Synthesis and characterization of isocyanic acid,m‐phenylenediiso‐propylidene based poly(urethane‐urea) dispersions containing different amount of 2,2‐Bis(hydroxyl methyl)propionic acid

Isocyanic acid, m‐phenylenediiso‐propylidene (m‐TMXDI)‐based anionic poly(urethane‐urea) dispersions were prepared by the prepolymer mixing process. The equivalent ratio of NCO/OH was kept constant at 1.8, while 2,2‐bis(hydroxyl methyl) propionic acid (DMPA) used was varied from 3 to 10 wt %. The colloidal stability of poly(urethane‐urea) dispersions arose entirely from the presence of ionized carboxylic acid groups. The chemical structure of poly(urethane‐urea) dispersions with various amount of DMPA were identified by FTIR and ¹³C NMR analysis. The test results showed that the hydrophilicity of poly(urethane‐urea) dispersions were increased with increase in DMPA content. The degree of chain extension was much lower than the values predicted theoretically due to the side reaction of a small amount of hydrophilic isocyanate‐terminated prepolymer with water. The average particle size of poly(urethane‐urea) dispersions were decreased with an increase in DMPA content, and this lead to an increase in viscosity. Also, the thermal degradation behavior were measured and was shown that the initial degradation temperature shifted to lower temperature with an increase in DMPA content. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5737–5746, 2006     

Hg(II) removal with polyacrylamide grafted crosslinked poly(vinyl chloride) beads via surface‐initiated controlled/“living” radical polymerization

Polyacrylamide grafted crosslinked poly (vinyl chloride) beads (PAM‐PVC) were prepared by the surface‐initiated controlled/“living” radical polymerization (SI‐CLRP) methodology from the crosslinked poly(vinyl chloride) beads with surface modification with diethyldithiocarbamyl groups under UV irradiation. The macroiniferter, diethyldithiocarbamyl crosslinked poly(vinyl chloride) beads (DEDTC‐PVC) were prepared by the reaction of the surface C? Cl groups with sodium N,N‐diethyl dithiocarbamate. The “grafting from” polymerization exhibited some “living” polymerization characteristics and the percentage of grafting (PG%) increased linearly with polymerizing time and achieved 47.6% after 6 h UV irradiation. The beaded polymer with polyacrylamide surface was also characterized with Fourier transform infrared (FTIR) and scanning electron microscope (SEM). Its adsorption property for Hg(II) ion was also investigated preliminarily. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:3385–3390, 2006     

Synthesis and characterization of new functional poly(urethane‐imide) crosslinked networks

To synthesize new functional poly(urethane‐imide) crosslinked networks, soluble polyimide from 2,2′‐bis(3,4‐dicarboxyphenyl) hexafluoropropane dianhydride, 4,4′‐oxydianiline, and maleic anhydride and polyurethane prepolymer from polycaprolactone diol, tolylene 2,4‐diisocyanate and hydroxyl ethyl acrylate were prepared. Poly(urethane‐imide) thin films were finally prepared by the reaction between maleimide end‐capped soluble polyimide (PI) and acrylate end‐capped polyurethane (PU). The effect of polyurethane content on dielectric constant, residual stress, morphology, thermal property, and mechanical property was studied by FTIR, prism coupler, Thin Film Stress Analyzer (TFSA), XRD, TGA, DMTA, and Nano‐indentation. Dielectric constant of poly(urethane‐imide) thin films (2.39–2.45) was lower than that of pure polyimide (2.46). Especially, poly(urethane‐imide) thin films with 50% of PU showed lower dielectric constant than other poly(urethane‐imide) thin films did. Lower residual stress and slope in cooling curve were achieved in higher PU content. Compared to typical polyurethane, poly(urethane‐imide) thin films exhibited better thermal stability due to the presence of the imide groups. The glass transition temperature, modulus, and hardness decreased with increase in the flexible PU content even though elongation and thermal expansion coefficient increased. Finally, poly(urethane‐imide) thin films with low residual stress and dielectric constant, which are strongly affected by the morphological structure, chain mobility, and modulus, can be suggested to apply for electronic devices by variation of PU. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 113–123, 2006     

New thermoplastic segmented polyurethanes with hard segments derived from 4,4′‐diphenylmethane diisocyanate and methylenebis(1,4‐phenylenemethylenethio)dialcanols

New thermoplastic poly(ether–urethane)s and poly(carbonate–urethane)s were synthesized by a one‐step melt polymerization from poly(oxytetramethylene) diol (PTMO) and poly(hexane‐1,6‐diyl carbonate) diol (PHCD) as soft segments, 4,4′‐diphenylmethane diisocyanate, and 2,2′‐[methylenebis(1,4‐phenylenemethylenethio)]diethanol, 3,3′‐[methylenebis(1,4‐phenylenemethylenethio)]dipropan‐1‐ol or 6,6′‐[methylenebis(1,4‐phenylenemethylenethio)]dihexan‐1‐ol as unconventional chain extenders. The effects of the kind and amount of the polymer diol and chain extender used on the structure and properties of the polymers were studied. The polymers were examined by Fourier transform infrared (FTIR) spectroscopy, X‐ray diffraction analysis, atomic force microscopy, differential scanning calorimetry, thermogravimetric analysis (TGA), TGA coupled with FTIR spectroscopy, and Shore hardness and tensile testing. The obtained high‐molecular‐weight polymers showed elastomeric or plastic properties. Generally, the PTMO‐based polymers exhibited significantly lower glass‐transition temperatures (up to ?48.1 vs ?1.4°C), a higher degree of microphase separation, and ordering in hard‐segment domains in comparison with the corresponding PHCD‐based ones. Moreover, it was observed that the polymers with the PTMO soft segments showed poorer tensile strengths (up to 36.5 vs 59.6 MPa) but higher elongations at break. All of the polymers exhibited a relatively good thermal stability. Their temperatures of 1% mass loss were in the range 270–320°C. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Kinetic study of the urethane and urea reactions of isophorone diisocyanate

Kinetic studies of the catalyzed urethane reactions between isophorone diisocyanate (IPDI) and alcohols and of the urea reactions between an isocyanate‐terminated prepolymer [IPDI–PPG2000–IPDI, where PPG2000 is poly(propylene glycol) with a number‐average molecular weight of 2000 g/mol] and water in the bulk state were performed with Fourier transform infrared (FTIR) spectroscopy. Dibutyltin dilaurate was used as the catalyst for the urethane reaction, and various tertiary amines were used as catalysts for the urea reactions. The reactions were followed through the monitoring of the change in the intensity of the absorbance band for NCO stretching at 2270 cm^?1 in the FTIR spectra; the activation parameters were determined through the evaluation of the kinetic data obtained at various temperatures (within the range of 30–60°C). The kinetic data indicated that the catalyzed isocyanate/alcohol and isocyanate/water reactions both followed second‐order kinetics during their initial stages but later followed third‐order kinetics resulting from the autocatalytic effects of hydrogen bonding between the hydroxyl groups and the newly formed urethane and urea groups. Furthermore, activation energies of 64.88 and about 80 kJ/mol for the isocyanate/alcohol and isocyanate/water reactions, respectively, indicated that the urea‐forming reactions were more sensitive to the reaction temperature than the urethane‐forming reactions. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

The chain extension of anionic prepolymers in the preparation of aqueous poly(urethane–urea) dispersions

Anionic polyurethane prepolymers end‐capped with isocyanate groups were dispersed and chain‐extended in aqueous media using three different extension agents: hydrazine, 1,2‐ethylene diamine (EDA) and 1,2‐propylene diamine (PDA). Two types of prepolymer were used. The first was prepared from isophorone diisocyanate (IPDI), α,α‐dimethylol propionic acid (DMPA) and poly(propylene oxide) diol (PPO) and the second from α,α,α′,α′‐tetramethyl‐1,3‐xylylene diisocyanate (m‐TMXDI), poly(caprolactone) diol (PCL) and DMPA. The colloidal particles which formed in the dispersion process and the constituent poly(urethane–urea) chains were characterised by a combination of dynamic and static light scattering, gel permeation chromatography and FTIR spectroscopy. Using EDA as the extender, a study was made of how the degree of extension depended on the molar ratio of amine to isocyanate groups, [NH₂]/[NCO] (= R_{A, I}). It was found that using a stoichiometric balance of isocyanate and amine groups did not lead to high degree of extension, and better chain extension was obtained at lower R_{A, I} values. In a comparative study using stoichiometric balances of isocyanate and amine groups, the degrees of extension obtained using PDA and EDA were approximately the same, while hydrazine was the least effective. Force–extension studies were carried out on samples prepared from films cast from the aqueous poly(urethane–urea) dispersions in order to assess the influence of chain‐extender type and stoichiometry on bulk properties; values of Young's modulus, tensile strength and maximum extension are reported. Copyright © 2003 Society of Chemical Industry     

Thermal and mechanical characterization of maleimide‐functionalized copoly(urethane‐urea)s

Maleimide functionalized copoly(urethane‐urea)s were prepared by the reaction of a binary mixture of dibenzyldiisocyanate and 5‐maleimidoisophthalic diisocyanate with a macrodiol (PEGA‐2000), using diethylene glycol and trimethylol‐propane as chain extender and crosslinkers in toluene‐dichloromethane solutions at the ratio NCO/OH = 1.2. Structures of polymers were confirmed by IR spectroscopy and properties were studied by thermal and mechanical analysis (dynamic mechanical analysis (DMA), differential scanning calorimetry, thermogravimetric analysis, stress‐strain) and other physical methods. Maleimide modification increased the storage modulus and Young's modulus of copoly(urethane‐urea)s, slightly increased their glass transition temperature from ?10.6°C to ?6.3°C. Copoly(urethane‐urea) networks obtained by thermal polymerization of maleimide functions showed significantly increased of the mechanical properties. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Chromophoric poly(urea‐urethane)s with pendent 3‐hydroxynaphthalene group: Synthesis and characterization

The reaction of 4‐(3‐hydroxynaphthalene)‐1,2,4‐triazolidine‐3,5‐dione ( 3HNTD ) with n‐propylisocyanate was performed at different molar ratios. The resulting monosubstituted urea and disubstituted urea‐urethane derivatives were obtained in high yields and were used as model compounds for polymerization reactions. 3HNTD as a monomer was used in the preparation of heterocyclic poly(urea‐urethane)s to produce photoactive polymers, by polycondensation with different diisocyanates in N,N‐dimethylacetamide (DMAc) solution. Chromophoric heterocyclic polymers containing naphthalene group, obtained in quantitative yields, possessed inherent viscosities in the range of 0.14–0.38 dL/g. The resulting poly(urea‐urethane)s is insoluble in most organic solvents, but easily soluble in polar solvents such as dimethyl sulfoxide (DMSO), DMAc, and N‐methylpyrrolidone (NMP). The polymers were characterized by IR, ¹H‐NMR, elemental analysis, and TGA. Fluorimetric and UV–vis studies of the monomer as well as polymers were performed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Polyethylene‐block‐poly(ε‐caprolactone) diblock copolymers: synthesis and compatibility

A strategy is introduced for the synthesis of polyethylene‐block‐poly(ε‐caprolactone) block copolymers by a combination of coordination polymerization and ring‐opening polymerization. First, end‐hydroxylated polyethylene (PE‐OH) was prepared with a one‐step process through ethylene/3‐buten‐1‐ol copolymerization catalyzed by a vanadium(III) complex bearing a bidentate [N,O] ligand ([PhN?C(CH₃)CHC(Ph)O]VCl₂(THF)₂). The PE‐OH was then used as macroinitiator for ring‐opening polymerization of ε‐caprolactone, leading to the desired nonpolar/polar diblock copolymers. The block structure was confirmed by spectral analysis using ¹H NMR, gel permeation chromatography and differential scanning calorimetry. The unusual topologies of the model copolymers will establish a fundamental understanding for structure–property correlations, e.g. compatibilization, of polymer blends and surface and interface modification of other polymers. © 2014 Society of Chemical Industry     

Morphology and properties of poly(benzoxazine‐co‐urethane)s based on bisphenol‐S/aniline benzoxazine

Poly(benzoxazine‐co‐urethane) was prepared by melt‐blending bisphenol‐S/aniline‐type benzoxazine (BS‐a) with isocyanate‐terminated polyurethane (PU) prepolymer based on 2,4‐toluene diisocyanate and poly(ethylene glycol), followed by thermally activated polymerization of the blend. The copolymerization reaction between BS‐a and PU prepolymer was monitored using Fourier transform infrared spectroscopy. The morphology, dynamic mechanical properties, and thermal stability of the poly(benzoxazine‐co‐urethane) were studied using scanning electron microscopy, dynamic mechanical analysis, and thermogravimetry. Homogeneous morphology is shown in scanning electron micrographs of the fracture surfaces of poly(benzoxazine‐co‐urethane)s with different urethane weight fractions, and the roughness of the surface increases with urethane content increasing. Correspondingly, a single glass transition temperature (T_g) is shown on the dynamic mechanical analysis curves of the poly(benzoxazine‐co‐urethane)s, and the T_g is higher than that of the polybenzoxazine. With increase in the urethane content, the T_g and water absorption of poly(benzoxazine‐co‐urethane) increase, whereas the storage modulus and thermal stability decrease. POLYM. ENG. SCI., 53:2633–2639, 2013. © 2013 Society of Plastics Engineers     

Synthesis and biodegradability evaluation of 2‐methylene‐1,3‐dioxepane and styrene copolymers

Biodegradable copolymers of 2‐methylene‐1,3‐dioxepane (MDO) and styrene (ST) were synthesized by free‐radical copolymerization using di‐t‐butyl peroxide (DTBP) as the initiator. The copolymers containing ester units were characterized by Fourier transform infrared (FTIR), ¹H‐NMR, and ¹³C‐NMR spectroscopy. Their molecular weight and polydispersity index were determined by gel permeation chromatography (GPC). In vitro enzymatic degradation of poly(MDO‐co‐ST) was performed at 37°C in phosphate buffer solution (PBS, pH = 7.4) in the presence of Pseudomonas lipase or crude enzyme extracted from earthworm. The experiment showed that incorporating ester units into C? C backbone chain of polystyrene would result in a biodegradable copolymer. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1146–1151, 2007     

Synthesis and characterization of a poly(ether–ester) copolymer from poly(2,6 dimethyl‐1,4‐phenylene oxide) and poly(ethylene terephthalate)

A series of poly(ether–ester) copolymers were synthesized from poly(2,6 dimethyl‐1,4‐phenylene oxide) (PPO) and poly(ethylene terephthalate) (PET). The synthesis was carried out by two‐step solution polymerization process. PET oligomers were synthesized via glycolysis and subsequently used in the copolymerization reaction. FTIR spectroscopy analysis shows the coexistence of spectral contributions of PPO and PET on the spectra of their ether–ester copolymers. The composition of the poly(ether–ester)s was calculated via ¹H NMR spectroscopy. A single glass transition temperature was detected for all synthesized poly(ether–ester)s. T_g behavior as a function of poly(ether–ester) composition is well represented by the Gordon‐Taylor equation. The molar masses of the copolymers synthesized were calculated by viscosimetry. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Temperature influence on the behavior of polysulfone‐b‐poly(alkylene oxide)‐b‐poly(dimethylsiloxane) triblock copolymers in a selective solvent

Triblock copolymers containing polysulfone, poly(alkylene oxide), and poly(dimethylsiloxane) segments were obtained by addition of preformed α,ω‐bis(hydrogensilyl) poly(dimethylsiloxane) oligomers to alyl end‐capped poly(alkylene oxide)‐b‐polysulfone. Viscometric and UV absorption measurements were carried out in dilute 1,2‐dichlorethane solutions, in the temperature range of 20–75°C. The specific interactions exhibited by the block copolymers in a selective solvent are influenced by the copolymer composition and temperature. The results point to a conformational transition phenomenon, located around 55°C, which is attributed to the transition from a segregated to a pseudo‐Gaussian conformation through a compressed‐segregated conformation. POLYM. ENG. SCI., 57:114–118, 2017. © 2016 Society of Plastics Engineers     

13C NMR investigation of the reaction in water of UF resins with blocked emulsifiable isocyanates

A solid state ¹³C NMR study of hardened networks obtained by the reaction of blocked and nonblocked isocyanates (pMDI) with urea‐formaldehyde (UF) resins in water showed different results according to the temperature of the reaction. At high temperature, in water, both a nonblocked or an emulsifiable, blocked isocyanate, appear to crosslink with UF resins through the formation both of traditional methylene bridges connecting urea to urea and of urethane bridges. The latter have been confirmed by ¹³C NMR to form in water by reaction of the isocyanate ? N?C?O group with the hydroxymethyl groups of the UF resin. At ambient temperature, UF/pMDI resins where the pMDI is a emulsifiable blocked isocyanate, do not appear to form urethanes to any great extent but rather to crosslink through the usual UF resin urea to urea methylene bridges. Even in this case, when urethane bridges appear to be absent, evidence of crosslinking in water through reaction of the isocyanate with the ? NH₂ and ? NH? amide of the UF resin has not been observed. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 589–596, 2006     

Synthesis and kinetic studies of UV‐curable urethane‐acrylates

The UV‐curable urethane‐acrylates based on 2‐hydroxyethyl methacrylate (HEMA)‐terminated polyurethane (PU) for lithographic and coating applications are investigated in this study. Series of PU prepolymers were made from 4,4‐diphenyl methane diisocyanate (MDI), poly(propylene oxide) glycol (PPG 400), poly(butylene adipate)glycol (PBA 500), or poly(tetramethylene oxide) glycol (PTMO 1000) and are terminated with HEMA. The 2,2‐azobisisobutyronitrile (AIBN) was used as a UV‐initiator under air atmosphere. The curing kinetics of HEMA‐terminated PU film were studied. The curing analysis, using FTIR and reaction kinetics, indicate the reaction rate equation correlates well with the film thickness [T], initiator concentration [I], unreacted double bond concentration [C?C], and exposed energy [E] of the reaction system. The kinetic rate equation for the UV‐curable reaction can be written as © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3162–3166, 2004     

Synthesis and characterization of poly(urethane‐co‐imidine)s having pendent phenyl and benzylidene groups using bisphthalides,bislactones and blocked polyurethane prepolymers

Poly(urethane‐co‐imidine)s were prepared using amine blocked polyurethane (PU) prepolymer. The PU prepolymer was prepared by the reaction of poly(propylene glycol) (PPG₂₀₀₀) and 2,4‐tolylene diisocyanate (TDI) and end capped with N‐methyl aniline. The PU prepolymer was then reacted with bisphthalides and bislactones, until the evolution of carbon dioxide ceased. Polymerization reactions with bispthalides and bislactone took more time than with dianhydrides. Polymers were characterized by FTIR, GPC, TG and DSC analyses. Molecular weights of the poly(urethane‐co‐imidine)s were found to be lower than that of poly(urethane‐co‐imide)s. Compared to poly(urethane‐co‐imide)s all poly(urethane‐co‐imidine)s showed high glass transition temperature and crystallization peak in DSC. The thermal stability of the polyurethanes was found to increase with the introduction of imidine component. © 2001 Society of Chemical Industry     

Direct synthesis of new soluble and thermally stable poly(urethane‐imide)s from an imide ring‐containing dicarboxylic acid using diphenylphosphoryl azide

The direct preparation of various aromatic poly(urethane‐imide)s from 4‐p‐biphenyl‐2,6‐bis(4‐trimellitimidophenyl)pyridine (1) using diphenylphosphoryl azide (DPPA) was investigated. The polymers were mainly obtained by the conversion of imide ring‐containing diacid 1 to corresponding di(carbonyl azide) 2 with DPPA and then to diisocyanate 3 through the Curtius rearrangement of compound 2 followed by polyaddition of 3 in different amounts with aromatic dihydroxy compounds. The molecular weights of the resulting poly(urethane‐imide)s were evaluated viscometrically. All of the resulted polymers were thoroughly characterized by spectroscopic methods and elemental analyses. The poly(urethane‐imide)s exhibited an excellent solubility in a variety of polar solvents. Crystallinity nature of the polymers was estimated by means of WXRD. The glass‐transition temperatures of the polymers determined by DSC method were in the range of 191–202°C. The 10% weight loss temperatures of the poly(urethane‐imide)s from their thermal gravimetric analysis curves were found to be in the range of 392–416°C in nitrogen. The films of the resulting polymers were also prepared by casting the solution. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 869–877, 2006     

Cationic copolymerization behavior of a bicyclic orthoester having hydroxy group with glycidyl phenyl ether and volume change on their copolymerization

This article describes cationic ring‐opening copolymerization of a bicyclic orthoester having hydroxy group (BOE‐OH) and glycidyl phenyl ether (GPE), and the volume shrinkage behavior during the copolymerization. THF soluble polyethers [poly(BOE‐OH‐co‐GPE)] were obtained by the copolymerizations at 80–180°C, while crosslinked poly(BOE‐OH‐co‐GPE) was obtained by the copolymerizations at 220–250°C. This crosslinking reaction may originate from the dehydration of methylol groups in the side chain of poly(BOE‐OH‐co‐GPE). The volume shrinkage during the cationic copolymerization reduced as the increase of the BOE‐OH feed ratio. By contrast, the volume shrinkage on the crosslinking polymerization was almost independent on the BOE‐OH feed ratio. Poly(BOE‐OH‐co‐GPE)s with higher BOE‐OH composition showed lower thermal weight loss temperature owing to the release of H₂O by dehydration of methylol groups. The BOE‐OH component in the THF soluble poly(BOE‐OH‐co‐GPE)s lowered the glass transition temperature (T_g), while that in the crosslinked poly(BOE‐OH‐co‐GPE) increased the T_g probably because of the higher crosslinking density. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1356–1361, 2006     

Crosslinked acrylic pressure‐sensitive adhesives. II. Effect of humidity on the crosslinking reaction

The effect of humidity during storage on the crosslinking reactions of isocyanate groups was investigated with attenuated total reflectance Fourier transform infrared spectroscopy with pressure‐sensitive adhesives composed of poly[ethyl acrylate‐co‐(2‐ethylhexyl acrylate)‐co‐(2‐hydroxyethyl methacrylate)] as a base resin and polyisocyanate as a crosslinker. A peak‐resolving analysis of the amide II region revealed four bands. According to an analysis of the Fourier transform infrared spectra of the model compounds, these four bands were assigned to free urethane linkages, hydrogen‐bonded urethane linkages, free urea linkages, and hydrogen‐bonded urea linkages. As expected, storage under humid conditions led to the formation of free and hydrogen‐bonded urea linkages corresponding to the promotion of isocyanate consumption. Peak resolution of the amide II region was found to be a reasonable way of monitoring urethane and urea linkages during crosslinking reactions. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3039–3045, 2003     

Synthesis of polycarbonate‐co‐poly(p‐ethylphenol) and CdS nanocomposites

The enzyme‐catalyzed synthesis of poly(p‐ethylphenol) (PEP) was modified by copolymerization with polycarbonates through triphosgene at low temperature to form polycarbonate‐co‐poly(p‐ethylphenol) (PC‐co‐PEP). FTIR, NMR, GPC, and thermal analysis verified the formation of PC‐co‐PEP. The copolymers have an optical absorption in the UV range. CdS semiconductor nanocrystallites were synthesized in reversed micelles with subsequent in situ enzymatic copolymerization of p‐ethylphenol and 4‐hydroxythiophenol in the same medium. TEM and ATR–FTIR showed that the polymer precipitated in spherical morphologies, incorporating CdS nanocrystals into the polymer matrix, with surface hydroxyl groups. The polymer/CdS core was then dispersed into polycarbonate. The polymer/CdS nanocomposites showed higher optical aborbance in the UV‐vis range when compared to the polymer matrix without CdS. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 1851–1868, 1999