Enhancing hydrogen production by dry reforming process with strontium promoter

Hydrogen is an ideal energy carrier and can play a very important role in the energy system. The present study investigated the enhancement of hydrogen production from catalytic dry reforming process. Two catalysts namely Ni/γ-Al₂O₃ and Co/γ-Al₂O₃ promoted with different amounts of strontium were used to explore selectivity and yield of hydrogen production. Spent and fresh catalysts were characterized using techniques such as BET, XRD, H₂-TPR, CO₂-TPD, TGA and O₂-TPO. The catalyst activity and characterization results displayed stability improvement due to addition of Sr promoter. The least coke formations i.e. 3.8 wt% and 5.1 wt% were obtained using 0.75 wt% Sr doped in Ni/γ-Al₂O₃ and 0.5 wt% Sr doped in Co/γ-Al₂O₃ catalysts respectively. Time on stream tests of promoted catalysts for about six hours at 700 °C showed stable hydrogen selectivity. Moreover, the hydrogen selectivity was significantly improved by the addition of Sr in Ni and Co based catalysts. For instance the hydrogen selectivity increased from 45.9% to 47.8% for Ni/γ-Al₂O₃ and from 48% to 50.9% for Co/γ-Al₂O₃ catalyst by the addition of 0.75 wt% Sr in Ni/γ-Al₂O₃ and 0.5 wt% Sr in Co/γ-Al₂O₃ catalyst respectively.     

Steam reforming of dimethyl ether over Cu–Ni/γ-Al2O3 bi-functional catalyst prepared by deposition–precipitation method

Cu–Ni/γ-Al₂O₃ catalysts with different metal contents for dimethyl ether steam reforming (DME SR) were prepared by the method of deposition–precipitation. Characterization of specific surface area measurement (BET), X-ray diffraction (XRD) and hydrogen temperature-programmed reduction (H₂-TPR) revealed that nickel improved the dispersion of copper, increased the interaction between copper and γ-Al₂O₃, and therefore, inhibited the sintering of copper. Ammonia temperature-programmed desorption (NH₃-TPD) showed that metal particles could occupy the acid sites, leading to the decrease in acid amount and acid strength of Cu–Ni/γ-Al₂O₃ catalyst. Kinetic measurements indicated that γ-Al₂O₃ is vital for DME SR and a higher content of γ-Al₂O₃ in catalyst was needed. The addition of nickel suppressed the water gas shift (WGS) reaction. Initial durability testing showed that the conversion of DME over Cu–Ni/γ-Al₂O₃ catalyst was always almost complete during the 30 h experimental reaction time. Therefore, Cu–Ni/γ-Al₂O₃ could be a potential DME SR catalyst for the production of hydrogen.     

Hydrogen production by biomass gasification in supercritical water over Ni/γAl2O3 and Ni/CeO2-γAl2O3 catalysts

Hydrogen production by supercritical water gasification (SCWG) is a promising technology for wet biomass utilization. Ni catalyst can realize the high gasification efficiency of biomass near the critical temperature of water. In this paper, Ni/γAl₂O₃ and Ni/CeO₂-γAl₂O₃ catalysts were prepared by an impregnation method. The catalyst performance for glucose gasification in supercritical water was tested in autoclave reactor. All experiments were carried out in the autoclave at 673 K, 24.5 MPa, and the concentration of glucose was 9.09 wt.%. The catalysts before and after reaction were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), BET specific surface area measurements, X-ray fluorescence spectrum (XRF) and Thermo-gravimetric analyses (TGA) in order to investigate on the chemical property and catalytic mechanism. The experimental results showed that hydrogen yield and hydrogen selectivity increased sharply with addition of Ni/γAl₂O₃ and Ni/CeO₂-γAl₂O₃ catalysts. The catalytic activity and H₂ selectivity of Ni/CeO₂-γAl₂O₃ was higher than that of Ni/γ-Al₂O₃ catalyst. The results revealed that carbon deposition and coking led to the deactivation of the catalysts. Ce in the Ni/CeO₂-γAl₂O₃ catalyst had a certain role in the inhibition of carbon deposition and coking.     

Hydrogen production by biomass gasification in supercritical water with bimetallic Ni-M/γAl2O3 catalysts (M = Cu, Co and Sn)

Supercritical water gasification (SCWG) of wet biomass is a very promising technology for hydrogen energy and the utilization of biomass resources. Ni-based catalysts are effective in catalyzing SCWG of original biomass and organic compounds for hydrogen production. In this paper, hydrogen production by SCWG of glucose over alumina-supported nickel catalysts modified with Cu, Co and Sn was studied. The bimetallic Ni-M (M = Cu, Co and Sn) catalysts were prepared by a co-impregnation method and tested in an autoclave reactor at 673 K with a feedstock concentration of 9.09 wt.%. XRD, XRF, N₂ adsorption/desorption, SEM and TGA were adopted to investigate the changes of chemical properties between Ni and Ni-M catalysts and the deactivation mechanism of catalysts. According to the experimental results, the hydrogen yield followed this order: Ni-Cu/γAl₂O₃ > Ni/γAl₂O₃ > Ni-Co/γAl₂O₃ > Ni-Sn/γAl₂O₃. The results show that Cu could improve the catalytic activity of Ni catalyst in reforming reaction of methane to produce hydrogen in SCWG. In addition, Cu can mitigate the sintering of alumina detected by SEM. Co was found to be an excellent promoter of Ni-based catalyst in relation to hydrogen selectivity.     

Support and alloy effects on activity and product selectivity for ethanol steam reforming over supported nickel cobalt catalysts

Ni, Co and bimetallic Ni–Co catalysts supported on Ca-γ-Al₂O₃ and ZrO₂ were investigated for the production of hydrogen via ethanol steam reforming (ESR). Catalysts were prepared by wet impregnation method and characterized using temperature-programmed reduction (TPR), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). ESR and temperature-programmed desorption of ethanol (ethanol-TPD) were carried out in a continuous flow fixed bed micro-reactor and the outlet gases were monitored by an on-line GC or MS. Ni is found to be more active for the C–C bond rupture than Co on both supports, Ca-γ-Al₂O₃ and ZrO₂. Catalyst support plays very important roles for the ESR. Strong interaction between support and metal affects the formation of NiCo bimetallic compound, resulting in the variety of catalytic activity. On Ca-γ-Al₂O₃ support, the catalytic activity of ESR follows the sequence of 10%Ni > 6.7%Ni 3.3%Co ∼ 3.3%Ni 6.7%Co > 10%Co. On ZrO₂, the trend is 10%Ni > 6.7%Ni 3.3%Co > 10%Co > 3.3%Ni 6.7%Co. The H₂O adsorption/activation ability of the support determines the reaction pathway and thus the product selectivity. On Ca-γ-Al₂O₃, water gas shift reaction is more favorable than on ZrO₂, due to the availability of surface OH groups. The roles of the metal and support for ESR are also discussed.     

Autothermal reforming of iso-octane and gasoline over Rh-based catalysts: Influence of CeO2/γ-Al2O3-based mixed oxides on hydrogen production

Autothermal reforming (ATR) of iso-octane in the presence of Rh-based catalysts (0.5 wt% of Rh) supported onto γ-Al₂O₃, CeO₂, and ZrO₂ were initially carried out at 700 °C with a S/C ratio of 2.0, an O/C ratio of 0.84, and a gas hourly space velocity (GHSV) of 20,000 h⁻¹. The activity of Rh/γ-Al₂O₃ was found to be higher than Rh/CeO₂ and Rh/ZrO₂, with H₂ and (H₂ + CO) yields of 1.98 and 2.48 mol/mol C, respectively, after 10 h. This Rh/γ-Al₂O₃ material, however, was potentially susceptible to carbon coking and produced 3.5 wt% of carbon deposits following the reforming reaction, as evidenced by C, H, N, and S elemental analysis. In contrast, Rh/CeO₂ catalyst exhibited lower activity but higher stability than Rh/γ-Al₂O₃, with nearly no carbon being formed within 10 h. To combine the superior activity originated from Rh/γ-Al₂O₃ with high stability from Rh/CeO₂, Rh/CeO₂/γ-Al₂O₃ catalysts with different CeO₂ contents were synthesized and examined for the ATR reactions of iso-octane. Compared to Rh/γ-Al₂O₃, the newly prepared Rh/CeO₂/γ-Al₂O₃ catalysts (0.5 wt% of Rh and 20 wt% of CeO₂) showed even enhanced activity during 10 h, and H₂ and (H₂ + CO) yields were calculated to be 2.08 and 2.62 mol/mol C, respectively. In addition, as observed with Rh/CeO₂, the catalyst was further found to be stable with less than 0.3 wt% of carbon deposition after 10 h. The Rh/γ-Al₂O₃ and Rh/CeO₂/γ-Al₂O₃ catalysts were eventually tested for ATR reactions using commercial gasoline that contained sulfur, aromatics, and other impurities. The Rh/γ-Al₂O₃ catalyst was significantly deactivated, showing decreased activity after 4 h, while the Rh/CeO₂/γ-Al₂O₃ catalyst proved to be excellent in terms of stability against coke formation as well as activity towards the desired reforming reaction, maintaining its ability for H₂ production for 100 h.     

CO2 reforming of methane on Ni/γ-Al2O3 catalyst prepared by dielectric barrier discharge hydrogen plasma

Ni/γ-Al₂O₃ catalyst was prepared by direct treatment of Ni(NO₃)₂/γ-Al₂O₃ precursor with dielectric barrier discharge (DBD) hydrogen plasma at different input powers, characterized by XRD, H₂-TPR, CO₂-TPD, N₂ adsorption and TEM, respectively, and used as the catalyst for CO₂ reforming of methane (CRM). The results showed that the input power obviously affected the reduction degree and catalytic performances of catalysts. Low input power under 40 W mainly resulted in the decomposition of nickel nitrate into Ni oxides. The reduction degree, catalytic activity and stability increase with the input power. Similar catalytic performances in CRM reaction can be obtained when the power exceeds 80 W. Compared with the Ni/Al₂O₃ catalyst prepared by traditional method, Ni/γ-Al₂O₃ samples prepared by H₂ DBD plasma exhibit better activities, stability and anti-carbon deposit performances. It is mainly ascribed to smaller Ni particle size, more basic sites and weaker basicity. The increase of Ni particle sizes due to the sintering at high temperature results in the decrease of catalytic activities and coke formation.     

Catalytic gasification of food waste in supercritical water over La promoted Ni/Al2O3 catalysts for enhancing H2 production

Ni/Al₂O₃ catalyst is the one of promising catalysts for enhancing H₂ production from supercritical water gasification (SCWG) of biomass. However, due to carbon deposition, the deactivation of Ni/Al₂O₃ catalyst is still a serious issue. In this work, the effects of lanthanum (La) as promoter on the properties and catalytic performance of Ni/Al₂O₃ in SCWG of food waste were investigated. La promoted Ni/Al₂O₃ catalysts with different La loading content (3–15 wt%) were prepared via impregnation method. The catalysts were characterized using XRD, SEM, BET techniques. The SCWG experiments were carried out in a Hastelloy batch reactor in the operating temperature range of 420–480 °C, and evaluated based on H₂ production. The stability of the catalysts was assessed by the amount of carbon deposition on catalyst surface and their catalytic activity after reuse cycles. The results showed that 9 wt% La promoter is the optimal loading as Ni/9La–Al₂O₃ catalyst performed best performance with the highest H₂ yield of 8.03 mol/kg, and H₂ mole fraction of 42.46% at 480 °C. La promoted Ni/Al₂O₃ catalysts have better anti-carbon deposition properties than bare Ni/Al₂O₃ catalyst, resulting in better gasification efficiency after reuse cycles. Ni/9La–Al₂O₃ catalyst showed high catalytic activity in SCWG of food waste and had good stability as it was still active for enhancing H₂ production when used in SCWG for the third time, which indicated that La promoted Ni/Al₂O₃ catalysts are potential additive to improve the SCWG of food waste.     

Properties of Ni/Y2O3 and its catalytic performance in methane conversion to syngas

Ni/Y₂O₃, with Y₂O₃ support prepared by the conventional precipitation method, was prepared by an impregnation method. The physicochemical properties of Y₂O₃ and Ni/Y₂O₃ were characterized by BET, CO₂-TPD, NH₃-TPD, TPR, XRF and TGA, and compared with those of γ-Al₂O₃ and Ni/γ-Al₂O_3, respectively. The catalytic performance of Ni/Y₂O₃ in the reaction of partial oxidation of methane (POM) to syngas was evaluated and compared with that of Ni/γ-Al₂O₃ catalyst, too. The results showed that, Y₂O₃ was a basic support with few acidic sites while γ-Al₂O₃ was an acidic support. NiO particles supported on Y₂O₃ were more easily to be reduced than those supported on γ-Al₂O₃. In the partial oxidation of methane, Ni/Y₂O₃ catalyst showed high catalytic activity and exhibited better catalytic stability than Ni/γ-Al₂O₃. After POM reaction at 700 °C for 550 h, methane conversion decreased little and only 2.2 wt% carbon was deposited on Ni/Y₂O₃ catalyst. Ni/Y₂O₃ was stable in POM even after a series of reaction temperature variations within the temperature range of 400 ∼ 800 °C.     

Coke-resistance enhancement of mesoporous γ-Al2O3 and MgO-supported Ni-based catalysts for sustainable hydrogen generation via steam reforming of acetic acid

Highly ordered mesoporous γ-Al₂O₃ particles and MgO materials were synthesized by evaporation induced self-assembly (EISA) and template-free hydrothermal co-precipitation routes, respectively. Ni, Ni–MgO, and Ni–La₂O₃-containing catalysts were prepared using a wet-impregnation method. The synthesized catalysts were characterized by N₂ adsorption–desorption, XRD, SEM-EDS, DRIFTS, XPS, TGA-DTA, and Raman spectroscopy analysis. The mesoporous γ-Al₂O₃ catalyst support exhibited a high surface area of 245 m²/g and average pore volume of 0.481 cm³/g. The DRIFTS results indicate the existence of large Lewis's acid regions in the pure γ-Al₂O₃ and metal-containing catalysts. Catalytic activity tests of pure materials and metal-containing catalysts were carried out at the reaction temperature of 750 °C and a feed molar ratio of AA/H₂O/Ar:1/2.5/2 over 3 h. Complete conversion of acetic acid and 81.75% hydrogen selectivity were obtained over the catalyst 5Ni@γ-Al₂O₃. The temperature and feed molar ratio had a noticeable impact on H₂ selectivity and acetic acid conversion. Increasing the water proportion in the feed composition from 2.5 to 10 considerably improved the catalytic activity by increasing hydrogen selectivity from 81.75% to 91%. Although the Ni-based γ-Al₂O₃-supported catalysts exhibited higher activity performance compared to the Ni-based MgO-supported catalysts, they were not as resistant to coke formation as were MgO-supported catalysts. The introduction of MgO and La₂O₃ into the Ni@γ-Al₂O₃ and Ni@MgO catalysts' structures played a significant role in lowering the carbon formation (from 37.15% to 17.6%–12.44% and 12.17%, respectively) and improving the thermal stability of the catalysts by decreasing the agglomeration of acidic sites and reinforcing the adsorption of CO₂ on the catalysts' surfaces. Therefore, coke deposition was reduced, and catalyst lifetime was improved.     

Supercritical water synthesized Ni/ZrO2 catalyst for hydrogen production from supercritical water gasification of glycerol

Catalysts are crucial to promote the technical feasibility of supercritical water gasification (SCWG) for H₂ production from wet biomass, yet catalysts prepared by conventional methods normally encounter sintering problems in supercritical water. Herein, a series of ZrO₂-supported Ni catalysts were tried to be prepared by supercritical water synthesis (SCWS) and evaluated for SCWG in terms of activity and property stability. The SCWS was conducted at 500 °C and 23 MPa using metal nitrates as starting materials. Effect of precursor concentration on property and catalytic performance of the SCWS-prepared catalysts for SCWG of 20 wt% glycerol were systematically studied. XRD, SEM-EDS, TEM and TGA were applied for catalyst characterization. Results verified the successful obtaining of Ni/ZrO₂ nanocatalysts with Ni crystals of 30–70 nm and ZrO₂ crystals of ~11 nm by the SCWS process, which were found to be active on the WGSR for SCWG to increase the H₂ yield as high as 155%. Importantly, the SCWS-prepared Ni/ZrO₂ catalysts exhibited excellent property stability and anti-coking ability for SCWG of glycerol.     

Hydrogen production by steam reforming of liquefied natural gas (LNG) over Ni/Al2O3–ZrO2 xerogel catalysts: Effect of calcination temperature of Al2O3–ZrO2 xerogel supports

Al₂O₃–ZrO₂ (AZ) xerogel supports prepared by a sol-gel method were calcined at various temperatures. Ni/Al₂O₃–ZrO₂ (Ni/AZ) catalysts were then prepared by an impregnation method for use in hydrogen production by steam reforming of liquefied natural gas (LNG). The effect of calcination temperature of AZ supports on the catalytic performance of Ni/AZ catalysts in the steam reforming of LNG was investigated. Crystalline phase of AZ supports was transformed in the sequence of amorphous γ-Al₂O₃ and amorphous ZrO₂ → θ-Al₂O₃ and tetragonal ZrO₂ → (θ + α)-Al₂O₃ and (tetragonal + monoclinic) ZrO₂ → α-Al₂O₃ and (tetragonal + monoclinic) ZrO₂ with increasing calcination temperature from 700 to 1300 °C. Nickel oxide species were strongly bound to γ-Al₂O₃ and θ-Al₂O₃ in the Ni/AZ catalysts through the formation of solid solution. In the steam reforming of LNG, both LNG conversion and hydrogen composition in dry gas showed volcano-shaped curves with respect to calcination temperature of AZ supports. Nickel surface area of Ni/AZ catalysts was well correlated with catalytic performance of the catalysts. Among the catalysts tested, Ni/AZ1000 (nickel catalyst supported on AZ support that had been calcined at 1000 °C) with the highest nickel surface area showed the best catalytic performance. Well-developed and pure tetragonal phase of ZrO₂ in the AZ1000 support played an important role in the adsorption of steam and the subsequent spillover of steam from the support to the active nickel.     

Mesocellular-foam-silica-supported Ni catalyst: Effect of pore size on H2 production from cellulose pyrolysis

Supported nickel metal can be used as a tar-cracking catalyst in the thermal processing of large organics to give H₂. Though porous supports offer the opportunity to disperse a relatively large amount of nickel, catalytic sites within small pores may be inaccessible to large tar molecules. To investigate this, we prepared nickel catalysts supported on γ-Al₂O₃ and on SBA-15- and mesocellular-foam-(MCF)-type silicas and studied their catalytic activities in the pyrolytic decomposition of cellulose (RT → 800 °C, ∂T/∂t = 40 °C/min). A thermogravimetric analyser-mass spectrometer (TG-MS) was used to study the influence of the Ni catalyst and support materials on the H₂ yield and selectivity. The silica-MCF-supported Ni catalyst decreased char residue and enhanced H₂ yield, producing 1.6 and 3.5× the H₂ yield obtained using SBA-15-supported Ni and γ-Al₂O₃-supported Ni, respectively. MCF, with ultra-large pores (d ∼ 15−50 nm), was thus identified as the most beneficial catalyst support for this application.     

Catalytic reforming of glycerol in supercritical water with nickel-based catalysts

The catalytic performance of nickel catalysts supported on La₂O₃, α-Al₂O₃, γ-Al₂O₃, ZrO₂, and YSZ for supercritical water reforming of glycerol was investigated. Experiments were conducted in a tubular reactor made of Inconel-625 with the temperature range of 723–848 K under a pressure of 25 MPa. Carbon formation causing operation failure was observed for α-Al₂O₃, γ-Al₂O₃ and ZrO₂ at temperatures higher than 748, 798 and 823 K, respectively. Ni/La₂O₃ exhibited the highest H₂ yield where almost complete conversion was obtained at 798 K. Moderate space velocities (WHSV = 6.45 h⁻¹) and glycerol feed concentration (5wt.%) favor high hydrogen selectivity and yield. Methanation is favored at a low WHSV or high glycerol feed concentration, resulting in a lower H₂ yield. Increasing Ni loading on the Ni/La₂O₃ catalyst strongly promoted the reforming, water–gas shift, and methanation reactions, which contributed significantly to the product species distribution.     

Hydrogen generation from Al-Water reaction promoted by M-B/γ-Al2O3 (M = Co,Ni) catalyst

Al-water reaction promoted by catalysts is a promising hydrogen generation technology. In this work, a high-activity M-B/γ-Al₂O₃ (M = Co, Ni) catalyst is prepared by wet chemical reduction method. It is found that M-B/γ-Al₂O₃ catalyst significantly promotes the Al-water reaction and decreases the induction time. When the molar ratio of γ-Al₂O₃ to Co-M in Co–B/γ-Al₂O₃ catalyst is 1:1, the induction time is only 0.43 h. The catalytic activity of M-B/γ-Al₂O₃ is proportional to its active area. SEM analyses show that M-B particles are dispersed on γ-Al₂O₃ surface, which reduces the agglomeration of M-B and increases the active surface of M-B/γ-Al₂O₃, leading to a high catalytic activity. A possible mechanism is proposed, which shows that the dissociation of water molecules on γ-Al₂O₃ surface and the microgalvanic interaction between M-B and Al can promote the hydration process of passive oxide film on Al particle surface, speeding up the Al-water reaction.     

Co@Ru nanoparticle with core–shell structure supported over γ-Al2O3 for Fischer–Tropsch synthesis

Co@Ru/γ-Al₂O₃ core–shell structure catalysts with Co/Ru different weight ratios are successfully prepared via surface displacement reaction. This novel route including reduction of Co core by NaBH₄ on the surface of γ-Al₂O₃ and then substitution of Co species with Ru species, the resultant of reduction of RuCl₃ precursor with N₂H₄. These catalysts are characterized with techniques X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDX), high resolution transmission electron microscopy (HRTEM), N₂ adsorption/desorption (BET), temperature programmed reduction (TPR), X-ray photoelectron spectroscopy (XPS) and Fourier transform infra-red (FTIR) of CO adsorbed. The characterization results confirm a uniform dispersion of Co@Ru nanoparticles with core–shell structure over γ-Al₂O₃. The core–shell Co@Ru/γ-Al₂O₃ catalysts show the remarkable catalytic activity towards Fischer–Tropsch synthesis (FTS) in comparison with Co/γ-Al₂O₃, which is related to special core–shell structure. These catalysts exhibited excellent abilities in the cases of increasing formation of long-chain hydrocarbons and suppressing selectivity to lighter hydrocarbons.     

Catalytic performances of Ni-based catalysts on supercritical water gasification of phenol solution and coal-gasification wastewater

Activity and stability of the supported Ni-based catalysts for the gasification performances of phenol solution and coal-gasification wastewater in supercritical water were studied in a continuous reactor at 480 °C, 25 MPa and oxygen ratio of 0.2 for 50 h operation. The influences of the supports (γ-Al₂O₃, active carbon (AC) and carbon nanotube (CNT)) on gas yields, gasification efficiencies for phenol solution were investigated, and the loading amount of Ni were optimized. Results showed that the catalytic activity and the stability of the catalysts followed the order of Ni/CNT > Ni/AC > Ni/γ-Al₂O₃. The activity of Ni/AC and Ni/γ-Al₂O₃ decreased after 30 h continuous operation, and there occurred significant leaching of Ni²⁺. For Ni/CNT catalyst, H₂ yield increased obviously when the loading amount of Ni lower than 15 wt%, while increased little at higher loading amount. Then, 15 wt% Ni/CNT with a thickness of 1.5 mm was coated on 316 L stainless steel (SS316L, an economic material usually used as the reactor material), which can act as a "catalytic tube wall" in reactor. The catalytic activity and corrosion resistance of Ni/CNT/SS316L for the gasification of real coal-gasification wastewater were studied. Results showed that Ni/CNT/SS316L gave a great positive effect on H₂ production. H₂ yield increased from 25.36 mmol/g (total organic carbon) without catalyst to 75.12 mmol/g (total organic carbon) with Ni/CNT/SS316L after operated for 20 h, respectively. However, obvious pealing of the coating was found after 50 h operation. Further study is necessary for the improvement of the coating preparation method.     

Room temperature hydrogen generation from aqueous ammonia-borane using noble metal nano-clusters as highly active catalysts

Nano-clusters of noble metals Ru, Rh, Pd, Pt and Au have been supported on γ-Al₂O₃, C and SiO₂, of which the catalytic activities have been investigated for hydrolysis of NH₃BH₃. Among these catalysts, the Ru, Rh and Pt catalysts exhibit high activities to generate stoichiometric amount of hydrogen with fast kinetics, whereas the Pd and Au catalysts are less active. Support effect has been studied by testing the hydrogen generation reaction in the presence of Pt supported on γ-Al₂O₃, VULCAN^® carbon and SiO₂, and it is found that Pt on γ-Al₂O₃, which has the smallest particle size, is the most active. Concentration dependence of the hydrogen generation from aqueous NH₃BH₃ solutions has been investigated in the presence of Pt/γ-Al₂O₃ by keeping the amount of Pt/γ-Al₂O₃ catalyst unchanged, which exhibits that the hydrogen release versus time (ml H₂ min⁻¹) does not significantly change with increasing the NH₃BH₃ concentration, indicating that the hydrogen release rate is not dependent on the NH₃BH₃ concentration and the high activity of the Pt catalyst can be kept at high NH₃BH₃ concentrations. Activation energies have been measured to be 23, 21 and 21 kJ mol⁻¹ for Ru/γ-Al₂O₃, Rh/γ-Al₂O₃ and Pt/γ-Al₂O₃ catalysts, respectively, which may correspond to the step of B–N bond breaking on the metal surfaces. The particle sizes, surface morphology and surface areas of the catalysts have been obtained by TEM and BET experiments.     

Effect of CaO–ZrO2 addition to Ni supported on γ-Al2O3 by sequential impregnation in steam methane reforming

Ni catalysts supported on (CaO–ZrO₂)-modified γ-Al₂O₃ were prepared by sequential impregnation. The effects of varied CaO to ZrO₂ mole ratios at 0, 0.20, 0.35, 0.45, and 0.55 on the activity and stability of the modified Ni catalysts were studied. As a result of using CaO–ZrO₂ as a promoter, each catalyst contained CaO–ZrO₂ at only 5%. γ-Al₂O₃ used as support was modified by CaO–ZrO₂ before the deposition of nickel oxide. The addition of CaO–ZrO₂ at an optimum ratio was expected to improve the stability of Ni catalysts due to the decrease of carbon formation resulting from carbon gasification. All the fresh catalysts were characterized by ICP, XRD, BET surface area, TGA in H₂, and TPR before catalytic testing in steam methane reforming at 600 °C. The spent catalysts were examined by TEM and TGA to observe the catalysts deactivation. The identification of CaO–ZrO₂ phases indicated that CaO and ZrO₂ reacted with each other to be monoclinic solid solution ZrO₂, CaZr₄O₉, CaZrO₃, and CaO corresponding to the phase diagram of CaO–ZrO₂. The existence of CaZrO₃ for 0.55 mol ratio of CaO/ZrO₂ enhanced activity in steam methane reforming because oxygen vacancies in CaZrO₃ greatly preferred the water adsorption creating the favorable conditions for carbon gasification and, then, water gas shift. The prominence and continued existence of these two reactions on the Ni catalysts leads to the particular increase of H₂ yield. Moreover, the increasing amount of CaZrO₃ in the Ni catalysts significantly improved carbon gasification. However, the Ni catalysts with CaZrO₃ showed whisker carbon after catalytic testing; this carbon specie has not been tolerated in steam methane reforming. Therefore, these results significantly differed from the hypothesis.     

Behavior of nickel catalysts in supercritical water gasification of glucose: Influence of support

The catalytic performance of Ni-based supercritical water gasification (SCWG) catalysts may be influenced strongly by the nature of support. In this paper, Ni catalysts with the different supports (CeO₂/Al₂O₃, La₂O₃/Al₂O₃, MgO/Al₂O₃, ZrO₂/Al₂O₃) were prepared by two-step impregnation method. The fresh and used catalysts were characterized by X-ray diffraction patterns (XRD), scanning electron microscopy with an Energy Dispersive X-ray (SEM-EDX), Brunauer–Emmett–Teller (BET) specific surface area measurements, X-ray photoelectron spectroscopy (XPS) and Thermo-gravimetric analyses (TGA). The catalyst performance testing was conducted by SCWG of glucose at 673 K and 23.5 MPa with an autoclave reactor, to evaluate the influence of support on the hydrogen production. The results showed that H₂ yield for different supports decreased in order: CeO₂/Al₂O₃ > La₂O₃/Al₂O₃ > MgO/Al₂O₃ > Al₂O₃ > ZrO₂/Al₂O₃, and H₂ selectivity decreased in order: CeO₂/Al₂O₃ > La₂O₃/Al₂O₃ > ZrO₂/Al₂O₃ > Al₂O₃ > MgO/Al₂O₃. Ni catalysts were deactivated in SCWG reaction because of sintering and coke deposition. Compared with other supports, CeO₂ can be used as the promoter of carbon removal from catalyst surfaces.