Crystal structure of Kuzel's salt 3CaO·Al2O3·1/2CaSO4·1/2CaCl2·11H2O determined by synchrotron powder diffraction

The crystal structure of Kuzel's salt has been successfully determined by synchrotron powder diffraction. It crystallizes in the rhombohedral R3? symmetry with a = 5.7508 (2) Å, c = 50.418 (3) Å, V = 1444.04 (11) ų. Joint Rietveld refinement was realized using three X-ray powder patterns recorded with a unique wavelength and three different sample-to-detector distances. Kuzel's salt is the chloro-sulfoaluminate AFm phase and belongs to the layered double hydroxide (LDH) large family. Its structure is composed of positively charged main layer [Ca₂Al(OH)₆]⁺ and negatively charged interlayer [Cl_0.50·(SO₄)_0.25·2.5H₂O]⁻. Chloride and sulfate anions are ordered into two independent crystallographic sites and fill successive interlayer leading to the formation of a second-stage compound. The two kinds of interlayer have the compositions [Cl·2H₂O]⁻ and [(SO₄)_0.5·3H₂O]⁻. The crystal structure explains why chloride and sulfate anions are not substituted and why the formation of extended solid solution in the chloro-sulfate AFm system does not occur.     

Electropolishing of NiTi shape memory alloys in methanolic H2SO4

The electropolishing of NiTi shape memory alloys was surveyed electrochemically. Anodic polarization of NiTi up to 8 V was performed in various aqueous and methanolic H₂SO₄ solutions. The passivity could be overcome in methanolic solutions with 0.1 mol dm−3≤CH₂SO₄≤7 mol dm−3. The dissolution kinetics was studied in dependence of the polarization potential, the H₂SO₄-concentration, the water concentration and the temperature. For lower concentrations of sulfuric acids (CH₂SO₄≤0.3 mol dm−3) electropolishing conditions were not observed for potentials up to 8 V. The dissolution remained under Ohmic control. In the concentration range from 1 to 7 mol dm⁻³ a potential independent limiting current was registered depending linearly on the logarithm of concentration. The best results were obtained with a 3 mol dm⁻³ methanolic sulfuric acid at 263 K which yielded an electropolishing current of 500 A m⁻² at a potential of 8 V. Surface roughness as well as current efficiency showed an optimum under these conditions.     

The distribution of antimony in the oxide layer formed by potentiostatic oxidation of Pb-Sb alloy

The distribution of antimony within the oxide films on Pb-Sb alloy prepared by potentiostatic oxidation in H₂SO₄ solutions was examined by SIMS. The study of oxide films prepared by applying different potentials for three hours showed that two types of film were obtained depending on whether the potential was more negative or more positive than 1·5 V. Antimony profiles were obtained for films at several stages in the initial growth. It was found that antimony was retained in the oxide film at 1·5 V during both nucleation and two- or three-dimensional growth of PbO₂ and at 1·6 V during the lateral overlaps of three-dimensional centres of PbO₂. Relationships between the antimony distribution profiles and the oxide film growth are discussed.     

Anion water in gypsum (CaSO4·2H2O) and hemihydrate (CaSO4·1/2H2O)

The bonding nature of water in gypsum, CaSO₄·2H₂O, and hemihydrate, CaSO₄·1/2H₂O, was suggested by characteristic absorption bands of water and sulphate ions. The infrared spectral data indicate the presence of anion water in gypsum and hemihydrate through hydrogen bonding. Negative shifting of bending vibration of SO₄ ion and lowering and broadening of the O-H stretching vibration at around 3600 cm⁻¹ indicate the presence of both anion water and hydrogen bonding in gypsum and hemihydrate     

One step solid state synthesis of FeF3·0.33H2O/C nano-composite as cathode material for lithium-ion batteries

Nanometer-sized FeF₃·0.33H₂O/acetylene black composite has been synthesized by one step chemico-mechanical ball-milling process using Fe (NO₃)₃?9H₂O and NH₄F as precursors and investigated as cathode materials for secondary lithium batteries. The obtained FeF₃·0.33H₂O/C composite was described in terms of structure, morphology, and electro-chemical performance. The composite exhibited a noticeable capacity of 233.9 mAh g⁻¹ at a current density of 20 mA g⁻¹ within potential range 1.8–4.5 V and good rate capability. These results showed that FeF₃·0.33H₂O/C nano-composite prepared from an easily scalable chemico-mechanical ball-milling process was of great industrial interest.     

Electrochemical capacitance of nanoporous hydrous RuO2 templated by anionic surfactant

The nanoporous RuO₂·3.38H₂O was synthesized with a surfactant template using sodium dodecyl sulfate. The surface area of the material amounted to 220 m² g⁻¹ while the maximum specific capacitance obtained was 870 Fg⁻¹ at a scan rate of 10 mV s⁻¹. The specific capacitance of nanoporous RuO₂·3.38H₂O electrode exhibits enhancement, compared with other porous RuO₂ materials synthesized by different methods. The nanoporous RuO₂·3.38H₂O is a very promising material for high performance capacitance.     

A low-potential, H2O2-assisted electrodeposition of cobalt oxide/hydroxide nanostructures onto vertically-aligned multi-walled carbon nanotube arrays for glucose sensing

A novel nanocomposite was synthesized using a cathodic, low-potential, electrochemical reduction of H₂O₂ to homogeneously deposit cobalt oxide/hydroxide (denoted as CoOx·nH₂O) nanostructures onto vertically well-aligned multi-walled carbon nanotube arrays (MWCNTs), while the MWCNTs were prepared by catalytic chemical vapor deposition (CVD) on a tantalum (Ta) substrate. The CoOx·nH₂O–MWCNTs nanocomposite exhibits much higher electrocatalytic activity towards glucose (Glc) after modification with CoOx·nH₂O than before. This non-enzymatic Glc sensor has a high sensitivity (162.8 μA mM⁻¹ cm⁻²), fast response time (<4 s) and low detection limit (2.0 μM at signal/noise ratio = 3), and a linear dynamic range up to 4.5 mM. The sensor output is stable over 30 days and unaffected by common interferents that co-exist with Glc in analytical samples; it is also resistant to chloride poisoning. These features make the CoOx·nH₂O–MWCNTs nanocomposite a promising electrode material for non-enzymatic Glc sensing in routine analysis.     

Electrochemical behavior of LiCoO2 in a saturated aqueous Li2SO4 solution

The electrochemical behavior of a commercial LiCoO₂ with spherical shape in a saturated Li₂SO₄ aqueous solution was investigated with cyclic voltammetry and electrochemical impedance spectroscopy. Three redox couples at E_SCE = 0.87/0.71, 0.95/0.90 and 1.06/1.01 V corresponding to those found at ELi/Li⁺=4.08/3.83, 4.13/4.03 and 4.21/4.14 V in organic electrolyte solutions were observed. The diffusion coefficient of lithium ions is 1.649 × 10⁻¹⁰ cm² s⁻¹, close to the value in organic electrolyte solutions. The results indicate that the intercalation and deintercalation behavior of lithium ions in the Li₂SO₄ solution is similar to that in the organic electrolyte solutions. However, due to the higher ionic conductivity of the aqueous solution, current response and reversibility of redox behavior in the aqueous solution are better than in the organic electrolyte solutions, suggesting that the aqueous solution is favorable for high rate capability. The charge transfer resistance, the exchange current and the capacitance of the double layer vary with the charge voltage during the deintercalation process. At the peak of the oxidation (0.87 V), the charge transfer resistance is the lowest. These fundamental results provide a good base for exploring new safe power sources for large scale energy storage.     

The solubility of selenate-AFt (3CaO·Al2O3·3CaSeO4·37.5H2O) and selenate-AFm (3CaO·Al2O3·CaSeO4·xH2O)

The Se(VI)-analogues of ettringite and monosulfate, selenate-AFt (3CaO·Al₂O₃·3CaSeO₄·37.5H₂O), and selenate-AFm (3CaO·Al₂O₃·CaSeO₄·xH₂O) were synthesised and characterised by bulk chemical analysis and X-ray diffraction. Their solubility products were determined from a series of batch and resuspension experiments conducted at 25 °C. For selenate-AFt suspensions, the pH varied between 11.37 and 11.61, and a solubility product, log K_so=61.29±0.60 (I=0 M), was determined for the reaction 3CaO·Al₂O₃·3CaSeO₄·37.5H₂O+12 H⁺⇔6Ca²⁺+2Al³⁺+3SeO₄²⁻+43.5H₂O. Selenate-AFm synthesis resulted in the uptake of Na, which was leached during equilibration and resuspension. For the pH range of 11.75 to 11.90, a solubility product, log K_so=73.40±0.22 (I=0 M), was determined for the reaction 3CaO·Al₂O₃·CaSeO₄·xH₂O+12 H⁺⇔4Ca²⁺+2Al³⁺+SeO₄²⁻+(x+6)H₂O. Thermodynamic modelling suggested that both selenate-AFt and selenate-AFm are stable in the cementitious matrix; and that in a cement limited in sulfate, selenate concentration may be limited by selenate-AFm to below the millimolar range above pH 12.     

Hydrothermal synthesis and electrochemical capacitance of RuO2·xH2O loaded on benzenesulfonic functionalized MWCNTs

Amorphous RuO₂·xH₂O was well coated on the benzenesulfonic functionalized multi-wall carbon nanotubes (f-MWCNTs) successfully via hydrothermal method. The decorated benzenesulfonic groups served as a bifunctional role both for solubilizing and dispersing MWCNTs into aqueous solution and for tethering Ru³⁺ precursor to facilitate the following uniform chemical deposition of RuO₂·xH₂O. The electrochemical performance of RuO₂/f-MWCNTs and utilization of RuO₂·xH₂O were evidenced by cyclic voltammetry and galvanostatic charge/discharge tests. The specific capacitance of 1143 Fg⁻¹ for RuO₂·xH₂O was obtained from RuO₂/f-MWCNTs with 32 wt.% RuO₂·xH₂O, which was much higher than that of just 798 Fg⁻¹ for the RuO₂/p-MWCNTs. Even though the RuO₂·xH₂O loading increases to 45 wt.%, the utilization of RuO₂·xH₂O still possesses as high as 844.4 Fg⁻¹, indicating a good energy capacity in the case of high loading.     

Electrochemical behaviour of titanium in H2SO4-MnSO4 electrolytes

The corrosion of titanium in H₂SO₄ electrolytes (0.001-1.0 M) at temperatures from ambient to 98 °C has been investigated using steady-state polarization measurements. Four distinct regions of behaviour were identified, namely active corrosion, the active-passive transition, passive region and the dielectric breakdown region. The active corrosion and active-passive transition were characterized by anodic peak current (i_m) and voltage (E_m), which in turn were found to vary with the experimental conditions, i.e., d(log?(im))/dpH=−0.8±0.1 and dE_m/dpH which was −71 mV at 98 °C, −58 mV at 80 °C and −28 mV at 60 °C. The activation energy for titanium corrosion, determined from temperature studies, was found to be 67.7 kJ mol⁻¹ in 0.1 M H₂SO₄ and 56.7 kJ mol⁻¹ in 1.0 M H₂SO₄. The dielectric breakdown voltage (E_d) of the passive TiO₂ film was found to vary depending on how much TiO₂ was present. The inclusion of Mn²⁺ into the H₂SO₄ electrolyte, as is done during the commercial electrodeposition of manganese dioxide, resulted in a decrease in titanium corrosion current, possibly due to Mn²⁺ adsorption limiting electrolyte access to the substrate.     

Synthesis and electrical properties of the (PVA)0.7(KI)0.3·xH2SO4 (0 ≤ x ≤ 5) polymer electrolytes and their performance in a primary Zn/MnO2 battery

Solid acid polymer electrolytes (SAPE) were synthesised using polyvinyl alcohol, potassium iodide and sulphuric acid in different molar ratios by solution cast technique. The temperature dependent nature of electrical conductivity and the impedance of the polymer electrolytes were determined along with the associated activation energy. The electrical conductivity at room temperature was found to be strongly depended on the amorphous nature of the polymers and H₂SO₄ concentration. The ac (100 Hz to 10 MHz) and dc conductivities of the polymer electrolytes with different H₂SO₄ concentrations were analyzed. A maximum dc conductivity of 1.05 × 10⁻³ S cm⁻¹ has been achieved at ambient temperature for electrolytes containing 5 M H₂SO₄. The frequency and temperature dependent dielectric and electrical modulus properties of the SAPE were studied. The charge transport in the present polymer electrolyte was obtained using Wagner's polarization technique, which demonstrated the charge transport to be mainly due to ions. Using these solid acid polymer electrolytes novel Zn/SAPE/MnO₂ solid state batteries were fabricated and their discharge capacity was calculated. An open circuit voltage of 1.758 V was obtained for 5 M H₂SO₄ based Zn/SAPE/MnO₂ battery.     

Large-scale synthesis of WO3 nanoplates by a microwave-hydrothermal method

Tungsten oxide (WO₃) nanoplates were synthesized by a 270 W microwave-hydrothermal reaction of Na₂WO₄·2H₂O and citric acid (C₆H₈O₇·H₂O) in deionized water. X-ray diffraction (XRD), scanning electron microscopy (SEM), high resolution transmission electron microscopy (HRTEM), and selected area electron diffraction (SAED) were used to reveal the synthesis of WO₃ complete rectangular nanoplates in the solution of 0.2 g citric acid for 180 min, with O-W-O FTIR stretching modes at 819 and 741 cm⁻¹, and two prominent O-W-O Raman stretching modes at 804 and 713 cm⁻¹. The 2.71 eV indirect energy gap, and 430-460 nm blue emission wavelength range of WO₃ complete rectangular nanoplates were determined using UV-visible and photoluminescence (PL) spectrometers. The formation mechanism was also proposed according to the experimental results.     

In situ scanning tunneling microscopy study of selective dissolution of Au3Cu and Cu3Au (0 0 1)

We present an electrochemical study of Au₃Cu (0 0 1) single crystal surfaces in 0.1 mol dm⁻³ H₂SO₄ and 0.1 mol dm⁻³ H₂SO₄ + 0.1 mmol dm⁻³ HCl, and of Cu₃Au (0 0 1) in 0.1 mol dm⁻³ H₂SO₄. The focus is on in situ scanning tunneling microscopy experiments. The changes of the surface morphology, which are time- and potential-dependent, have been observed, clearly resolving single atomic steps and mono-atomic islands and pits. Chloride additives enhance the surface diffusion and respective morphologies are observed earlier. All surfaces have shown considerable roughening already in the passive region far below the critical potential.     

Faradaic rectification studies of some reactions at the mercury/solution interface

The kinetic parameters of Hg₂²⁺, 1·0 M HClO₄/Hg and Fe(Ox)₃³⁻, Fe(Ox)₃⁴⁻, 0·5 M K₂ (Ox), 0·7 N H₂SO₄/Hg reactions have been obtained by faradaic rectification at radio frequencies. The value of I_a°, the exchange current density for discharge of 1·0 mM and 0·5 mM of mercurous ions on mercury in 1·0 M perchloric acid is 3·9 A/cm² and 1·1 A/cm² respectively. The rate constant k_a° for the reaction is of the order of 0·9 × 10⁻² cm/s at 35°C and the transfer coefficient is 0·56. The values of kinetic parameters obtained for the discharge of mercurous ions have been compared with data obtained by others using different methods. The value of α for Fe(Ox)₃³⁻/Fe(Ox)₂⁴⁻, 0·5 M K₂(Ox)/Hg reaction is 1·0.     

Effects of complex agents on the anodic deposition and electrochemical characteristics of cobalt oxides

The anodic deposition rate of cobalt oxide from CoCl₂·6H₂O is strongly affected by the type of complex agents (acetate ion (AcO⁻), citrate ion, EDTA) added into the deposition solutions. The oxidation potential of CoCl₂·6H₂O, examined by linear sweep voltammetry (LSV), is negatively shifted from ca. 1.1 V to about 0.8, 0.5, and 0.2 V by adding AcO⁻, citrate ion, and EDTA, respectively. The deposition rate of cobalt oxide is found to depend not only on the coordinating strength between Co and ligands but also on the conversion rate of the Co-L complexes (L: ligand) into the oxy-hydroxyl-Co species after electron transfer. The textural and electrochemical characteristics of resultant Co oxides, examined by X-ray photoelectron spectroscopic (XPS), scanning electron microscopic (SEM), open-circuit potential versus time, and cyclic voltammetric analyses, are also influenced by varying the complex agents. The deposition rate is the highest when the Co oxide is deposited from the precursor solution containing AcO⁻, which also exhibits the highest specific capacitance of ca. 230 F g⁻¹ among all Co oxide deposits (as the oxide loading ≥0.05 mg cm⁻²), demonstrating its most promising applicability in the electrochemical supercapacitors.     

A new rechargeable lithium-ion battery with a xLi2MnO3·(1 − x) LiMn0.4Ni0.4Co0.2O2 cathode and a hard carbon anode

We reported a new type of rechargeable lithium-ion battery consisting of a structurally integrated 0.4Li₂MnO₃·0.6LiMnNi_0.4Co_0.2O₂ cathode and a hard carbon anode. The drawback of the high irreversible capacity loss of both electrodes, occurring at the first charge/discharge process, can be counterbalanced each other. The battery shows good reversibility with a sloping voltage from 1.5 V to 4.5 V and delivers a capacity of 105 mA h g⁻¹ and a specific energy of 315 W h kg⁻¹ based on the total weight of the both active electrode materials.     

Synthesis of LiVOPO4 for cathode materials by coordination and microwave sintering

Lithium vanadyl phosphate (LiVOPO₄) sample, as one potential cathode materials, was synthesized via a route of coordination and microwave sintering. The precursors were prepared by coordination reactions among LiOH·H₂O, NH₄VO₃, NH₄H₂PO₄, C₆H₈O₇·H₂O and a small amount of water, and then they were sintered in a microwave furnace at 600 °C for 50 min. X-ray diffraction (XRD) results confirmed the formation of crystallized LiVOPO₄ with orthorhombic structures belonging to the space group of Pnma. Scanning electron microscopy (SEM) measurements indicated that the average particle size was less than 500 nm. After undergone an “activation” process, the sample exhibited a high discharge capacity for about 154 mA h g⁻¹ by the 22nd cycle at a current of 18.5 mA g⁻¹, which was very close to the theoretical values. Though the discharge capacity decreased obviously with the increased current, 110 as well as 80 mA h g⁻¹ can still be sustained within 40 cycles at 38 and 75 mA g⁻¹ respectively. This paper showed that submicron-sized LiVOPO₄ materials prepared through above way should be prospective for the application to 4 V system of lithium ion batteries.     

Electrodeposited PbO2 thin film as positive electrode in PbO2/AC hybrid capacitor

Lead dioxide (PbO₂) thin films were prepared on Ti/SnO₂ substrates by means of electrodeposition method. Galvanostatic technique was applied in PbO₂ film formation process, and the effect of deposition current on morphology and crystalline form of the PbO₂ thin films was studied by means of scanning electron microscopy (SEM) and X-ray diffraction (XRD). The energy storage capacity of the prepared PbO₂ electrode was investigated by means of cyclic voltammetry (CV) and charge/discharge cycles, and a rough surface structure PbO₂ film was selected as positive electrode in the construction of PbO₂/AC hybrid capacitor in a 1.28 g cm⁻³ H₂SO₄ solution. The electrochemical performance was determined by charge/discharge tests and electrochemical impedance spectroscopy (EIS). The results showed that the PbO₂/AC hybrid capacitor exhibited high capacitance, good cycling stability and long cycle life. In the voltage range of 1.8-0.8 V during discharge process, considering the weight of all components of the hybrid capacitor, including the two electrodes, current collectors, H₂SO₄ electrolyte and separator, the specific energy and power of the device were 11.7 Wh kg⁻¹ and 22 W kg⁻¹ at 0.75 mA cm⁻², and 7.8 Wh kg⁻¹ and 258 W kg⁻¹ at 10 mA cm⁻² discharge currents, respectively. The capacity retains 83% of its initial value after 3000 deep cycles at the 4 C rate of charge/discharge.     

Study of the kinetics and the influence of Biirr on formic acid oxidation at Pt2Ru3/C

Electrochemical oxidation of HCOOH in H₂SO₄ and HClO₄ solutions was examined on thin film Pt₂Ru₃/C electrode. XRD pattern revealed that Pt₂Ru₃ alloy consisted of the solid solution of Ru in Pt and the small amount of Ru or solid solution of Pt in Ru. According to STM images, Pt₂Ru₃ particles size was between 2 and 6 nm. It was established that electrochemical oxidation of HCOOH commenced at −0.1 V versus SCE at Pt sites in the catalyst. Kinetic parameters indicated that dehydrogenation path was predominant. Dehydration occurs in parallel, but without significant poisoning by CO_ad owing to oxidative removal by OH species on Ru atoms. The coverage of Pt₂Ru₃ surface by CO preadsorbed from the solution was found to be 24% lower when the surface was modified by irreversibly adsorbed Bi. Modification by Bi also shifted the onset potential for HCOOH oxidation for about 50 mV towards more negative values and consequently, increased the reaction rate for a factor of two. It was proposed that Ru acts through bifunctional mechanism, i.e. OH species adsorbed on Ru oxidizes CO_ad from Pt sites, while Bi hinders the adsorption of CO on Pt sites via electronic and/or ensemble effects.