A 0.18μm CMOS Gilbert low noise mixer with noise cancellation

正This paper presents a broadband Gilbert low noise mixer implemented with noise cancellation technique operating between 10 MHz and 0.9 GHz.The Gilbert mixer is known for its perfect port isolation and bad noise performance.The noise cancellation technique of LNA can be applied here to have a better NF.The chip is implemented in SMIC 0.18μm CMOS technology.Measurement shows that the proposed low noise mixer has a 13.7-19.5 dB voltage gain from 10 MHz to 0.9 GHz,an average noise figure of 5 dB and a minimum value of 4.3 dB.The core area is 0.6 x 0.45 mm~2.     

A wideband current-commutating passive mixer for multi-standard receivers in a 0.18 μm CMOS

This paper reports a wideband passive mixer for direct conversion multi-standard receivers.A brief comparison between current-commutating passive mixers and active mixers is presented.The effect of source and load impedance on the linearity of a mixer is analyzed.Specially,the impact of the input impedance of the transimpedance amplifier(TIA),which acts as the load impedance of a mixer,is investigated in detail.The analysis is verified by a passive mixer implemented with 0.18 m CMOS technology.The circuit is inductorless and can operate over a broad frequency range.On wafer measurements show that,with radio frequency(RF) ranges from 700 MHz to 2.3 GHz,the mixer achieves 21 dB of conversion voltage gain with a-1 dB intermediate frequency(IF) bandwidth of 10 MHz.The measured IIP3 is 9 dBm and the measured double-sideband noise figure(NF) is 10.6 dB at 10 MHz output.The chip occupies an area of 0.19 mm2 and drains a current of 5.5 mA from a 1.8 V supply.     

Low power high gain gain-controlled LNA and mixer for GNSS receivers Wei Binbin(魏斌斌)1, Jiang Jinguang(江金光)1,2,3*

A low power high gain gain-controlled LNA ＋ mixer for GNSS receivers is reported. The high gain LNA is realized with a current source load. Its gain-controlled ability is achieved using a programmable bias circuit. Taking advantage of the high gain LNA, a high noise figure passive mixer is adopted. With the passive mixer, low power consumption and high voltage gain of the LNA ＋ mixer are achieved. To fully investigate the performance of this circuit, comparisons between a conventional LNA ＋ mixer, a previous low power LNA ＋ mixer, and the proposed LNA ＋ mixer are presented. The circuit is implemented in 0.18 #m mixed-signal CMOS technology. A 3.8 dB noise figure, an overall 45 dB converge gain and a 10 dB controlled gain range of the two stages are measured. The chip occupies 0.24 mm2 and consumes 2 mA current under 1.8 V supply.     

A 0.18μm CMOS single-inductor single-stage quadrature frontend for GNSS receiver

This paper presents an improved merged architecture for a low-IF GNSS receiver frontend,where the bias current and functions are reused in a stacked quadrature LNA-mixer-VCO.Only a single spiral inductor is implemented for the LC resonator and an extra 1/2 frequency divider is added as the quadrature LO signal generator. The details of the design are presented.The gain plan and noise figure are discussed.The phase noise,quadrature accuracy and power consumption are improved.The test chip is fabricated though a 0.18μm RF CMOS process. The measured noise figure is 5.4 dB on average,with a gain of 43 dB and a IIP3 of-39 dBm.The measured phase noise is better than -105 dBc/Hz at 1 MHz offset.The total power consumption is 19.8 mW with a 1.8 V supply. The experimental results satisfy the requirements for GNSS applications.     

A reconfigurable passive mixer for multimode multistandard receivers in 0.18 μm CMOS

This paper presents a reconfigurable quadrature passive mixer for multimode multistandard receivers. By using controllable transconductor and transimpedance-amplifier stages, the voltage conversion gain of the mixer is reconfigured according to the requirement of the selected communication standard Other characteristics such as noises figure, linearity and power consumption are also reconfigured consequently. The design concept is verified by implementing a quadrature passive mixer in 0.18 μm CMOS technology. On wafer measurement results show that, with the input radio frequency ranges from 700 MHz to 2.3 GHz, the mixer achieves a controllable voltage conversion gain from 4 to 22 dB with a step size of 6 dB. The measured maximum ⅡP3 is 8.5 dBm and the minimum noise figure is 8.0 dB. The consumed current for a single branch (I or Q) ranges from 3.1 to 5.6 mA from a 1.8 V supply voltage. The chip occupies an area of 0.71 mm² including pads.     

A multi-mode multi-band RF receiver front-end for a TD-SCDMA/LTE/LTE-advanced in 0.18-μm CMOS process

正A fully integrated multi-mode multi-band directed-conversion radio frequency(RF) receiver front-end for a TD-SCDMA/LTE/LTE-advanced is presented.The front-end employs direct-conversion design,and consists of two differential tunable low noise amplifiers(LNA),a quadrature mixer,and two intermediate frequency(IF) amplifiers.The two independent tunable LNAs are used to cover all the four frequency bands,achieving sufficient low noise and high gain performance with low power consumption.Switched capacitor arrays perform a resonant frequency point calibration for the LNAs.The two LNAs are combined at the driver stage of the mixer,which employs a folded double balanced Gilbert structure,and utilizes PMOS transistors as local oscillator(LO) switches to reduce flicker noise.The front-end has three gain modes to obtain a higher dynamic range.Frequency band selection and mode of configuration is realized by an on-chip serial peripheral interface(SPI) module.The frontend is fabricated in a TSMC 0.18-μm RF CMOS process and occupies an area of 1.3 mm~2.The measured doublesideband (DSB) noise figure is below 3.5 dB and the conversion gain is over 43 dB at all of the frequency bands. The total current consumption is 31 mA from a 1.8-V supply.     

A 2.4GHz CMOS Monolithic Transceiver Front-End for IEEE 802.11b Wireless LAN Applications

A 2.4GHz CMOS monolithic transceiver front-end for IEEE 802.11b wireless LAN applications is presented.The receiver and transmitter are both of superheterodyne structure for good system performance.The front-end consists of five blocks:low noise amplifier,down-converter,up-converter, pre-amplifier,and LO buffer.Their input/output impedance are all on-chip matched to 50Ω except the down-converter which has open-drain outputs.The transceiver RF front-end has been implemented in a 0.18μm CMOS process.When the LNA and the down-converter are directly connected,the measured noise figure is 5.2dB,the measured available power gain 12.5dB,the input 1dB compression point -18dBm,and the third-order input intercept point -7dBm.The receiver front-end draws 13.6mA currents from the 1.8V power supply.When the up-converter and pre-amplifier are directly connected,the measured noise figure is 12.4dB,the power gain is 23.8dB,the output 1dB compression point is 15dBm,and the third-order output intercept point is 16dBm.The transmitter consumes 276mA current from the 1.8V power supply.     

A 0.18μm CMOS low noise amplifier using a current reuse technique for 3.1-10.6 GHz UWB receivers

A new,low complexity,ultra-wideband 3.1-10.6 GHz low noise amplifier(LNA),designed in a chartered 0.18μm RFCMOS technology,is presented.The ultra-wideband LNA consists of only two simple amplifiers with an inter-stage inductor connected.The first stage utilizing a resistive current reuse and dual inductive degeneration technique is used to attain a wideband input matching and low noise figure.A common source amplifier with an inductive peaking technique as the second stage achieves high flat gain and wide -3 dB bandwidth of the overall amplifier simultaneously.The implemented ultra-wideband LNA presents a maximum power gain of 15.6 dB,and a high reverse isolation of—45 dB,and good input/output return losses are better than -10 dB in the frequency range of 3.1-10.6 GHz.An excellent noise figure(NF) of 2.8-4.7 dB was obtained in the required band with a power dissipation of 14.1 mW under a supply voltage of 1.5 V.An input-referred third-order intercept point(IIP3) is -7.1 dBm at 6 GHz.The chip area,including testing pads,is only 0.8×0.9 mm2.     

A RF receiver frontend for SC-UWB in a 0.18-μm CMOS process

正A radio frequency(RF) receiver frontend for single-carrier ultra-wideband(SC-UWB) is presented. The front end employs direct-conversion architecture,and consists of a differential low noise amplifier(LNA),a quadrature mixer,and two intermediate frequency(IF) amplifiers.The proposed LNA employs source inductively degenerated topology.First,the expression of input impedance matching bandwidth in terms of gate-source capacitance, resonant frequency and target S_(11) is given.Then,a noise figure optimization strategy under gain and power constraints is proposed,with consideration of the integrated gate inductor,the bond-wire inductance,and its variation.The LNA utilizes two stages with different resonant frequencies to acquire flat gain over the 7.1-8.1 GHz frequency band,and has two gain modes to obtain a higher receiver dynamic range.The mixer uses a double balanced Gilbert structure.The front end is fabricated in a TSMC 0.18-/im RF CMOS process and occupies an area of 1.43 mm~2.In high and low gain modes,the measured maximum conversion gain are 42 dB and 22 dB,input 1 dB compression points are -40 dBm and -20 dBm,and S_(11) is better than -18 dB and -14.5 dB.The 3 dB IF bandwidth is more than 500 MHz.The double sideband noise figure is 4.7 dB in high gain mode.The total power consumption is 65 mW from a 1.8 V supply.     

A 3.125-Gb/s inductorless transimpedance amplifier for optical communication in 0.35μm CMOS

A 3.125-Gb/s transimpedance amplifier(TIA) for an optical communication system is realized in 0.35μm CMOS technology.The proposed TIA employs a regulated cascode configuration as the input stage, and adopts DC-cancellation techniques to stabilize the DC operating point.In addition,noise optimization is processed. The on-wafer measurement results show the transimpedance gain of 54.2 dBΩand -3 dB bandwidth of 2.31 GHz.The measured average input referred noise current spectral density is about 18.8 pA/(?).The measured eye diagram is clear and symmetrical for 2.5-Gb/s and 3.125-Gb/s PRBS.Under a single 3.3-V supply voltage,the TIA consumes only 58.08 mW,including 20 mW from the output buffer.The whole die area is 465×435μm~2.     

An Implementation of a CMOS Down-Conversion Mixer for GSM1900 Receivers

介绍了一种0.18μm CMOS工艺基于GSM1900(PCS1900)标准低中频接收机中的混频器.该混频器采用了一种新型的折叠式吉尔伯特单元结构.在3.3V电源电压、中频频率为100kHz的情况下,该混频器达到了6dB的转换增益,18.5dB的噪声系数(1MHz中频)和11.5dBm IIP3的高线性度,同时仅消耗7mA电流.     

A Novel Offset-Cancellation Technique for Low Voltage CMOS Differential Amplifiers

基于对CMOS差分放大器的非线性和元件失配理解的基础上,提出了一种应用于低电压CMOS差分放大器的失调取消技术.这种技术在不需要增加功耗的基础上,通过把输出端的失调电压转移到差分放大器的其他节点,从而达到减小输入参考的失调电压的目的.为了验证这种技术,设计了一个工作电压为1.8V的低失调的CMOS差分放大器.仿真结果表明,在负载晶体管的失配为20%,输入放大管的失配为10%时,利用这种失调转移技术,输入参考的失调可以减少40%.同已发表的失调取消技术相比,利用这种技术可以达到更低的功耗和更高的集成度.     

A Wide-Band High-Linearity Down-Conversion Mixer for Cable Receptions

分析了一种宽带高线性度的用于有线接收机的下变频混频器.该设计采用0.35μm SiGe BiCMOS工艺.射频输入信号频率范围设计为1～1.8GHz,测得的1dB压缩点达到 14.23dBm,最大转换增益为8.31dB,最小噪声系数为19.4dB,在5V供电情况下,直流功耗为54mW.     

A Wide-Band Low Noise Amplifier for Terrestrial and Cable Receptions

提出并设计了一种用于数字电视接收调谐芯片的宽带低噪声放大器.该设计采用0.35μm SiGe BiCMOS工艺,器件的主要性能为:增益等于18.8dB,增益平坦度小于1.4dB,噪声系数小于5dB,1dB压缩点为-2dBm,输入三阶交调为8dBm.在5V供电的情况下,直流功耗为120mW.     

A 12-Channel,30Gb/s,0.18μm CMOS Front-End Amplifier for Parallel Optic-Fiber Receivers

给出了一个采用TSMC 0.18μm CMOS工艺设计并实现的12路30Gb/s并行光接收前端放大器.电路设计采用RGC结构和噪声优化技术,克服了CMOS光检测器大寄生电容造成的带宽不够的问题.测试结果表明,在2pF的寄生电容下单信道传输速率达到了2.5Gb/s,在0.8mVpp输入下得到了清晰的眼图.提出了一种同时采用p 保护环(PGR)、n 保护环(NGR)和深n阱(DNW)的并行放大器隔离结构,有效地抑制了并行放大器之间的串扰,减小了放大器之间的衬底耦合噪声.测量结果表明,这种结构与PGR和PGR NGR相比,在1GHz时放大器之间的隔离度分别提高了29.2和8.1dB,在2GHz时放大器之间的隔离度分别提高了8.1和2.5dB.芯片采用1.8V电源供电,单路前端放大器的功耗为85mW,12路总功耗约为1W.