共查询到20条相似文献,搜索用时 78 毫秒
1.
2.
3.
目前我国对于全身振动卫生标准乃参照ISO2631执行,而常用的测振仪器一般能测量计权振动级,对此如何参照?本文探讨了其对应关系,得到8小时振动暴露的疲劳—工效降低限相当于Z振级110dB,X、Y振级107dB。不同暴露时间不适用时间减半提高3dB的原则,本文得出了各暴露时间下每种界限对应的振动级。 相似文献
4.
5.
6.
7.
8.
本文介绍了一种新近研究开发的低频振动信号数据处理系统,它具有精度高,实时测量、分析、取得结果、不需后期处理,且采用了数理统计原理,使测量和分析更贴近实际状态。系统中的放大器部分,由于采用单片机控制,一改传统放大器模式,解决了自动调零、自动增益调整、自动放大倍数定标等一系列问题,从而为真正的多点测量创造了条件。系统的十六通道数为一个测点三个方向提供了同时可测量的五个测点和一个备用通道。十五路信息同时 相似文献
9.
在机械加工中产生的振动大都属于受迫振动或自激振动,与工艺系统的动态特性有关。本文详细分析了车削振动的主要类型及产生的原因、及其危害,并从刀具、夹具、切削工艺几方面提出了消除振动的建议及措施。 相似文献
10.
11.
The results of an investigation of different types of tungsten lamps in order to estimate the components of the error budget of spectrum-pyrometer apparatus are presented. Quantitative relations are considered and the results of experimental research, which enable systematic methods to be developed for eliminating the influence of polarization of the radiation of the lamps in standard radiation thermometry, are analyzed.Translated from Izmeritelnaya Tekhnika, No. 9, pp. 42–45, September, 2004. 相似文献
12.
本文研究用8098单片机对密闭大贮槽的贮液容量进行自动检测的应用系统,解决了把贮槽液位测量传感器输出的电流信号直接转换成贮液重量进行显示,从而使显示直观、清晰. 相似文献
13.
14.
15.
16.
17.
新的检定规程对检定条件、检定项目、检定方法、数据处理、检定结果处理和检定周期都进行了部分修改,本文从规程执行方面对自锁功能检查、加油机的最大允许误差及重复性的计算方法、加油机的付费金额误差的检定、掌握标准金属量器的滴定时间、首次检定时应注意的问题、数据处理时应注意的问题、加油机检定周期的合理调整、使用自动检定装置应注意的事项进行了总结。 相似文献
18.
19.
Based on the method of successive substitutions, an integral equation is derived in which multiple reflections are explicitly
identified. This equation is used provide simple methods of estimating the local effective radiation of two-dimensional and
three-dimensional systems of surfaces, with due regard for the anisotropy of their optical properties. A cylindrical cavity
confined by the surface of a right circular cylinder with a side pyrometric hole is treated as an example. The results obtained
by the suggested method are compared with the data of direct solution of an integral equation for the two-dimensional problem. 相似文献
20.
反渗透设备是水处理行业常用设备,广泛用于纯水、高纯水等的预处理.通过试验,找到两种降低反渗透设备出水电导率的方法:反渗透设备进水软化后加碱和反渗透设备进水酸化后脱气,这两种方法都有一定的应用范围,应根据工艺要求和运行费用选择使用. 相似文献