共查询到20条相似文献,搜索用时 93 毫秒
1.
《电子器件》1982,(1)
如上所述,整管结构示意图见签201。 后加速会聚透镜以下简称PDAL(post Dafleclion Aleeleration Lens) 为了研究方便,电子枪偏转板中心电压与阳极同电位,即没有辅助聚焦,电子枪阳极,编转板中心及PDAL低压电极①同电位为(?)A。PDAL电极②为调正电极,电位(?)J可调,PDAL电极③为高压电极,与屏同电位,电位UA2。电子枪的聚焦电压力VF。 一般电子束管中,电子束在发射系统中交叉,将此交叉截面作为聚焦透镜物。在屏上得到它的象,即光点。但是在本结构中,电子束在偏转系统出口处再次交叉,形成虚象,然后通过PDAL在屏上得到实象——光点。因此这是二次交叉类型管种。光学系统见签202。 相似文献
2.
电子束管是电真空器件的一种,它通常由抽成真空的玻壳及封入其中的电子枪构成。作为管芯的电子枪是电子束管的心脏,无论是那种类型的电子束管都缺少不了电子枪。电子枪是由阴极发射透镜、预聚焦透镜、主聚焦透镜、偏转棱镜等一系列电子透镜依次组合装配而成的电子光学系统。轴对称静电式电子透镜,均是由馈以不同直流电压的圆筒型电极零件按不同间隙装架而成。除掉阴极、调制极外,各个 相似文献
3.
4.
引言众所周知,在一列式彩色CRT中使用了自会聚系统,其偏转线圈引起了很大的象散,这种象散大大减弱了屏边缘的分辨率。近来,做了一些尝试以校正这种象散,即在电子枪中使用一种具有双电位主透镜系统的聚焦电极的四极透镜。在四极透镜上加上一个与束偏转同步的动态电压,以补偿由于偏转系统引起的象散。这种动态电压也可以在整个屏上使电子束聚焦,即能够实现动态聚焦。 相似文献
5.
6.
7.
本文对日立公司新一代彩色显像管用电子枪的结构及性能进行了剖析和系统讨论。其超大椭圆孔的主透镜使有效直径比上一代电子枪提高了25%,电子束形成区实现最优化设计,不同电流下聚焦的稳定性提高,同时进入主透镜的电子束发散角在水平和垂直方向不同,实现与主透镜的最佳配合,充分发挥了主透镜中共同透镜为椭圆孔透镜的特点。聚焦对比实验也显示出日立公司新一代电子枪聚焦的优异性能。 相似文献
8.
9.
研制一种高亮度细束可拆卸电子枪。电子束工作电压10kV,总束流100300A。在采用直径20m的圆形或2020m2的方形物孔限制光阑时,通过物孔光阑的束流是12A,束角为510-3。对电子枪的结构作了介绍,对阴极灯丝、阳极头、物孔光阑等的制造和组装也作了说明。枪外径特别小,只有17mm,可用于大屏幕油膜光阀、热塑记录等需要动态真空系统的场合。 相似文献
10.
11.
本文提出了示波管偏转系统高频性能分析新方法。通过分析电子在偏转系统内的渡越时间差模型,导出偏转系统在单位阶跃电压函数作用下,电子束扫描轨迹方程及上升时间的计算。 相似文献
12.
13.
14.
本文提出了计算慢波偏转系统中电位分布、电子轨迹、偏转参量的方法。电位分布在数值计算的基础上,以解析表达式近似。计算结果与实际管子的特性很好地吻合,表明本方法适用于工程设计。 相似文献
15.
提出了一种检测三维磁场的真空微电子磁敏传感器。该传感器采用Spindt阴极阵列作为电子源,阳极分为五个区域,以便检测发射电子在磁场作用下的偏移。通过不同阴极电压下电子束流的偏移量的国赤出器件所在位置磁场的三个分量。对传感器的灵敏度和误差进行了模拟计算,并研究了它们与阳极电压、阴-阳极间距及阳极电压变化步长的关系。结果表明该传感器的灵敏度约为800%,相对误差为3%。 相似文献
16.
电子束静电折板偏转系统研究 总被引:2,自引:2,他引:0
以SDS-3电子束曝光机为基础,用折板结构静电偏转替代直板结构静电偏转,探讨了电子束曝光机折板静电偏转场的电子轨迹与电位分布应满足的要求。导出了折板静电偏转灵敏度与电位分布之间的关系,给出静电偏转像差方程及像差系数。用矢量描写电子轨迹,以积分式表示像差系数,给出了折板结构方程与参量。像差系数适应计算机辅助运算。结果表明,折板结构静电偏完成的图像像差明显优于原直板结构静电偏。提供了静电折板偏转与直板偏转的相关计算数据及摩尔栅条纹图。 相似文献
17.
本文提出了螺旋形慢波线最佳带宽时的相速与电子速度之间的数量关系;指出偏转灵敏度最高时的加速电压并不是同步电压。 相似文献
18.
《Electron Devices, IEEE Transactions on》1962,9(5):399-404
A demagnification gun of high resolution was developed for thermoplastic recording by deflecting the electron beam at the entry of a large focusing lens. The unconventional approach of prefocus deflection allows close spacing between the "short" focusing lens and the target (phosphor screen or thermoplastic tape) required for demagnification and results in a gun with a relatively short length. The diameter of the focusing lens is about three times larger than the 25-mm diameter area to be scanned in order to keep spot distortions of the deflected beam at a minimum. Electrostatic focusing combined with magnetic deflection was selected. The special focusing lens that is used is shaped for low aberrations, increased demagnification and increased deflection sensitivity. Small deflection fields are required since the electron beam is being deflected in the accelerating field while the electron velocities are still low. The gun operates at 10 kv and delivers a 5-micron spot at 1µa. This corresponds to a resolution of 5000 spot diameters at average current densities in excess of 5 amp/cm2. In spite of the high resolution, the over-all length of the gun measured from the target is only 9 inches. 相似文献
19.
《Electron Devices, IEEE Transactions on》1962,9(2):197-203
In a television receiver the horizontal deflection is of critical importance because of the high deflection power. Recently various proposals have been published, according to which the electron beam is to be deflected over a small angle only, in order to diminish the deflection power. Subsequently this small deflection angle is to be increased by an electrostatic or magnetic lens. In the present paper, it is shown with the aid of general laws of electron optics that such a scan magnification by an electrostatic or magnetic lens necessarily causes a decrease of the resolution, and thereby, of the quality of the television picture, unless known possibilities of increasing the resolution are employed simultaneously. The calculation also affirms that with magnetic deflection, unlike electrostatic deflection, post-acceleration does not lead to a significant reduction in deflection power with unchanged resolution. 相似文献
20.
This paper discusses the general deflection system calibration problem that occurs in electron beam lithography and metrology systems.These systems generally have an X, Y stage whose position can be measured, but not set to a high degree of accuracy.The calibration problem involves aligning the coordinate system associated with electron beam deflection system to that of the X, Y stage, and measuring the deflection system sensitivity.Current commercially available examples of these systems include the Cambridge Instruments EBMF-6 electron beam lithography system and the EBMT-5 electron beam metrology system. 相似文献