Hydroisomerization of Benzene-Containing Gasoline Fraction on Pt/B<Subscript>2</Subscript>O<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and Pt/WO<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Catalysts

The effect of the hydroisomerization conditions of the benzene-containing fraction of catalytic reforming gasoline on the yield and composition of products is studied on Pt/B₂O₃–Al₂O₃ and Pt/WO₃–Al₂O₃ catalysts. These catalysts allow benzene to be completely removed from the raw material. At the same time, the greatest yields of liquid products are obtained with minimal losses of the octane number at 2 MPa, a mass feedstock hourly space velocity (MFHSV) of 2 h^?1, and 325°C: 96.3 and 95.4 wt % on Pt/B₂O₃–Al₂O₃ and Pt/WO₃–Al₂O₃ catalysts, respectively. The activity of the catalysts is maintained for 100 h during their operation.     

Bimetallic Pd–Cu/ZnO–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and Pd–Cu/ZrO<Subscript>2</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts for methanol synthesis

Monometallic copper and bimetallic palladium-copper catalysts supported on ZnO–Al₂O₃ and ZrO₂–Al₂O₃ were prepared by conventional impregnation method and tested in methanol synthesis reaction under elevated pressure (3.5 MPa) in gradientless reactor at 220°C. The physicochemical properties of prepared catalytic systems were studied using BET, X-ray, TPR-H₂, TPD-NH₃ techniques. The promotion effect of palladium on catalytic activity and selectivity of copper supported catalyst in methanol synthesis reaction was proven. The highest activity of this system is explained by the Pd–Cu alloy formation.     

Photon interaction parameters for some ZnO–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript> glasses

Some photon interaction parameters such as mass attenuation coefficient, effective atomic number, half value layer, mean free path and electron density for 15ZnO–(17.5–x)Al₂O₃–xFe₂O₃–67.5P₂O₅ glass system (x = 0, 7.5, 12.5, 17.5) and 15ZnO–(25–x)Al₂O₃–xFe₂O₃–60P₂O₅ glass system (x = 0, 25) have been investigated in the photon energy range of 1 keV to 100 GeV. It has been observed that all the photon interaction parameters for the selected glass systems vary with the photon energy. Among the selected glass systems, the sample 15ZnO–25Fe₂O₃–60P₂O₅ glass system shows maximum values for mass attenuation coefficients, effective atomic numbers, electron densities and minimum values for mean free path and half value layer in the entire energy grid.     

Porous ceramics based on the ZrO<Subscript>2</Subscript>(Y<Subscript>2</Subscript>O<Subscript>3</Subscript>)–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> system for filtration membranes

The results of the studies of the process of fabricating ceramic filtration membranes in the system ZrO₂(Y₂O₃)–Al₂O₃ are presented. The phase compositions of the precursor powders and sintered ceramics have been investigated and their porous structures have been determined. Two stages of the implementation of the technology were demonstrated: fabrication of substrates with an open porosity ranging from 20 to 47% and pore sizes in the 100–300 nm range, as well as the deposition of nanocrystalline aluminum oxide layers on them. It has been established that the pore size distribution in the membrane layer of α-Al₂O₃ is unimodal (from 30 to 100 nm).     

Mechanical,Structural and Thermal Properties of Transparent Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–ZnO–TeO<Subscript>2</Subscript> Glass System

Oxide based optical glass materials has important potential material in many applications from fiber optic to sensor due to the high transparency and amourphous structures. The objective of this study is to synthesize the novel optical glass materials based on the bismuth and aluminum contents to be able to determine the physical, chemical and mechanical properties by considering the systematic experimental steps. In this study, Bi₂O₃–Al₂O₃ based tellurite optical glasses have been prepared by using conventional melt quenching method as a function of the both Bi₂O₃ and Al₂O₃ compositions. There is a strong interactions between the glass former and modifier ions that might effect on the structure and mechanical properties. During the experimental steps, thermal, structural and mechanical properties of the prepared glass materials have been determined considering the DTA/DSC, FT-IR spectroscopy, SEM and Vicker’s hardness techniques, respectively. Thermal parameters, like glass transition, T_g, onset, T_x, crystallization, T_p, and melting, T_m, temperatures were obtained by using DTA scan.     

Hydrodechlorination of CCl<Subscript>4</Subscript> on Pt–Au/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Catalysts

A series of Pt/Al₂O₃ catalysts were prepared by the impregnation method and were characterized by TEM, XRD, H₂ and CO chemisorptions, and investigated in the hydrodechlorination of tetrachloromethane. Three Pt-rich, Pt–Au/Al₂O₃ catalysts (Pt₁₀₀, Pt₉₅Au₅ and Pt₉₀Au₁₀) showed a similar metal particle size (~2.5–2.7 nm), so observed changes in the catalytic behavior are ascribed to alloying effect, especially because a considerable degree of Pt–Au mixing was achieved in the bimetallic samples. It appeared that by introducing very small amount of gold (10 at.%) to platinum, the catalytic activity is increased. It is argued that the occurrence of this moderate synergistic effect is associated with a decreased tendency of surface chloriding when platinum is alloyed with gold. Zbigniew Kowalczyk—deceased.     

Structural heterogeneity of SiO<Subscript>2</Subscript>–Na<Subscript>2</Subscript>O–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> glass

It is shown that the phase heterogeneity of SiO₂–Na₂O–Al₂O₃ glass has a liquation and crystallization nature, the balance between which is determined by the conditions of their synthesis. An increase in the aluminum oxide content decreases the number of liquation and crystallization sites, and also the linear sizes of the crystalline formations without eliminating the phase separation due to the liquation. The area of metastable immiscibility in the SiO₂–Na₂O–Al₂O₃ system, which is determined by scanning electron microscopy, is probably wider than the area detected by the optical methods.     

Novel Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> aerogel/porous zirconia composite with ultra-low thermal conductivity

Highly porous zirconia fibers networks with a quasi-layered microstructure were successfully fabricated using vacuum squeeze moulding. The effects of inorganic binder content on the microstructure, room-temperature thermal and mechanical properties of fibrous porous zirconia ceramics were systematically investigated. Al₂O₃–SiO₂ aerogel was impregnated into fibrous porous ceramics, and the microstructures, thermal and mechanical properties of Al₂O₃–SiO₂ aerogel/porous zirconia composites were also studied. Results show that the Al₂O₃–SiO₂ aerogel/porous zirconia composites exhibited higher compressive strength (i.e., 1.22 MPa in the z direction) and lower thermal conductivity [i.e., 0.049 W/(m/K)]. This method provides an efficient way to prepare high-temperature thermal insulation materials.     

Enhancement of the Activities of γ-Ga<Subscript>2</Subscript>O<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Catalysts for Methane-SCR of NO by Treatment with NH<Subscript>3</Subscript>

Abstract  

The precursor particles for γ-Ga₂O₃–Al₂O₃ solid solutions were prepared by the coprecipitation method from aqueous solutions of Ga(NO₃)₃ and Al(NO₃)₃ with (NH₄)₂CO₃ as a precipitant. The γ-Ga₂O₃–Al₂O₃ solid solutions were obtained by calcination of the precursor at 700 °C. In this paper, the performance of the catalysts treated with NH₃ was investigated for the selective catalytic reduction (SCR) of NO with methane as a reducing agent, and it was found that γ-Ga₂O₃–Al₂O₃ catalysts treated with NH₃ and subsequently annealed in air showed higher activities than the γ-Ga₂O₃–Al₂O₃ catalysts without NH₃ treatment. NH₃ treatment of the catalyst caused partial rearrangement of Ga³⁺ and Al³⁺ ions and increased the population of tetrahedral Ga³⁺ ions in the defective spinel structure.     

Exploring the Redox Behavior of La<Subscript>0.6</Subscript>Sr<Subscript>0.4</Subscript>Mn<Subscript>1−x</Subscript>Al<Subscript>x</Subscript>O<Subscript>3</Subscript> Perovskites for CO<Subscript>2</Subscript>-Splitting in Thermochemical Cycles

Mixed oxides with perovskite structure have been proposed as promising alternative for the solar fuel production via thermochemical redox cycles. For this work, the system La_0.6Sr_0.4Mn_1?xAl_xO₃ (x?=?0 to 0.8) was selected according to its high thermal stability and rapid oxidation kinetics, and the influence of the Al/Mn ratio on the redox properties was investigated. The characterization of the five oxides samples with different Al content confirmed the high redox capacity and the favorable behavior of these materials in consecutive cycles, as analyzed thermogravimetrically. The results show that following reduction at 1300?°C in inert atmosphere up to 0.32 mmol g^?1 of O₂ are released, while a 10-cycle reaction test confirms the feasibility of long term operation with these perovskites. It was observed that the reduction extent was enhanced with increasing the Al-content, but the oxidation degree is maximum for compositions near x?=?0.5, corresponding to an O₂ release of 0.318 mmol g^?1 (δ?=?0.132). After selecting the compositions with more promising redox properties, additional reactions were performed in a lab-scale fixed bed reactor with injection of CO₂ in the oxidation step at 900?°C in order to generate CO. In these tests, the most interesting results were obtained for the perovskite La_0.6Sr_0.4Mn_0.6Al_0.4O_3, with reduction extent of 0.266 mmol?g^?1, but the production of CO is in comparison significantly lower (0.114 mmol?g^?1). Further studies are required to determine the best operation conditions for thermochemical cycles using those materials.     

DRIFT,XPS and XAS Investigation of Au–Ni/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Synergetic Catalyst for Allylbenzene Isomerization

Au/Al₂O₃ and Ni/Al₂O₃ prepared by deposition-precipitation and impregnation methods, respectively, and Au–Ni/Al₂O₃ prepared by impregnation of the Au/Al₂O₃ system with nickel have been studied by physicochemical methods. The catalysts were tested in allylbenzene isomerization at 443 K. The isomerization on Au/Al₂O₃ proceeds with a rather low rate, while monometallic Ni/Al₂O₃ is inactive. Unlike monometallic catalysts, Au–Ni/Al₂O₃ demonstrates a strong synergetic effect: the isomerization rate on the bimetallic sample exceeds the sum of the rates over the individual metals by an order of magnitude. The catalysts structure was estimated by XPS, DRIFT, and XAS techniques. It was revealed that nickel in Au–Ni/Al₂O₃ and Ni/Al₂O₃ exist as Ni²⁺ cations with the coordination state close to that in the precursor, gold in Au/Al₂O₃ exist as Au⁰ nanoclusters, whereas the Au⁰ nanoclusters co-exist with Au³⁺ cations in the bimetallic Au–Ni/Al₂O₃ sample. Reasons of the synergetic catalytic effect for Au–Ni/Al₂O₃ are discussed in terms of the formation of new positively charged Au catalytic centers.     

Corrosion- and wear-resistant properties of Ni–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composite coatings containing various forms of alumina

This article describes the effect of the addition of different phases of alumina particles on the properties of electrodeposited Ni–Al₂O₃ composite coatings. The corrosion- and wear-resistant properties of Ni–Al₂O₃ composite coatings electrodeposited from a nickel sulfamate bath containing (i) alpha-alumina particles (Ni–Al₂O₃-1), (ii) gamma-alumina particles (Ni–Al₂O₃-2), and (iii) mixture of alpha, gamma, and delta alumina particles (Ni–Al₂O₃-3) have been studied. The potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) studies showed superior corrosion resistance of Ni–Al₂O₃-2 composite coatings compared with other two coatings. The SEM images and EDAX spectra also corroborated well with the observed corrosion results. The pin-on-disk wear studies showed improved wear resistance of Ni–Al₂O₃-1 composite coating containing alpha alumina compared with other two coatings. The transfer of material from the pin onto the disk was evident from the optical microscopy images of the wear tracks and Raman spectra of the wear track. This study shows that the addition of pure gamma-alumina particles enhances the corrosion resistance, and that pure alpha-alumina particles enhance the wear resistance of Ni composite coatings to a greater extent.     

Physicomechanical properties of refractory Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–Si<Subscript>3</Subscript>N<Subscript>4</Subscript>–C materials with ACPC

A study has been made on the effects of the amount of silicon nitride and graphite on the physicomechanical properties of Al₂O₃–Si₃N₄–C composites for lining purposes. Adding 2.5–5.0 wt.% silicon nitride and 0.5 wt.% reactive alumina improves the properties, raises their apparent density, and increases the mechanical strength, while reducing the open porosity. Optimized compositions have been determined for refractory materials of Al₂O₃–Si₃N₄–C composition, and it has been found that to attain the higher values of physicomechanical properties the amount of graphite should constitute 5–10 wt.%.     

Crystallization and Luminescence Properties of Sm<Superscript>3+</Superscript>-Doped SrO–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> Glass-Ceramics

Sm³⁺-doped SrO–Al₂O₃–SiO₂ glass-ceramics with excellent luminescence properties were prepared by batch melting and heat treatment. The crystallization behavior and luminescent properties of the glass-ceramics were investigated. The results indicate that the crystal phase in this system is monocelsian (SrAl₂Si₂O₈). Under the excitation with blue light (475 nm) the Sm³⁺-doped SrO–Al₂O₃–SiO₂ glass-ceramics emit green, orange and red lights centered at 565, 605, 650 and 715 nm, which can be assigned to the ⁴G_5/2 → ⁶H_J/2 (J = 5, 7, 9, 11) electron transitions in Sm³⁺ ions, respectively. With the increase of nucleation/crystallization temperature, the crystallite part rises from 66 to 79%. Besides, by increasing crystallization temperature or concentration of Sm³⁺, the samples emission located at 565, 605 and 650 nm is intensified significantly. We envision that, by fine controlling and combining of these three (green, orange and red) lights in an appropriate proportion, the Sm³⁺-doped glass-ceramics are promising luminescence materials for white light-emitting diodes devices.     

Magneto Optical Properties of FeB<Subscript>x</Subscript>Fe<Subscript>2−x</Subscript>O<Subscript>4</Subscript> Nanoparticles

In this study, FeB_xFe_2?xO₄ nanoparticles (NPs) were synthesized by the polyol method. The M–H hysteresis curves exhibit superparamagnetic characteristics that are both coercivity and remanent magnetization values are negligible. The particle size dependent Langevin function was applied to calculate the magnetic particle dimensions around 9 nm. The measured magnetic moments of NPs are in range of (1.52–2.2) µ_B and almost half or less with respect to 4 µ_B of bulk Fe ferrite. Magnetic anisotropy was specified as uniaxial and calculated effective anisotropy constants (K _eff ) are between 43.3 × 10⁴ and 19.4 × 10⁴ emu/g. The UV–Vis diffuse reflectance spectroscopy and Kubelka–Munk theory were used to determine the optical properties. The estimated optical band gap values (2.15–2.48 eV) of FeB_xFe_2?xO₄ NPs are bigger with respect to reported values (1.88–2.12 eV) for Fe₃O₄ NPs in the literature. The bigger E _g values are mainly attributed to B concentration and partly to quantum confinement effect.     

Crystallization of CaO–MgO–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> glass prepared by float process

CaO–MgO–Al₂O₃–SiO₂ (CMAS) glass was prepared by float process. The effects of TiO₂ and heat-treatment on properties and crystallization behaviors of float glasses were investigated by atomic force microscope, differential scanning calorimeter, X-ray diffraction, electron probe microanalyzer, field emission scanning electron microscope and viscosity test. The results showed that CMAS parent glasses produced by float process had a high surface flatness (Ra is less than 80.1 ± 0.1 nm) and low tin penetration (14 μm). When the concentration of TiO₂ increased from 3.51 to 5.01 wt %, the glass transition temperature was decreased, and the crystallization temperature was shifted from 913 to 887°C using differential scanning calorimeter. Field emission scanning electron microscope images showed that phase separation was discovered in CMAS parent glass (containing 3.51 wt % TiO₂) treated at 670°C. Diopside as a major crystalline phase was precipitated in CMAS glass-ceramics nucleated at 700°C for 30 min and followed by crystallization at 910°C for 30 min.     

Phase relationships in the Na<Subscript>2</Subscript>ZnP<Subscript>2</Subscript>O<Subscript>7</Subscript>–LiKZnP<Subscript>2</Subscript>O<Subscript>7</Subscript> system

The phase relationships in the Na₂ZnP₂O₇–LiKZnP₂O₇ system are studied. They are represented by a mixture of the starting components in the subsolidus region. The eutectic was found at a temperature of 640°C and composition of 0.5LiKZnP₂O₇. The phase formation of this system is compared with the previously studied NaKZnP₂O₇–LiKZnP₂O₇ system. It is shown that a structural factor affects the geometry of the state diagrams.