Investigation of a novel bayonet tube high temperature heat exchanger with inner and outer fins

In this paper, a novel bayonet tube high temperature heat exchanger (HTHE) with inner and outer fins is presented. It can be used in the ultra high temperature environment, such as hydrogen production, very high temperature reactor and externally fired combined cycle. Numerical investigation of heat transfer performance on the inside of bayonet element has been conducted for structure design. The numerical results suggest that the inner fin and inner tube should not be welded together. It is recommended that the air enters from the inner tube and exits from the annular space in the high temperature zone. A high temperature experimental system has been established to test the heat transfer and pressure drop characteristics of the HTHE. The surface area density of the tested HTHE is 6 times higher than that of the bare bayonet tube heat exchanger. The experimental results indicate that the mass flow rate on both sides and inlet temperature on the fuel gas side have a significant effect on the heat transfer rate and effectiveness, while the pressure drop ratios are mainly affected by the mass flow rate rather than the inlet temperature. Comparison between the tested HTHE and the similar HTHE without fins indicates that the proposed HTHE has a significant potential to improve the comprehensive heat transfer performance.     

Dynamics of plate heat exchangers subject to flow variations

A predictive model has been presented to suggest the transient response of plate heat exchangers, subjected to a step flow variation. The work also brings out the effect of the port to channel maldistribution on the performance of plate heat exchangers under the condition of flow variation. The results indicate that flow maldistribution affects the performance of the plate heat exchangers in the transient regime. A wide range of the parametric study has been presented which brings out the effects of NTU and heat capacity rate ratio on the response of the plate heat exchanger, subjected flow perturbation.To verify the presented theoretical model, appropriate experiments have been carried out. Experiments include the responses of the outlet temperatures subjected to inlet temperature transient in the circuit followed by a sudden change in flow rate in one of the fluids. Simulated performance has been compared to the performance measured in the experiments. Comparisons indicate that theoretical model developed for flow transient is capable of predicting the transient performance of the plate heat exchangers satisfactorily, under the given conditions of changed flow rates.     

Theoretical analysis of ammonia-water absorption cycles for refrigeration and space conditioning systems

This paper presents an investigation of an ammonia-water absorption cycle for solar refrigeration, airconditioning and heat pump operations at higher heat supply temperatures. The system consists of a solar driven generator, rectifier, condenser, evaporator, absorber and heat exchangers for preheating and subcooling within the system. A steady state thermodynamic cycle analysis based on mass and heat balances along with the state equations for the thermodynamic properties of the ammonia-water mixture has been carried out. A numerical computer simulation of the system with input component temperatures, refrigerant concentration/mass flow rate and effectiveness of the heat exchangers has been made to evaluate the relative heat transfer rates (i.e. coefficients of performance) and the mass flow rates for the cooling/heating modes. It is found that unlike the low generator temperature behaviour the coefficients of performance for both cooling and heating modes are reduced at higher generator temperatures. However, an increase of condenser temperature for each mode of operation improves the performance of the systems at higher generator temperatures. A choice for keeping the absorber temperature equal to/lower than that of the condenser is also predicted at lower/higher generator temperatures, respectively. In general the results are more pronounced for the refrigeration mode than for the heat pump mode and are least effective for the airconditioning mode.     

Planning the optimum cleaning schedule based on simulation of heat exchangers under fouling

An investigation of variations in outlet temperatures of heat exchangers under fouling was carried out. The simulation of heat exchangers was performed by employing a linear fouling deposit function. The formation of deposits reduces heat exchangers effectiveness. There is inherently a linear nature between outlet and inlet temperatures of heat exchangers. The outlet temperatures can also be affected by up‐stream exchangers serving the same streams, and the up‐stream influence can be transferred in the heat system. The mathematical model of the cleaning cycle was outlined, based on the objective function of minimizing cost in unit operation time. According to the results, some heat exchangers can be given cleaning priority when the system is shut down, in order to maximize economic benefit. © 2011 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley Online Library ( wileyonlinelibrary.com/journal/htj ). DOI 10.1002/htj.20384     

紧凑式两相换热器中管式换热元件沸腾传热实验研究

以烃类物质（丙烷和正戊烷）作为工质,进行了紧凑式换热器中带有加工配置表面的管式换热元件池沸腾实验研究。其中,单管实验温度工况为２５３Ｋ￣２９３Ｋ（饱和工质）。实验中所采用的换热元件为重入式结构加工配置表面的强化传热管和光管以及低助管。针对由４５根光管或带有加工配置表面的管子所构成的叉排管束进行了实验研究,实验工质为丙烷和正戊烷,实验温度分别为两种工质在２６３Ｋ和３０８Ｋ之间的饱和和温度。并将所得实     

Experimental investigations on overall cooling effect of ribbed channel with air bleeds

An experimental investigation on overall heat transfer performance of a rectangular channel, in which one wall has periodically placed oblique ribs to enhance heat exchange and cylindrical film holes to bleed cooling air, has been carried out in a hot wind tunnel at different mainstream temperatures, hot mainstream Reynolds numbers, coolant Reynolds numbers and blowing ratios. To describe the cooling effect of combined external coolant film with the internal heat convection enhanced by the ribs, the overall cooling effectiveness at the surface exposed in the mainstream with high temperature was calculated by the surface temperatures measured with an infrared thermal imaging system. The total mass flow rate of cooling air through the coolant channel was regulated by a digital mass flow rate controller, and the blowing ratio passing through the total film holes was calculated based on the measurements of another digital-type mass flow meter. The detailed distributions of overall cooling effectiveness show distinctive peaks in heat transfer levels near the film holes, remarkable inner convective heat transfer effect over entire channel surface, and visible conductive heat transfer effect through the channel wall; but only when the coolant Reynolds number is large enough, the oblique rib effect can be detected from the overall cooling effectiveness; and the oblique bleeding hole effect shows the more obvious trend with increasing blowing ratios. Based on the experimental data, the overall cooling effectiveness is correlated as the functions of Re_m (Reynolds number of hot mainstream) and Re_c (Reynolds number of internal coolant flow at entrance) for the parametric conditions examined.     

The effect of flow maldistribution on the evaluation of axial dispersion and thermal performance during the single-blow testing of plate heat exchangers

A single-blow transient test technique based on axial dispersion model is proposed for the determination of both heat transfer coefficient and axial dispersion coefficient in plate heat exchangers, characterized by NTU and dispersive Peclet number respectively. The present experimental analysis deals with the effect of flow maldistribution on the transient temperature response for U-type plate heat exchangers. The experiments are carried out with uniform and non-uniform flow distributions for various flow rates and two different numbers of plates. Special effort has been made to differentiate the deviation from plug flow due to flow maldistribution and fluid backmixing. The fluid axial dispersion is used to characterize the backmixing and other deviations from plug flow. Due to unequal distribution of the fluid, the velocity of the fluid varies from channel to channel and hence the heat transfer coefficient variations are also taken into consideration. The computed outlet fluid temperatures are compared with experimental outlet temperatures, and the values of dispersive Peclet numbers are estimated. The results indicate that in order to get parameters independent of the number of plate used in single-blow experiment, it is essential to isolate flow maldistribution from backmixing. This paper has brought out a practical way in which this isolation can be done in the process of data reduction through suitable computational model.     

An experimental study of thermal performance of shell-and-coil heat exchangers

In the present study an experimental investigation of the mixed convection heat transfer in a coil-in-shell heat exchanger is reported for various Reynolds and Rayleigh numbers, various tube-to-coil diameter ratios and dimensionless coil pitch. The purpose of this article is to assess the influence of the tube diameter, coil pitch, shell-side and tube-side mass flow rate over the performance coefficient and modified effectiveness of vertical helical coiled tube heat exchangers. The calculations have been performed for the steady-state and the experiments were conducted for both laminar and turbulent flow inside coil. It was found that the mass flow rate of tube-side to shell-side ratio was effective on the axial temperature profiles of heat exchanger. The results also indicate that the ? − NTU relation of the mixed convection heat exchangers was the same as that of a pure counter-flow heat exchanger.     

Computer modeling and parametric study of a double effect generation absorption refrigeration cycle

This paper presents as assessment based on steady-state thermodynamic analysis and computer modeling of a double effect generation absorption refrigeration cycle for solar air-conditioning. The system consists of a second effect generator between the generator and condenser of the single effect absorption cycle and two solution heat exchangers between the absorber and the two generators. A numerical computer modeling of a water LiBr system based on the solution of simultaneous heat, mass and material balance equations for various components of the system has been carried out. The influences of component temperatures and heat exchanger effectiveness on the cooling coefficients of performance and component heat transfer rates have been investigated to obtain optimum operating conditions for the proposed air-conditioning system. Further, the single and double effect absorption cycles are compared with each other as well as with an ideal absorption cycle operating over the same range of temperatures.     

Analysis of coiled-tube heat exchangers to improve heat transfer rate with spirally corrugated wall

Steady heat transfer enhancement has been studied in helically coiled-tube heat exchangers. The outer side of the wall of the heat exchanger contains a helical corrugation which makes a helical rib on the inner side of the tube wall to induce additional swirling motion of fluid particles. Numerical calculations have been carried out to examine different geometrical parameters and the impact of flow and thermal boundary conditions for the heat transfer rate in laminar and transitional flow regimes. Calculated results have been compared to existing empirical formulas and experimental tests to investigate the validity of the numerical results in case of common helical tube heat exchanger and additionally results of the numerical computation of corrugated straight tubes for laminar and transition flow have been validated with experimental tests available in the literature. Comparison of the flow and temperature fields in case of common helical tube and the coil with spirally corrugated wall configuration are discussed. Heat exchanger coils with helically corrugated wall configuration show 80–100% increase for the inner side heat transfer rate due to the additionally developed swirling motion while the relative pressure drop is 10–600% larger compared to the common helically coiled heat exchangers. New empirical correlation has been proposed for the fully developed inner side heat transfer prediction in case of helically corrugated wall configuration.     

Experimental Performance of R-134a-Filled and Water-Filled Loop Heat Pipe Heat Exchangers

Experimental investigations were conducted to determine the thermal performances of an R-134a-filled thermosyphon heat pipe heat exchanger (THPHE) and a water-filled loop heat pipe heat exchanger (LHPHE) for hot and cold energy recovery for air conditioning purposes. For such applications, the heat pipe heat exchangers are operated at low temperatures. Both exchangers were operated in the countercurrent flow mode. This article presents the experimental results obtained. The results showed that heat transfer rate increased as evaporator inlet temperature increased and as both evaporator and condenser velocities increased. The overall effectiveness for the THPHE ranged from 0.8 to a minimum of about 0.5, while for the LHPHE it ranged from 0.9 to 0.3. Overall effectiveness was found to approach a minimum when both air streams have equal velocities.     

Numerical model and effectiveness correlations for a run-around heat recovery system with combined counter and cross flow exchangers

A two-dimensional steady-state numerical model is developed to study the heat transfer in a run-around heat recovery system with two exchangers each with a combination of counter and cross (counter/cross) flow between parallel plates or membranes. A finite difference method is used to solve the steady-state equations of continuity, momentum and heat transfer. The simulated values for the effectiveness of each counter/cross flow heat exchanger and the overall run-around system are used to develop effectiveness correlations which agree within ±2% of the simulated effectiveness of individual heat exchangers and overall system. It is shown that the effectiveness of this new run-around heat exchanger (RAHE) falls between the effectiveness of similar run-around systems with either two cross-flow exchangers or two counter-flow exchangers. For a given total surface area of the exchangers, the highest overall sensible effectiveness is achieved with exchangers which have a small exchanger aspect ratio and relatively small solution flow inlet and outlet lengths.     

Experimental study of heat transfer of buried finned pipe for ground source heat pump applications

Ground heat exchangers have vital importance for ground source heat pump applications. Various configurations tried to improve heat transfer in the soil. A new kind of aluminium finned pipe buried in the soil for this aim. In order to compare effectiveness of the Al finned pipe over the traditional PPRC pipe an experimental study carried out. The experimental GSHP system was installed at Y?ld?z Technical University Davupasa Campus on 800 m² surface area with no special surface cover. Temperature data were collected using thermocouples buried in soil horizontally and vertically at various distances from the pipe center and at the inlet and the outlet of the ground heat exchanger. Experimental results were compared with results from analytical study. To compare effectiveness of the Al finned pipe and PPRC pipe a new parameter defined as transferred amount of heat per unit mass of working fluid per unit time for this aim. It is found that Al finned pipe has higher heat transfer values than the traditional PPRC pipe.     

Second Law Efficiency Analysis of Heat Exchangers

Analytical analysis of unbalanced heat exchangers is carried out to study the second law thermodynamic performance parameter through second law efficiency by varying length‐to‐diameter ratio for counter flow and parallel flow configurations. In a single closed form expression, three important irreversibilities occurring in the heat exchangers—namely, due to heat transfer, pressure drop, and imbalance between the mass flow streams—are considered, which is not possible in first law thermodynamic analysis. The study is carried out by giving special influence to geometric characteristics like tube length‐to‐diameter dimensions; working conditions like changing heat capacity ratio, changing the value of maximum heat capacity rate on the hot stream and cold stream separately and fluid flow type, i.e., laminar and turbulent flows for a fully developed condition. Further, second law efficiency analysis is carried out for condenser and evaporator heat exchangers by varying the effectiveness and number of heat transfer units for different values of inlet temperature to reference the temperature ratio by considering heat transfer irreversibility. Optimum heat exchanger geometrical dimensions, namely length‐to‐diameter ratio can be obtained from the second law analysis corresponding to lower total entropy generation and higher second law efficiency. Second law analysis incorporates all the heat exchanger irreversibilities. © 2013 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley Online Library ( wileyonlinelibrary.com/journal/htj ). DOI 10.1002/htj.21109     

Heat pipe heat exchanger for heat recovery in air conditioning

The heat pipe heat exchangers are used in heat recovery applications to cool the incoming fresh air in air conditioning applications. Two streams of fresh and return air have been connected with heat pipe heat exchanger to investigate the thermal performance and effectiveness of heat recovery system. Ratios of mass flow rate between return and fresh air of 1, 1.5 and 2.3 have been adapted to validate the heat transfer and the temperature change of fresh air. Fresh air inlet temperature of 32–40 °C has been controlled, while the inlet return air temperature is kept constant at about 26 °C. The results showed that the temperature changes of fresh and return air are increased with the increase of inlet temperature of fresh air. The effectiveness and heat transfer for both evaporator and condenser sections are also increased to about 48%, when the inlet fresh air temperature is increased to 40 °C. The effect of mass flow rate ratio on effectiveness is positive for evaporator side and negative for condenser side. The enthalpy ratio between the heat recovery and conventional air mixing is increased to about 85% with increasing fresh air inlet temperature. The optimum effectiveness of heat pipe heat exchanger is estimated and compared with the present experimental data. The results showed that the effectiveness is close to the optimum effectiveness at fresh air inlet temperature near the fluid operating temperature of heat pipes.     

Experimental Investigation on Flow Boiling Heat Transfer of CO2 at Low Temperatures

There is a growing use of CO₂ refrigeration to achieve low temperatures, particularly in the food industry; however, very limited information is available in the open literature on its boiling heat transfer characteristics below –30°C. This paper investigates experimentally the flow boiling heat transfer of CO₂ at low temperatures down to –40°C. The experimental data were collected from a novel experimental rig, specifically designed to achieve low temperatures, using a 4.5 m long horizontal stainless steel tube of 4.57 mm inner diameter. The effects of heat and mass fluxes and saturation temperature on the flow boiling heat transfer coefficient are also analyzed. Furthermore, this paper highlights the limitations of existing empirical correlations by comparing their predictions with the experimental boiling heat transfer coefficients. It is expected that the data presented in this study would be beneficial to industry and designers of compact heat exchangers for CO₂ at low temperatures.     

Steady-State and Transient Behavior of Two Heat Exchangers Coupled by a Circulating Flowstream

Systems consisting of two heat exchangers coupled by a circulating flowstream are studied. The systems differ in the flow configurations of the single heat exchangers. For steady-state operation, there exists a heat capacity rate of the circulating flowstream that maximizes the temperature changes of the external flowstreams. Until now, this optimum has been calculated assuming that the overall heat transfer coefficients of the heat exchangers do not depend on the mass flow rate of the circulating flowstream. In this paper, the dependence of the overall heat transfer coefficient on the mass flow rate of the circulating flowstream is taken into account. For transient operating conditions, the system response to perturbations of inlet temperatures and mass flow rates is calculated by the method of Laplace Transforms and an explicit finite difference method. The most significant features of the coupled system become apparent by considering outlet temperature transients induced by perturbations of the mass flow rate of the circulating flowstream.     

Experimental investigation of single phase convective heat transfer coefficient in a corrugated plate heat exchanger for multiple plate configurations

Corrugated plate heat exchangers have larger heat transfer surface area and increased turbulence level due to the corrugations. In this study, experimental heat transfer data are obtained for single phase flow (water-to-water) configurations in a commercial plate heat exchanger for symmetric 30°/30°, 60°/60°, and mixed 30°/60° chevron angle plates. Experiments were carried out for Reynolds number ranging from 500 to 2500 and Prandtl number from 3.5 to 6.5. Experimental results show significant effect of chevron angle and Reynolds number on the heat transfer coefficient. Based on the experimental data, a correlation to estimate Nusselt number as a function of Reynolds number, Prandtl number and chevron angle has been proposed.     

Algebraic solution of capillary tube flows. Part II: Capillary tube suction line heat exchangers

Capillary tube suction line heat exchangers have been modeled using both numerical and analytical approaches. The former requires a reasonable understanding of the governing heat and fluid flow equations, thermodynamic relations, numerical methods, and computer programming, and therefore are not suitable for most refrigeration and air-conditioning practitioners. Alternatively, empirical algebraic formulations for diabatic capillary tube flows have been proposed in the literature, in spite of their lack of generality and accuracy. This paper introduces a physically consistent, unconditionally convergent, easy-to-implement semi-empirical algebraic model for capillary tube suction line heat exchangers, with the same level of accuracy as found with more sophisticated first-principles models. The methodology treats the refrigerant flow and the heat transfer as independent phenomena, thus allowing the derivation of explicit algebraic expressions for the refrigerant mass flow rate and the heat exchanger effectiveness. The thermal and hydraulic models are then conflated through the so-called Buckingham-π theorem using in-house experimental data collected for diabatic capillary tube flows of refrigerants HFC-134a and HC-600a. Comparisons between the model predictions and the experimental data revealed that more than 90% and nearly 100% of all data can be predicted within ±10% and ±15% error bands, respectively.     

Performance Deteriorations from Flow Maldistribution in Air-to-Air Heat Exchangers: A Parallel-Plates Membrane Core Case

Parallel-plates membrane cores have been widely used in air-to-air heat exchangers for fresh air heat and moisture recovery, which are also called total heat exchangers. Flow maldistribution and the consequent performance deteriorations are of great interest. The flow maldistribution is predicted with a CFD code, by treating the parallel-plates core as a two-dimensional porous media. Then, a coupled heat and moisture transfer model between the two air flows in the parallel-plates channels is set up. Using the CFD predicted flow distribution data on core face, the sensible heat and moisture exchange effectiveness and the performance deterioration factors are calculated with finite-difference scheme. Experiments are performed to validate the heat mass transfer model. The results indicate that for the current structure, when the channel pitch is below 2.0 mm, the flow distribution is quite homogeneous and the sensible and latent performance deteriorations due to flow maldistribution are below 9% and can be neglected. However, when the channel pitch is larger than 2 mm, the maldistribution is quite large and the consequent thermal and latent performance can be deteriorated by 28%. The flow maldistribution the consequent thermal and latent effectiveness deteriorations for parallel-plates cores are more serious than those for plate-fin cores previously reported.