A single-chip dual-band direct-conversion IEEE 802.11a/b/g WLAN transceiver in 0.18-/spl mu/m CMOS

This paper presents a single-chip dual-band CMOS direct-conversion transceiver fully compliant with the IEEE 802.11a/b/g standards. Operating in the frequency ranges of 2.412-2.484 GHz and 4.92-5.805 GHz (including the Japanese band), the fractional-N PLL based frequency synthesizer achieves an integrated (10 kHz-10 MHz) phase noise of 0.54/spl deg//1.1/spl deg/ for 2/5-GHz band. The transmitter error vector magnitude (EVM) is -36/-33 dB with an output power level higher than -3/-5dBm and the receiver sensitivity is -75/-74 dBm for 2/5-GHz band for 64QAM at 54 Mb/s.     

A 5-GHz direct-conversion CMOS transceiver utilizing automatic frequency control for the IEEE 802.11a wireless LAN standard

A fully integrated CMOS direct-conversion 5-GHz transceiver with automatic frequency control is implemented in a 0.18-/spl mu/m digital CMOS process and housed in an LPCC-48 package. This chip, along with a companion baseband chip, provides a complete 802.11a solution The transceiver consumes 150 mW in receive mode and 380 mW in transmit mode while transmitting +15-dBm output power. The receiver achieves a sensitivity of better than -93.7dBm and -73.9dBm for 6 Mb/s and 54 Mb/s, respectively (even using hard-decision decoding). The transceiver achieves a 4-dB receive noise figure and a +23-dBm transmitter saturated output power. The transmitter also achieves a transmit error vector magnitude of -33 dB. The IC occupies a total die area of 11.7 mm/sup 2/ and is packaged in a 48-pin LPCC package. The chip passes better than /spl plusmn/2.5-kV ESD performance. Various integrated self-contained or system-level calibration capabilities allow for high performance and high yield.     

一种应用于IEEE 802.11 b/g/n无线局域网收发机的CMOS模拟基带电路

本文提出了一种应用于直接变频无线局域网收发机的模拟基带电路,该电路采用标准的0.13微米CMOS工艺实现,包括了采用有源RC方式实现的接收4阶椭圆低通滤波器、发射3阶切比雪夫低通滤波器、包含直流失调消除伺服环路的接收可变增益放大器及片上输出缓冲器。芯片面积共1.26平方毫米。接收基带链路增益可在-11dB至49dB间以2dB步长调节。相应地,基带接收输入等效噪声电压（IRN）在50 nV/sqrt(Hz) 至30.2 nV/ sqrt(Hz)间变化而带内输入三阶交调（IIP3）在21dBm至-41dBm间变化。接收及发射低通滤波器的转折频率可在5MHz、10MHz及20MHz之间选择以符合包含802.11b/g/n的多种标准的要求。接收基带I、Q两路的增益可在-1.6dB至0.9dB之间以0.1dB的步长分别调节以实现发射IQ增益失调校正。通过采用基于相同积分器的椭圆滤波器综合技术及作用于电容阵列的全局补偿技术,接收滤波器的功耗显著降低。工作于1.2V电源电压时,整个芯片的基带接收及发射链路分别消耗26.8mA及8mA电流。     

A single-chip CMOS transceiver for 802.11a/b/g wireless LANs

A dual-band trimode radio fully compliant with the IEEE 802.11a, b, and g standards is implemented in a 0.18-/spl mu/m CMOS process and packaged in a 48-pin QFN package. The transceiver achieves a receiver noise figure of 4.9/5.6 dB for the 2.4-GHz/5-GHz bands, respectively, and a transmit error vector magnitude (EVM) of 2.5% for both bands. The transmit output power is digitally controlled, allowing per-packet power control as required by the forthcoming 802.11 h standard. A quadrature accuracy of 0.3/spl deg/ in phase and 0.05 dB in amplitude is achieved through careful analysis and design of the I/Q generation parts of the local oscillator. The local oscillators achieve a total integrated phase noise of better than -34 dBc. Compatibility with multiple baseband chips is ensured by flexible interfaces toward the A/D and D/A converters, as well as a calibration scheme not requiring any baseband support. The chip passes /spl plusmn/2 kV human body model ESD testing on all pins, including the RF pins. The total die area is 12 mm/sup 2/. The power consumption is 207 mW in the receive mode and 247 mW in the transmit mode using a 1.8-V supply.     

A low voltage CMOS RF front-end for IEEE 802.11b WLAN transceiver

A low voltage CMOS RF front-end for IEEE 802.11b WLAN transceiver is presented. The problems to implement the low voltage design and the on-chip input/output impedance matching are considered, and some improved circuits are presented to overcome the problems. Especially, a single-end input, differential output double balanced mixer with an on-chip bias loop is analyzed in detail to show its advantages over other mixers. The transceiver RF front-end has been implemented in 0.18 um CMOS process, the measured results show that the Rx front-end achieves 5.23 dB noise figure, 12.7 dB power gain (50 ohm load), −18 dBm input 1 dB compression point (ICP) and −7 dBm IIP3, and the Tx front-end could output +2.1 dBm power into 50 ohm load with 23.8 dB power gain. The transceiver RF front-end draws 13.6 mA current from a supply voltage of 1.8 V in receive mode and 27.6 mA current in transmit mode. The transceiver RF front-end could satisfy the performance requirements of IEEE802.11b WLAN standard. Supported by the National Natural Science Foundation of China, No. 90407006 and No. 60475018.     

A single-chip dual-band tri-mode CMOS transceiver for IEEE 802.11a/b/g wireless LAN

A single-chip dual-band tri-mode CMOS transceiver that implements the RF and analog front-end for an IEEE 802.11a/b/g wireless LAN is described. The chip is implemented in a 0.25-/spl mu/m CMOS technology and occupies a total silicon area of 23 mm/sup 2/. The IC transmits 9 dBm/8 dBm error vector magnitude (EVM)-compliant output power for a 64-QAM OFDM signal. The overall receiver noise figure is 5.5/4.5 dB at 5 GHz/2.4 GHz. The phase noise is -105 dBc/Hz at a 10-kHz offset and the spurs are below -64 dBc when measured at the 5-GHz transmitter output.     

A 2.4-GHz 0.25-/spl mu/m CMOS dual-mode direct-conversion transceiver for bluetooth and 802.11b

A dual-mode transceiver integrates the transmitter of 0-dBm output power and the receiver for both Bluetooth with -87 dBm sensitivity and 802.11b with -86 dBm sensitivity in a single chip. A direct-conversion architecture enables the maximum reuse and the optimal current consumption of the various building blocks in each mode for a low-cost and low-power solution. A single-ended power-amplifer (PA) driver transmits the nominal output power of 0 dBm with 18-dB gain control in 3-dB steps. Only little area overhead is required in the baseband active filter and programmable gain amplifier (PGA) to provide the dual-mode capability with optimized current consumption. The DC-offset cancellation scheme coupled with PGAs implements the very low high-pass cutoff frequency with a smaller area than required by a simple coupling capacitor. Fabricated in 0.25-/spl mu/m CMOS process, the die area is 8.4 mm/sup 2/ including pads, and current consumption in RX is 50 mA for Bluetooth and 65 mA for 802.11b from a 2.7-V supply.     

An auto-I/Q calibrated CMOS transceiver for 802.11g

The CMOS transceiver IC exploits the superheterodyne architecture to implement a low-cost RF front-end with an auto-I/Q calibration function for IEEE 802.11g. The transceiver supports I/Q gain and phase mismatch auto tuning mechanisms at both the transmitting and receiving ends, which are able to reduce the phase mismatch to within 1/spl deg/ and gain mismatch to 0.1dB. Implemented in a 0.25 /spl mu/m CMOS process with 2.7 V supply voltage, the transceiver delivers a 5.1 dB receiver cascade noise figure, 7 dBm transmit, and a 1 dB compression point.     

A low-power monolithic CMOS transceiver for 802.11b wireless LANs

A single-chip low-power transceiver IC operating in the 2.4 GHz ISM band is presented. Designed in 0.18 μm CMOS, the transceiver system employs direct-conversion architecture for both the receiver and transmitter to realize a fully integrated wireless LAN product. A sigma-delta (∑△) fractional-N frequency synthesizer provides on-chip quadrature local oscillator frequency. Measurement results show that the receiver achieves a maximum gain of 81 dB and a noise figure of 8.2 dB, the transmitter has maximum output power of-3.4 dBm and RMS EVM of 6.8%. Power dissipation of the transceiver is 74 mW in the receiving mode and 81 mW in the transmitting mode under a supply voltage of 1.8 V, including 30 mW consumed by the frequency synthesizer. The total chip area with pads is 2.7×4.2 mm2.     

支持WAPI协议的802.11a/b/g WLAN芯片

本文介绍了中国国家无线局域网标准中的WAPI安全体系结构,同时介绍了支持该标准的USB2.0接口无线局域网网卡芯片设计,特别是其中安全协议部分.测试结果表明,该芯片可以实现中国国家无线局域网标准规定的各项要求,性能优异.     

A Low-Power Fullband 802.11a/b/g WLAN Transceiver With On-Chip PA

A low-power fullband 802.11a/b/g WLAN transceiver in 0.15-mum CMOS technology is described. The zero-IF transceiver achieves a receiver noise figure of 4.4/4 dB for the 2.4-GHz/5-GHz bands, respectively. The corresponding sensitivity at 54-Mb/s operation is -72 dBm for 802.11g and -74 dBm for 802.11a using actual PER measurement. An on-chip PA delivers 20 dBm output P1-dB. A new I/Q compensation scheme is implemented in local oscillator (LO) and an image rejection of better than 52 dB is observed. The transmitter delivers 10/1.5 dBm (2.4-/5-GHz) EVM-compliant output power for a 64-QAM OFDM signal at 54-Mb/s. The power consumption is 117/135 mW (1.8-V) in the receive mode and 570/233.1 mW in the transmit mode for 2.4/5 GHz, respectively. The low power consumption, high integration and robustness (-40 to 140degC) make this transceiver suitable for portable applications     

A fully integrated CMOS direct-conversion transmitter front-end for WiMAX

A naturally commutated six-pulse cycloconverter working in the inverting mode is used to feed power to a single phase AC motor at 400 Hz. The motor is connected at the input side of the cycloconverter while the three-phase mains is connected at its output. Three-phase mains feeds power to the input side of the cycloconverter which is arranged as a tuned load at 400 Hz. The effect of the single-phase induction motor on system performance is discussed. The principle of voltage and frequency control for proper operation of the induction motor is presented. The results are experimentally verified.     

A World-Band Triple-Mode 802.11a/b/g SOC in 130-nm CMOS

A fully integrated system-on-a-chip (SOC) in 130-nm CMOS technology compliant with world-band 802.11a/b/g is presented. This SOC integrates all blocks including 2.4-GHz/5-GHz RF tranceiver, baseband physical layer (PHY), and the medium access controller (MAC). At 1.8 V, the whole SOC dissipates 144/168 mA in receiving mode and 114/150 mA in transmitting mode for 2.4-GHz/5-GHz-band operations. The measured receiver sensitivity at 2.4 GHz/5 GHz is $-{hbox{77.5}}/-{hbox{74}} hbox{dBm}$ at 54 Mb/s rate, and the transmitter EVM at 54 Mb/s rate is $-{hbox{33}}/-{hbox{30}} {hbox {dB}}$ at an output power of $-{hbox{7}}/-{hbox{8}} hbox{dBm}$. By integrating multiple on-chip LDOs with no off-chip capacitors, this SOC features the capability of being directly supplied by off-chip switching-type DC/DC converter without performance degradation.      

适用于零中频802.11a/b/g无线局域网以及蓝牙系统的工作在8.64-11.62GHz的压控振荡器和分频器

本文提出了工作在1.2V电压下用0.13um工艺实现的全集成压控振荡器和分频器。压控振荡器的工作频段是8.64GHz到11.62GHz,可以通过2分频产生适用于802.11a无线局域网（5.8GHz频段）的正交本振信号,通过4分频产生适用于802.11b/g无线局域网和蓝牙协议（2.4GHz频段）的正交本振信号。6位开关电容阵列用来调整所需要的工作频段。测试结果显示压控振荡器2分频后在距离5.5G载波1M频偏处的相位噪声是-113dBc,压控振荡器消耗了3.72mW的功耗,FOMT 是-192.6dBc/Hz。     

8.64-11.62 GHz CMOS VCO and divider in a zero-IF 802.11a/b/g WLAN and Bluetooth application

A fully integrated VCO and divider implemented in SMIC 0.13-μm RFCMOS 1P8M technology with a 1.2 V supply voltage is presented.The frequency of the VCO is tuning from 8.64 to 11.62 GHz while the quadrature LO signals for 802.11a WLAN in 5.8 GHz band or for 802.11b/g WLAN and Bluetooth in 2.4 GHz band can be obtained by a frequency division by 2 or 4,respectively.A 6 bit switched capacitor array is applied for precise tuning of all necessary frequency bands.The testing results show that the VCO has a phas...     

用于IEEE802．11b／g WLAN直接下变频接收机的射频前端设计

介绍了一种应用于IEEE802．11b／g无线局域网接收机射频前端的设计。基于直接下变频的系统架构。接收机集成了低噪声放大器、I／Q下变频器、去直流偏移滤波器、基带放大器和信道选择滤波器。电路采用TSMC0．18μm CMOS工艺设计,工作在2．4GHz ISM（工业、科学和医疗）频段,实现的低噪声放大器噪声系数为0．84dB,增益为16dB,S11低于-15dB,功耗为13mW;I／Q下变频器电压增益为2dB,输入1dB压缩点为-1 dBm,噪声系数为13dB,功耗低于10mw。整个接收机射频前端仿真得到的噪声系数为3．5dB,IIP3为-8dBm,IP2大于30dBm,电压增益为31dB,功耗为32mW。     

A continuous-time delta-sigma modulator for 802.11a/b/g WLAN implemented with a hierarchical bottom-up optimization methodology

This paper presents a 3rd-order continuous-time Delta-Sigma modulator with a resolution of 10 bits for a 10 MHz signal bandwidth. It is designed in a standard 0.18 μm CMOS technology and consumes only 6 mW. After the design/selection of the topologies for the integrators, comparator and D/A converters, optimal sizing of the complete modulator was ensured by using a hierarchical bottom-up, multi-objective evolutionary design methodology. With this methodology, a set of Pareto-optimal modulator designs is generated by using Pareto-optimal performance solutions of the hierarchically decomposed lower-level subblocks. From the generated Pareto-optimal design set, a final optimal design is chosen that complies with the specifications for the 802.11a/b/g WLAN standard and has minimal power consumption.     

A low-power high-performance SiGe BiCMOS 802.11a/b/g transceiver IC for cellular and bluetooth Co-existence applications

This paper describes a high-performance WLAN 802.11a/b/g radio transceiver, optimized for low-power in mobile applications, and for co-existence with cellular and Bluetooth systems in the same terminal. The direct-conversion transceiver architecture is optimized in each mode for low-power operation without compromising the challenging RF performance targets. A key transceiver requirement is a sensitivity of -77 dBm (at the LNA input) in 54 Mb/s OFDM mode while in the presence of a GSM1900 transmitter interferer. The receiver chain achieves an overall noise figure of 2.8/3.2 dB, consuming 168/185 mW at 2.8 V for the 2.4/5GHz bands, respectively. Signal loopback and transmit power detection techniques are used in conjunction with the baseband modem processor to calibrate the transmitter LO leakage and the transceiver I/Q imbalances. Fabricated in a 70 GHz f/sub T/ 0.25-/spl mu/m SiGe BiCMOS technology for system-in-package (SiP) use, the dual-band, tri-mode transceiver occupies only 4.6 mm/sup 2/.     

用于IEEE 802.11 b/g/n WLAN的高线性度功率放大器

基于2μm的InGaP/GaAs异质结双极晶体管(HBT)工艺设计了一种可应用于IEEE802.11 b/g/n无线局域网(WLAN)的高线性度射频功率放大器.为了提高射频功率放大器的线性度,采用了负反馈镜像电路提供直流工作点,设计了良好的输入、输出和级间匹配电路来提高射频功率放大器的线性输出功率.流片结果表明,在工作电压为3.3V时,射频功率放大器的1 dB线性压缩输出功率(P1dB)可达27 dBm,当误差向量幅度(EVM)为3％时,2.4 GHz64 QAM激励下,输出功率可达19.8 dBm,满足标准规范要求.     

A programmable gain amplifier with a DC offset calibration loop for a direct-conversion WLAN transceiver

A high-linearity PGA (Programmable Gain Amplifier) with DC offset calibration loop is proposed in this paper. The PGA adopts a differential degeneration structure to vary voltage gain and uses the closed-loop structure including the input op-amps to enhance the linearity. A continuous time feedback based DC offset calibration loop is also designed to solve the DC offset problem. This PGA is fabricated in TSMC 0.13um CMOS technology. The measurements show that the receiver PGA （RXPGA）provides 64dB gain range with a step of 1dB, and the transmitter PGA（TXPGA） covers 16dB gain. The RXPGA consumes 18mA and the TXPGA consumes 7mA (I and Q path) under 3.3V supply. The bandwidth of the multi-stage PGA is higher than 20MHz. In addition, the DCOC (DC offset cancellation) circuit shows 10KHz of HPCF (high pass cutoff frequency) and the DCOC settling time is less than 0.45µs.