Soybean Drying by Two-Dimensional Spouted Bed

Urease activity, cracking, and breakage are important factors in considering the quality of raw soybean for feed meal industries. A two-dimensional spouted bed dryer was investigated to determine its capability for thermally inactivating the urease enzyme and maintaining its other qualities. The experimental results have shown that the drying kinetics of soybean in a two-dimensional spouted bed dryer are of the form described in the thin layer drying. The expression for the model parameter in Newton's law of cooling equation accounting for the moisture contents and inlet air temperatures was developed. The initial moisture content and inlet air temperature conditions cause cracks in the kernels. The strong collision between kernels and deflector because of high superficial velocity leads to high percentage of broken soybeans in the spout region. However, the velocity of 15.9 m/s can reduce the breakage below 5%. The inactivation of urease at low-to-moderate moisture content is suitably described by the first order kinetics. The modified Monod equation is applied when the moisture content is higher than 26% dry basis due to the inhibitory effect of water content on the inactivation rate. To complete urease inactivation and maintain protein quality, the temperatures of 150°C should be used.     

Drying and Urease Inactivation Models of Soybean Using Two-dimensional Spouted Bed Technique

The most important factors for examining the quality of soybeans in the animal feed industry are moisture and urease inactivation. Mathematical models for soybean drying and urease inactivation using two-dimensional spouted bed are developed and validated with experimental data. The influences of initial moisture content, inlet air temperature, air recycle on the drying rate, urease inactivation, and energy consumption are also studied. The results revealed that the increase in initial moisture content slightly affected the drying rate and urease inactivation while the inlet air temperature caused a significant effect. To obtain a high drying rate and save energy consumption, the recycle air ratio should be kept in a range of 80-90%.     

Drying and Urease Inactivation Models of Soybean Using Two-dimensional Spouted Bed Technique

The most important factors for examining the quality of soybeans in the animal feed industry are moisture and urease inactivation. Mathematical models for soybean drying and urease inactivation using two-dimensional spouted bed are developed and validated with experimental data. The influences of initial moisture content, inlet air temperature, air recycle on the drying rate, urease inactivation, and energy consumption are also studied. The results revealed that the increase in initial moisture content slightly affected the drying rate and urease inactivation while the inlet air temperature caused a significant effect. To obtain a high drying rate and save energy consumption, the recycle air ratio should be kept in a range of 80–90%.     

BATCH DRYING OF SHELLED CORN IN TWO-DIMENSIONAL SPOUTED BEDS WITH DRAFT PLATES

Geometrically similar spouted beds with draft plates were used to obtain the drying characteristics of freshly harvested shelled corn with 0.28 to 0.31 kg/kg initial moisture content at different air inlet temperatures and bed heights. Thermal equilibrium between air and grains was achieved at minimum spouting conditions. The drying kinetics of shelled corn in a drafted two-dimensional spouted bed was found to be of the "thin layer" type. Expressions for the model parameters in Page's equation accounting for the bed geometry, grain moisture content, and drying conditions were developed.     

BATCH DRYING OF SHELLED CORN IN TWO-DIMENSIONAL SPOUTED BEDS WITH DRAFT PLATES

ABSTRACT

Geometrically similar spouted beds with draft plates were used to obtain the drying characteristics of freshly harvested shelled corn with 0.28 to 0.31 kg/kg initial moisture content at different air inlet temperatures and bed heights. Thermal equilibrium between air and grains was achieved at minimum spouting conditions. The drying kinetics of shelled corn in a drafted two-dimensional spouted bed was found to be of the "thin layer" type. Expressions for the model parameters in Page's equation accounting for the bed geometry, grain moisture content, and drying conditions were developed.     

Drying of industrial sludge waste in a conical spouted bed dryer. Effect of air temperature and air velocity

To determine the performance of a conical spouted bed dryer for the drying of sludge waste, an experimental study of drying in a spouted bed regime was performed under different experimental conditions. The drying performance was determined based on the time evolution of solid moisture content, and the influence of operating conditions (inlet air temperature, air flow rate, and bed mass) on the drying rate of sludge waste in spouted beds of a conical geometry was analyzed.     

Drying Behavior of Carrots Dried in a Spout–Fluidized Bed Dryer

The effect of water blanching treatment and the inlet air temperature on drying kinetics as well as the quality attributes of carrot cubes dried in a spout–fluidized bed dryer at 60, 70, 80, and 90°C were analyzed. The material shrinkage and the rehydration potential were calculated to assess the changes in quality of dried carrots. It was found that the value of the air velocity during the drying of carrot cubes in a spout–fluidized bed dryer should be related to the moisture content of the carrot particles. A high value of air velocity at the beginning of the drying cycle and a lower value for the later stages were also required. The linear equation was correlated to the data of shrinkage of raw and blanched carrots. Blanching significantly influenced the coefficients in the shrinkage model derived for drying of carrot cubes in a spout–fluidized bed dryer, while drying temperature did not influence the shrinkage of carrot particles. The intensity of heat and mass transfer during spout–fluidized drying of carrot cubes was dependent on the drying temperature. A correlation was developed to calculate the values of effective moisture diffusivity of dried carrot cubes as a function of the moisture content and temperature of the material. It was observed that for any given time of rehydration, both the moisture content and the rehydration ratio calculated for samples dried at 60°C were higher than for samples dried at temperatures of 60, 70, 80, and 90°C.     

A TWO-REGION MATHEMATICAL MODEL FOR BATCH DRYING OF GRAINS IN A TWO-DIMENSIONAL SPOUTED BED

A two-region non-equilibrium model of a two-dimensional spouted bed dryer has been developed. The model, based on heat and mass transfer interactions between the spout and downcomer regions, predicts the air and grain temperatures and moisture content throughout each elementary thin layer of grain in the spouted bed. The model was validated with the experimental results on batch drying of corn. Drying and heating processes are shown to occur in both the spout and downcomer regions. Overall, the agreement between experimental and simulated results is satisfactory.     

A TWO-REGION MATHEMATICAL MODEL FOR BATCH DRYING OF GRAINS IN A TWO-DIMENSIONAL SPOUTED BED

A two-region non-equilibrium model of a two-dimensional spouted bed dryer has been developed. The model, based on heat and mass transfer interactions between the spout and downcomer regions, predicts the air and grain temperatures and moisture content throughout each elementary thin layer of grain in the spouted bed. The model was validated with the experimental results on batch drying of corn. Drying and heating processes are shown to occur in both the spout and downcomer regions. Overall, the agreement between experimental and simulated results is satisfactory.     

Drying characteristics of a draft tube spouted bed

Using the results of earlier work on the flow pattern of gas and solids in a draft-tube spouted bed, the drying characteristics of such a spouted bed are discussed. Paddy (unpeeled rice) was dried in a 30 cm bed with a 5.5 cm draft tube and temperatures and moisture content of solid and gas phase were measured as a function of drying time at various points in the system. It appears that the (constant) drying rate is determined by the heat transfer in the recirculation zone (just above the air inlet) and in the draft tube. After the short and rapid heating in the tube, the temperature and moisture gradients in the particle equilibrate in the annulus. It is concluded that a draft-tube spouted bed is a promising dryer design for heat-sensitive particles with slow intra-particle mass transfer coefficients.     

Experimental Study and Mathematical Modeling of Green Pea Drying in a Spouted Bed

In this study, green pea drying is investigated experimentally in a laboratory-scale spouted bed dryer. A mathematical model is also developed to investigate the effect of operating conditions on the performance of the system. The effect of operating parameters such as inlet air temperature, particle size, and flow rate of the drying air on the performance of the dryer are studied experimentally. In order to build the process model, it is necessary to analyze the transport in both solid and gas phases. A complete set of equations with no adjustable parameters is derived for existing zones in the spouted bed dryer in order to predict variations in the temperature and moisture content of the solid and gas phases with time for batch drying conditions. Model results are compared with corresponding experimental data. Agreement between the model results and experimental data is good.     

Drying Kinetics and Quality of Soy Residue (Okara) Dried in a Jet Spouted-Bed Dryer

The objective of this study was to investigate experimentally the effects of various drying parameters, i.e., inlet air velocity, inlet air temperature, initial bed height and heating duration, on both the drying kinetics and various quality attributes of dried okara viz. percentage changes of the total protein content, color, urease index, as well as the specific energy consumption during drying in a jet spouted-bed dryer. It was observed that all drying conditions tested could reduce the amount of urease to an acceptable level and increasing the heating duration, air velocity, and hot air temperature led to a significantly higher rate of reduction of urease activity. The percentage change of the total protein content of okara undergoing different drying conditions was not significantly different, however. After drying, the redness of okara was the highest changing color index, but its absolute value was still much lower than those observed for the lightness and yellowness. Hence, dried okara appeared light-brown. The specific energy consumption of the process was found to be in the range of 3.69 to 5.89 MJ/kg evaporated water.     

DRYING CHARACTERISTICS OF CORN IN FLUIDIZED BED DRYER

A batch fluidized bed dryer was carried out for corn drying. Drying characteristics of corn were investigated The experimental results indicated that moisture transfer inside a corn kernel was controlled by internal diffusion by the following conditions : inlet hot air temperatures of 120 - 200 °C, superficial air velocities of 2.2- 4 m/s, bed depths of 4 - 12 cm, fraction of air recycled of 0.5 -0.9 and initial moisture content of corn of 43 % dry-basis. The Wang and Sing equation could describe in accordance with the results. Inlet hot air temperature and specific air flow rate were independent variables for drying constant model in the Wang and Singh equation.     

DRYING OF PULP AND PAPER SLUDGE IN A PULSED FLUID BED DRYER

Hydrodynamics and drying kinetics for the pulp and paper primary sludge dried in a pulsed fluid bed dryer with relocated air stream are presented. Batch experiments have indicated that drying of disintegrated sludge to the required 12% moisture content takes place during the first drying period at practically constant material temperature close to the wet bulb temperature with respect to the inlet air conditions. Equations were developed for pressure drop, minimum pulsed-fluidization velocity, dynamic bed height, and volumetric mass transfer coefficient. Continuous experiments under drying conditions determined from the average residence time concept have confirmed that transportation of disintegrated sludge along the dryer follows the plug flow model.     

DRYING OF PULP AND PAPER SLUDGE IN A PULSED FLUID BED DRYER

ABSTRACT

Hydrodynamics and drying kinetics for the pulp and paper primary sludge dried in a pulsed fluid bed dryer with relocated air stream are presented. Batch experiments have indicated that drying of disintegrated sludge to the required 12% moisture content takes place during the first drying period at practically constant material temperature close to the wet bulb temperature with respect to the inlet air conditions. Equations were developed for pressure drop, minimum pulsed-fluidization velocity, dynamic bed height, and volumetric mass transfer coefficient. Continuous experiments under drying conditions determined from the average residence time concept have confirmed that transportation of disintegrated sludge along the dryer follows the plug flow model.

     

Drying Kinetics and Quality of Soy Residue (Okara) Dried in a Jet Spouted-Bed Dryer

ABSTRACT

The objective of this study was to investigate experimentally the effects of various drying parameters, i.e., inlet air velocity, inlet air temperature, initial bed height and heating duration, on both the drying kinetics and various quality attributes of dried okara viz. percentage changes of the total protein content, color, urease index, as well as the specific energy consumption during drying in a jet spouted-bed dryer. It was observed that all drying conditions tested could reduce the amount of urease to an acceptable level and increasing the heating duration, air velocity, and hot air temperature led to a significantly higher rate of reduction of urease activity. The percentage change of the total protein content of okara undergoing different drying conditions was not significantly different, however. After drying, the redness of okara was the highest changing color index, but its absolute value was still much lower than those observed for the lightness and yellowness. Hence, dried okara appeared light-brown. The specific energy consumption of the process was found to be in the range of 3.69 to 5.89 MJ/kg evaporated water.     

A MATHEMATICAL MODEL FOR CONTINUOUS DRYING OF GRAINS IN A SPOUTED BED DRYER

A mathematical model for a continuous spouted bed dryer has been presented to predict moisture content, air and grain temperatures as well as energy consumption. To better understand the interactive influence of processes in each region of the spouted bed, solution schemes for the spout and downcomer were treated separately. The behavior of dryer was investigated experimentally and found that the dryer behaved differently from an ideal plug flow. The drying rate as simulated by the model is almost constant during grain movement in the dryer. Absence of airflow in the downcomer leads to a tempering process that takes place in the downcomer while intense heat and mass transfer occurs mainly in the spout due to the high airflow rate there. Furthermore, by considering the predicted grain temperature history as one of the indicators of product quality, one can, in principle, design appropriate successive processes in a continuous spouted bed dryer to minimize product damage.     

A MATHEMATICAL MODEL FOR CONTINUOUS DRYING OF GRAINS IN A SPOUTED BED DRYER

ABSTRACT

A mathematical model for a continuous spouted bed dryer has been presented to predict moisture content, air and grain temperatures as well as energy consumption. To better understand the interactive influence of processes in each region of the spouted bed, solution schemes for the spout and downcomer were treated separately. The behavior of dryer was investigated experimentally and found that the dryer behaved differently from an ideal plug flow. The drying rate as simulated by the model is almost constant during grain movement in the dryer. Absence of airflow in the downcomer leads to a tempering process that takes place in the downcomer while intense heat and mass transfer occurs mainly in the spout due to the high airflow rate there. Furthermore, by considering the predicted grain temperature history as one of the indicators of product quality, one can, in principle, design appropriate successive processes in a continuous spouted bed dryer to minimize product damage.     

DRYING CHARACTERISTICS OF CORN IN FLUIDIZED BED DRYER

ABSTRACT

A batch fluidized bed dryer was carried out for corn drying. Drying characteristics of corn were investigated The experimental results indicated that moisture transfer inside a corn kernel was controlled by internal diffusion by the following conditions : inlet hot air temperatures of 120 - 200 °C, superficial air velocities of 2.2- 4 m/s, bed depths of 4 - 12 cm, fraction of air recycled of 0.5 -0.9 and initial moisture content of corn of 43 % dry-basis. The Wang and Sing equation could describe in accordance with the results. Inlet hot air temperature and specific air flow rate were independent variables for drying constant model in the Wang and Singh equation.     

Modeling of Moisture and Temperature Changes of Wheat during Drying in a Triangular Spouted Bed Dryer

A mathematical model of temperature and wheat moisture content distribution inside a triangular spouted bed dryer was developed. The model is based on analysis of heat and mass transfer inside the dryer. In addition to that, an empirical bulk density model has been developed for wheat and included in the drying simulation. A laboratory-scale triangular spouted bed (TSB) dryer was used to dry wheat grain to validate the model. The dryer was divided into three sections, namely spouting, downcomer, and fountain. A series of drying runs were conducted to record moisture and temperature profile. There were two distinct regions observed during wheat drying. A constant rate period was observed during the initial drying stage and the falling rate period took place at the later drying stage. Initial moisture content and operating drying temperature governed the timing of transition from constant rate period to falling rate period. The model can be used to accurately predict the moisture content of wheat during drying. The temperature prediction inside the TSB dryer was less accurate, especially at high temperatures due to heat losses in the experimental dryer. Further studies are needed to improve the accuracy of this model, especially with regard to the temperature prediction.