氧化锌纳米棒阵列对芳纶的改性

利用湿化学方法在芳纶Ⅲ表面预制氧化锌(ZnO)晶种层,再在晶种膜的基础上制备出了垂直生长的ZnO纳米棒阵列。采用X射线衍射(XRD)、场发射扫描电镜(FE-SEM)和微脱黏试验对纤维表面的组成、形貌及复合材料的界面黏结性能进行了研究。结果表明:纤维表面生长的ZnO纳米棒阵列属于六方纤锌矿晶相,纳米棒垂直生长在纤维表面,增大了与基体的接触面积,能够使纤维更好地与环氧树脂基体间发生界面结合,进而有效改善芳纶Ⅲ-环氧复合材料的界面黏接强度。     

芳纶纤维/AFR树脂复合材料界面粘结性能的研究

为了改善芳纶纤维复合材料的界面粘结性能,合成了一种新型树脂(AFR)作为基体,以未经任何表面处理的芳纶纤维作增强材料,制备了芳纶纤维/AFR复合材料。采用测定表面能、接触角、层间剪切强度、横向拉伸性能和扫描电镜观察形貌等方法,从宏观和微观等方面研究了芳纶纤维/AFR复合材料的界面粘结性能。结果表明,AFR树脂与芳纶纤维有相近的表面能,AFR树脂溶液与芳纶纤维的接触角为42.8°,而环氧树脂(EP)与芳纶纤维的接触角为68°,说明AFR树脂对芳纶纤维的润湿性优于EP树脂;芳纶/AFR复合材料的层间剪切强度、横向拉伸强度和纵向拉伸强度分别为74.64MPa、25.34MPa和2256MPa,比芳纶/EP复合材料的相应强度分别提高了28.7%、32.5%和13.4%,其复合材料破坏面的形貌也说明芳纶纤维与AFR树脂之间的界面粘结性能较好。     

环氧树脂/多巴胺增强芳纶纤维界面性能

由于芳纶纤维表面光滑且呈现化学惰性,与环氧树脂等基体材料结合后界面性能较差。为此,采用多巴胺在不同时间下对改进型芳纶Ⅲ纤维表面进行改性处理,并研究了对环氧树脂/多巴胺改性芳纶纤维界面性能的影响。对扫描电子显微镜对纤维改性前后表面形貌进行表征,发现纤维改性后表面粗糙度提高,利于与环氧树脂间界面结合。利用傅里叶变换红外光谱、X射线光电子能谱对纤维改性前后基团和表面元素含量进行表征,改性后纤维表面活性基团增加,极性增强。通过热重分析表明聚多巴胺成功吸附在纤维表面。测量纤维表面接触角,改性后的接触角更小,有利于环氧树脂润湿纤维。采用横向丝束复合材料的拉伸强度表征环氧树脂/芳纶纤维的界面性能。最终确定了多巴胺浓度为2 g/L,在多巴胺溶液中处理4 h为最佳条件,在该条件拉伸强度比为改性前提高了28.06%,拉伸弹性模量提高了14.68%。     

纳米SiO2改性EP对基体力学性能和芳纶纤维/EP复合材料界面性能的影响

研究了纳米SiO2对环氧树脂(EP)基体力学性能的影响,并进一步采用对位芳纶纤维(F-12)增强环氧树脂,制备了NOL环复合材料,通过复合材料层间剪切性能测试考核了F-12与环氧树脂之间的界面粘接性能.结果表明:环氧树脂中添加适量的纳米SiO2能够有效提高环氧树脂浇注体的拉伸强度、拉伸弹性模量、冲击强度.纳米SiO2的加入,可以有效改善F-12与环氧树脂基体之间的界面粘接性能,降低复合材料的空隙率,F-12/纳米SiO2(6%)-EP复合材料的层间剪切强度(ILSS)提高约60.3%.     

纳米氧化锌改性环氧树脂的性能研究

选用纳米氧化锌(ZnO)改性环氧树脂性能,首先用硅烷偶联剂KH-550对纳米ZnO进行表面修饰,改善了环氧树脂和纳米ZnO的界面相容性,然后用红外光谱(FTIR)表征了表面修饰纳米ZnO的结构。用差示扫描量热法(DSC)、热失重分析法(TG)和力学性能测试研究了纳米ZnO表面修饰前后和含量对环氧树脂的玻璃化温度(T)、热稳定性和力学性能的影响,用扫描g电子显微镜(SEM)观察了加入纳米ZnO环氧固化物的脆断断面的形貌。结果表明,加入0.8质量份(100质量份环氧树脂中的加入量,下同)表面修饰的纳米ZnO后环氧树脂的拉伸强度、弯曲强度和冲击韧度分别提高了26%、20%和63%,T_g提高了20℃,最快分解温度提前了20℃。     

芳纶纤维增强树脂基复合材料的界面粘结性能研究

为了改善芳纶纤维增强树脂基复合材料的界面粘结性能,从树脂基体入手,依据相似相容原理和芳纶的结构特点,合成出新型热固性树脂(AFR–T)用作芳纶复合材料的基体,以未经表面处理的芳纶作增强材料,采用热压成型法制备了AFR–T/芳纶纤维复合材料,并通过测定溶度参数、接触角、线膨胀系数、层间剪切强度(ILSS)和横向拉伸强度等方法研究了复合材料的界面粘结性能。结果表明,AFR–T树脂浇注体与芳纶的溶度参数相近,AFR–T树脂溶液在芳纶纸表面的接触角为36.9°,小于环氧树脂(EP)溶液与芳纶纸的接触角(53.2°),说明AFR–T树脂对芳纶的浸润性优于EP;AFR–T/芳纶纤维复合材料的ILSS和横向拉伸强度为73.0 MPa和25.3 MPa,分别比EP/芳纶纤维复合材料提高了25.9%和32.5%,这表明AFR–T树脂与芳纶纤维之间的浸润性和界面粘结性能较好。     

芳纶纤维的热氧化处理及对环氧树脂界面黏结的影响

采用红外光谱(FTIR)、热重(TG)、差示扫描量热(DSC)对芳纶纤维在N_2和空气气氛下的热行为进行了研究,并以透射电镜(TEM)、界面剪切强度(IFSS)研究了芳纶纤维的空气热氧化处理及对其环氧树脂界面黏结的影响。结果表明:芳纶纤维在空气条件下,150～200℃温度范围内,仅仅是纤维表层上浆剂的挥发。250℃以上会出现分子链的氧化,同时纤维表层分子链能够重排使得氢键增强。高温过程中芳纶纤维的分子链苯环C—H被氧化成—C—OH、—COOH,从而使纤维表面极性增强。极性的结构有利于与环氧树脂的界面反应,使纤维与环氧树脂间形成40～50 nm的界面层。热处理后,芳纶纤维与环氧树脂微滴间界面剪切强度值增至18.05 MPa,与原丝相比增加了11.9%。同时,高温氧化后的芳纶纤维/环氧树脂界面黏合增强,复合材料的层间剪切强度为76.2 MPa,与原丝相比提高16.16%。     

芳纶纤维/环氧树脂预浸料界面相容性的方法探究

预浸料要求树脂基体和增强纤维具有良好的匹配性,为了提高芳纶纤维/环氧树脂预浸料的界面相容性,本文从芳纶纤维表面改性及增韧技术两个方面进行综述,讨论了芳纶纤维物理改性和化学改性方法的优缺点,分析了界面增韧及环氧树脂基体的不同增韧途径,重点介绍了聚氨酯/环氧树脂互穿网络体系.认为芳纶纤维的偶联剂表面处理和聚氨酯增韧环氧树脂相结合,是提高芳纶纤维/环氧树脂预浸料层间剪切强度的的可行途径.     

纳米SiO_2改性环氧树脂胶粘剂的研究

选择纳米 SiO_2 作为增强材料改性环氧树脂基体, 以物理分散法将纳米 SiO_2 分散在环氧树脂中。通过力学性能测试和热稳定性能测试, 研究了不同含量的纳米 SiO_2 对改性环氧树脂胶粘剂的热性能、拉伸性能和冲击性能的影响; 通过 NOL环测试和扫描电子显微镜(SEM) 分析, 研究了不同含量的纳米 SiO_2 对国产芳纶纤维/改性环氧复合材料的界面性能和层间剪切强度的影响。实验结果表明, 基体树脂中当 w( 纳米SiO_2)=3%时, 改性环氧树脂胶粘剂的拉伸强度和冲击强度分别提高了 28.8%和 22.6%, 复合材料的层间剪切强度(ILSS) 达到最大值, 比未改性胶粘剂提高约 56.8%。     

低温等离子体处理对芳纶/环氧界面性能的影响

在采用低温等离子体对芳纶纤维进行表面处理后，用扫描电镜观察处理前后的纤维表面，测试了纤维的拉伸性能，并用单纤维抽拔法对芳纶纤维／环氧树脂的界面性能做了定量的表征。实验结果表明：经低温等离子体处理后，芳纶纤维表面变得粗糙，拉伸强度随处理时间延长而下降，纤维初始模量和断裂伸长率略有下降，而芳纶／环氧界面的粘结强度有所提高。     

左旋多巴胺处理对芳纶表面结构与性能的影响

利用L-3,4-二羟基苯丙氨酸(L-DOPA)的氧化自聚合,在杂环芳纶表面修饰聚L-3,4-二羟基苯丙氨酸(PDOPA)活性涂层来提高芳纶的表面活性及耐紫外辐照性能。结果表明:改性后芳纶表面粗糙度显著提高,同时,PDOPA涂层上大量的羧基、羟基等活性单元均有利于增强与环氧树脂的机械锁合力,改性后芳纶/环氧树脂复合材料的界面剪切强度提高了32.0%。此外,上述改性过程对杂环芳纶本身力学性能影响较小,纤维的拉伸强度保持率可以达到100%,基本实现了无损改性。同时,由于PDOPA的保护作用,改性后芳纶的耐紫外辐射性能显著提高;经过168 h紫外线辐照处理后,其拉伸强度保持率可达到92.5%,显著提升了杂环芳纶的耐紫外线辐照特性。     

Effect of ultrasound on wettability between aramid fibers and epoxy resin

Good wetting of reinforced fiber by resin was a main factor in the improvement of the interface adhesion of their composites. Ultrasound with a frequency of 20 kHz was used to improve the wettability between aramid fibers and epoxy resin during the winding process of the composites. The effects of ultrasound on the viscosity and surface tension of epoxy resin and on the surface characteristics of aramid fibers were investigated. The wettability of aramid fibers and treated epoxy resin under different conditions and of aramid fibers and epoxy resin under ultrasonic online treatment were compared. The results indicated that the main action of ultrasound was to force epoxy resin to impregnate aramid fibers, in addition to the influence of ultrasound on the properties of epoxy resin and aramid fibers. The results of microdebond testing showed that the interfacial shear strength (IFSS) of aramid/epoxy composites could be 26% higher than that of untreated composites because of the improved wettability between aramid fibers and epoxy resin subjected to ultrasonic online treatment. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Surface ammonification of the mutual‐irradiated aramid fibers in 1,4‐dichlorobutane for improving interfacial properties with epoxy resin

The mutual irradiated aramid fibers in 1,4‐dichlorobutane was ammoniated by ammonia/alcohol solution, in an attempt to improve the interfacial properties between aramid fibers and epoxy matrix. Scanning electron microscopy (SEM), X‐ray photoelectron spectroscopy (XPS), dynamic contact angle analysis (DCA), interfacial shear strength (IFSS), and single fiber tensile testing were carried out to investigate the functionalization process of aramid fibers and the interfacial properties of the composites. Experimental results showed that the fiber surface elements content changed obviously as well as the roughness through the radiation and chemical reaction. The surface energy and IFSS of aramid fibers increased distinctly after the ammonification, respectively. The amino groups generated by ammonification enhanced the interfacial adhesion of composites effectively by participating in the epoxy resin curing. Moreover, benefited by the appropriate radiation, the tensile strength of aramid fibers was not affected at all. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44924.     

低温氨气等离子体对芳纶表面的改性

采用氨气等离子体对芳纶表面进行改性,用X-射线光电子能谱、场发射扫描电子显微镜、力学性能测试等手段对改性前后纤维表面的元素组成、形貌及其拉伸强度进行表征,并进一步通过微脱黏方法分析了等离子体处理条件对芳纶/环氧树脂复合材料界面黏结强度的影响。结果表明:芳纶经表面改性后,其表面极性官能团、表面粗糙度均有所增加,同时与环氧树脂基体的界面黏结强度明显增加。     

RETRACTED ARTICLE: Surface modification of aramid fibers with novel chemical approach

Friedel–Crafts Reaction as a simple and convenient approach to the surface modification of aramid fiber was introduced in this paper. Epoxy chloropropane was chosen as the treatment reagent to modify aramid fibers surface via Graft reaction. After the modification, the interfacial properties of aramid/epoxy composites were investigated by the single fiber pull-out test (SFP), and the mechanical properties of aramid fibers were investigated by the tensile strength test. The results showed that the interfacial shear strength (IFSS) value of aramid/epoxy composites was enhanced by about 50%, and the tensile strength of aramid fibers had no obvious damage. The crystalline state of aramid fibers was determined by X-ray diffraction instrument (XRD), and the results showed that there were not any distinct crystal type varieties. The surface elements of aramid fibers were determined by X-ray photoelectron spectroscopy (XPS), the analysis of which showed that the oxygen/carbon ratio of aramid fiber surface increased obviously. The possible changes of the chemical structure of aramid fibers were investigated via Fourier transform infrared spectrum (FTIR), and the analysis of which showed that the epoxy functional groups were grafted into the molecule structure of aramid fibers. The surface morphology of aramid fibers was analyzed by Scanning electron microscope (SEM), and the SEM results showed that the physical structure of aramid fibers was not etched or damaged obviously. The surface energy of aramid fibers was investigated via the dynamic capillary method, and the results showed that the surface energy was enhanced by 31.5%, and then the wettability degree of aramid fiber surface was enhanced obviously too. All of the results indicated that this novel chemical modification approach not only can improve the interfacial bonding strength of aramid/epoxy composites remarkably, but also have no negative influence on the intrinsic tensile strength of aramid fibers.     

芳纶纤维等离子体接枝改性处理研究

采用等离子体接枝对芳纶纤维表面进行改性处理,采用XPS、浸润性、界面剪切强度对等离子体接枝处理前后的表面组成、复合材料界面粘接性能等进行了研究,结果表明:等离子体接枝处理可以有效地提高芳纶纤维表面的极性官能团,增加与基体树脂-环氧树脂的浸润性,进而提高芳纶/环氧复合材料的界面粘接强度.     

Interfacial studies on the surface modified aramid fiber reinforced epoxy composites

In this work, solutions of rare earth modifier (RES) and epoxy chloropropane (ECP) grafting modification method were used for the surface treatment of aramid fiber. The effect of chemical treatment on aramid fiber has been studied in a composite system. The surface characteristics of aramid fibers were characterized by Fourier transform infrared spectroscopy (FTIR). The interfacial properties of aramid/epoxy composites were investigated by means of the single fiber pull‐out tests. The mechanical properties of the aramid/epoxy composites were studied by interlaminar shear strength (ILSS). As a result, it was found that RES surface treatment is superior to ECP grafting treatment in promoting the interfacial adhesion between aramid fiber and epoxy matrix, resulting in the improved mechanical properties of the composites. Meanwhile, the tensile strengths of single fibers were almost not affected by RES treatment. This was probably due to the presence of reactive functional groups on the aramid fiber surface, leading to an increment of interfacial binding force between fibers and matrix in a composite system. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:4165–4170, 2006     

Ultrasonic modification of aramid fiber–epoxy interface

An ultrasonic irradiation technique is used during the process of fabricating aramid fiber–epoxy resin reinforced composites to improve the interfacial adhesion performance. Under the ultrasonic treatment, the change of the resin viscosity is studied. The results of a microbond test show obvious improvement in the interfacial shear strength after ultrasonic treatment. The mechanical properties of the composites, such as the interlaminar shear strength and tensile strength, are measured. Combined with the SEM results, these show it is the mechanical properties that are improved and the fracture modes are varied from the interface between the fibers and resin to the fibrillation of fibers and resin. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2764–2768, 2001