空气中微细电火花沉积的工艺规律研究

论述了一种新的电火花加工方法，它通过合理选择工艺条件在空气中将金属材料放电沉积在工件上。对电火花沉积加工的基本原理进行了分析，预测了实现条件，使用通用的电火花成形加工机床和常见的电极材料黄铜，在空气介质中，通过大量实验对微细电火花沉积进行了系统研究，得出各工艺参数的影响规律。在高速钢工件表面沉积出直径为0．19mm、高度为7.35mm的微小圆柱体。对沉积材料的测试表明，沉积材料致密，与基体结合紧密，成分取决于工具电极材料，同时基体硬度得到提高。     

空气中微细电火花沉积与去除可逆加工技术研究

论述了一种新的电火花加工方法。它使用通用的电火花成形加工机床,利用常见的电极材料,在空气介质中,通过脉冲放电在工件表面上沉积生长电极材料,再通过反转极性和适当的轨迹控制对所生成的沉积材料进行有选择的去除加工,进而实现材料的生长与去除可逆加工。通过对电火花加工理论的研究,预测和论证了实现这一新加工方法的可能性和实现条件。通过试验成功地将钢、铜和钨三种电极材料沉积到工件上,形成直径为 100~240 mm、高度为1 000~2 500 mm的微小圆柱体。并对沉积物进行了选择去除,实现了在同一设备上的可逆电火花加工。对沉积材料的致密性、硬度及其与工件的结合强度等进行了系统的分析,表明沉积物组织致密、坚硬,可以满足功能材料的要求。     

Micro Electrical Discharge Machining Deposition in Air for Fabrication of Micro Spiral Structures

Micro electrical discharge machining(EDM) deposition process is a new micro machining method for fabrication of metal micro structures. In this process, the high level of tool electrode wear is used to achieve the metal material deposition. Up to now, the studies of micro EDM deposition process focused mainly on the researches of deposition process, namely the effects of discharge parameters in deposition process on the deposition rate or deposition quality. The research of the formation of micro structures with different discharge energy density still lacks. With proper conditions and only by the z-axis feeding in vertical direction, a novel shape of micro spiral structure can be deposited, with 0.11 mm in wire diameter, 0.20 mm in outside diameter, and 3.78 mm in height. Then some new deposition strategies including angular deposition and against the gravity deposition were also successful. In order to find the forming mechanism of the spiral structures, the numerical simulation of the transient temperature distribution on the discharge point was conducted by using the finite-element method(FEM). The results show that there are two major factors lead to the forming of the spiral structures. One is the different material removal form of tool electrode according with the discharge energy density, the other is the influenced degree of the movement of the removed material particles in the discharge gap. The more the energy density in single discharge is, the smaller the mass of the removed material particles is, and the easier the movements of which will be changed to form an order tendency. The fine texture characteristics of the deposited micro spiral structures were analyzed by the energy spectrum analysis and the metaliographic analysis. It shows that the components of the deposited material are almost the same as those of the tool electrode. Moreover the deposited material has the brass metallic luster in the longitudinal profile and has compact bonding with the base material. This research is useful to understand the micro-process of micro EDM deposition better and helpful to increase the controllability of the new EDM method for fabrication of micro structures.     

Experimental Investigation on Electrical Discharge Drilling of Ti-6Al-4V Alloy

This article describes the experimental investigation related to creation of holes in aerospace titanium alloy workpiece using static electrode machining and electrical discharge drilling (EDD) process. Special attachment for holding and rotating the tool electrode was developed and installed on electrical discharge machining (EDM) machine by replacing the original conventional tool holder provided on die sinking EDM. The effect of input parameters such as gap current, pulse on-time, duty factor and RPM of tool electrode on output parameters for average hole circularity (C_a) and average surface roughness (R_a) have been studied. It is observed that the effect of rotating electrode machining has considerable influence on the output parameters over stationary electrode machining. The micro-graphs and photographs of few selected samples were taken by SEM and metallurgical microscope, which also commensurate with the findings of the study.     

Accretion of titanium carbide by electrical discharge machining with powder suspended in working fluid

A surface modification method by electrical discharge machining (EDM) with a green compact electrode has been studied to make thick TiC or WC layer. Titanium alloy powder or tungsten powder is supplied from the green compact electrode and adheres on a workpiece by the heat caused by discharge. To avoid the production process of the green compact electrode, a surface modification method by EDM with powder suspended in working fluid is proposed in this paper. After considering flow of working fluid in EDM process, the use of a thin electrode and a rotating disk electrode are expected to keep powder concentration high in the gap between a workpiece and an electrode and to accrete powder material on the workpiece. The accretion machining is tried under various electrical conditions. Titanium powder is suspended in working oil like kerosene. TiC layer grows a thickness of 150 μm with a hardness of 1600 Hv on carbon steel with an electrode of 1 mm in diameter. When a disk placed near a plate rotates in viscous fluid, the disk drags the fluid into the gap between the disk and the plate. Therefore, the powder concentration in the gap between a workpiece and a rotational disk electrode can be kept high. A wider area of the accretion can be obtained by using the rotational electrode with a gear shape.     

Micro electrical discharge machining using high electric resistance electrodes

In micro electrical discharge machining (EDM), because the material removal per single pulse discharge mainly determines the minimum machinable size of a micro EDM, decreasing the material removal per single pulse discharge is important. In this study, in order to decrease the material removal per single pulse discharge, high electric resistance materials such as single-crystal silicon are used for electrodes. Analytical results show that when the electrode resistance increases, the peak value of the discharge current decreases, whereas the pulse duration increases. In addition, the discharge energy decreases when increasing the resistance. Silicon is used as a tool electrode, and the effect of resistivity of the silicon tool electrode on the diameter of discharge craters generated on the stainless steel workpiece is examined. Experimental results reveal that with increasing silicon electrode resistivity, the diameter of discharge craters decreases. Because the diameter of discharge craters can be decreased to 0.5 μm, improved finished surfaces of R_z 0.03 μm are obtained.     

基于刀轨广义偏置的电火花摇动加工补偿方法

针对电火花加工中电极摇动产生加工误差的问题,结合电极自由曲面数控加工的基本原理,提出基于数控刀轨广义偏置的补偿方法。通过对电极自由曲面原始加工刀轨的广义偏置计算,可有效、统一地解决自由曲面电极典型摇动方式所引起的加工误差问题,同时对偏置计算后产生的刀轨自交问题进行讨论。针对实际生产加工对象和不同的电极摇动方式,进行补偿计算和生产加工验证。检测结果表明,该方法能够较大地提高加工精度,缩短生产周期。     

混粉电火花加工中极性效应的研究

为研究极性效应对混粉电火花加工的影响规律．采用钢对钢加工、铜对钢加工两种电极组合在添加硅粉的煤油工作液及普通煤油工作液中进行实验，并更换不同的极性，考察了两极材料的去除率和表面粗糙度，结果表明负极总能得到更高的材料去除率，而正极总能得到更低的表面粗糙度值。此现象可从两极表面能量密度差异的角度予以解释。     

A review on the use of dielectric fluids and their effects in electrical discharge machining characteristics

Electrical discharge machining (EDM) is one of the earliest non-traditional machining processes. EDM process is based on thermoelectric energy between the work piece and an electrode. In electrical discharge machining (EDM), a process utilizing the removal phenomenon of electrical discharge in dielectric, the working fluid plays an important role affecting the material removal rate and the properties of the machined surface. Choosing the right dielectric fluid is critical for successful operations. This paper presents a literature survey on the use of dielectric fluids and also their effects in electrical discharge machining characteristics.     

Employing severe plastic deformation to the processing of electrical discharge machining electrodes

The tool electrode has a significant role in electrical discharge machining (EDM) performance, as it affects machining efficiency, surface quality and the geometrical accuracy of the machined component. This study presents a new approach for developing a pure copper electrode using severe plastic deformation (SPD) to enhance the machining characteristics during EDM. Equal channel angular pressing (ECAP) is selected because it is the most successful SPD method of processing bulk materials. Finite element analysis, microstructural assessment as well as nanoindentation tests are carried out to determine the behavior of pure copper after one and two ECAP passes. The effectiveness of EDM when using ECAP-treated electrodes is evaluated by introducing new techniques of measuring the volumetric overcut (VOC) and corner sharpness. In addition, tool wear rate (TWR), material removal rate (MRR), electrode wear ratio, surface roughness, surface crack density and the critical crack zone are studied. The results emphasize that an electrode subjected to one pass of ECAP can enhance the workpiece accuracy by decreasing the VOC and increasing corner sharpness by 13 and 66%, respectively. It is also revealed that the nanohardness enhancement following ECAP leads to lower TWR and electrode wear ratio. An investigation of the surface characteristics indicates a thinner recast layer is achieved when using one ECAP pass-treated electrode, which leads to 26% lower surface crack density.     

差动往复式微型电火花加工装置的研究

针对电火花加工技术的特点及超声波电动机驱动技术的特性,研制了基于线性步进式超声波电动机的差动往复式微型电火花加工装置,分析了该装置的工作原理,提出了电极差动往复式移动的驱动控制方法,实现了电极的差动往复式进给.该装置的外形尺寸为45mm×20mm×40mm.试验结果表明,该装置适合小孔电火花加工.     

Monitoring of the electrical discharge machining process by abductive networks

The paper describes the use of abductive networks to monitor the electrical discharge machining (EDM) process. The voltage and current across the gap between the tool and workpiece are fed into the developed networks for the recognition of various pulse types in EDM in a winner-take-all fashion. Experimental results have shown that EDM pulses can be clearly classified even with different machining conditions. Hence, a reliable technique has been developed to monitor the EDM process.     

Novel methods for high-speed observation of material removal and molten pool movement in EDM

This paper proposes two new methods to observe discharge phenomena without interference from the plasma in electrical discharge machining. The first method uses a bandpass filter with a bandwidth of 800–820 nm and laser illumination with a wavelength of 800–820 nm. The second method also uses a bandpass filter with a bandwidth of 800–820 nm; however, in this method, the tungsten material is used not only as the tool electrode but also as the illumination source. First, the discharge process was observed using traditional methods to investigate the influence of the plasma on the observation of the discharge process. Then, the process of removing molten material from both the tool electrode and workpiece, as well as molten pool movement, was observed using the first method proposed in this paper. The material removed from the tool electrode was scattered upward along the end profile of the tool electrode, while the material removed from the workpiece was distributed along the horizontal direction. To explain these phenomena, the flow distribution in the gap was qualitatively analyzed using a fluid simulation. Finally, the discharge process was also observed using the second method proposed in this paper. A tungsten tool electrode can emit light with a wavelength of 800–820 nm, which shines on the observed region during the discharge process. The observation results verified the phenomenon of multiple explosions of the molten pool during the discharge process. Moreover, it was found that the material removed by the explosion of the molten pool was scattered in different directions and hardly influenced by the flow distribution in the gap.     

Feasibility study of micro-slit EDM machining using pure water

This study addresses micro-slit EDM machining feasibility using pure water as the dielectric fluid. Experimental results revealed that pure water could be used as a dielectric fluid and adopting negative polarity EDM machining could obtain high material removal rate (MRR), low electrode wear, small slit expansion, and little machined burr, compared to positive polarity machining. In comparing kerosene versus pure water, pure water was observed to cause low carbon adherence to the electrode surface. Also discharge energy does not decrease and the discharge processes are not interrupted. Therefore, MRR was higher, and related electrode wear ratio compared to kerosene use was lower. In a continual EDM with multi-slit machining, kerosene will cause carbon element adherence, creating an initially high MRR and electrode wear, with rapid decline. However, pure water will not cause carbon element adherence on the electrode surface, so MRR and electrode wear is always stable in this process.     

Surface modification using semi-sintered electrodes on electrical discharge machining

This study investigates how machining characteristics and surface modifications affect low-carbon steel (S15C) during electrical discharge machining (EDM) processes with semi-sintered electrodes. Among the machining characteristics determined, the material removal rate (MRR), surface deposit rate (SDR), and electrode wear rate (EWR) are included. Additionally, exactly how semi-sintered electrodes affect the surface modifications is also evaluated by electron probe microanalyzer (EPMA), micro hardness, and corrosion resistance tests. The experimental results confirmed that the composition of the semi-sintered electrodes is transferred onto the machined surface efficiently and effectively during the EDM process, and that the process is feasible and can easily form a modified layer on the machined surface.     

Influence of electrical discharge machining parameters on cutting parameters of carbon fiber-reinforced plastic

Today the use of high-strength carbon fiber-reinforced plastics (CFRP) composite as a material for many engineering applications is showing an increasing demand in the industry. These composites are replacing the traditional use of steel because they offer many advantages such as very light weight, high strength, and high stiffness associated with good corrosion-resistant properties. Unfortunately, there is little technological knowledge on the electrical discharge machining (EDM) process of high-strength composite materials, especially about the CFRP. In this work, a study has made into the possibility of using EDM process as a means of machining CFRP composite. Various cutting conditions such as peak current, pulse-on time, pulse-off time and open-circuit voltage were selected to perform electrical discharge machining. The effect of electrode rotation was also studied. Optimum cutting conditions and machine settings for EDM were chosen for machining CFRP composites.     

基于数控刀位轨迹的电火花成形加工中电极平动补偿和修正

在电火花成形加工(EDM)中,电极的平动产生了加工误差。针对EDM中电极平动的不同类型,提出并实现了基于数控刀位轨迹的电极平动补偿修正方法。该方法根据EDM的电极平动类型和平动量对用于电极加工的数控程序进行补偿处理,达到对电极平动进行修正的目的,从而减少电极平动所产生的加工误差。试验表明,该方法可以有效地提高EDM加工精度、保持加工质量的稳定性以及降低劳动程度和缩短生产周期。     

Numerical and experimental study on the effect of vibration of the tool in ultrasonic assisted EDM

In this paper the effect of ultrasonic vibration of the tool in the process of electrical discharge machining is investigated. The ultrasonic vibration of the tool has significant effect on the dynamic behaviour of the vapour bubble generated between the tool and the workpiece due to the electrical discharge. The computational simulation of the bubble behaviour is carried out by employing the boundary integral equation method. Results show that when the electrical discharge occurs in the closest position of the tool to the workpiece, the vapour bubble expands to the largest maximum volume of the bubble and the lifetime of the bubble is the longest. This in turn makes the pressure inside the bubble decrease rapidly to the lowest magnitude and causes melted material at the sparked point vaporize and leave the crater on the surface of the workpiece.     

Performance and surface alloying characteristics of Cu–Cr and Cu–Mo powder metal tool electrodes in electrical discharge machining

The main objective of this study is to investigate the effect of Cu–Cr and Cu–Mo powder metal (PM) tool electrodes on electrical discharge machining (EDM) performance outputs. The EDM performance measures used in the study are material removal rate (MRR), tool electrode wear rate (EWR), average workpiece surface roughness (R_a), machined workpiece surface hardness, abrasive wear resistance, corrosion resistance, and workpiece alloyed layer depth and composition. The EDM performance of Cu–Cr and Cu–Mo PM electrodes produced at three different mixing ratios (15, 25, and 35 wt% Cr or Mo), compacting pressures (P_c = 600, 700, and 800 MPa), and sintering temperatures (T_s = 800, 850, and 900 °C) are compared with those machined with electrolytic Cu and Cu PM electrodes when machining SAE 1040 steel workpiece. Analyses revealed that tool materials were deposited as a layer over the work surface yielding high surface hardness, strong abrasion, and corrosion resistance. Moreover, the mixing ratio, P_c, and T_s affect the MRR, EWR, and R_a values.     

基于局域波分解的电火花加工放电状态预测方法

针对微细电火花加工和深孔电火花加工过程中频繁出现放电信号严重畸变、放电状态不稳定甚至放电状态突变等实际加工情况,建立基于模糊逻辑的电火花加工放电状态逐级映射检测系统;在此基础上,将局域波分解理论引入电火花加工放电状态预测的研究,结合系统辨识理论和线性预测方法,建立基于局域波分解的电火花加工放电状态预测数学模型,提出基于局域波分解的电火花加工放电状态预测方法。试验证明,基于局域波分解的电火花加工放电状态预测方法的预测精度高、辨识数据短、运算速度快、实时性强,能够有效消除传统预测方法的滞后性,达到提高微细和深孔电火花加工效率、增强电火花加工预测控制系统稳定性的目的,确保加工质量和加工效率等工艺目标的良好实现。