Selective solid-phase extraction using molecular imprinted polymer for the analysis of diethylstilbestrol

A simple imprinted amino-functionalized silica gel material was synthesized by combining a surface molecular imprinting technique with a sol–gel process for solid-phase extraction–high performance liquid chromatography (SPE–HPLC) determination of diethylstilbestrol (DES). Activated silica gel was used as the supporter and non-imprinted silica sorbent was synthesized without the addition of DES using the same procedure as that of DES-imprinted silica sorbent. Compared with non-imprinted polymer particles, the prepared DES-imprinted silica sorbent showed high adsorption capacity, significant selectivity, good site accessibility and fast binding kinetics for DES. The maximum static adsorption capacity of the DES-imprinted and non-imprinted silica sorbent for DES was 62.58 mg g⁻¹ and 19.89 mg g⁻¹, respectively. The relatively selective factor value of this DES-imprinted silica sorbent was 61.7 at the level of 50 mg L⁻¹. And the uptake kinetics was fairly rapid so that the adsorbent equilibrium was achieved within 10 min. Furthermore, the DES-imprinted polymers were used as the sorbent in solid-phase extraction to determine DES in fish samples. The MIP–SPE–HPLC method showed higher selectivity and good recoveries higher than 87.5% (R.S.D. 11.6%).     

Determination of Ge(IV) in rice in a mercury-coated glassy carbon electrode in the presence of catechol

Electrochemical adsorptive cathodic stripping voltammetry determination of Ge(IV) using the catechol complex on a mercury-coated (MC) electrode was prepared using a glassy carbon electrode (GCE), the peak potential of which was −0.5 V vs. Ag/AgCl on MCGCE. The various parameters of the catechol concentration, its pH, and others were optimized. The linear working ranges were obtained in the concentration of 2–700 μg L⁻¹ Ge(IV). The relative standard deviation at the Ge(IV) concentration of 50 μg L⁻¹ was 1.37% (n = 15) using the optimum condition, and the detection limit was found to be 0.6 μg L⁻¹ (8.26 × 10⁻⁹ M) (S/N = 3), with an adsorption time of 180 s. The Ge(IV) response was highly linear. This developed method was applied to Ge(IV) to determine the presence of rice grains.     

Effect of modifiers for As,Cu and Pb determinations in sugar-cane spirits by GF AAS

Palladium plus magnesium nitrates with and without Ir, Ru and W were evaluated for the simultaneous determination of As, Cu and Pb in cachaça by graphite furnace atomic absorption spectrometry. For 20 μL of sample, 5 μL Pd(NO₃)₂ and 3 μL Mg(NO₃)₂ dispensed together onto the Ir-coated platform of the THGA, analytical curves in the 0–30.0 μg L⁻¹ As, 0–1.50 mg L⁻¹ Cu and 0–60.0 μg L⁻¹ Pb were built up and typical linear correlation coefficients were always better than 0.999. The limit of detection was 1.30 μg L⁻¹ As, 140 μg L⁻¹ Cu and 0.90 μg L⁻¹ Pb. As, Cu and Pb contents in 10 cachaça samples agreed with those obtained by ICP-MS. Recoveries of spiked samples varied from 96% to 106% (As), 97% to 112% (Cu) and 92% to 108% (Pb). The relative standard deviation (n = 12) was typically 2.7%, 3.3% and 1.9%.     

Synthesis and application of a new functionalized resin for use in an on-line,solid phase extraction system for the determination of trace elements in waters and reference cereal materials by flame atomic absorption spectrometry

The synthesis and characterization of the resin Amberlite XAD-4 functionalized with 2,6-pyridinedicarboxaldehyde and its application in an on-line system for the preconcentration of cadmium, cobalt, copper, lead and manganese prior to determination using flame atomic absorption spectrometry (FAAS) is proposed. Metal ions retained on the modified resin were eluted using 1.0 mol L⁻¹ HNO₃ solution and aspirated directly to the nebulizer–burner system of a FAAS instrument using a flow injection system. Detection limits (3σ) were determined to be 0.13 μg L⁻¹ for Cd, 0.29 μg L⁻¹ for Cu, 0.23 μg L⁻¹ for Mn, 0.58 μg L⁻¹ for Co and 2.19 μg L⁻¹ for Pb using a 10 mL of water sample loading volume. The limits of detection would be 100 times higher with units of μg kg⁻¹ for the solid samples in which their dilution ratios as (volume/weight) were 100. Enrichment factors ranged from 23.6 to 28.9 (for Co and Mn, respectively). The proposed method was successfully applied to determination of the analytes in natural water samples and certified reference materials.     

Occurrence of patulin and its dietary intake through apple juice consumption by the Spanish population

A survey was conducted to determine levels and dietary intake of Patulin (PAT) from apple juices consumed in Spain. One hundred samples of apple juice were bought from distinct supermarkets. PAT was extracted by a liquid–liquid extraction technique and analysed with a micellar electrokinetic chromatography (MEKC) method. 66% of the samples contained PAT over the limit of detection of the method (0.7 μg L⁻¹). The PAT apple juice mean and median levels obtained were 19.4 and 4.8 μg L⁻¹, respectively, in a range between 0.7 and 118.7 μg L⁻¹. In 11% of the samples, PAT contamination exceeded the maximum permitted level of 50 μg L⁻¹ established by the EU regulation. In Spain, no significant variations were observed with respect to data published 15 years ago.     

Determination of aflatoxins in eggs,milk, meat and meat products using HPLC fluorescent and UV detectors

Raw and pasteurised sheep’s, cow’s and goat’s milk, eggs, and beef samples from different local markets in Jordan were collected during a period of 5 months (January through May 2007) and examined for aflatoxins B1(AFB1), B2(AFB2), G1(AFG1), G2(AFG2), M1(AFM1) and M2(AFM2). The samples were analysed with high performance liquid chromatography (HPLC) using UV and Fluorescent detectors. The analysed samples of milk collected in January were found to contain 0.56 μg L⁻¹ AFM1 and 0.1 μg L⁻¹ AFM2 whilst, the concentration of AFM1 and AFM2 was < 0.05 μg L⁻¹ for milk samples collected between March and May. The AFB1, AFB2, AFG1 and AFG2 contents in the analysed food products ranged from 1.10 to 8.32 μg L⁻¹ and 0.15 to 6.36 μg L⁻¹ in imported and fresh meat samples collected during March, respectively. The mean recovery for the HPLC method was 92% to 109% and the quantification levels were 50 ng L⁻¹ for AFM1 and AFM2. The AFM1 was found in 10% of the tested samples with concentrations between 0.08 and 1.1 μg kg⁻¹ and AFM2 was only found in 1.82% of the tested samples with a level of 0.1 μg kg⁻¹. The AFM1 levels in the examined foods were higher than the maximum level of AFM1 in liquid milk set by the European Community and Codex Alimentarius of 50 ng L⁻¹.     

Speciation of organic and inorganic selenium in selenium-enriched rice by graphite furnace atomic absorption spectrometry after cloud point extraction

A new method was developed for the determination of organic and inorganic selenium in selenium-enriched rice by graphite furnace atomic absorption spectrometry detection after cloud point extraction. Effective separation of organic and inorganic selenium in selenium-enriched rice was achieved by sequentially extracting with water and cyclohexane. Under the optimised conditions, the limit of detection (LOD) was 0.08 μg L⁻¹, the relative standard deviation (RSD) was 2.1% (c = 10.0 μg L⁻¹, n = 11), and the enrichment factor for selenium was 82. Recoveries of inorganic selenium in the selenium-enriched rice samples were between 90.3% and 106.0%. The proposed method was successfully applied for the determination of organic and inorganic selenium as well as total selenium in selenium-enriched rice.     

Chemiluminescence microflow injection analysis system on a chip for the determination of nitrite in food

A new microflow injection analysis (μFIA) system on a chip for the determination of nitrite is described. The chip is produced by using two transparent poly(methylmethacrylate) (PMMA) slices measured 50 × 40 × 5 mm, and the microchannels etched by CO₂ laser are 200 μm wide and 100 μm deep with the volume of reaction area about 1.8 μL. Nitrite is sensed by the chemiluminescence (CL) reaction of luminol with ferricyanide that is the product of the reaction of ferrocyanide with nitrite in acidic medium. The syringe pump with an accurate timer controls all reagents, including the sample. The linear range of the nitrite concentration is 8–100 μg L⁻¹ and the detection limit is 4 μg L⁻¹ (S/N = 3). The proposed method has good reproducibility with the relative standard deviation 4.1% for 50 μg L⁻¹ of nitrite (n = 9) and is very sensitive and simple. It has been successfully applied to the determination of nitrite in food.     

Molecularly imprinted solid-phase extraction coupled to liquid chromatography for determination of Sudan dyes in preserved beancurds

New molecularly imprinted microspheres synthesized by suspension polymerisation using phenylamine and naphthol as mimic template were successfully applied as selective sorbents for the solid-phase extraction used for the simultaneous determination of four Sudan dyes from preserved beancurd products. The obtained imprinted microspheres showed good recognition and selectivity to the four Sudan dyes in aqueous solution and the affinity could be easily controlled by adjusting the property of the solution. Under the selected experimental condition, the recoveries of the Sudan dyes in preserved beancurds at three spiked levels were ranged between 90.2-104.5% with the relative standard deviation of less than 6.8%. The limit of detection (LOD) and limit of quantification (LOQ) based on a signal-to-noise of 3 and 10 were in the range of 0.005-0.009 μg g⁻¹ and 0.015-0.030 μg g⁻¹, respectively. Comparing with alumina and C₁₈-based extraction, the selectivity and repeatability of molecularly imprinted solid-phase extraction (MISPE) were obviously improved. This method could be potentially applied for the determination of Sudan dyes in complicated food samples.     

Selective determination of copper and iron in various food samples by the solid phase extraction

The solid phase extraction method developed using N-benzoyl-N-phenylhydroxylamine as a chelating reagent and Amberlite XAD-1180 as an adsorbent was used for the determination of Cu(II) and Fe(III) in various food samples by flame atomic absorption spectrometry. The samples were digested by using nitric acid and hydrogen peroxide. The Cu concentrations ranged from 1.01 to 5.81 μg g⁻¹ in cereals, from 0.40 to 9.67 μg g⁻¹ in vegetable and fruits and from 0.37 to 0.70 μg g⁻¹ in infusions while the Fe concentrations ranged from 7.48 to 34.3 μg g⁻¹ in cereals, from 5.74 to 260 μg g⁻¹ in vegetable and fruits, from 1.63 to 5.12 μg g⁻¹ in infusions and from 0.24 to 1.56 mg L⁻¹ in beverage samples. The Cu and Fe concentrations found were compared with the results obtained from the other food studies in the world.     

Pico molar assay of riboflavin in human urine using voltammetry

Using a new type of DNA and carbon nano tube (CNT) mixed paste electrode using cyclic and square wave anodic stripping voltammetric (SWASV) methods, this study presents an assay of riboflavin (RF) under optimum conditions. Results of the experiment yielded a low working concentration range of nanograms with 1–10 and 10–170 ng L⁻¹ and 5–105 μg L⁻¹, at an accumulation time of 80 s in a 0.1 M H₃PO₄ electrolyte solution. A relative standard deviation of 30 μg L⁻¹ was observed at an accuracy level of 0.1164% (n = 15) under optimum conditions. The detection limit (S/N) was pegged at 0.2 ng L⁻¹ (5.31 × 10⁻¹³ mol L⁻¹ RF). The proposed method was successfully applied to an actual human urine and drug sample, and can be applied to assays of other biological samples.     

Tungsten permanent chemical modifier with co-injection of Pd(NO3)2 + Mg(NO3)2 for direct determination of Pb in vinegar by graphite furnace atomic absorption spectrometry

A tungsten carbide coating on the integrated platform of a transversely heated graphite atomizer (THGA^®) used together with Pd(NO₃)₂ + Mg(NO₃)₂ as modifier is proposed for the direct determination of lead in vinegar by graphite furnace atomic absorption spectrometry. The optimized heating program (temperature, ramp time, hold time) of atomizer involved drying stage (110 °C, 5 s, 30 s; 130 °C, 5 s, 30 s), pyrolysis stage (1000 °C, 15 s, 30 s), atomization stage (1800 °C, 0 s, 5 s) and clean-out stage (2450 °C, 1 s, 3 s). For 10 μL of vinegar delivered into the atomizer and calibration using working standard solutions (2.5–20.0 μg L⁻¹ Pb) in 0.2% (v/v) HNO₃, analytical curve with good linear correlation (r = 0.9992) was established. The characteristic mass was 40 pg Pb and the lifetime of the tube was around 730 firings. The limit of detection (LOD) was 0.4 μg L⁻¹ and the relative standard deviations (n = 12) were typically <8% for a sample containing 25 μg L⁻¹ Pb. Accuracy of the proposed method was checked after direct analysis of 23 vinegar samples. A paired t-test showed that results were in agreement at 95% confidence level with those obtained for acid-digested vinegar samples. The Pb levels varied from 2.8 to 32.4 μg L⁻¹. Accuracy was also checked by means of addition/recovery tests and recovered values varied from 90% to 110%. Additionally, two certified reference materials were analyzed and results were in agreement with certified values at a 95% confidence level.     

Development of a fast multiresidue method for the determination of pesticides in dry samples (wheat grains,flour and bran) using QuEChERS based method and GC–MS

In this study a multiresidue method for the determination of 24 pesticides in wheat, white flour and bran using gas chromatography coupled to mass spectrometry with negative chemical ionisation and selected ion monitoring (GC–MS (NCI–SIM)) was developed and validated. The QuEChERS method was used for the extraction of different pesticides. The method was validated evaluating the following parameters: linearity, limit of detention, limit of quantification, matrix effect as well as precision and accuracy, evaluating the percentage of recovery at four different spike levels. The linear range used in the calibration curves was from 1.0 to 100 μg L⁻¹ for wheat and 2.0 to 200 μg L⁻¹ for flour and bran, both with values of r² > 0.99. The recoveries had been considered satisfactory presenting values between 70% and 120% with RSD < 20% for the majority of compounds.     

Salt-assisted liquid–liquid microextraction for the determination of iodine in table salt by high-performance liquid chromatography-diode array detection

2-Iodosobenzoate and N,N-dimethylaniline have been used at pH 6.4 for selective conversion of iodide to 4-iodo-N,N-dimethylaniline which was extracted with ethanol, when the phase separation occurred by addition of ammonium sulphate, a process called salt-assisted liquid–liquid microextraction (SALLME), and analysed by high-performance liquid chromatography-diode array detection. Iodate was reduced to iodide before derivatisation. The method has been optimised for extracting solvent, salt for phase separation, and reaction time. A linear calibration was obtained for 10 μg-10 mg L⁻¹ of iodide with correlation coefficient of 0.9989 and limit of detection of 3.7 μg L⁻¹. The SALLME produced 280-fold enrichment of the derivative. The commercial iodised table salt samples have been found highly inhomogeneous; the RSD in analysis of different aliquots of the same sample ranged 18.0-78.1%. The average recovery of spiked iodide to real samples was 98.4% with an average RSD of 7.9% (range 5.2-12.4%).     

Immobilization of pepsin on chitosan beads

In this study, chitosan beads were prepared by using a cross-linking agent and the resulting beads were employed in immobilization process. Studies on free and immobilized pepsin systems for determination of optimum temperature, optimum pH, thermal stability, pH stability, operational stability, storage stability and kinetic parameters were carried out. The optimum temperature interval for free pepsin and immobilized pepsin were 30–40 and 40–50 °C, respectively. Free and immobilized pepsin showed higher activity at pH 2.0–4.0. Apparent K_m = 12.0 g L⁻¹ haemoglobin (1.56 mM tyrosine) and V_max = 5220 μmol (mg protein min)⁻¹ values were obtained for free pepsin, while apparent K_m = 20.0 g L⁻¹ haemoglobin (2.16 mM tyrosine) and V_max = 2780 μmol (mg protein min)⁻¹ values were obtained for immobilized pepsin. Thermal stability and storage stability of immobilized pepsin were higher than that of free pepsin. Milk clotting activity was used for evaluation of the applicability of pepsin immobilization to industrial process. Optimum milk clotting temperature was found as 40 °C for free pepsin and 50 °C for immobilized pepsin.     

Trace element levels in honeys from different regions of Turkey

A survey of 25 honey samples from different botanical origin, collected all over the Turkey was conducted to assess their trace element contents. The aim of this study was to determine the levels of cadmium (Cd), lead (Pb), iron (Fe), manganese (Mn), copper (Cu), nickel (Ni), chromium (Cr), zinc (Zn), aluminium (Al) and selenium (Se) in honey samples from different regions of Turkey. Trace element contents were determined by a flame and graphite furnace atomic absorption spectrometry technique after dry-ashing, microwave digestion and wet-digestion. The accuracy of the method was corrected by the standard reference material, NIST-SRM 1515 Apple leaves. The contents of trace elements in honey samples were in the range of 0.23–2.41 μg g⁻¹, 0.32–4.56 μg g⁻¹, 1.1–12.7 μg g⁻¹, 1.8–10.2 μg g⁻¹, 8.4–105.8 μg kg⁻¹, 2.6–29.9 μg kg⁻¹, 2.4–37.9 μg kg⁻¹, 0.9–17.9 μg kg⁻¹, 83–325 μg kg⁻¹ and 38–113 μg kg⁻¹ for Cu, Mn, Zn, Fe, Pb, Ni, Cr, Cd, Al and Se, respectively. Iron was the most abundant element while cadmium was the lowest element in the Turkish honeys surveyed. The results showed that trace element concentrations in the honeys from different regions were generally correlated with the degree of trace element contamination of the environment.     

Determination of pyrethroids in porcine tissues by matrix solid-phase dispersion extraction and high-performance liquid chromatography

An effective matrix solid-phase dispersion (MSPD) extraction for determination of two pyrethroids (cypermethrin and deltamethrin) in porcine tissues (liver, muscle, heart and kidney) is described. A neutral alumina-based MPSD column was used for extraction of analytes. The high-performance liquid chromatography and ultraviolet detector was applied using a reverse-phase C₁₈ column and acetonitrile-water (85:15, v/v) was used as mobile phase. The good linear fit curve ranging from 0.05 to 50 μg mL⁻¹ for cypermethrin (CM) and deltamethrin (DM) was obtained with a regression coefficient (r) of 0.999. Recoveries at 0.2 and 0.5 μg g⁻¹ levels were between 83.5% and 109%. The limits of detection and quantification were: 0.01 and 0.026 μg g⁻¹ for CM, 0.017 and 0.056 μg g⁻¹ for DM, respectively. The proposed method was successfully applied to the determination of the pyrethroids in porcine tissues.     

Preparation of galacto-oligosaccharides using membrane reactor

Galacto-oligosaccharides (GOS) have many biological functions. They are produced from lactose by a glycosyl transfer of one or more d-galactosyl units onto the d-galactose moiety of lactose catalysed by β-galactosidase. This reaction can proceed in batch or in continuous system. Membrane reactor with ultrafiltration ceramic membrane (150 kDa) was used and batch system as well. Lactose in phosphate buffer (197.9 g L⁻¹), recombined whey (197 g L⁻¹) and evaporated ultrafiltration permeate (200.7 g L⁻¹) were used as substrates. The used concentration of enzyme Maxilact LX 5000 was 6 U mL⁻¹. The highest concentration of GOS in buffer was reached after 30 min of batch reaction and it was 25.5 g L⁻¹, for recombined whey it was 31.1 g L⁻¹ and for ultrafiltration permeate it was 32.9 g L⁻¹. For continuous process was obtained 8.8 g L⁻¹ of GOS for buffer and 21.0 g L⁻¹ for recombined whey and 16.7 g L⁻¹ of GOS for ultrafiltration permeate.     

Comparison of positive and negative ion detection of tea catechins using tandem mass spectrometry and ultra high performance liquid chromatography

Tea catechins are an important group of natural compounds associated with health promoting effects and desired commodities for the growing market of dietary supplements and functional foods. Consequently these compounds attract more interest of research groups worldwide. A reliable quantitative analysis of tea catechins is essential for human intervention studies, manufacturers of dietary supplements and quality control by authorities. UHPLC–ESI-MS/MS analytical method was chosen due to rapid runtime, high sensitivity and selectivity. The chromatographic separation of eight tea catechins was achieved within 2.5 min on C₁₈ BEH analytical column (100 mm × 2.1 mm i.d.; 1.7 μm), whilst the gradient elution mode was employed using water:methanol mobile phase with addition of volatile organic acid. The concentration of organic acids in the mobile phase was optimised within the range of 0.01–0.1% (v/v). High sensitivities were achieved in positive (10.2-16.8 fmol/inj.) and negative ion detection mode (102.1-168.1 fmol/inj.), through accurate and complex tuning of MS parameters. The UHPLC-ESI-MS/MS method was validated in terms of linearity (>0.9997; >0.9990), range (0.02–2.40 mg L⁻¹; 0.15-24.00 mg L⁻¹), LOD (3.0–4.8 μg L⁻¹; 30.1–48.0 μg L⁻¹), LOQ (9.9–15.8 μg L⁻¹; 150.5-240.0 μg L⁻¹), intra-day precision (4.4-7.1% RSD; 3.3-5.1% RSD), accuracy (94.06-113.7%; 89.5-108.4%), retention time repeatability (0.0-0.5% RSD; 0.0-0.6% RSD), and peak area repeatability (1.2-4.0% RSD; 2.4-3.5% RSD) for positive and negative ion detection modes, respectively. The statistical comparison of the quantitative results obtained in positive and negative ion detection mode was performed.     

Ethyl-carbamate determination by gas chromatography–mass spectrometry at different stages of production of a traditional Brazilian spirit

Ethyl carbamate (EC), which is probably carcinogenic to humans, can be produced during the alcoholic fermentation of sugar-cane juice to give cachaça. The stages to produce cachaça are obtainment of sugar-cane juice, sugar-cane fermentation to wine, and obtainment of distilled fractions and residue. In order to investigate the presence of EC in the wine and in the fractions of the distillation process, as well as in the vinasse (the residue left after distillation), gas chromatography–mass spectrometry was employed. After the fermentation phase, the wine showed an average content of 122 mg L⁻¹ of EC. Average EC content in distilled fractions was 59.7 mg L⁻¹ for head, 52 μg·L⁻¹ for heart and 1.57 mg L⁻¹ for tail. EC content was 53.1 mg L⁻¹ for vinasse. The results showed that it is essential to separate the head and tail fractions to ensure cachaça quality, with respect to EC content.