Effect of modifiers for As,Cu and Pb determinations in sugar-cane spirits by GF AAS

Palladium plus magnesium nitrates with and without Ir, Ru and W were evaluated for the simultaneous determination of As, Cu and Pb in cachaça by graphite furnace atomic absorption spectrometry. For 20 μL of sample, 5 μL Pd(NO₃)₂ and 3 μL Mg(NO₃)₂ dispensed together onto the Ir-coated platform of the THGA, analytical curves in the 0–30.0 μg L⁻¹ As, 0–1.50 mg L⁻¹ Cu and 0–60.0 μg L⁻¹ Pb were built up and typical linear correlation coefficients were always better than 0.999. The limit of detection was 1.30 μg L⁻¹ As, 140 μg L⁻¹ Cu and 0.90 μg L⁻¹ Pb. As, Cu and Pb contents in 10 cachaça samples agreed with those obtained by ICP-MS. Recoveries of spiked samples varied from 96% to 106% (As), 97% to 112% (Cu) and 92% to 108% (Pb). The relative standard deviation (n = 12) was typically 2.7%, 3.3% and 1.9%.     

Salt-assisted liquid–liquid microextraction for the determination of iodine in table salt by high-performance liquid chromatography-diode array detection

2-Iodosobenzoate and N,N-dimethylaniline have been used at pH 6.4 for selective conversion of iodide to 4-iodo-N,N-dimethylaniline which was extracted with ethanol, when the phase separation occurred by addition of ammonium sulphate, a process called salt-assisted liquid–liquid microextraction (SALLME), and analysed by high-performance liquid chromatography-diode array detection. Iodate was reduced to iodide before derivatisation. The method has been optimised for extracting solvent, salt for phase separation, and reaction time. A linear calibration was obtained for 10 μg-10 mg L⁻¹ of iodide with correlation coefficient of 0.9989 and limit of detection of 3.7 μg L⁻¹. The SALLME produced 280-fold enrichment of the derivative. The commercial iodised table salt samples have been found highly inhomogeneous; the RSD in analysis of different aliquots of the same sample ranged 18.0-78.1%. The average recovery of spiked iodide to real samples was 98.4% with an average RSD of 7.9% (range 5.2-12.4%).     

Analysis of potential adulteration in herbal medicines and dietary supplements for the weight control by capillary electrophoresis

Four different phytopharmaceutical dosage forms for use in weight control programs were analyzed. Two different ground herbal blends and their correspondent infusions, a capsule and a tincture were investigated for the presence of compounds used as adulterants in these products. A capillary electrophoresis (CE) method was developed and validated. The optimized experimental conditions were: BGE, sodium tetraborate buffer 20 mM, pH 9.2, voltage applied 30 kV, capillary temperature 25 °C, injection sample at 0.5 Psi during 5 s. Ephedrine, norephedrine, caffeine and furosemide were baseline separated in less than 7 min; the migration times were found to be 2.65, 2.90, 3.75 and 6.58 min, respectively. The analysis showed in sample 3 concentrations of 0.45 ± 0.03 mg g⁻¹ (ephedrine), 0.33 ± 0.02 mg g⁻¹ (norephedrine), 1.09 ± 0.41 mg g⁻¹ (caffeine) and 0.80 ± 0.17 mg g⁻¹ (furosemide). Caffeine content in samples 1, 2 and 4 was 0.61 ± 0.06 mg g⁻¹, 15.66 ± 1.05 mg g⁻¹ and 2.27 ± 0.13 mg ml⁻¹, respectively. Linearity was obtained in the concentration range of 1–1000 μg ml⁻¹. Limits of detection (LOD) and quantification (LOQ) were determined as 0.42 μg ml⁻¹ and 1.40 μg ml⁻¹ (ephedrine), 0.47 μg ml⁻¹ and 1.40 μg ml⁻¹ (norephedrine), 0.12 μg ml⁻¹ and 0.48 μg ml⁻¹ (caffeine), 0.22 μg ml⁻¹ and 0.73 μg ml⁻¹ (furosemide).     

Analysis of some selected catechins and caffeine in green tea by high performance liquid chromatography

Green tea seems to have a positive impact on health due to the catechins-found as flavanols. Thus, the present study was aimed to develop a low cost reversed phase high performance liquid chromatographic (HPLC) method for simultaneous determination of flavanol contents, namely catechin (C), epicatechin (EC), epigallocatechin (EGC), epicatechin 3-gallate (ECG) and epigallocatechin 3-gallate (EGCG) and caffeine in 29 commercial green tea samples available in a Saudi Arabian local market. A C-18 reversed-phase column, acetonitrile–trifluoroacetic acid as a mobile phase, coupled with UV detector at 205 nm, was successfully used for precise analysis of the tested analytes in boiled water of digested tea leaves. The average values of N (No. of theoretical plates), HETP (height equivalent of theoretical plates) and R_s (separation factor) (at 10 μg ml⁻¹ of the catechins EC, EGC, EGCG and ECG) were 2.6 × 10³ ± 1.2 × 10³, 1.7 × 10⁻³ ± 4.7 × 10⁻⁴ cm and 1.7 ± 5.53 × 10⁻², respectively. The developed HPLC method demonstrated excellent performance, with low limits of detection (LOD) and quantification (LOQ) of the tested catechins of 0.004–0.05 μg ml⁻¹ and 0.01–0.17 μg ml⁻¹, respectively, and recovery percentages of 96–101%. The influence of infusion time (5–30 min) and temperature on the content of the flavanols was investigated by HPLC. After a 5 min infusion of the tea leaves, the average concentrations of caffeine, catechin, EC, EGC, ECG and EGCG were found to be in the ranges 0.086–2.23, 0.113–2.94, 0.58–10.22, 0.19–24.9, 0.22–13.9 and 1.01–43.3 mg g⁻¹, respectively. The contents of caffeine and catechins followed the sequence: EGCG > EGC > ECG > EC > C > caffeine. The method was applied satisfactorily for the analysis of (+)-catechin, even at trace and ultra trace concentrations of catechins. The method was rapid, accurate, reproducible and ideal for routine analysis.     

Effect of foliar application of selenium on its uptake and speciation in carrot

Carrot (Daucus carota) shoots were enriched by selenium using foliar application. Solutions of sodium selenite or sodium selenate at 10 and 100 μg Se ml⁻¹, were sprayed on the carrot leaves and the selenium content and uptake rate of selenium were estimated by ICP–MS analysis. Anion and cation exchange HPLC were tailored to and applied for the separation of selenium species in proteolytic extracts of the biological tissues using detection by ICP–MS or ESI–MS/MS. Foliar application of solutions of selenite or selenate at 100 μg Se ml⁻¹ resulted in a selenium concentration of up to 2 μg Se g⁻¹ (dry mass) in the carrot root whereas the selenium concentration in the controls was below the limit of detection at 0.045 μg Se g⁻¹ (dry mass). Selenate-enriched carrot leaves accumulated as much as 80 μg Se g⁻¹ (dry mass), while the selenite-enriched leaves contained approximately 50 μg Se g⁻¹ (dry mass). The speciation analyses showed that inorganic selenium was present in both roots and leaves. The predominant metabolised organic forms of selenium in the roots were selenomethionine and γ-glutamyl-selenomethyl-selenocysteine, regardless of which of the inorganic species were used for foliar application. Only selenomethionine was detected in the carrot leaves. The identity of selenomethionine contained in carrot roots and leaves was successfully confirmed by HPLC–ESI–MS/MS.     

Ethyl-carbamate determination by gas chromatography–mass spectrometry at different stages of production of a traditional Brazilian spirit

Ethyl carbamate (EC), which is probably carcinogenic to humans, can be produced during the alcoholic fermentation of sugar-cane juice to give cachaça. The stages to produce cachaça are obtainment of sugar-cane juice, sugar-cane fermentation to wine, and obtainment of distilled fractions and residue. In order to investigate the presence of EC in the wine and in the fractions of the distillation process, as well as in the vinasse (the residue left after distillation), gas chromatography–mass spectrometry was employed. After the fermentation phase, the wine showed an average content of 122 mg L⁻¹ of EC. Average EC content in distilled fractions was 59.7 mg L⁻¹ for head, 52 μg·L⁻¹ for heart and 1.57 mg L⁻¹ for tail. EC content was 53.1 mg L⁻¹ for vinasse. The results showed that it is essential to separate the head and tail fractions to ensure cachaça quality, with respect to EC content.     

Rapid quantitation of curcumin in turmeric via NMR and LC–tandem mass spectrometry

A rapid, sensitive and accurate ¹H NMR method has been developed for the quantitation of curcumin isolated from Curcuma longa rhizome (turmeric) extract, the results of which were compared with a validated LC–MS/MS method. The relative standard deviations of the methods were found to be 2.49% and 3.48% for the ¹H NMR and LC–MS/MS methods, respectively. The correlation coefficients were 0.998 for ¹H NMR and 0.995 for LC–MS/MS assay in the calibration range. The recoveries at 5 mg mL⁻¹ and 50 μg mL⁻¹ concentrations averaged to 99–101% for both techniques, respectively. The uncertainty of the measurement of curcumin via ¹H NMR spectroscopy was determined to be 5.80% while in LC–ESI-MS/MS method was 7.38%.     

Distribution and migration study of pesticides between peel and pulp in grape by online gel permeation chromatography–gas chromatography/mass spectrometry

A multi-residue method for the analysis of 175 pesticides was developed by online gel permeation chromatography–gas chromatography/mass spectrometry (GPC–GC/MS) to study pesticide distribution and migration between peel and pulp in grape. The separated peel and pulp samples were extracted by acetonitrile after fortified with chlorpyrifos-d₁₀ isotope internal standard. The extract was first purified by solid phase distribution sorbent of primary secondary amine (PSA) and then detected by online GPC–GC/MS. At the spiking levels of 10, 50 and 200 μg kg⁻¹, 73.7%, 94.3% and 98.9% of the pesticides, respectively, presented recoveries between 70% and 120%. The ratios were 91.4%, 94.9% and 92.0%, respectively, for the relative standard deviations (RSDs) bellow 15%. Limits of detection (LODs) for the pesticides in pulp were below 10 μg kg⁻¹. Pesticides were separated to four groups according to the distribution ratios (peel/whole grape) of 100%, 80–99.9%, 50–80% and 0–50% in peel. Relationship between the pesticide distribution and corresponding regulation of EU maximum residue level (MRL) was discussed. Six factors influencing the pesticides distribution and migration between peel and pulp were discussed. Weak linear correlation between the pesticide solubility in water (20 °C) and the distribution ratios (lowest and average) in peel was found for most of the detected pesticides with solubility less than 200 mg L⁻¹.     

Occurrence of patulin and its dietary intake through apple juice consumption by the Spanish population

A survey was conducted to determine levels and dietary intake of Patulin (PAT) from apple juices consumed in Spain. One hundred samples of apple juice were bought from distinct supermarkets. PAT was extracted by a liquid–liquid extraction technique and analysed with a micellar electrokinetic chromatography (MEKC) method. 66% of the samples contained PAT over the limit of detection of the method (0.7 μg L⁻¹). The PAT apple juice mean and median levels obtained were 19.4 and 4.8 μg L⁻¹, respectively, in a range between 0.7 and 118.7 μg L⁻¹. In 11% of the samples, PAT contamination exceeded the maximum permitted level of 50 μg L⁻¹ established by the EU regulation. In Spain, no significant variations were observed with respect to data published 15 years ago.     

Dispersive liquid–liquid microextraction for the determination of organochlorine pesticides residues in honey by gas chromatography-electron capture and ion trap mass spectrometric detection

A simple dispersive liquid–liquid microextraction (DLLME) protocol for the determination of 15 organochlorine pesticides residues in honey is proposed. The selected pesticides were separated using gas chromatography and detected by electron capture (ECD) or ion trap mass spectrometry (GC-IT/MS). Several parameters affecting the extraction efficiency namely type and volume of organic extraction solvent, type and volume of disperser solvent, sample pH, ionic strength, extraction time and centrifugation speed were systematically investigated. The final DLLME protocol involved the addition of 750 μL acetonitrile (disperser) and 50 μL chloroform (extraction solvent) into a 5 mL aqueous honey solution followed by centrifugation. The sedimented organic phase (chloroform) were analysed directly by GC-IT/MS or evaporated and reconstituted in acetonitrile prior to the GC-ECD analysis. The analytical performance of the GC-ECD and GC-IT/MS methods was compared and discussed. Under the selected experimental conditions, the enrichment factors varied between of 36 and 114. The limits of detection (LOD) were in the range of 0.02–0.15 μg L⁻¹ (0.4–3 ng g⁻¹) for GC-ECD and 0.01–0.2 μg L⁻¹ (0.2–4 ng g⁻¹) for GC-IT/MS which is adequate to verify compliance of products to legal tolerances. The proposed method was applied to the analysis of the selected organochlorine pesticides residues in various honey samples obtained from Greek region. Mean recoveries were ranged from 75% to 119% while the precision was better than 20% in both methodologies.     

Analysis of multi-pesticide residues in the foods of animal origin by GC–MS coupled with accelerated solvent extraction and gel permeation chromatography cleanup

A new analytical method was developed to simultaneously determine residues of 109 pesticides (including isomers) in the foods of animal origin. Acetonitrile was selected for accelerated solvent extraction (ASE) for effectively extracting the pesticides from the fatty samples. The cleanup was performed with an automated gel permeation chromatography (GPC) cleanup system. The prepared samples were analysed with GC–MS in the selected ion monitoring mode (SIM) using one target and two qualitative ions for each analyte. Chlorpyrifos-d₁₀ was used as an internal standard. The lowest limit of detection was 0.3 μg kg⁻¹ for some pesticides. The recoveries and relative standard deviations (RSDs) were checked by spiking untreated samples with pesticides at 0.05, 0.1 and 0.2 mg kg⁻¹. The average recoveries of most pesticides were from 62.6% to 107.8%. The precision values expressed as RSD were all ?20.5% (n = 6). Good linearity (r ? 0.99) was observed between 0.05 and 1.5 μg mL⁻¹.     

Synthesis and application of a new functionalized resin for use in an on-line,solid phase extraction system for the determination of trace elements in waters and reference cereal materials by flame atomic absorption spectrometry

The synthesis and characterization of the resin Amberlite XAD-4 functionalized with 2,6-pyridinedicarboxaldehyde and its application in an on-line system for the preconcentration of cadmium, cobalt, copper, lead and manganese prior to determination using flame atomic absorption spectrometry (FAAS) is proposed. Metal ions retained on the modified resin were eluted using 1.0 mol L⁻¹ HNO₃ solution and aspirated directly to the nebulizer–burner system of a FAAS instrument using a flow injection system. Detection limits (3σ) were determined to be 0.13 μg L⁻¹ for Cd, 0.29 μg L⁻¹ for Cu, 0.23 μg L⁻¹ for Mn, 0.58 μg L⁻¹ for Co and 2.19 μg L⁻¹ for Pb using a 10 mL of water sample loading volume. The limits of detection would be 100 times higher with units of μg kg⁻¹ for the solid samples in which their dilution ratios as (volume/weight) were 100. Enrichment factors ranged from 23.6 to 28.9 (for Co and Mn, respectively). The proposed method was successfully applied to determination of the analytes in natural water samples and certified reference materials.     

Determination of aflatoxins in eggs,milk, meat and meat products using HPLC fluorescent and UV detectors

Raw and pasteurised sheep’s, cow’s and goat’s milk, eggs, and beef samples from different local markets in Jordan were collected during a period of 5 months (January through May 2007) and examined for aflatoxins B1(AFB1), B2(AFB2), G1(AFG1), G2(AFG2), M1(AFM1) and M2(AFM2). The samples were analysed with high performance liquid chromatography (HPLC) using UV and Fluorescent detectors. The analysed samples of milk collected in January were found to contain 0.56 μg L⁻¹ AFM1 and 0.1 μg L⁻¹ AFM2 whilst, the concentration of AFM1 and AFM2 was < 0.05 μg L⁻¹ for milk samples collected between March and May. The AFB1, AFB2, AFG1 and AFG2 contents in the analysed food products ranged from 1.10 to 8.32 μg L⁻¹ and 0.15 to 6.36 μg L⁻¹ in imported and fresh meat samples collected during March, respectively. The mean recovery for the HPLC method was 92% to 109% and the quantification levels were 50 ng L⁻¹ for AFM1 and AFM2. The AFM1 was found in 10% of the tested samples with concentrations between 0.08 and 1.1 μg kg⁻¹ and AFM2 was only found in 1.82% of the tested samples with a level of 0.1 μg kg⁻¹. The AFM1 levels in the examined foods were higher than the maximum level of AFM1 in liquid milk set by the European Community and Codex Alimentarius of 50 ng L⁻¹.     

Trace element levels in honeys from different regions of Turkey

A survey of 25 honey samples from different botanical origin, collected all over the Turkey was conducted to assess their trace element contents. The aim of this study was to determine the levels of cadmium (Cd), lead (Pb), iron (Fe), manganese (Mn), copper (Cu), nickel (Ni), chromium (Cr), zinc (Zn), aluminium (Al) and selenium (Se) in honey samples from different regions of Turkey. Trace element contents were determined by a flame and graphite furnace atomic absorption spectrometry technique after dry-ashing, microwave digestion and wet-digestion. The accuracy of the method was corrected by the standard reference material, NIST-SRM 1515 Apple leaves. The contents of trace elements in honey samples were in the range of 0.23–2.41 μg g⁻¹, 0.32–4.56 μg g⁻¹, 1.1–12.7 μg g⁻¹, 1.8–10.2 μg g⁻¹, 8.4–105.8 μg kg⁻¹, 2.6–29.9 μg kg⁻¹, 2.4–37.9 μg kg⁻¹, 0.9–17.9 μg kg⁻¹, 83–325 μg kg⁻¹ and 38–113 μg kg⁻¹ for Cu, Mn, Zn, Fe, Pb, Ni, Cr, Cd, Al and Se, respectively. Iron was the most abundant element while cadmium was the lowest element in the Turkish honeys surveyed. The results showed that trace element concentrations in the honeys from different regions were generally correlated with the degree of trace element contamination of the environment.     

Selective determination of copper and iron in various food samples by the solid phase extraction

The solid phase extraction method developed using N-benzoyl-N-phenylhydroxylamine as a chelating reagent and Amberlite XAD-1180 as an adsorbent was used for the determination of Cu(II) and Fe(III) in various food samples by flame atomic absorption spectrometry. The samples were digested by using nitric acid and hydrogen peroxide. The Cu concentrations ranged from 1.01 to 5.81 μg g⁻¹ in cereals, from 0.40 to 9.67 μg g⁻¹ in vegetable and fruits and from 0.37 to 0.70 μg g⁻¹ in infusions while the Fe concentrations ranged from 7.48 to 34.3 μg g⁻¹ in cereals, from 5.74 to 260 μg g⁻¹ in vegetable and fruits, from 1.63 to 5.12 μg g⁻¹ in infusions and from 0.24 to 1.56 mg L⁻¹ in beverage samples. The Cu and Fe concentrations found were compared with the results obtained from the other food studies in the world.     

Chemical composition of cultivated seaweed Ulva clathrata (Roth) C. Agardh

Samples of cultivated Ulva clathrata were collected from a medium scale system (MSS, 1.5 × 1.5 m tank), or from a large scale system (LSS, 0.8 ha earthen pond). MSS samples were dried directly while the LSS sample was washed in freshwater and pressed before drying. Crude protein content ranged 20–26%, essential amino acids accounting for 32–36% of crude protein. The main analysed monosaccharides were rhamnose (36–40%), uronic acids (27–29%), xylose (10–13%) and glucose (10–16%). Some notable variations between MSS and LSS samples were observed for total dietary fibre (26% vs 41%), saturated fatty acids (31% vs 51%), PUFAS (33% vs 13%), carotenoids (358 vs 169 mg kg⁻¹ dw) and for Ca (9 vs 19 g kg⁻¹), Fe (0.6 vs 4.2 g kg⁻¹), Cu (44 vs 14 mg kg⁻¹), Zn (93 vs 17 mg kg⁻¹) and As (2 vs 9 mg kg⁻¹). The chemical composition of U. clathrata indicates that it has a good potential for its use in human and animal food.     

Simplified pesticide multiresidues analysis in fish by low-temperature cleanup and solid-phase extraction coupled with gas chromatography/mass spectrometry

A simple and fast method for the simultaneous analysis of thiobencarb, deltamethrin and 19 organochlorine pesticide residues in fish by gas chromatography–mass spectrometry was investigated in this study. Samples are extracted with acetonitrile. Most of lipids in the extract are eliminated by low-temperature cleanup, prior to solid-phase extraction cleanup. The lipids extracted from the fish samples were easily removed without any significant losses of the pesticides. Aminopropyl (NH₂) cartridge was effective to eliminate the remaining interference. Spiked experiments were carried out to determine the recovery, precision and limits of detection (LODs) of the method. The method detection limits ranged from 0.5 μg kg⁻¹ to 20 μg kg⁻¹, whilst recoveries of the pesticides were in the range of 81.3–113.7% with relative standard deviations ?13.5% at a spiked concentration of 0.05 mg kg⁻¹, 0.02 mg kg⁻¹ and 0.1 mg kg⁻¹. The newly developed method is demonstrated to give efficient recoveries and LODs for detecting pesticide multiresidues in fish.     

Analyses of selected non-authorized insecticides in peppers by gas chromatography/mass spectrometry and gas chromatography/tandem mass spectrometry

Two methods based on gas chromatography coupled with mass spectrometry and tandem mass spectrometry analyzers are described for the identification, confirmation and quantitation of two EU-banned insecticides: isocarbophos and isofenphos-methyl, detected in recent monitoring programmes in pepper samples. The proposed methodologies involved a liquid–liquid extraction with acetonitrile followed by a cleanup step by dispersive solid-phase extraction using primary–secondary amine as sorbent material. Recovery studies performed on peppers spiked at different fortification levels (10 and 50 μg kg⁻¹) yielded average recoveries in the range 85–98% with RSD values below 8%. Identification, confirmation and quantitation were carried out by gas chromatography/mass spectrometry (GC–MS) in selected ion monitoring mode and gas chromatography/tandem mass spectrometry (GC–MS/MS) using an ion trap operating in the multiple reaction monitoring (MRM) mode. The obtained limits of detection (LODs) were in the range 0.1–0.3 μg kg⁻¹, depending on the technique. The proposed methods were successfully applied to the analysis of suspected pepper samples.     

Residue levels of food-grade antioxidants in postharvest treated in-pod peanuts during five months of storage

In order to investigate residue levels of butylated hydroxyanisole (BHA), propyl paraben (PP) and butylated hydroxytoluene (BHT) during storage, eight-hundred kilograms of bulk peanuts were treated with the following antioxidant emulsions: BHA (1802 μg g⁻¹), BHA–PP (1802 μg g⁻¹ + 1802 μg g⁻¹) M1 and BHA–PP–BHT mixtures (1802 μg g⁻¹ + 901 μg g⁻¹ + 2204 μg g⁻¹) M2 and (1802 μg g⁻¹ + 1802 μg g⁻¹ + 2204 μg g⁻¹) M3. Residues were determined in peanut pod and seed tissues at 1-month intervals during the storage. While the reduction levels of BHA and PP in pods at the end of the storage period ranged from 66% to 76%, BHT levels were decreased extensively (86%). Twenty-four hours after peanuts were treated, antioxidant emulsions effectively seeped into the seeds and low levels of these chemicals were detected during the assay. Residues of PP in seeds were lower (62%) than the other antioxidants. Although the doses used were higher than those approved for food-grade antioxidants in stored peanuts, the residue levels in seeds (32.8–0.02 μg g⁻¹) did not exceed the maximum residue limits during the storage period.     

Determination of Ge(IV) in rice in a mercury-coated glassy carbon electrode in the presence of catechol

Electrochemical adsorptive cathodic stripping voltammetry determination of Ge(IV) using the catechol complex on a mercury-coated (MC) electrode was prepared using a glassy carbon electrode (GCE), the peak potential of which was −0.5 V vs. Ag/AgCl on MCGCE. The various parameters of the catechol concentration, its pH, and others were optimized. The linear working ranges were obtained in the concentration of 2–700 μg L⁻¹ Ge(IV). The relative standard deviation at the Ge(IV) concentration of 50 μg L⁻¹ was 1.37% (n = 15) using the optimum condition, and the detection limit was found to be 0.6 μg L⁻¹ (8.26 × 10⁻⁹ M) (S/N = 3), with an adsorption time of 180 s. The Ge(IV) response was highly linear. This developed method was applied to Ge(IV) to determine the presence of rice grains.