, UF resins prepared from starting mixtures with a formal F/U molar ratio of 1.00 show a high degree of stability toward hydrolysis. Cross-linking methylene linkages in the UF resins show a higher susceptibility to hydrolytic treatments at pH 4 and 86°C than do linear methylene linkages. UF resins prepared with an F/U molar ratio of 2.00 are susceptible to hydrolysis at pH 4 and 86°C. Dimethylene ether linkages, methylols attached to tertiary amides, and poly(oxymethylene glycol) moieties are probably the main formaldehyde emitters in UF resin products. © 1994 John Wiley & Sons, Inc.     

Effects of formaldehyde to urea mole ratio on thermal curing behavior of urea–formaldehyde resin and properties of particleboard

As a part of abating the formaldehyde emission (FE) of urea–formaldehyde (UF) resin, this study was conducted to investigate the effects of formaldehyde to urea (F/U) mole ratio on thermal curing behavior of UF resins and properties of PB bonded with them. UF resins synthesized at different F/U mole ratios (i.e., 1.6, 1.4, 1.2, and 1.0) were used for the manufacture of PB. Thermal curing behavior of these UF resins was characterized using differential scanning calorimetry (DSC). As the F/U mole ratio decreases, the gel time, onset and peak temperatures, and heat of reaction (ΔH) increased, while the activation energy (E_a) and rate constant (k) were decreased. The amount of free formaldehyde of UF resin and FE of PB prepared decreased in parallel with decreasing the F/U mole ratio. The internal bond strength, thickness swelling, and water absorption of PB was slightly deteriorated with decreasing the F/U mole ratio of UF resins used. These results indicated that as the F/U mole ratio decreased, the FE of PB was greatly reduced at the expense of the reactivity of UF resin and slight deterioration of performance of PB prepared. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1787–1792, 2006     

Examination of selected synthesis parameters for wood adhesive‐type urea–formaldehyde resins by 13C NMR spectroscopy. III

The varying polymer structures of wood adhesive‐type urea–formaldehyde resins resulting from different formaldehyde/first urea (F/U₁) mole ratios used in the first step of resin manufacture were investigated using ¹³C. As the F/U₁ mole ratio decreased progressively from 2.40 to 2.10 and to 1.80, the viscosity increase due to polymerization during resin synthesis became faster and resulted in decreasing side‐chain branches and increasing free urea amide groups in the resin structure. The resultant UF resins, with the second urea added to an overall F/(U₁ + U₂) of 1.15, showed viscosity decreases when heated with stirring or allowed to stand at room temperature that were also characteristic with the F/U₁ mole ratios used in resin synthesis. The formaldehyde emission levels of particleboards bonded with the freshly made UF resins showed relatively small but similarly characteristic variations. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2800–2814, 2001     

Uron and uron–urea‐formaldehyde resins

The favored pH ranges for the formation of urons in urea‐formaldehyde (UF) resins preparation were determined, these being at pH's higher than 6 and lower than 4 at which the equilibrium urons ↔ N,N′‐dimethylol ureas are shifted in favor of the cyclic uron species. Shifting the pH slowly during the preparation from one favorable range to the other causes shift in the equilibrium and formation of a majority of methylol ureas species, whereas a rapid change in pH does not cause this to any great extent. UF resins in which uron constituted as much as 60% of the resin were prepared and the procedure to maximize the proportion of uron present at the end of the reaction is described. Uron was found to be present in these resins also as linked by methylene bridges to urea and other urons and also as methylol urons, the reactivity of the methylol group of this latter having been shown to be much lower than that of the same group in methylol ureas. Thermomechanical analysis (TMA) tests and tests on wood particleboard prepared with uron resins to which relatively small proportions of urea were added at the end of the reaction were capable of gelling and yielding bonds of considerable strength. Equally, mixing a uron‐rich resin with a low F/U molar ratio UF resin yielded resins of greater strength than a simple UF of corresponding molar ratio indicating that UF resins of lower formaldehyde emission with still acceptable strength could be prepared with these resins. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 277–289, 1999     

胶合板用脲醛树脂胶粘剂的纳米改性

以MMT(蒙脱土)或OMMT(有机蒙脱土)作为改性剂,两者分别在UF(脲醛树脂)合成的不同阶段(加成阶段、缩聚阶段和缩聚后期)中以同一投料比引入体系中,制备相应的改性UF胶粘剂。研究结果表明:当n(F):n(U)=1.2:1、w(MMT或OMMT)=2%(相对于尿素总质量而言)时,MMT和OMMT的引入,能使相应改性UF胶粘剂的某些性能(如黏度、固含量、胶接强度和固化时间等)增加、游离甲醛含量降低;OMMT的改性效果优于MMT,并且OMMT在加成阶段投入时降醛效果明显,在缩聚阶段投入时补强效果明显。