Temperature‐Dependent Phase Transitions in the Lead‐Free Piezoceramics (1 – x – y)(Bi1/2Na1/2)TiO3–xBaTiO3–y(K0.5Na0.5)NbO3 Observed by in situ Transmission Electron Microscopy and Dielectric Measurements

Lead‐free piezoelectric (1 – x – y)(Bi_1/2Na_1/2)TiO₃–xBaTiO₃–y(K_0.5Na_0.5)NbO₃ (BNT–BT–KNN) ceramics were examined in situ under increasing temperature in the transmission electron microscope. Changing superstructure reflections indicate a transition from rhombohedral to tetragonal to cubic phase with broad coexistence regions. The additional evolution of the microstructure in combination with dielectric measurements leads to a model of two relaxor‐type phase evolutions with temperature.     

Composition‐ and Temperature‐Dependent Large Strain in (1−x)(0.8Bi0.5Na0.5TiO3–0.2Bi0.5K0.5TiO3)– xNaNbO3 Ceramics

Ternary solid solutions of (1 ? x)(0.8Bi_0.5Na_0.5TiO₃–0.2Bi_0.5K_0.5TiO₃)– xNaNbO₃ (BNKT–xNN) lead‐free piezoceramics were fabricated using a conventional solid‐state reaction method. Pure BNKT composition exhibited an electric‐field‐induced irreversible structural transition from pseudocubic to ferroelectric rhombohedral phase at room temperature. Accompanied with the ferroelectric‐to‐relaxor temperature T_F‐R shifted down below room temperature as the substitution of NN, a compositionally induced nonergodic‐to‐ergodic relaxor transition was presented, which featured the pinched‐shape polarization and sprout‐shape strain hysteresis loops. A strain value of ~0.445% (under a driving field of 55 kV/cm) with large normalized strain of ~810 pm/V was obtained for the composition of BNKT–0.04NN, and the large strain was attributed to the reversible electric‐field‐induced transition between ergodic relaxor and ferroelectric phase.     

Quenching-circumvented ergodicity in relaxor Na1/2Bi1/2TiO3-BaTiO3-K0.5Na0.5NbO3

Quenching alkaline bismuth titanates from sintering temperatures results in increased lattice distortion and consequently higher depolarization temperature. This work investigates the influence of quenching on the ergodicity of relaxor Na_1/2Bi_1/2TiO₃-BaTiO₃-K_0.5Na_0.5NbO₃. A distinct departure from ergodicity is evidenced from the increase in remanent polarization and the absence of frequency dispersion in the permittivity response of poled samples. Further, the samples exhibit enhanced negative strain upon application of electric field, indicating proclivity towards correlated polar nanoregions, corroborated by the enhanced tetragonal distortion. As a result, ergodic relaxor Na_1/2Bi_1/2TiO₃-6BaTiO₃-3K_0.5Na_0.5NbO₃ exhibits a depolarization temperature of 85°C with a 60% increase in remanent polarization and approximately a threefold increase in remanent strain upon quenching. Quenching-induced changes in the local environment of Na⁺ and Bi³⁺ cations hinder the development of ergodicity promoted by the A-site disorder. These results provide new insight into tailoring ergodicity of relaxor ferroelectrics.     

Electrical properties and temperature stability of SrTiO3-modified (Bi1/2Na1/2)TiO3-BaTiO3-(K1/2Na1/2)NbO3 piezoceramics

SrTiO₃-modified lead-free piezoelectric ceramics, (0.93-x)Bi_0.5Na_0.5TiO₃-xSrTiO₃-0.06BaTiO₃-0.01 K_0.5Na_0.5NbO₃ [(BNT-xST)-BT-KNN, x = 0-0.06], were prepared using a conventional solid-state reaction method. The XRD structure analysis and electric properties characteristics revealed the ST-induced phase transformation from the ferroelectric phase to the relaxor phase and their coexistence state. Benefiting from the ST-destructed ferroelectric long-range orders, the high normalized strain value of 600 pm/V was obtained in the (BNT-0.02ST)-BT-KNN ceramic at 5 kV/mm. The ST-generated relaxor phase was found to have a constructive effect on improving the temperature stability and restraining the hysteresis of the electric-field-induced strain. The normalized strain of (BNT-0.06ST)-BT-KNN ceramics could be kept at a high value ~337 pm/V at elevated temperature up to 120°C.     

Effect of Texture on Temperature‐Dependent Properties of K0.5Na0.5NbO3 Modified Bi1/2Na1/2TiO3–xBaTiO3

Textured (1?x?y)Bi_1/2Na_1/2TiO₃–xBaTiO₃–yK_0.5Na_0.5NbO₃ (BNT–100xBT–100yKNN) ceramics with a {001} pseudocubic (pc) orientation were fabricated by templated grain growth using Bi_1/2Na_1/2TiO₃ templates. Temperature‐dependent electromechanical results demonstrate that the strain response of templated BNT–xBT–yKNN ceramics is stable from room temperature (RT) to 125°C. The temperature‐dependent strain and polarization response are compared to randomly oriented ceramics, for BNT–100xBT–2KNN (0.05 ≤ x ≤ 0.07). Textured BNT–7BT–2KNN reached a maximum 0.47% strain response at 5 kV/mm, an almost 50% increase compared to randomly oriented BNT–7BT–2KNN. Over the temperature range RT–125°C, the strain response of templated BNT–6BT–2KNN degraded from 0.38% to 0.22% (?42.1%) compared to 0.37% to 0.18% (?51.4%) for randomly oriented ceramics. The temperature‐dependent strain response suggests that templated BNT–100xBT–100yKNN ceramics are well suited for elevated temperature applications.     

The Relationship Between Phase Structure and Electrical Properties in (1 − x)(Bi0.5Na0.5TiO3–Ba0.5K0.5TiO3–BaTiO3)‐ xK0.5Na0.5NbO3 Quaternary Lead‐Free Piezoelectric Ceramics

(1 ? x)(0.85Bi_0.5Na_0.5TiO₃–0.11Ba_0.5K_0.5TiO₃–0.04BaTiO₃)‐ xK_0.5Na_0.5NbO₃ lead‐free piezoelectric ceramics with x = 0.00, 0.02, 0.03, 0.04, 0.05, and 0.10 were prepared by a conventional solid state method. A coexistence of rhombohedral (R) and tetragonal (T) phases was found in the system, which tended to evolve into pseudocubic symmetry when x increases. The x = 0.04 sample exhibited improved electrical properties: the dielectric constant ε_r = 1900 with the low loss tangents 0.06, the S_max/E_max of ~400 and ~460 pm/V under unipolar and bipolar electric field, respectively. Meanwhile, piezoelectric constant d₃₃ still maintained ~160 pC/N. These could be owed to the formation of polar nanoregions for relaxor phase.     

Large Strain Response in 0.99(Bi0.5Na0.4K0.1)TiO3–0.01(KxNa1−x)NbO3 Lead‐Free Ceramics Induced by the Change of K/Na Ratio in (KxNa1−x)NbO3

Influence of K/Na ratio in (K_xNa_1?x)NbO₃ on the ferroelectric stability and consequent changes in the electrical properties of 0.99(Bi_0.5Na_0.4K_0.1)TiO₃–0.01(K_xNa_1?x)NbO₃ (BNKT–K_xNN) ceramics were investigated. Results showed that change of K/Na ratio in KNN induces a phase transition from ferroelectric to ergodic relaxor phase with a significant disruption of the long‐range ferroelectric order, and correspondingly adjusts the ferroelectric–relaxor transition point T_F?R to room temperature. Accordingly, giant strain of ~0.46% (corresponding to a large signal d₃₃* of ~575 pm/V) which is comparable to that of Pb‐based antiferroelectrics is obtained at a K/Na ratio of ~1, and the emergence of large strain response induced by the change of K/Na ratio of KNN can be well explained by the correlation between the position of ferroelectric–ergodic relaxor phase boundary in the BNKT–K_xNN system and the tolerance factor t of the end number (K_xNN). In situ high‐energy X‐ray scattering experiments with external field reveals that the large strain response in the studied system is likely related to the electric field‐induced distortion from the pseudocubic structure.     

High‐Temperature Multilayer Ceramic Capacitors Based on 100−x(94Bi1/2Na1/2TiO3–6BaTiO3)–xK0.5Na0.5NbO3

The potential high‐temperature dielectric materials 100?x(94Bi_1/2Na_1/2TiO₃–6BaTiO₃)–xK_0.5Na_0.5NbO₃ with x = 12, 18, and 24 were processed as bulk samples in order to examine the reduction of sintering temperature by means of CuO as sintering aid. Due to the successful reduction of sintering temperature, low cost Ag:Pd could be used as a co‐fired electrode material for multilayer ceramic capacitors (MLCCs). Fabrication of 8 μm thick, dense MLCCs with self‐contained, nonreactive electrodes is reported for a wide range of compositions of Bi_1/2Na_1/2TiO₃–BaTiO₃–K_0.5Na_0.5NbO₃. Among the manufactured MLCCs, those with compositions x = 24 showed the most promising dielectric properties for applications where high operating temperatures are needed. The temperature‐dependence of permittivity was quite low, revealing a change of less than ±10% compared to its 150°C‐value in the range of 40°C–225°C. For samples sintered at 1000°C, an RC constant of about 300 s was obtained at 150°C. Furthermore, these x = 24 MLCCs exhibited the finest microstructures among the compositions examined; making it a suitable candidate for further miniaturization of layer thickness as required for state‐of‐the art devices.     

Impedance Spectroscopy of (Bi1/2Na1/2)TiO3–BaTiO3 Ceramics Modified with (K0.5Na0.5)NbO3

The electrical and dielectric properties of (1 ? x)(0.94Bi_1/2Na_1/2TiO₃–0.06BaTiO₃)–x(K_0.5Na_0.5NbO₃) with x = 0, 0.03, 0.09, 0.18 have been investigated by impedance spectroscopy over a wide temperature range. The dc conductivity of the ceramics follows the Arrhenius law with an activation energy ranging from ~1.20 to 1.50 eV. Measurements under different atmospheres show the materials exhibit n‐type semiconducting behavior at elevated temperatures. The presence of a highly polarizable phase for all compositions is revealed by electric modulus (M″) spectra. The Burns temperature decreases with increasing KNN content. The change in temperature‐dependent permittivity with composition is explained by the difference in thermal evolution of polar nanoregions induced by the addition of KNN.     

Large strain response with low driving field in Bi1/2Na1/2TiO3–Bi1/2K1/2TiO3–Bi(Mg2/3Nb1/3)O3 ceramics

The (1?x)(0.8Bi_1/2Na_1/2TiO₃–0.2Bi_1/2K_1/2TiO₃)?xBiMg_2/3Nb_1/3O₃ (100xBMN) ternary solid solutions were designed and prepared using a conventional solid‐state reaction. Temperature and compositional dependent ferroelectric, piezoelectric, dielectric features, and structural evolution were systematically studied. At the critical composition of 2BMN, a large bipolar strain of 0.43% was achieved at 55 kV/cm, and the normalized strain reaches to 862 pm/V at a low driving electric field of 40 kV/cm. It was found that the substitution of BiMg_2/3Nb_1/3O₃ induces a transformation from ferroelectric to relaxor phase by disrupting the long range ferroelectric order. Therefore, as the external electric field was applied, a relaxor‐ferroelectric phase transition will be induced. This is contributed to the giant strain. The results above suggest that such a ternary composition is a promising candidate for application to actuator.     

Giant electromechanical strain response in lead‐free SrTiO3‐doped (Bi0.5Na0.5TiO3–BaTiO3)–LiNbO3 piezoelectric ceramics

Lead‐free 0.985[(0.94?x)Bi_0.5Na_0.5TiO₃–0.06BaTiO₃–xSrTiO₃]–0.015LiNbO₃ [(BNT–BT–xST)–LN, x=0‐0.05] piezoelectric ceramics were prepared using a conventional solid‐state reaction method. It was found that the long‐range ferroelectric order in the unmodified (BNT–BT)–LN ceramic was disrupted and transformed into the ergodic relaxor phase with the ST substitution, which was well demonstrated by the dramatic decrease in remnant polarization (P_r), coercive field (E_c), negative strain (S_neg) and piezoelectric coefficient (d₃₃). However, the degradation of the ferroelectric and piezoelectric properties was accompanied by a significant increase in the usable strain response. The critical composition (BNT–BT–0.03ST)–LN exhibited a maximum unipolar strain of ~0.44% and corresponding normalized strain, S_max/E_max of ~880 pm/V under a moderate field of 50 kV/cm at room temperature. This giant strain was associated with the coexistence of the ferroelectric and ergodic relaxor phases, which should be mainly attributed to the reversible electric‐field‐induced transition between the ergodic relaxor and ferroelectric phases. Furthermore, the large field‐induced strain showed relatively good temperature stability; the S_max/E_max was as high as ~490 pm/V even at 120°C. These findings indicated that the (BNT–BT–xST)–LN system would be a suitable environmental‐friendly candidate for actuator applications.     

Bi0.5Na0.5TiO3-BaTiO3-K0.5Na0.5NbO3:ZnO relaxor ferroelectric composites with high breakdown electric field and large energy storage properties

0.82[0.94Bi_0.5Na_0.5TiO₃-0.06BaTiO₃]-0.18K_0.5Na_0.5NbO₃:xZnO (BNT-BT-KNN:xZnO, x?=?0-0.40) relaxor composites were prepared and their electrical properties were investigated. The breakdown electric field increases with increasing ZnO content. For x?=?0 and x?=?0.40 samples, the maximum recoverable energy storage density is 0.74?J/cm³ and 1.03?J/cm³ while the maximum energy storage efficiency is 86.7% and 72.7% under the electric field of 9.0?kV/mm and 14.0?kV/mm, respectively. The recoverable energy storage density and efficiency of the composite vary less than 2.5% from 25?°C to 125?°C, which indicates temperature-insensitive energy storage performance. These results are discussed based on the ZnO-enhanced bulk resistivity and the ZnO-induced local electric field which suppresses the evolution of polar nanoregions.     

Large Strain Response and Fatigue‐Resistant Behavior in Ternary Bi0.5Na0.5TiO3–BaTiO3–Bi(Zn0.5Ti0.5)O3 Solid Solutions

A ternary solid solution (1 ? x)(0.88Bi_0.5Na_0.5TiO₃–0.12BaTiO₃)‐xBi(Zn_0.5Ti_0.5)O₃ (BNBZT, BNBZTx) was designed and fabricated using the traditional solid‐state reaction method. The temperature and composition dependence of dielectric, ferroelectric, piezoelectric, and fatigue properties were systematically investigated and a schematic phase diagram was proposed. The substitution with Bi(Zn_0.5Ti_0.5)O₃ was found to shift the phase transition (ferroelectric tetragonal to relaxor pseudocubic phase) to lower temperatures. At a critical composition x of 0.05, large electric‐field‐induced strain response with normalized strain S_max/E_max as high as 526 pm/V was obtained under a moderate field of 4 kV/mm around room temperature. The strain exhibited good temperature stability within the temperature range of 25°C–120°C. In addition, excellent fatigue‐resistant behavior was observed in the proposed BNBZT solid solution after 10⁶ bipolar cycles. These give the BNBZT system great potential as environmental friendly solid‐state actuator.     

Short crack fracture toughness in (1−x)(Na1/2Bi1/2)TiO3–xBaTiO3 relaxor ferroelectrics

The fracture toughness in the lead‐free relaxor ferroelectric (1?x)(Na_1/2Bi_1/2)TiO₃–xBaTiO₃ was investigated utilizing the surface crack in flexure method. To allow a comprehensive assessment, unpoled, and poled samples from the rhombohedral, the tetragonal, and the morphotropic phase regime were considered. It was found that the fracture toughness is up to 23% higher for the poled state. In order to cover the transition from ferroelectric to relaxor phase, the temperature dependence of 0.97(Na_1/2Bi_1/2)TiO₃–0.03BaTiO₃ was studied as well. Fracture toughness values of up to 2 MPam^1/2 were determined, which are considerably above data for lead zirconate titanate materials. The results are rationalized using a simple transformation toughening‐type model in conjunction with investigations into the ferroelastic behavior. The presented model can be applied without fitting parameters but utilizes measurements of the coercive stress and remanent strain as well as the elastic modulus.     

Dielectric Relaxor Evolution and Frequency‐Insensitive Giant Strains in (Bi0.5Na0.5)TiO3‐Modified Bi(Mg0.5Ti0.5)O3–PbTiO3 Ferroelectric Ceramics

The 0.45Bi(Mg_0.5Ti_0.5)O₃–(0.55 ? x)PbTiO₃–x(Bi_0.5Na_0.5)TiO₃ (BMT–PT–xBNT) ternary solid solution ceramics were prepared via a conventional solid‐state reaction method; the evolution of dielectric relaxor behavior and the electrostrain features were investigated. The XRD and dielectric measurements showed that all studied compositions own a single pseudocubic perovskite structure and undergo a diffuse‐to‐relaxor phase transition owing to the evolution of the domain from a frozen state to a dynamic state. The formation of the above dielectric relaxor behavior was further confirmed by a couple of measurements such as polarization loops, polarization current density curves, as well as bipolar strain loops. A large strain value of ~0.41% at a driving field of 7 kV/mm (normalized strain d₃₃* of ~590 pm/V) was obtained at room temperature for the composition with x = 0.32, which is located near the boundary between ergodic and nonergodic relaxor. Moreover, this electric field‐induced large strain was found to own a frequency‐insensitive characteristic.     

Impedance Spectroscopy of (Bi1/2Na1/2)TiO3–BaTiO3 Based High‐Temperature Dielectrics

The dielectric properties of CaZrO₃ (CZ) modified 0.94Bi_1/2Na_1/2TiO₃ (BNT)–0.06BaTiO₃ (BT) and 0.82(0.94BNT–0.06BT)–0.18(K_1/2Na_1/2)NbO₃ have been investigated by impedance spectroscopy over a wide temperature range. The presence of a highly polarizable phase in addition to a bulk response is revealed by electric modulus (M″) spectra in both systems. The relaxation frequency of the polar phase follows the Vogel–Fulcher law below the Burns temperature which decreases with increasing CZ content. The dc conductivity of the ceramics is dominated by the bulk response which follows the Arrhenius law with an activation energy ranging from 1.4 to 1.7 eV and has an oxygen partial pressure dependence consistent with n‐type semiconductivity. This information is pertinent to on‐going compositional development of relaxor‐based high‐temperature dielectrics.     

The Composition and Temperature‐Dependent Structure Evolution and Large Strain Response in (1−x)(Bi0.5Na0.5)TiO3−xBa(Al0.5Ta0.5)O3 Ceramics

The (1?x) (Bi_0.5Na_0.5)TiO₃?xBa(Al_0.5Ta_0.5)O₃((1?x)BNT‐xBAT) lead‐free piezoceramics was fabricated using a conventional solid‐state reaction method. The temperature and composition‐dependent strain behavior, dielectric, ferroelectric (FE), piezoelectric, and pyroelectric properties have been systematically investigated to develop lead‐free piezoelectric materials with large strain response for actuator application. As the BAT content increased, the FE order is disrupted resulting in a degradation of the remanent polarization, coercive field, and the depolarization temperature (T_d). A large strain of 0.36% with normalized strain d₃₃* = 448pm/V was obtained for the optimum composition x = 0.045 at room temperature. The bipolar and unipolar strains for the compositions x = 0.035 and x = 0.04 reach almost identical maximum values when the temperature is in the vicinity of their respective depolarization temperature (T_d). The Raman‐spectra analysis, macroscopic properties, thermal depolarization results, and temperature‐dependent relationships of both polarization and strain demonstrated that the origin of the large strain response for this investigated system is attributed to a field‐induced relaxor to FE phase transformation.     

Crack‐tip toughness of lead‐free (1−x)(Na1/2Bi1/2)TiO3–xBaTiO3 piezoceramics

Crack opening displacements were evaluated on semi‐elliptical indentation cracks in lead‐free (1?x)(Na_1/2Bi_1/2)TiO₃–xBaTiO₃ piezoceramics and a commercially available PZT ceramic. The observed crack‐tip toughness of NBT‐xBT was found to be substantially higher than for PZT. Two evaluations for the crack opening displacement were demonstrated and contrasted: A more elaborate three‐term‐approximation and a pragmatic utilization of the Irwin parabola.     

Electrostatic energy storage performances of La(Ni2/3Ta1/3)O3-modified Na0.5Bi0.5TiO3 lead-free ceramics

Ceramic capacitors with high electrostatic energy storage performances have captured much research interest in latest years. Sodium bismuth titanate (Na_0.5Bi_0.5TiO₃)-based ferroelectric ceramics show great potential due to their environment-friendly composition, high polarization, and excellent relaxor properties. However, the nonergodic relaxor state of Na_0.5Bi_0.5TiO₃-based ceramics hampers the decrement of remanent polarization, leading to poor energy storage performance. Herein, the (1 − x)Na_0.5Bi_0.5TiO₃–xLa(Ni_2/3Ta_1/3)O₃ ceramics were designed to generate the transformation between nonergodic and ergodic relaxor state. As a result, the ceramics exhibit improved dielectric relaxation, slim polarization–electric field loops, and flattened current–electric field curves due to highly dynamic polar nanoregions. Particularly, the 0.85Na_0.5Bi_0.5TiO₃–0.15La(Ni_2/3Ta_1/3)O₃ ceramics show large breakdown electric field E_b (345 kV/cm), high recoverable energy density W_rec (3.6 J/cm³), and efficiency η (80.6%), revealing potential applications in electrostatic energy storage.     

Lead-free BaTiO3-Bi0.5Na0.5TiO3-Na0.73Bi0.09NbO3 relaxor ferroelectric ceramics for high energy storage

A series of (1-x)(0.65BaTiO₃-0.35Bi_0.5Na_0.5TiO₃)-xNa_0.73Bi_0.09NbO₃ ((1-x)BBNT-xNBN) (x = 0–0.14) ceramics were designed and fabricated using the conventional solid-state sintering method. The microstructure, dielectric property, relaxor behavior and energy storage property were systematically investigated. X-ray diffraction results reveal a pure perovskite structure and dielectric measurements exhibit a relaxor behavior for the (1-x)BBNT-xNBN ceramics. The slim polarization electric field (P-E) loops were observed in the samples with x ≥ 0.02 and the addition of Na_0.73Bi_0.09NbO₃ (NBN) could decrease the remnant polarization (P_r) of the (1-x)BBNT-xNBN ceramics obviously. The sample with x = 0.08 exhibits the highest energy storage density of 1.70 J/cm³ and the energy storage efficiency of 82% at 172 kV/cm owing to its submicron grain size and high relative density. These results show that the (1-x)BBNT-xNBN ceramics may be promising lead-free materials for high energy storage density capacitors.