ZrO2（Y—TZP）—Si3N4复合材料中抑制ZrN生成研究

研究了气氛加压烧成ＺｒＯ２（Ｙ－ＴＺＰ）－Ｓｉ３Ｎ４复合材料中抑制ＺｒＮ生成工艺问题，相组成分析表明：无论添加≤２０ｗｔ％工业ＺｒＯ２或者Ｙ－ＴＺＰ（３ｍｏｌ％Ｙ２Ｏ３）的氮化硅复合材料，在低于１８５０℃，３ＭＰａ氮气压力下烧成，表面无ＺｒＮ生成。     

添加Al_2O_3对SiC板粒／Y－TZP复合材料力学性能的影响

本文以ＳｉＣ板粒、ＺｒＯＣｌ２－８Ｈ２Ｏ、ＡｌＣｌ３和Ｙ（ＭＯ）３为原料，利用共沉淀和热压烧结工艺，制备ＳｉＣ板粒／Ｙ－ＴＺＰ和（含Ａｌ２Ｏ３）ＳｉＣ板粒／Ｙ－ＴＺＰ复合材料．测试了材料的室温和高温力学性能．研究了添加Ａｌ２Ｏ３对ＳｉＣ板粒／Ｙ－ＴＺＯ复合材料的影响．结果表明，ＳｉＣ板粒／Ｙ－ＴＺＰ复合材料与Ｙ－ＴＺＰ陶瓷相比，其室温强度和韧性出现明显下降，高温强度也没有改善；而在ＳｉＣ板粒与Ｙ－ＴＺＰ复合的基础上，添加Ａｌ２Ｏ３可明显提高材料的强度和断裂韧性，同时，材料的高温强度也获得显著改善．     

添加Al2O3对SiC板粒／Y—TZP复合材料力学性能的影响

本以ＳｉＣ板粒、ＺｒＯＣｌ２·８Ｈ２Ｏ、ＡｌＣｌ３和Ｙ（ＭＯ）３为原料，利用共沉淀和热压烧结工艺，制备ＳｉＣ板粒／Ｙ－ＴＺＰ和（含Ａｌ２Ｏ３）ＳｉＣ板粒／Ｙ－ＴＺＰ复合材料。测试了材料的室温和高温力学性能。研究了添加Ａｌ２Ｏ３对ＳｉＣ板粒／Ｙ－ＴＺＯ复合材料的影响。结果表明，ＳｉＣ板粒／Ｙ－ＴＺＰ复合材料与Ｙ－ＴＺＰ复合材料与Ｙ－ＴＺＰ陶瓷相比，其室温强度和韧性出现明显下降，高温强度也没有改善；     

ZrO2-Si3N4陶瓷复合材料中的化学不相容性

ＺｒＯ２与Ｓｉ３Ｎ４之间存在化学反应生成ＺｒＮ或氧氮化锆,ＺｒＯ２也可能被氮稳定形成氮稳定的ＺｒＯ２。本文对ＺｒＯ２－Ｓｉ３Ｎ４陶瓷复合材料中的化学不相容性及抑制措施进行了综述。     

LCMAS微晶玻璃／Y－TZP复相材料

本工作对ＬＣＭＡＳ微晶玻璃／Ｙ－ＴＺＰ复相材料在不同的烧结温度下所出现的晶相进行了研究，发现材料在烧结温度下，Ｙ－ＴＺＰ中的ＺｒＯ２与微晶玻璃中的ＳｉＯ２发生化学反应生成锆英石（ＺｒＯ２·ＳｉＯ２），少量Ｙ－ＴＺＰ的加入起不到相变增初作用．由于Ｙ－ＴＺＰ起到微晶玻璃晶核剂的作用，仍能使材料的抗折强度和断裂韧性得到大幅度的提高．当Ｙ－ＴＺＰ含量为９５ｗｔ％时，复相材料的抗折强度和断裂韧性分别为６３１ＭＰａ和８．４ＭＰａ．ｍ１／２．     

由SiO2/3Y-TZP包裹复合粉体制备ZrSiO4/3Y-TZP细晶陶瓷

对湿化学法制备的ＳｉＯ_２／３Ｙ－ＴＺＰ包裹复合粉体进行了热压烧结研究,并利用Ｘ射线衍射和透射电镜表征了烧结体的物相和显微结构．在低于１３００℃,复合粉体发生瞬时粘性烧结,材料密度迅速提高;随着烧结温度的升高,ＳＩＯ_２和ＺｒＯ_２发生反应生成ＺｒＳｉＯ_４．在１５００℃热压条件下,制备了平均晶粒尺寸为３５０ｎｍ的ＺｒＳｉＯ_４／３Ｙ－ＴＺＰ细晶复相材料．我们认为,在烧结过程中形成的第二相ＺｒＳｉＯ_４,特别是ＳｉＯ_２包裹层对抑制基体晶粒长大起主要作用．     

ZrO2-Si3N4陶瓷复合材料中的化学不相容性

ＺｒＯ_２与Ｓｉ_３Ｎ_４之间存在化学反应生成ＺｒＮ或氧氮化锆,ＺｒＯ_２也可能被氮稳定形成氨稳定的ＺｒＯ_２本文对ＺｒＯ_２－Ｓｉ_３Ｎ_４陶瓷复合材料中的化学不相容性及抑制措施进行了综述．     

Si及α－Al_2O_3超细粉对Al_2O_3－ZrO_2－C系材料显微结构的影

本文探讨了Ｓｉ及α－Ａｌ２Ｏ３超细粉对Ａｌ２Ｏ３－ＺｒＯ２－Ｃ系材料显微结构的影响．认为在Ａｌ２Ｏ３－ＺｒＯ２－Ｃ系材料中同时加入Ｓｉ和α－Ａｌ２Ｏ３超细粉，Ｓｉ粉除了与Ｃ生成了ＳｉＣ纤维外，其反应产物ＳｉＯ２还与α－Ａｌ２Ｏ３超细粉及ＺｒＯ２生成了莫来石（Ａ３Ｓ２）和Ａｌ２Ｏ３－ＺｒＯ２－ＳｉＯ２（ＡＺＳ）固溶体，这些新生成的矿物相对试样的显微结构产生重要的作用．     

陶瓷基复合材料（SiCw／Y—TZP）在循环压应力下的疲劳裂纹扩展

研究了碳化硅晶须（ＳｉＣｗ）增强，Ｙ２Ｏ３稳定的ＺｒＯ２四方多晶体（Ｙ－ＴＺＰ）复合材料（ＳｉＣｗ／Ｙ－ＴＺＰ）在循环压应力作用下的疲劳特性，单边缺口弯曲试样在纵向循环压应力作用下缺口根部产生垂直于压应力的Ｉ型裂纹，类似于金属材料，在室温下循环应力导致Ｉ型裂纹的稳定扩展。压应力在缺口根部产生的不可逆损伤区在循环卸载过程中形成较大的残余拉伸应力场，使裂纹萌生并长大，同时，裂纹面产生的碎粒及晶须拔出导     

SiC晶须增韧Al_2O_3及ZrO_2（Y_2O_3）基陶瓷复合材料的抗热震行

采用三点弯曲及扫描电镜等方法研究了ＳｉＣｗ／Ａｌ２Ｏ３、ＳｉＣｗ／ＺｒＯ３（Ｙ２Ｏ３）及ＳｉＣｗ／Ａｌ２Ｏ３＋ＺｒＯ２（Ｙ２Ｏ３）陶瓷复合材料的抗热震性．结果表现ＳｉＣｗ的加入使Ａｌ２Ｏ３、ＺｒＯ２（Ｙ２Ｏ３）以及Ａｌ２Ｏ３＋ＺｒＯ２（Ｙ２Ｏ３）基体的抗热震性显著提高，Ａｌ２Ｏ３陶瓷基复合材料的抗热震性明显优于ＺｒＯ２（Ｙ２Ｏ３）陶瓷基复复合材料．同时发现在Ａｌ２Ｏ３十ＳｉＣｗ材料基础上再加入少量ＺｒＯ２（２Ｙ）颗粒（１０Ｖｏ１％），也可进一步提高Ａｌ２Ｏ３＋ＳｉＣｗ材料的抗热震性．     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from     

CNAS Passes APLAC's PTP Review

正The review group of Asia Pacific Laboratory Accreditation Cooperation(APLAC)carried out a 4-day peer review of the proficiency testing provider(PTP)for China National Accreditation Service for Conformity Assessment(CNAS)from July 28 to 31,2014.CNAS passed the PTP review with excellent performance.Two senior peer reviewers of APLAC made a comprehensive,rigorous and detailed review of CNAS’s PTP accreditation activities,and made the on-spot inspection of the review groups in Shanghai and Shenzhen respectively.