Polypropylene/polypropylene‐grafted acrylic acid blends for multilayer films: Preparation and characterization

Polypropylene (PP) was functionalized with acrylic acid (AA) and styrene (st) as a comonomer by means of a radical‐initiated melt‐grafting reaction. FTIR, ESCA, and ¹H‐NMR spectroscopies were used to characterize the formation of polypropylene grafted with acrylic acid (PP‐g‐AA) and polypropylene grafted with acrylic acid and styrene (PP‐g‐AAst). The content of AA grafted onto PP was determined by using volumetric titration. Blends of PP with 0–100 wt % of PP‐g‐AA were prepared by melt mixing. The effect of the modified polymer content on the surfaces of cast films was characterized through FTIR–ATR and ESCA analysis as well as contact‐angle, wetting‐tension, and ink‐adhesion measurements. The influence of the content of AA on the melting and crystallization temperature of PP was investigated by DSC. The contact angles of water on cast‐film surfaces of PP/PP‐g‐AA blends decreases with increasing modified polymer content and decreasing PP‐g‐AA molecular weight. A notorious improvement on wetting tension was observed with increasing modified polymer content and decreasing PP‐g‐AA molecular weight. From FTIR–ATR and ESCA spectra of the blends, a calculation was made of the carbonyl index on the films' surfaces. It was found that the higher the carbonyl index, the lower the contact‐angle value for the polypropylene blends. An increase in crystallization temperature of PP was observed when AA monomers were grafted into PP and with increasing PP‐g‐AA content in the blend, probably caused by a nucleation effect of AA monomers that would improve the crystallization capability of PP. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1497–1505, 2001     

The effect of addition of poly(propylene‐g‐acrylic acid) on the morphology of poly(vinyl methylether) and isotactic polypropylene blend

The interfacial adhesion of blend of isotactic polypropylene/poly(vinyl methylether) (i‐PP/PVME) has been improved by the addition of poly(propylene‐g‐acrylic acid) (PP‐g‐AA) as a compatibilizing agent. The phase morphologies of the blends are investigated by optical microscopy (OM) and lateral force microscopy (LFM). The i‐PP/PVME (80/20) blend with no addition of PP‐g‐AA from extrusion process shows a coarse morphology with the dispersed domain size as large as several micrometers; After the addition of 2.5% PP‐g‐AA in the blends, the dispersed PVME domain size decreases greatly. The addition of 5% PP‐g‐AA results in a homogeneous morphology. The blending of PP‐g‐AA with PVME reduces the crystallization temperature of PP‐g‐AA, which is different from that of blending i‐PP with PVME. The increase of the interfacial adhesion is attributed to the specific intermolecular interaction between the acrylic acid group of PP‐g‐AA and the ether group of PVME. The specific interaction is studied by Fourier transform infrared spectroscopy. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4098–4103, 2006     

Crystallization and melting behavior of nano‐CaCO3/polypropylene composites modified by acrylic acid

Nano‐CaCO₃/polypropylene (PP) composites modified with polypropylene grafted with acrylic acid (PP‐g‐AA) or acrylic acid with and without dicumyl peroxide (DCP) were prepared by a twin‐screw extruder. The crystallization and melting behavior of PP in the composites were investigated by DSC. The experimental results showed that the crystallization temperature of PP in the composites increased with increasing nano‐CaCO₃ content. Addition of PP‐g‐AA further increased the crystallization temperatures of PP in the composites. It is suggested that PP‐g‐AA could improve the nucleation effect of nano‐CaCO₃. However, the improvement in the nucleation effect of nano‐CaCO₃ would be saturated when the PP‐g‐AA content of 5 phf (parts per hundred based on weight of filler) was used. The increase in the crystallization temperature of PP was observed by adding AA into the composites and the crystallization temperature of the composites increased with increasing AA content. It is suggested that the AA reacted with nano‐CaCO₃ and the formation of Ca(AA)₂ promoted the nucleation of PP. In the presence of DCP, the increment of the AA content had no significant influence on the crystallization temperature of PP in the composites. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2443–2453, 2004     

Toughening of polypropylene with styrene/ethylene‐butylene/styrene triblock copolymer: Effects of reactive and nonreactive compatibilization

The effects of the compatibilization on the toughening of polypropylene (PP) by melt blending with styrene/ethylene‐butylene/styrene triblock copolymer (SEBS) in a twin‐screw extruder were investigated. The compatibilizers used were an SEBS functionalized with maleic anhydride, a PP functionalized with acrylic acid, and a bifunctional compound, p‐phenylenediamine (PPD). The effects of the compatibilization were evaluated through the mechanical properties and by the determination of the phase morphology of the blends by scanning electron microscopy. Reactive compatibilized blends show up to a 30‐fold increase in impact strength compared to neat PP, which was likely to have been due to the reaction of the bifunctional compound (PPD) with the acid acrylic and maleic anhydride groups, which rendered both morphological and mechanical stability to these blends. The addition of the PPD to the blends significantly changed their phase morphologies, leading to larger dispersed particles' average diameters, probably due to the morphological stabilization at the initial processing steps during extrusion, with the occurrence of the chemical reactions. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1081–1094, 2003     

Novel multimonomer‐grafted polypropylene preparation and application in polypropylene/poly(vinyl chloride) blends

A novel grafted polymer was prepared in one step through free‐radical melt grafting in a single‐screw extruder. It was shown that the addition of styrene (St) to the melt‐grafting system as a comonomer could significantly enhance the grafting degree of methyl methacrylate (MMA) onto polypropylene (PP) and reduce the degradation of the PP matrix by means of Fourier transform infrared and melt flow rate testing, respectively. Then, the potential of using multimonomer‐grafted PP, which was designated PP‐g‐(St‐co‐MMA), as the compatibilizer in PP/poly(vinyl chloride) (PVC) blends was also examined. In comparison with PP/PVC blends, the average size of the dispersed phase was greatly reduced in grafted polypropylene (gPP)/PVC blends because of the addition of the PP‐g‐(St‐co‐MMA) graft copolymer. The tensile strength of the gPP/PVC blends increased significantly, and the impact strength was unchanged from that of the pure PP/PVC blends. The results of differential scanning calorimetry and scanning electron microscopy suggested that the compatibility of the PP/PVC blends was improved. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Compatibilization of PP/EPDM blends by grafting acrylic acid to polypropylene and epoxidizing the diene in EPDM

In this article, ethylene–propylene–diene‐rubber (EPDM) was epoxidized with an in situ formed performic acid to prepare epoxided EPDM (eEPDM). The eEPDM together with the introduction of PP‐g‐AA was used to compatibilize PP/EPDM blends in a Haake mixer. FTIR results showed that the EPDM had been epoxidized. The reaction between epoxy groups in the eEPDM and carboxylic acid groups in PP‐g‐AA had taken place, and PP‐g‐EPDM copolymers were formed in situ. Torque test results showed that the actual temperature and torque values for the compatibilized blends were higher than that of the uncompatibilized blends. Scanning electron microscopy (SEM) observation showed that the dispersed phase domain size of compatibilized blends and the uncompatibilized blends were 0.5 and 1.5 μm, respectively. The eEPDM together with the introduction of PP‐g‐AA could compatibilize PP/EPDM blends effectively. Notched Izod impact tests showed that the formation of PP‐g‐EPDM copolymer improved the impact strength and yielded a tougher PP blend. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3949–3954, 2006     

Cellulose/acrylic acid copolymer blends for films and coating applications

Enzymatically treated cellulose was dissolved in a NaOH/ZnO solvent system and mixed together with poly(ethylene‐co‐acrylic acid) (PE‐co‐AA) or poly(acrylamide‐co‐acrylic acid) (PAA‐co‐AA) polymers, in order to improve the properties of dissolved cellulose and to prepare homogeneous cellulose‐based blends for films and coatings. The solution stage properties of the blends were evaluated by rheological methods and the precipitated dry blends were characterized by dynamic mechanical analysis, differential scanning calorimetry, and scanning electron microscopy. Paperboard coating tests done at laboratory scale showed dissolved cellulose/acrylic acid copolymer‐based blends function well as coating materials. All of the tested blends showed a good resistance against grease in the coating trials, having grease resistance from 60 to 69 days despite a very thin (～2 µm) coating layer. In addition, cellulose/PE‐co‐AA coating showed improved water vapor and oxygen barrier properties when compared with neat dissolved cellulose‐coated paperboard. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40286.     

Nonisothermal crystallization kinetics of polypropylene/polypropylene‐g‐polystyrene/polystyrene blends

The nonisothermal crystallization kinetics of polypropylene (PP), PP/polystyrene (PS), and PP/PP‐g‐PS/PS blends were investigated with differential scanning calorimetry at different cooling rates. The Jeziorny modified Avrami equation, Ozawa method, and Mo method were used to describe the crystallization kinetics for all of the samples. The kinetics parameters, including the half‐time of crystallization, the peak crystallization temperature, the Avrami exponent, the kinetic crystallization rate constant, the crystallization activation energy, and the F(T) and a parameters were determined. All of the results clearly indicate that the PP‐g‐PS copolymer accelerated the crystallization rate of the PP component in the PP/PP‐g‐PS/PS blends. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Thermodynamically induced self‐assembled electrically conductive networks in carbon‐black‐filled ternary polymer blends

By calculating the surface tensions of the components, composites with innovative thermodynamically induced self‐assembled electrically conductive networks were designed, prepared and investigated. Carbon black (CB) was added into a ternary blend system comprised of poly(methyl methacrylate) (PMMA), ethylene–acrylic acid copolymer (EAA) and polypropylene (PP). Scanning electron microscopy images show that the PMMA/EAA/PP ternary blend forms a tri‐continuous phase structure like a sandwich, in which PMMA and PP form a co‐continuous phase while EAA spreads at the interface of the PMMA and PP phases as a sheath. The micrographs and resistivity–temperature characteristic curve results indicate that CB fillers are selectively located at the interface of the PMMA and PP phases, namely the EAA phase. The percolation threshold of PMMA/EAA‐CB/PP composites is 0.2 vol%, which is only one‐fifth of that of PP/CB composites. Copyright © 2011 Society of Chemical Industry     

Phase behavior of binary blends of PP/PP‐g‐AA: limitations of the conventional characterization techniques

In this study, miscibility/immiscibility issues of a binary blend consisting of polypropylene (PP) and acrylic acid grafted polypropylene (PP‐g‐AA) were investigated using rheometry, DSC, dynamic mechanical and thermal analysis (DMTA), AFM and time‐of‐flight secondary‐ion mass spectrometry (ToF‐SIMS). Phase separation analysis of such blend systems is a challenge and complex due to chemically similar components as well as the low value of acrylic acid groups in the graft copolymer. Thus, it is crucial to determine if the present blend shows some degree of miscibility or develops co‐continuous morphology between the components. The analysis of rheometrical, DSC and DMTA results indicated no sensitivity of these classical techniques for detecting the miscibility or immiscibility of such a system. However, AFM data effectively detected dispersed‐phase domains corresponding to the PP‐g‐AA rich phase. The results, for the first time, indicated that the start of phase separation occurs at a critical copolymer concentration between 2 and 5 wt%. Furthermore it was observed that, as the PP‐g‐AA content increases, the size and continuity of the dispersed phase increase and reach a highly continuous morphology. Additionally, ToF‐SIMS chemical imaging was carried out to aid in the interpretation of the AFM data. © 2016 Society of Chemical Industry     

Relationship between branch length and the compatibilizing effect of polypropylene‐g‐polystyrene graft copolymer on polypropylene/polystyrene blends

Three polypropylene‐g‐polystyrene (PP‐g‐PS) graft copolymers with the same branch density but different branch lengths were evaluated as compatibilizing agents for PP/PS blends. The morphological and rheological results revealed that the addition of PP‐g‐PS graft copolymers significantly reduced the PS particle size and enhanced the interfacial adhesion between PP and PS phases. Furthermore, it is verified that the branch length of PP‐g‐PS graft copolymer had opposite effects on its compatibilizing effect: on one hand, increasing the branch length could improve the compatibilizing effect of graft copolymer on PP/PS blends, demonstrated by the reduction of PS particle size and the enhancement of interfacial adhesion; on the other hand, increasing the branch length would increase the melt viscosity of PP‐g‐PS graft copolymer, which prevented it from migrating effectively to the interface of blend components. Additionally, the crystallization and melting behaviors of PP and PP/PS blends were compared. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40126.     

Real time assessment of the compatibilization of polypropylene/polyamide 6 blends during extrusion

The reactivity of maleic anhydride and acrylic acid polypropylene graft copolymers with amine groups and their effect in the compatibilization of polymer blends was analyzed in real time during the reactive processing of compatilized polypropylene/polyamide 6 (PP/PA6) blends. The presence of compatibilizers in the blend produces a block copolymer PP‐PA6, which stays in the blends interface, lowering the interfacial tension and reducing the PA6 particle size, affecting the light extinction phenomena. The in‐line optical detector is able to indirectly quantify the conversion of the compatibilization reaction of the blends. The signal intensity of the detector increases with the increase of the PA6 content due to the increase in the number of particles. Quantitative off‐line FTIR analyses of the compatibilized blends have shown that the amount of block copolymer formed when polypropylene grafted with acrylic acid (PP‐g‐AA) is used as compatibilizer increases with its content in the blend. There is a good correlation between the in‐line optical measurement and the off‐line amidic bond content formed. Non‐reacted compatibilizers are always present in the reactive blends whose content is proportional to its initial concentration. The PA6 particle size data obtained from scanning electron microscopy analysis showed good correlation with the in‐line measurements. POLYM. ENG. SCI., 2010. © 2009 Society of Plastics Engineers     

Compatibilization of polypropylene/nylon 6 blends with a polypropylene solid‐phase graft

The compatibilization of polypropylene (PP)/nylon 6 (PA6) blends with a new PP solid‐phase graft copolymer (gPP) was systematically studied. gPP improved the compatibility of PP/PA6 blends efficiently. Because of the reaction between the reactive groups of gPP and the NH₂ end groups of PA6, a PP‐g‐PA6 copolymer was formed as a compatibilizer in the vicinity of the interfaces during the melting extrusion of gPP and PA6. The tensile strength and impact strength of the compatibilized PP/PA6 blends obviously increased in comparison with those of the PP/PA6 mechanical blends, and the amount of gPP and the content of the third monomer during the preparation of gPP affected the mechanical properties of the compatibilized blends. Scanning electron microscopy and transmission electron microscopy indicated that the particle sizes of the dispersed phases of the compatibilized PP/PA6 blends became smaller and that the interfaces became more indistinct in comparison with the mechanical blends. The microcrystal size of PA6 and the crystallinity of the two components of the PP/PA6 blends decreased after compatibilization with gPP. The compatibilized PP/PA6 blends possessed higher pseudoplasticity, melt viscosity, and flow activation energy. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 420–427, 2004     

Study on the properties of polyethylene–octene elastomer/wood flour blends

In the present study, the properties of metallocene polyethylene–octene elastomer (POE) and wood flour (WF) blends were examined by Fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry (DSC), an Instron mechanical tester, and scanning electron microscopy (SEM). The results showed that the mechanical properties of POE were obviously lowered, due to the poor compatibility between the two phases, when it was blended with WFs. A fine dispersion and homogeneity of WF in the polymer matrix could be obtained when acrylic acid‐grafted POE (POE‐g‐AA) was used to replace POE for manufacture of the blends. This better dispersion is due to the formation of branched and crosslinked macromolecules since the POE‐g‐AA copolymer had carboxyl groups to react with the hydroxyls. This is reflected in the mechanical and thermal properties of the blends. In comparison with a pure POE/WF blend, the increase in tensile strength at break was remarkable for the POE‐g‐AA/WF blend. The POE‐g‐AA/WF blends are more easily processed than are the POE/WF blends, since the former had a lower melt viscosity than that of the latter. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1919–1924, 2003     

Morphological and mechanical properties of PP/ABS blends compatibilized with PP‐g‐acrylic acid

Polypropylene (PP) and acrylonitrile–butadiene–styrene (ABS) blends were prepared by a melt extrusion process. PP‐g‐acrylic acid was used as a compatibilizer. Blends with various compositions of PP, compatibilizer, and ABS were prepared and studied for morphological and mechanical properties. PP‐rich ternary blends showed good morphological and mechanical properties. The use of 5 wt % PP‐g‐acrylic acid as a compatibilizer resulted in a fine and homogeneous dispersion of the ABS phase in the PP phase. The experimental data of the tensile modulus showed good agreement in PP‐rich compositions with that generated from Kerner's model with perfect adhesion. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1731–1741, 2001     

Melt‐mixed polypropylene/acrylonitrile‐butadiene‐styrene blends with multiwall carbon nanotubes: Effect of compatibilizer and modifier on morphology and electrical conductivity

Cocontinuous blends of 45/55 polypropylene (PP)/acrylonitrile‐butadiene‐styrene (ABS) with multiwall carbon nanotubes (MWNT) were prepared by melt‐mixing in a conical twin‐screw microcompounder. PP‐grafted‐maleic anhydride (PP‐g‐MA) and styrene MA were used as compatibilizers for PP/ABS blends. Scanning electron microscopic observations showed phase segregation of PP‐g‐MA in the blends. State of dispersion of MWNT in the presence or absence of the compatibilizers was assessed through AC electrical conductivity measurements and crystallization studies of the blends. An improvement in AC electrical conductivity was observed in blends in presence of either styrene MA or dual compatibilizers. The lowest electrical percolation threshold was achieved at 0.1 wt % of MWNT using sodium salt of 6‐amino hexanoic acid‐modified MWNT. Significant increase in crystallization temperature of PP phase of blends with MWNT was observed in the presence of compatibilizers as compared to blends without compatibilizers. An attempt has been made to address the complex issues of phase segregation, compatibilization, and dispersion of MWNT in cocontinuous blends of PP/ABS. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Influence of a compatibilizer on the properties of polyethylene–octene elastomer/starch blends

The effect of a compatibilizer on the properties of corn starch‐reinforced metallocene polyethylene–octene elastomer (POE) blends was studied. The compatibility between POE and starch was improved markedly with an acrylic acid‐grafted POE (POE‐g‐AA) copolymer as a compatibilizer. Fourier transform infrared spectroscopy, X‐ray diffraction spectroscopy, differential scanning calorimetry, and scanning electron microscopy were used to examine the blends produced. The size of the starch phase increased with an increasing content of starch for noncompatibilized and compatibilized blends. The POE/starch blends compatibilized with the POE‐g‐AA copolymer lowered the size of the starch phase and had a fine dispersion and homogeneity of starch in the POE matrix. This better dispersion was due to the formation of branched and crosslinked macromolecules because the POE‐g‐AA copolymer had anhydride groups to react with the hydroxyls. This was reflected in the mechanical properties of the blends, especially the tensile strength at break. In a comparison with pure POE, the decrease in the tensile strength was slight for compatibilized blends containing up to 40 wt % starch. The POE‐g‐AA copolymer was an effective compatibilizer because only a small amount was required to improve the mechanical properties of POE/starch blends. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1792–1798, 2002     

Synthesis of polypropylene graft copolymers from a hydroxyl‐groups‐containing polypropylene precursor via atom‐transfer radical polymerization

Isotactic polypropylene graft copolymers, isotactic[polypropylene‐graft‐poly(methyl methacrylate)] (i‐PP‐g‐PMMA) and isotactic[polypropylene‐graft‐polystyrene] (i‐PP‐g‐PS), were prepared by atom‐transfer radical polymerization (ATRP) using a 2‐bromopropionic ester macro‐initiator from functional polypropylene‐containing hydroxyl groups. This kind of functionalized propylene can be obtained by copolymerization of propylene and borane monomer using isospecific MgCl₂‐supported TiCl₄ as catalyst. Both the graft density and the molecular weights of i‐PP‐based graft copolymers were controlled by changing the hydroxyl group contents of functionalized polypropylene and the amount of monomer used in the grafting reaction. The effect of i‐PP‐g‐PS graft copolymer on PP‐PS blends and that of i‐PP‐g‐PMMA graft copolymer on PP‐PMMA blends were studied by scanning electron microscopy. Copyright © 2006 Society of Chemical Industry     

Blends of i‐PP and SBS. II. Influence of in situ compatibilization on the mechanical properties

This article concerns the in situ compatibilization of immiscible isotatic polypropylene/styrene–butadiene–styrene triblock copolymer blends (i‐PP/SBS) by use of a reactive mixture. For this purpose, maleated PP (PP–MAH) and SBS (SBS–MAH) were used as functionalized polymers and 4,4′‐diaminediphenylmethane was used as a coupling agent between maleated polymers, resulting in a graft copolymer. Binary blends of i‐PP/SBS, nonreactive ternary blends of i‐PP/PP–MAH/SBS, and reactive ternary blends of i‐PP/PP–MAH/SBS–MAH with varying diamine/anhydride molar ratios were prepared. The mechanical properties of the blends were determined by tensile and impact‐resistance tests. The optimum improvement in the mechanical properties was found when the diamine/anhydride molar ratio in the ternary reactive blends was 0.5/1. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 516–522, 2003     

Ammonia adsorption behavior of polypropylene nonwoven fabric grafted with acrylic acid

An attempt was made to synthesize an adsorbent by the photoinduced grafting of acrylic acid (AA) onto polypropylene nonwoven fabrics using benzophenone (BP) as a photosensitizer in a CH₃OH/H₂O medium. As the BP concentration was increased, the graft yield was increased up to a specific value and then decreased, and the effect of AA concentration showed the same tendency. It was also found that the graft yield increased with the reaction time and temperature. The amounts of ammonia adsorbed onto polypropylene nonwoven fabrics grafted with AA (PP‐g‐AA) were dependent on the graft yield, adsorption time, and ammonia gas pressure. The adsorption capacity of PP‐g‐AA was 5.86 mmol/g at the graft yield of 116.6%, which was much higher than that of active carbon or silica gel. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 295–301, 2002; DOI 10.1002/app.10328