聚氨酯软骨-骨双层复合材料的构建及性能研究

关节软骨损伤是临床上的常见病,由于其组织再生能力差,可能导致骨性关节炎的发生,因此,研究开发骨-软骨移植替代材料非常重要。目的就是设计一体化软骨-骨双层复合材料,以解决软骨与骨的整合问题。该双层复合体上层软骨材料为聚氨酯,软骨下骨为羟基磷灰石/聚氨酯复合支架材料,两层结构中引用了同一种材料——聚氨酯,将双层结构有机黏合在一起,使黏合更牢固。下层多孔HA/PU复合支架材料的孔与孔之间相互贯通,孔隙率约为83%,孔径范围分布在200～600μm。体外细胞相容性实验表明,该一体化双层复合材料为细胞的黏附、增殖以及生存活力的维持提供了有利环境。上述结果表明该双层复合材料有望用于软骨组织工程修复。     

纳米羟基磷灰石/聚酰胺多孔支架材料的制备及性能研究

使用多种致孔剂采用粒子沥滤法制备了纳米羟基磷灰石／聚酰胺多孔支架材料，用IR、XRD、SEM等手段对多孔复合材料的组成结构及形貌进行了表征，并检测了其物理性能指标。结果表明，复合材料中两相分散均匀，且发生了界面结合；材料的孔隙率与致孔剂的含量成正比，支架中大孔与微孔并存且相互贯通；以NaCl作致孔剂且孔隙率达到80％左右时的支架材料可以同时满足组织工程对孔隙率和力学强度的双重要求。     

脂肪族聚氨酯/磷灰石复合材料的原位制备及性能

为避免芳香族聚氨酯在体内降解时产生有毒物质,选用生物相容性良好的脂肪族聚氨酯(PU)与生物活性的羟基磷灰石(HA)为原料,通过原位聚合法制备了脂肪族PU/HA组织工程用多孔支架,并采用SEM、IR和力学试验等方法对多孔支架的形貌和性能进行了表征,进一步研究了发泡剂(水)用量和HA含量对支架泡孔结构和力学强度的影响。结果表明,当发泡剂用量为1%～1.5%(质量分数)时制得的多孔PU/HA复合支架材料孔隙之间相互贯通,孔径范围分布在300～800μm,大孔壁上分布着孔径为50～200μm的小孔,孔隙率达80%以上。随HA含量增加,支架抗压强度和弹性模量显著上升。综合考虑HA的增强效果和组织工程支架的孔隙结构,本体系中HA的最佳添加量为40%(质量分数),发泡剂的最佳用量为1%(质量分数)。     

注射成型羟基磷灰石/聚酰胺6多孔支架的微观结构和力学性能

采用注射成型法制备了羟基磷灰石/聚酰胺6(HA/PA6)多孔支架,用SEM、XRD、DSC等手段表征了支架的组成结构和形貌,检测了其力学性能.研究表明,调节羟基磷灰石(HA)含量、偶氮二甲酰胺(AC)用量和预塑量能有效控制支架的力学性能、孔径大小和孔隙率.HA/PA6支架的孔径在100～500μm左右,孔隙率达到甚至超...     

注射参数和组分对羟基磷灰石／聚酰胺66多孔支架结构和性能的影响

采用注射成型法制备了羟基磷灰石／聚酰胺66（HA／PA66）多孔支架,用SEM、XRD和DSC等手段表征了支架的形貌和结构,测试了其力学性能。研究表明,调节注射参数（发泡剂和储料量）能控制支架的力学性能、孔径大小和孔隙率。HA能提高支架的刚性,但使孔径和孔隙率下降。在HA／PA66（30／70,质量比）中添加乙烯一醋酸...     

有机泡沫法制备多孔羟基磷灰石生物支架

采用有机泡沫法制备了多孔羟基磷灰石(HA)支架,考察了水解预处理工艺、粘结剂聚乙烯醇(PVA)和固相HA的含量对孔隙率的影响,利用扫描电子显微镜(SEM)观察了支架的孔结构.研究结果表明,采用有机泡沫法可获得孔径均匀的多孔HA支架;有机泡沫(海绵)模板经过水解处理后,其挂浆量增加;支架的孔隙率随PVA含量的增加而增大;浆料中固相HA含量在70%左右为宜,此时材料的孔隙率最大.     

纳米磷灰石晶体/聚酰胺复合骨组织工程支架材料的研究

采用常压共溶、共沉淀和水热处理的方法制备了纳米磷灰石晶体／聚酰胺复合骨组织工程支架材料。纳米磷灰石在复合材料中含量高达60wt％(重量比),纳米磷灰石和聚酰胺之间有化学键结合,材料的力学性能接近自然骨水平。复合材料可加工成块状多孔体,材料的孔隙率为55％-70％,平均孔径为300μm,多孔支架不仅有大孔,而且大孔壁上含有丰富微孔,是一种非常有发展前景的组织工程材料。     

孔结构渐变聚己内酯/羟基磷灰石仿生骨材料

为获得具有类似人骨的渐变孔结构、力学性能良好的羟基磷灰石(hydroxyapatite,HA)/聚己内酯(polycaprolactone,PCL)仿生骨材料,采用水热法制备了HA粉末,通过溶剂共混法将其与PCL复合,并采用浇铸/NaCl微粒浸出法制备了多孔状HA/PCL复合材料.通过控制造孔剂NaCl的粒径和用量得到了不同孔径、不同孔隙率的HA/PCL复合材料及具有渐变孔结构的HA/PCL复合材料.利用光学显微镜观察了其孔结构,结果为孔径在100～300μm,最大孔隙率达到80%.同时研究了它们在人体体温附近(37±5)℃的力学性能,结果表明渐变孔结构的HA/PCL复合材料的力学性能较单一孔结构的HA/PCL复合材料有了很大的提高.通过梯度造孔不仅可获得与人骨极为类似的多孔仿生材料,同时还可大幅提高多孔材料的力学性能.     

纳米羟基磷灰石/聚合物多孔复合支架材料

为提高骨组织工程支架材料的力学性能,改善其生物活性,综合天然与合成高分子的优点,采用溶液共混相分离法制备出聚己内酯(PCL)-壳聚糖(CS)多孔支架材料, 并进一步采用离心注浆法填充具有生物活性的纳米羟基磷灰石(HA)-聚乙烯醇(PVA)复合浆料, 制备了n-HA-PVA/PCL-CS复合多孔支架材料, 改善了PCL-CS支架材料力学性能。采用扫描电子显微镜、红外光谱、元素分析、孔隙率和抗压强度试验对材料进行了表征。结果表明, PCL-CS支架材料的内部具有蜂窝状的相互贯通的孔隙结构,孔隙率可以达到60%～80%。CS含量越大,孔隙率越大,而抗压强度越小。填充后的n-HA-PVA/PCL-CS复合多孔支架材料,孔隙率有所下降,但仍大于60%,而其弹性模量可提高至25.71 MPa。      

β-磷酸三钙/聚L-乳酸与大鼠骨膜成骨细胞复合骨修复材料的研究

采用溶液浇铸-模压成型-沥滤方法制备了β-TCP/PLLA多孔支架材料, 将支架材料与大鼠骨膜成骨细胞复合获得新型组织工程骨修复材料. 通过抗压强度及压缩模量的表征研究了支架材料的力学性能; 采用SEM观测、MTT法、碱性磷酸酶活性及骨钙素分泌量检测细胞复合材料的体外成骨特性; 通过裸鼠肌袋种植, 以组织学方法评价细胞复合材料的异位成骨能力. 结果表明: β-TCP/PLLA多孔支架材料孔隙率可调, 孔径为100～00μm, 孔道相互贯通; 材料抗压强度和压缩模量随孔隙率的增大而降低, β-TCP复合PLLA后材料的力学性能高于同孔隙率的纯PLLA多孔材料; 复合支架材料适宜骨膜成骨细胞粘附和生长, 无细胞毒性; 骨膜成骨细胞复合β-TCP/PLLA支架材料的体外成骨特性良好, 且具有体内异位成骨能力.     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from     

CNAS Passes APLAC's PTP Review

正The review group of Asia Pacific Laboratory Accreditation Cooperation(APLAC)carried out a 4-day peer review of the proficiency testing provider(PTP)for China National Accreditation Service for Conformity Assessment(CNAS)from July 28 to 31,2014.CNAS passed the PTP review with excellent performance.Two senior peer reviewers of APLAC made a comprehensive,rigorous and detailed review of CNAS’s PTP accreditation activities,and made the on-spot inspection of the review groups in Shanghai and Shenzhen respectively.