SIMULATION OF SUPERHEATED STEAM DRYING CONSIDERING INITIAL STEAM CONDENSATION

A heat and mass transfer model was proposed for the superheated steam drying, focusing on phenomena which occur during the initial stage of drying, i.e., condensation of superheated steam on material surfaces and subsequent shift from condensation to evaporation leading to the beginning of the actual drying (Reverse Process Model). Next, drying equations considering the reverse process were formulated for a shrinking/swelling infinite flat plate to calculate moisture content and temperature distributions in a material, changes in mass of a material with time, and a characteristic drying curve. Then, the influence of the initial thickness of a material and the heat transfer coefficient were investigated. In addition, calculation results were compared with experimental ones with regard to the change in mass of material with time and the characteristic drying curve, and good conformance was obtained for the initial stage of drying.     

DRYING OF SLICED RAW POTATOES IN SUPERHEATED STEAM AND HOT AIR

Drying experiments were conducted on raw potato slices, using atmospheric pressure superheated steam and hot air as drying media at 170 and 240°C. Mass changes of the material were continuously measured, the conditions of cross section near the surfaces were observed with an electron microscope, also color changes of their surface were measured during drying. The respective drying methods and temperature conditions were compared and it was found that, in the case of superheated steam drying, moisture content temporarily increases due to steam condensation in the initial stage of drying, therewith, as well as starch gelatinization rapidly develops. Meanwhile, in case of hot air drying, starch gelatinization occurs more slowly than with superheated steam drying and that non-gelatinized starch granules remain on the surface when drying was completed. Furthermore, surface color measurements showed that samples dried by superheated steam were more reddish than ones dried by hot air and the surfaces were more glossy, because no starch granules remain on the surface in case of superheated steam drying.     

DRYING OF SLICED RAW POTATOES IN SUPERHEATED STEAM AND HOT AIR

Drying experiments were conducted on raw potato slices, using atmospheric pressure superheated steam and hot air as drying media at 170 and 240°C. Mass changes of the material were continuously measured, the conditions of cross section near the surfaces were observed with an electron microscope, also color changes of their surface were measured during drying. The respective drying methods and temperature conditions were compared and it was found that, in the case of superheated steam drying, moisture content temporarily increases due to steam condensation in the initial stage of drying, therewith, as well as starch gelatinization rapidly develops. Meanwhile, in case of hot air drying, starch gelatinization occurs more slowly than with superheated steam drying and that non-gelatinized starch granules remain on the surface when drying was completed. Furthermore, surface color measurements showed that samples dried by superheated steam were more reddish than ones dried by hot air and the surfaces were more glossy, because no starch granules remain on the surface in case of superheated steam drying.     

SUPERHEATED STEAM IMPINGEMENT DRYING OF TORTILLA CHIPS

ABSTRACT

Low-fat snack products are the driving forces for the drying of tortilla chips before frying. Super-heated steam impingement drying of foods has the advantage of improved energy efficiency and product quality. The temperature profile, drying curves, and the physical properties (shrinkage, crispiness, starch gelatinization and microstructure) of tortilla chips dried at different superheated steam temperatures and heat transfer coefficients were measured. Results indicated that the steam temperature had a greater effect on the drying curve than the heat transfer coefficient within the range of study. The microstructure of the samples after steam drying showed that higher steam temperature resulted in more pores and coarser appearance. The modulus of deformation and the shrinkage of tortilla chips correlated with moisture content. A higher steam temperature caused less shrinkage and a higher modulus of deformation. The pasting properties showed that samples dried under a higher steam temperature and a higher heat transfer coefficient gelatinized less during drying and had a higher ability to absorb water. Comparison of the superheated steam drying and air drying revealed that at elevated temperatures the superheated steam provided higher drying rates. Furthermore, there was a less starch gelatinization associated with air drying compared to superheated steam drying.     

SUPERHEATED STEAM IMPINGEMENT DRYING OF TORTILLA CHIPS

Low-fat snack products are the driving forces for the drying of tortilla chips before frying. Super-heated steam impingement drying of foods has the advantage of improved energy efficiency and product quality. The temperature profile, drying curves, and the physical properties (shrinkage, crispiness, starch gelatinization and microstructure) of tortilla chips dried at different superheated steam temperatures and heat transfer coefficients were measured. Results indicated that the steam temperature had a greater effect on the drying curve than the heat transfer coefficient within the range of study. The microstructure of the samples after steam drying showed that higher steam temperature resulted in more pores and coarser appearance. The modulus of deformation and the shrinkage of tortilla chips correlated with moisture content. A higher steam temperature caused less shrinkage and a higher modulus of deformation. The pasting properties showed that samples dried under a higher steam temperature and a higher heat transfer coefficient gelatinized less during drying and had a higher ability to absorb water. Comparison of the superheated steam drying and air drying revealed that at elevated temperatures the superheated steam provided higher drying rates. Furthermore, there was a less starch gelatinization associated with air drying compared to superheated steam drying.     

DRYING WITH SUPERHEATED STEAM

The principle of drying with superheated steam is known for a long time already, and different designs have been worked out and partly realised. The principle of the steam drying described in this paper starts with superheated steam that is blown on to the products to be dried. The superheated steam transfers its sensible heat to the product and the water to be evaporated. The superheated steam acts both as heat source and as drying medium to take away the evaporated water. The majority of the superheated steam has to be recirculated and reheated. The excess steam from this process, corresponding to the evaporated water, can be used elsewhere in the process or plant, thus making an efficient energy recovery possible. Possible emissions from the drying process can be effectively removed by condensation. Drying by means of superheated steam impingement is one of the possible designs that are in progress now for the paper industry. Work is going on with respect to this type of drying for other materials, especially foodstuffs. At present experimental research at the laboratory steam dryer of TNO-MEP is carried out for vegetables, fries, herbs, cacao nuts, wheat, flour, etc. Besides the energy savings and environmental benefits, the oxygen free steam atmosphere and the higher product temperatures in the dryer appear to have positive effects on the product qualities. For foodstuffs combinations of steam drying with blanching, pasteurisation, sterilisation, etc. are possible and make the steam drying very attractive for food producers. Modelling of the processes in foodstuffs during steam drying is established, both on macro and micro scale. In this paper examples and results of research on steam drying for specific products will be presented.     

OPTIMUM OPERATING CONDITIONS IN DRYING FOODSTUFFS WITH SUPERHEATED STEAM

It is inferred from experimental data that in drying foodstuffs with superheated steam, the initial drying rate has a direct effect on the rate at which the overall drying takes place. That is, the faster the initial drying rate, the shorter the overall drying time. This criterion is very convenient because at the beginning, water moistens the sample external surface so evaporation does not depend on internal sample characteristics, but only on external convective heat and mass transfer rates. Mass and energy balance equations are solved and the result converted into a general initial drying rate equation, in which all dryer characteristics are grouped into one dimensionless parameter. The initial drying rate equation is mathematically maximized and the optimum working conditions determined. The result shows that initial drying rate always increase with increases of either the superheated steam temperature or velocity, but once these two variables are fixed, there exists at least one “optimum” pressure at which the initial drying rate is a maximum. Finally, the initial drying rate and optimum condition equations are applied to three model dryers, a dryer for a flat sheet, a fixed bed dryer and a rotary dryer. In each case, numeric values are computed and plotted as drying rate versus pressure curves, in which the optimum drying rate is also included. Also presented is a chart to compare the optimum pressures as functions of temperature and steam velocity for the three dryers.     

STEAM DRYING OF WOOD CHIPS IN PNEUMATIC CONVEYING DRYERS

A model for a pneumatic conveying dryer is presented. Although the main emphasis is put on superheated steam drying of wood chips, it can be used for other porous materials as well

The model includes a comprehensive two-dimensional model for the drying of single wood chips which accounts for the main physical mechanisms occurring in wood during drying. The external drying conditions in a pneumatic conveying dryer were calculated by applying the mass, heat and momentum equations for each incremental step in dryer length. A plug flow assumption was made for the dryer model and the single particle and dryer models were solved in an iterative manner. The non-spherical nature of wood chips were accounted for by measuring the drag and heat transfer coefficients

Model calculations illustrate the complex interactions between steam, particles and walls which occur in a flash dryer. The drying rate varies in a very complex manner through the dryer. The internal resistance to mass transfer becomes very important in The drying of less permeable wood species such as spruce. Two effects were observed as the particle size was increased: firstly the heat transfer rate decreased, and secondly the residence time increased. To some extent, these effects compensate for each other, however, the net result is that larger chips have a higher final moisture content.     

Improvement of a mathematical model for low-pressure superheated steam drying of a biomaterial

Although there currently are a number of works reporting experimental study of low-pressure superheated steam drying (LPSSD), which has proved to be an attractive alternative to drying heat-sensitive biomaterials, there are a very few works reporting the development of a mathematical model to predict the evolutions of product moisture content and temperature during LPSSD. Moreover, the predictions of those few developed models are still not satisfactory because, most of the time, the models do not include the effect of initial steam condensation; the use of mass transfer boundary condition is, in some cases, also not quite realistic. The aim of the present study was thus to develop a more realistic liquid diffusion based model to simulate the transport of heat and mass within a product undergoing LPSSD. The effect of initial steam condensation, in terms of film condensation, was included and a more realistic mass transfer boundary condition, in terms of the vapor pressure gradient and the physical condition at the drying surface, was applied in the newly developed model. The effect of the product shrinkage was also included directly in the model. The predictability of the model was tested against the available experimental data. The model with initial steam condensation was found to be able to predict the center temperature and average moisture content of the product undergoing LPSSD very well. However, at higher temperatures and lower pressures the product core temperature was still under predicted.     

ANALYSIS OF TRANSPORT PHENOMENA DURING THE CONVECTIVE DRYING IN SUPERHEATED STEAM

This work focused on high-temperature convective drying (superheated steam drying). The process has been investigated both experimentally and numerically. The experimental analysis was carried out in an aerodynamic return-flow wind-tunnel, with very small cylinders of cellular concrete. For the local analysis, the samples were fitted with thermocouples and pressure sensors. The mean moisture content of the cylinders was measured by simple weighing while the temperature and pressure readings were being taken. Global and. local analysis of heat and mass transfer in small cylinders in superheated steam were carried out. The systematical study for several sizes and aerothermal conditions show a similar behavior for moisture content, pressure and temperature values. A numerical model for high temperature drying, using the finite elements method, in a 2-D configuration, was implemented and validated.     

STEAM DRYING OF WOOD CHIPS IN PNEUMATIC CONVEYING DRYERS

ABSTRACT

A model for a pneumatic conveying dryer is presented. Although the main emphasis is put on superheated steam drying of wood chips, it can be used for other porous materials as well

The model includes a comprehensive two-dimensional model for the drying of single wood chips which accounts for the main physical mechanisms occurring in wood during drying. The external drying conditions in a pneumatic conveying dryer were calculated by applying the mass, heat and momentum equations for each incremental step in dryer length. A plug flow assumption was made for the dryer model and the single particle and dryer models were solved in an iterative manner. The non-spherical nature of wood chips were accounted for by measuring the drag and heat transfer coefficients

Model calculations illustrate the complex interactions between steam, particles and walls which occur in a flash dryer. The drying rate varies in a very complex manner through the dryer. The internal resistance to mass transfer becomes very important in The drying of less permeable wood species such as spruce. Two effects were observed as the particle size was increased: firstly the heat transfer rate decreased, and secondly the residence time increased. To some extent, these effects compensate for each other, however, the net result is that larger chips have a higher final moisture content.     

FLASH DRYING OF FISH MEALS WITH SUPERHEATED STEAM: ISOTHERMAL PROCESS

The work considers the application of the flash drying to the moisture removal of fishmeal using superheated steam as transport medium. Heat, momentum and mass transfer equations were applied and an algorithm based on these equations was developed and solved. The model was validated using experimental data obtained in a pilot pneumatic dryer ( total length 60 m) provided with a steam jacket to maintain the superheated steam at a constant temperature. The drying time was less than 10 s to decrease the fish meals moisture content from 53.5% to 28% d.b. and in a second pass by the dryer the moisture down to 16.9% using superheated steam at It 1 ° C and 130 ° C in the jacket. The computational results are in agreement with the experimental data.     

ANALYSIS OF TRANSPORT PHENOMENA DURING THE CONVECTIVE DRYING IN SUPERHEATED STEAM

Abstract

This work focused on high-temperature convective drying (superheated steam drying). The process has been investigated both experimentally and numerically. The experimental analysis was carried out in an aerodynamic return-flow wind-tunnel, with very small cylinders of cellular concrete. For the local analysis, the samples were fitted with thermocouples and pressure sensors. The mean moisture content of the cylinders was measured by simple weighing while the temperature and pressure readings were being taken. Global and. local analysis of heat and mass transfer in small cylinders in superheated steam were carried out. The systematical study for several sizes and aerothermal conditions show a similar behavior for moisture content, pressure and temperature values. A numerical model for high temperature drying, using the finite elements method, in a 2-D configuration, was implemented and validated.     

Some Considerations In Simulation Of Superheated Steam Drying Of Softwood Lumber

ABSTRACT

A mathematical model for high-temperature drying of softwood lumber with moist air has been modified and extended to simulate wood drying with superheated steam. In the simulation, differences between the two types of drying are considered, these include: external heat and mass transfer processes and calculation of equilibrium moisture content. The external mass transfer coefficient in the perheated steam drying was found to be much higher than that in the moist air drying, however, the heat ransfer coefficients for these two cases were of the same order. The predicted drying curves and wood temperatures from the superheated steam drying model were compared with experimental data and there was close agreement. Further studies will apply the model to development of commercial drying schedules for wood drying with superheated steam.     

SIMULATED DEHYDRATION OF WEDGE-SHAPED SPECIMENS IN TURBULENT FLOW OF SUPERHEATED STEAM AND AIR

Numerical methods were used to study the effectiveness of superheated steam, humid air and dry air as dehydrating media in turbulent flow for the drying of wedge-shaped specimens. The Couette flow assumption was used to formulate the coupled heat and mass transfer in the turbulent boundary layer. Superheated steam was found to have highest evaporation rates at free stream temperatures above the inversion point.     

SIMULATED DEHYDRATION OF WEDGE-SHAPED SPECIMENS IN TURBULENT FLOW OF SUPERHEATED STEAM AND AIR

Numerical methods were used to study the effectiveness of superheated steam, humid air and dry air as dehydrating media in turbulent flow for the drying of wedge-shaped specimens. The Couette flow assumption was used to formulate the coupled heat and mass transfer in the turbulent boundary layer. Superheated steam was found to have highest evaporation rates at free stream temperatures above the inversion point.     

FLASH DRYING OF FISH MEALS WITH SUPERHEATED STEAM: ISOTHERMAL PROCESS

ABSTRACT

The work considers the application of the flash drying to the moisture removal of fishmeal using superheated steam as transport medium. Heat, momentum and mass transfer equations were applied and an algorithm based on these equations was developed and solved. The model was validated using experimental data obtained in a pilot pneumatic dryer ( total length 60 m) provided with a steam jacket to maintain the superheated steam at a constant temperature. The drying time was less than 10 s to decrease the fish meals moisture content from 53.5% to 28% d.b. and in a second pass by the dryer the moisture down to 16.9% using superheated steam at It 1 ° C and 130 ° C in the jacket. The computational results are in agreement with the experimental data.     

COMBINED SUPERHEATED STEAM AND MICROWAVE DRYING OF SINTERED GLASS BEADS: DRYING RATE CURVES

A new drying method of combined superheated steam and microwave drying is being proposed. The drying rates of sintered glass beads in combined superheated steam and microwave drying are experimentally and theoretically investigated. Drying experiments have been carried out in a waveguide where a standing wave is formed to uniformly heat a small sample. Concerning drying rate curves in combined superheated steam and microwave drying, a distinct constant rate period has been observed. For the falling rate period, high drying rates have been observed. For both periods, the drying rates in combined superheated steam and microwave drying are higher than those in superheated steam alone. Also, in comparison with the results of combined nitrogen and microwave drying, the normalized drying rates in combined superheated steam and microwave drying are higher than those at less than the critical moisture content in combined nitrogen and microwave drying. Moreover, theoretical drying rates for the falling rate period (predicted by a modified receding evaporation front model) in combined superheated steam and microwave drying, are in good agreement with the observed drying rates. The combined superheated steam and microwave drying method can attain higher drying rates under mild external conditions.     

Modeling Superheated Steam Vacuum Drying of Wood

A two-dimensional mathematical model developed for vacuum-contact drying of wood was adapted to simulate superheated steam vacuum drying. The moisture and heat equations are based on the water potential concept whereas the pressure equation is formulated considering unsteady-state mass conservation of dry air. A drying test conducted on sugar maple sapwood in a laboratory vacuum kiln was used to infer the convective mass and heat transfer coefficients through a curve fitting technique. The average air velocity was 2.5 m s^-1 and the dry-bulb temperature varied between 60 and 66°C. The ambient pressure varied from 15 to 11 kPa. Simulation results indicate that heat and mass transfer coefficients are moisture content dependent. The simulated drying curve based on transfer coefficients calculated from boundary layer theory poorly fits experimental results. The functional relation for the relative permeability of wood to air is a key parameter in predicting the pressure evolution in wood in the course of drying. In the case of small vacuum kilns, radiant heat can contribute substantially to the total heat transfer to the evaporative surface at the early stages of drying. As for conventional drying, the air velocity could be reduced at the latter stage of drying with little or no change to the drying rate.     

Modeling Superheated Steam Vacuum Drying of Wood

Abstract

A two-dimensional mathematical model developed for vacuum-contact drying of wood was adapted to simulate superheated steam vacuum drying. The moisture and heat equations are based on the water potential concept whereas the pressure equation is formulated considering unsteady-state mass conservation of dry air. A drying test conducted on sugar maple sapwood in a laboratory vacuum kiln was used to infer the convective mass and heat transfer coefficients through a curve fitting technique. The average air velocity was 2.5 m s^?1 and the dry-bulb temperature varied between 60 and 66°C. The ambient pressure varied from 15 to 11 kPa. Simulation results indicate that heat and mass transfer coefficients are moisture content dependent. The simulated drying curve based on transfer coefficients calculated from boundary layer theory poorly fits experimental results. The functional relation for the relative permeability of wood to air is a key parameter in predicting the pressure evolution in wood in the course of drying. In the case of small vacuum kilns, radiant heat can contribute substantially to the total heat transfer to the evaporative surface at the early stages of drying. As for conventional drying, the air velocity could be reduced at the latter stage of drying with little or no change to the drying rate.