喷动床内气固二相流动行为的计算模拟

采用双流体模型结合颗粒动理学理论对喷动床内气固二相流体流动行为进行了计算模拟研究。模型中运用颗粒动理学理论描述颗粒相应力封闭流体控制方程,使用Gidaspow曳力模型描述气固相间作用。喷动床内颗粒在浓相区的体积分数很大,采用Schaeffer′s模型描述颗粒间的摩擦应力。模拟计算结果表明,喷动床内分喷射区、喷泉区、环隙区3个区域,在射流入口处形成一个瓶颈。模拟计算得到的颗粒速度和空隙度分布与实验数据进行比较,计算结果与实验结果吻合较好。     

摩擦-动力应力模型研究喷动床内气固两相流动过程

考虑颗粒滑动的半持续性接触应力和颗粒碰撞瞬时接触应力对颗粒相应力的贡献,建立了喷动床内气体颗粒两相流动计算模型。采用颗粒动理学和Johnson 等的摩擦应力模型,数值模拟喷动床颗粒流动过程,获得了喷动床喷射区、环隙区和喷泉区内颗粒流动特性。模拟计算与He等的实验结果进行了对比。同时分析了摩擦应力模型对颗粒相黏度变化的影响,表明中速颗粒流的颗粒相摩擦应力模型将直接影响喷动床气体颗粒两相流动的预测。     

喷动床内气固两相流动进口旋流效应数值模拟

为了研究喷嘴进口气体旋流效应对喷动床内气固两相流动特性的影响规律,采用数值模拟方法进行研究分析。通过欧拉-欧拉双流体模型和颗粒动力学理论对气固两相流动进行模型处理,分别对常规喷动床及带旋流器喷嘴喷动床进行模拟分析与对比。研究表明:喷嘴进口气体旋流效应显著地强化了喷动床内颗粒的径向运动,能有效消除柱锥区的颗粒堆积现象,扩大了低床层区气体喷射区的影响范围,增加了喷动床内气体的湍动能值,从而提高喷动床内颗粒处理的整体效率。存在最佳η(旋流器内径与外径比值)值,即η为0.526时,旋流气体对喷动床环隙区内颗粒堆积的消除作用及气体湍动能值的提升最为显著,同时旋流器喷动床的总体压降达到了峰值。     

喷动床内气固两相流动纵向涡流效应数值模拟

为了深入了解纵向涡流对喷动床内气固两相流动特性的影响规律,采用计算流体力学方法对喷动床内气固两相流动的纵向涡流效应进行三维数值模拟。采用RUC曳力系数模型描述气、固相间作用力,通过欧拉-欧拉双流体模型和颗粒动力学理论对气固两相流动进行模型处理。分别对无扰流件、加入一对小球扰流件及加入一对纵向涡流发生器喷动床结构进行了模拟分析及对比。研究表明:加入球体扰流件及纵向涡流发生器之后,喷泉区的喷动高度明显下降,并在球形扰流件及纵向涡流发生器附近产生了二次漩涡。纵向涡流的存在显著地增加了喷动床内环隙区颗粒相的径向速度,增加了喷射区及喷泉区内颗粒体积分数及其密集度,有效增强了喷动床内气体、颗粒沿径向与轴向的湍动能及拟温度值,进而强化了环隙区与喷射区内颗粒、流体两相的横向混合效果及颗粒间的动量交换过程。     

整体式多喷嘴喷动-流化床内气固两相流动规律数值模拟

采用双流体模型(TFM)对一种新型整体式多喷嘴喷动-流化床内气固两相流动进行了数值模拟,在喷动床锥体两侧开若干侧喷嘴形成辅助多喷嘴结构,使其在喷动床锥体处产生喷动-流化效果,从而对环隙区锥体边界处堆积颗粒层产生扰流作用。通过CFD数值模拟获得了喷动床内颗粒速度及浓度的分布情况,并与单喷嘴喷动床模拟结果进行对比。研究并优化分析了不同侧喷嘴数量以及侧喷嘴宽度等关键参数对喷动床气固两相流动的影响规律。研究表明,与常规喷动床相比,整体式多喷嘴喷动-流化床结构能有效增强喷动床内环隙区颗粒相运动,特别是强化了喷动床环隙区底部流动死区的颗粒运动,使得锥体边界层颗的粒体积分数显著下降,颗粒体积分数沿径向分布变得更为均匀,同时省略了旁路供气辅助设备。     

喷动床内气固两相流体动力行为的数值模拟

引　言喷动床被广泛应用于不同工业领域中 ,如石油裂解反应 -再生器、煤和农业废弃物气化和燃烧 ,喷动床还被应用于粮食和药品的干燥等[1] .因此 ,喷动床设计应满足不同应用的要求 .喷动床内气相反应物的反应时间和停留时间依赖于床体几何结构和运行参数 .尽管已有许多的实验对喷动床内气固两相流动进行了研究 ,得到了喷射区、环形区和喷泉区内的气固两相流动流体动力特性 ,然而由于喷动床内气固两相流动的复杂性 ,人们对床体几何结构和运行参数对喷动床动力学的影响至今并不清楚 .因此 ,床体几何结构和运行参数等对喷动床动力学的影响成为…     

三维整体式喷动-流化床结构优化与流动数值模拟

为了对环隙区内的颗粒堆积层产生局部流化作用,提出了一种在喷动床锥体处开一定数量侧喷嘴的整体式多喷嘴喷动-流化床结构,并采用双流体模型(TFM)对三维整体式多喷嘴喷动-流化床内的气固两相流动行为进行了数值模拟。通过计算流体力学(CFD)模拟获得了喷动床内颗粒体积分数、颗粒速度及流场均匀度分布情况,并将模拟结果与传统喷动床进行了对比,同时对锥体处开孔直径等关键参数进行了优化分析。结果表明:与常规喷动床相比,三维整体式多喷嘴喷动-流化床结构能有效增强喷动床环隙区与喷射区颗粒的径向混合,特别是流化了喷动床环隙区底部颗粒的流动死区。颗粒流场均匀度(CV)值随着床层高度的增加而上升,表明多喷嘴对颗粒流场的均匀化效应主要体现在喷动床柱锥区,当A_i/A_z=0.67时,侧喷嘴对喷动-流化床内整体的颗粒流化作用达到最佳。     

喷动床反应器气固流动模型的研究进展

首先对喷动床流动特征参数关联式进行了扼要介绍,继而着重总结了近年来喷动床内气固流动模型(喷射区气固稀相流模式、环隙区气体渗流模式以及固体颗粒流模式)、以及喷动床放大规律等基础理论研究的进展。最后,提出了未来喷动床流动模型工作的突破点和相应思路。     

喷动流化床流动特性数值模拟

为了捕捉喷动流化床中微观层次上的颗粒运动信息,建立了基于CFD的二维非稳态喷动流化床欧拉-欧拉两相流模型。分析了不同流化气速对喷动流化床气固流动特性的影响,即不同工况下的炉内压力降、颗粒浓度、床内空隙率分布、气体速度分布和固体颗粒速度分布。数值模拟研究结果表明:随流化气速的增大,压降和炉内平均空隙率逐渐增大,密相床层高度逐渐增加,沿着轴向方向的气体流量增大,喷动气的射流深度逐渐增加,同时射流半径也逐渐增加。     

《化工学报》2004年第55卷第2期目次

热力学　应用平均球近似理论计算锂盐有机溶液电导率传递现象　筛孔障碍物对半球气云爆燃压力增长机制影响的实验研究　气波管内波系影响因素的实验研究与数值模拟　水平气液混输管道清管操作试验与数值模拟技术　平行流分隔板管壳式换热器壳侧流场与传热性能　啮合同向三螺杆挤出机中三维等温流动的数值模拟　高压下Mellapak 35 0Y型波纹规整填料性能多相流　快速流化床提升管中气固流动行为的非线性分析　翼型组合桨持气特性的实验研究及数据关联方法　喷动床环隙区内颗粒流的数学模型和仿真　喷动床内气固两相流体动力行为的数值模拟催…     

CFD modeling of the gas-particle flow behavior in spouted beds

Gas-particle flow behavior in a cylindrical spouted bed and a three dimensional spout-fluid bed of spherical particles was simulated using the Eulerian-Eulerian two-fluid modeling approach, incorporating a kinetic-frictional constitutive model for dense assemblies of the particulate solid. The interaction between gas and particles was modeled using the Gidaspow drag model and the predicted hydrodynamic characteristics are compared with published experimental data. The overall flow patterns within the cylindrical spouted bed were predicted well by the model, i.e. a stable spout region, a fountain region and an annular downcomer region were correctly predicted by the model. The flow instabilities which develop in the spout-fluid bed are along with discussion of the mechanisms leading to instabilities. Bubble formation and motion of the bubbles inside the spout-fluid bed are also described. Such predictions can provide important information on the flow field within the spouted beds for process design and scale-up.     

基于动态双重网格下喷动床滞止区流动特性CFD-DEM数值模拟

基于Fortran语言自行开发了基于动态双重网格方法下的喷动床内气固两相流动的CFD-DEM方法,同时开展了喷动床内径向混合实验与模拟研究,又结合单网格方法对喷动床内0~2.0 s内的滞止区特性进行对比分析,验证了动态双网格方法计算结果的准确性。然后利用动态双网格方法对不同进口气速下和不同初始堆积高度下的喷动床进行数值模拟研究,对滞止区颗粒流动过程进行追踪,结果表明：径向混合实验结果与数值模拟结果有很好一致性;在喷动床内存在一定的滞止区,滞止区内的颗粒流动性较差;初始堆积高度不变,随着进口速度的增加,滞止区高度下降速率和向喷口延伸速度无明显变化;进口速度不变,随着初始堆积高度的增加,滞止区颗粒下降速度随之增加,但其向喷口延伸速度逐渐变慢。     

带纵向涡发生器喷动床内颗粒流动特性PIV实验

针对喷动床内环隙区颗粒缺少横/径向运动的特点,通过实验将纵向涡流发生器及纵向涡流效应引入喷动床。采用粒子图像测速技术研究了在内径为152 mm的喷动床内纵向涡流及颗粒设计参数对喷动床内喷射区及环隙区颗粒相径向速度的影响,研究结果表明,纵向涡发生器在扰流元件上方横截面内颗粒相运动出现大量二次涡流,相比较于无纵向涡流扰流件情况,喷动床内的颗粒径向速度得到了显著增加,表明纵向涡发生器能够增强颗粒相在喷射区及环隙区的径向运动能力。在喷动床稳定喷动范围内,颗粒直径及颗粒密度越小,纵向涡流对颗粒相径向运动的强化效果越佳。     

CFD simulation of gas–solid flow in a spouted bed with a non-porous draft tube

A multi-fluid Eulerian–Eulerian approach incorporating the kinetic theory of granular flow was used to simulate a spouted bed containing non-porous draft tube. Drag function and coefficient of restitution were investigated. Solid and gas velocity vector, gas flow rate in annulus and spout regions and longitudinal pressure distribution were evaluated. In addition, the effects of the entrainment height and the draft tube diameter were studied. Simulation indicates the formation of three regions namely, annulus, spout and fountain; similar to a conventional spouted bed. Current model predicts acceptable results in both spout and annulus regions. Simulation results indicate that the model can be employed for both mono-size and multi-size particles reasonably. This paper provides useful basis for further works on understanding gas–solid flow mechanism in spouted beds containing a non-porous draft tube.     

Effect of a Draft Tube on the Fluid Dynamics of a Spouted Bed: Experimental and CFD Studies

Knowledge about the gas and particle dynamics in spouted beds is important in the evaluation of particle circulation rates and the efficiency of gas-solid contacts. In this work, the mechanism of transition from a static bed to a spouted bed was numerically simulated using a Eulerian multiphase model. This model was applied to two distinct spouted bed geometries: a conventional device and a spouted bed with draft tube. The radial voidage and particle velocity profiles along the longitudinal position in the annular and spout regions were simulated for the geometries under study. The characteristic simulated curves were congruous with the experimental data.     

Effect of a Draft Tube on the Fluid Dynamics of a Spouted Bed: Experimental and CFD Studies

Knowledge about the gas and particle dynamics in spouted beds is important in the evaluation of particle circulation rates and the efficiency of gas-solid contacts. In this work, the mechanism of transition from a static bed to a spouted bed was numerically simulated using a Eulerian multiphase model. This model was applied to two distinct spouted bed geometries: a conventional device and a spouted bed with draft tube. The radial voidage and particle velocity profiles along the longitudinal position in the annular and spout regions were simulated for the geometries under study. The characteristic simulated curves were congruous with the experimental data.     

导向管直径对喷动床流动特性影响的计算颗粒流体力学数值模拟

导向管喷动床是较为常见的一种喷动床改进床型,通过阻断喷动区与环隙区气固接触来提高颗粒循环的规律性与稳定性。本文采用计算颗粒流体力学（CPFD）方法对于直径150mm的柱锥式导向管喷动床进行了数值模拟研究,考察了导向管直径对于喷动床内颗粒流动特性的影响,从环隙区死区分布、颗粒速度分布、固体循环量等方面分析了具有不同直径导向管喷动床的运行状态。结果表明,加入导向管在减少床内死区的同时也降低了运行时的固体循环量,对于本次采用的喷动床结构尺寸与运行参数,只有在导向管直径为40～60mm时才能保证床内具有良好喷动状态,综合考虑各因素,选用直径50～55mm的导向管最为合适。对于具有类似结构与运行条件的柱锥喷动床,导向管直径可考虑选为无导向管运行时喷动区直径的1.2～1.375倍。     

Simulations of flow behavior of gas and particles in spouted bed with a porous draft tube

Flow behaviors of particles in a two-dimensional spouted bed with a porous draft plates are studied using a fluid dynamic computation with kinetic-frictional stresses models. Gas flow through the porous draft tube is simulated by Brinkman-Darcy-Forchheimer formulation. The distributions of concentration and velocities of particles are predicted. Simulated results predict the solid circulation rate and gas flux rate measured in the spouted bed with a porous draft tube (Ishikura et al., 2003). The solid circulation rate in the spouted bed with a porous draft tube is larger than that with a non-porous draft tube. The predicted bed pressure drop with the porous draft tube is high in comparison to the spouted bed with non-porous draft tube. The effect of the porosity of the porous draft tube on distributions of gas flux rate through the annulus and solid circulation rate are discussed.