Morphology,thermal and mechanical behavior of polypropylene nanocomposites toughened with poly(ethylene‐co‐octene)

Rubber‐toughened polypropylene (PP) nanocomposites containing organophilic layered silicates were prepared by means of melt extrusion at 230 °C using a co‐rotating twin‐screw extruder in order to examine the influence of the organoclay and the addition of PP grafted with maleic anhydride (PPgMAH) as a compatibilizer on the morphological, mechanical and thermal properties. The mechanical properties of rubber‐toughened polypropylene nanocomposites (RTPPNCs) were studied through tensile, flexural and impact tests. Scanning electron microscopy (SEM) was used for investigation of the phase morphology and rubber particles size. X‐ray diffraction (XRD) was employed to characterize the formation of nanocomposites. The thermal properties were investigated by using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The dynamic mechanical properties were examined by using dynamic mechanical analysis (DMA). From the tensile and flexural tests, the optimum loading of organoclay in RTPP was found to be 6 wt%. The optimum loading of PPgMAH, based on the tensile and flexural properties, was also 6 wt%. The increase in the organoclay and PPgMAH content resulted in a severe embrittlement, manifested by a drop in the impact strength and tensile elongation at break. XRD studies revealed that intercalated RTPPNCs had been successfully prepared where the macromolecular PP segments were intercalated into the interlayer space of the organoclay. In addition, the organoclay was dispersed more evenly in the RTPPNC as the PPgMAH content increased. TGA results revealed that the thermal stability of the RTPPNC improved significantly with the addition of a small amount of organoclay. Copyright © 2006 Society of Chemical Industry     

Preparation of polyethylene‐octene elastomer/clay nanocomposite and microcellular foam processed in supercritical carbon dioxide

Polyethylene‐octene elastomer (POE)/organoclay nanocomposite was prepared by melt mixing of the POE with an organoclay (Cloisite 20A) in an internal mixer, using poly[ethylene‐co‐(methyl acrylate)‐co‐(glycidyl methacrylate)] copolymer (E‐MG‐GMA) as a compatibilizer. X‐ray diffraction and transmission electron microscopy analysis revealed that an intercalated nanocomposite was formed and the silicate layers of the clay were uniformly dispersed at a nanometre scale in the POE matrix. The nanocomposite exhibited greatly enhanced tensile and dynamic mechanical properties compared with the POE/clay composite without the compatibilizer. The POE/E‐MA‐GMA/clay nanocomposite was used to produce foams by a batch process in an autoclave, with supercritical carbon dioxide as a foaming agent. The nanocomposite produced a microcellular foam with average cell size as small as 3.4 µm and cell density as high as 2 × 10¹¹ cells cm^?3. Copyright © 2005 Society of Chemical Industry     

Crystallization behavior and mechanical properties of polypropylene random copolymer/poly(ethylene‐octene) blends

New polymer blends of polypropylene random copolymer (PP‐R) and poly(ethylene‐octene) (POE) were prepared by melt‐blending process using a corotating twin‐screw extruder. The POE content was varied up to 35%. The toughening efficiency of POE for PP‐R was evaluated by the mechanical properties of the resulted PP‐R/POE blends. The crystallization behavior and morphology of the blends were also studied. Results show that POE acts as nucleation agent to induce the crystallization of PP‐R matrix at higher crystallization temperature. Super‐toughened PP‐R/POE blends (Izod impact strength more than 500 J/m) can be readily achieved with only 10 wt % of POE. The high toughness of PP‐R/POE is attributed to cavitation and shear yielding of matrix PP‐R, as revealed by the morphology studies. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Polypropylene/metallocene ethylene‐octene copolymer blends with a bimodal particle size distribution: Mechanical properties and their controlling factors

Blends of polypropylene homopolymer (PP) and metallocene produced ethylene‐octene copolymer (EOR) with a bimodal particle size distribution were investigated. The aim of the work was to study the influences of EOR characteristics and its concentration on the tensile and impact properties of the blends. The matrix ligament thickness between rubber particles was measured and compared to those predicted using the theoretical models. The relationships between blend morphology and impact property were reported. It was found that the content of comonomer and molecular weight of the EOR as well as its concentration in the blends were the major factors controlling the tensile and impact properties of the blends. These factors became ineffective to impact property when the ligament thickness of the matrix was larger than the critical value (T ～0.3–0.4 μm). To achieve blends of high impact strength, the ligament thickness between rubber particles should be smaller than the critical value, and for a certain ligament thickness, EOR with high octene content and high molecular weight was preferred. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2412–2418, 2002     

Dynamically vulcanized blends of polypropylene and ethylene‐octene copolymer: Comparison of different peroxides on mechanical,thermal, and morphological characteristics

Thermoplastic vulcanizates (TPVs) are prepared by the dynamic vulcanization process, where crosslinking of an elastomer takes place during its melt mixing with a thermoplastic polymer under high shear. TPVs based on polypropylene (PP) with different grades of ethylene‐octene copolymers (EOC) were prepared with a coagent assisted peroxide crosslinking system. The effect of dynamic vulcanization and influence of various types and concentrations of peroxide were mainly studied on the basis of the mechanical, thermal, and morphological characteristics. Three structurally different peroxides, namely dicumyl peroxide (DCP), tert‐butyl cumyl peroxide (TBCP), and di‐tert‐butyl peroxy isopropyl benzene (DTBPIB) were investigated. The mechanical properties of the TPVs are primarily determined by the extent of crosslinking in the EOC and the degree of degradation in the PP phase. Among all peroxides used DCP gives best overall properties with low‐molecular‐weight EOC, whereas TBCP shows best property level with high‐molecular‐weight EOC‐based TPVs. These can be explained on the basis of the molecular characteristics of EOC and the nature of the peroxide used. Differential scanning calorimetery (DSC) and morphological analysis reveal that PP and EOC are a thermodynamically immiscible system. The melting endotherm was studied to determine the influence of various peroxides on crystallinity of the PP phase. Tensile fracture patterns were also analyzed to study the failure mechanism of the samples. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Rheological and thermal properties of binary blends of polypropylene and poly(ethylene‐CO‐1‐octene)

Dynamic viscoelastic properties of binary blends consisting of an isotactic polypropylene (i‐PP) and ethylene‐1‐octene copolymer (PEE) were investigated to reveal the relation between miscibility in the molten state and the morphology in the solid state. In this study, PEE with 24 wt % of 1‐octene was employed. The PEE/PP blend with high PEE contents showed two separate glass‐relaxation processes associated with those of the pure components. These findings indicate that the blend presents a two‐phase morphology in the solid state as well as in the molten state. The PEE/PP blend with low PEE content showed a single glass‐relaxation process, indicating that PEE molecules were probably incorporated in the amorphous region of i‐PP in the solid state. The DMTA analysis showed that the blends with low PEE contents presented only one dispersion peak, indicating a certain degree of miscibility between the components of these blends. These results are in accordance with the results of the rheological analysis. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1634–1639, 2001     

Novel intercalated nanocomposites of polypropylene/organic‐rectorite/polyethylene‐octene elastomer: Rheology,crystallization kinetics,and thermal properties

The melt blending method was applied to prepare ternary composites of polypropylene (PP)/organic‐rectorite (OREC)/polyethylene‐octene elastomer (POE) at constant content of 2 phr (parts per hundred PP) of OREC and 5, 10, 15 phr of POE (named PRE25, PRE210, and PRE215, separately) via twin‐screw extruder. At the same time the binary composites of OREC/PP at 2 phr loading of OREC, named PR2 were prepared in order to investigate effects of OREC and POE on rheology and crystallization properties of composites. The rheology was characterized on capillary rheometer, nonisothermal crystallization kinetics on differential scanning calorimetry (DSC), and thermal stability properties on thermogravimetric analysis (TG). It is found that melting PR2 and PRE systems conform to the law of Non‐Newton and shear‐thinning behavior is observed for both systems. The apparent viscosity of the melt decreases with the increase of POE loadings. The crystallization halftime (t_1/2) of PRE is shorter, the rate constant Zc larger, which indicates OREC and POE has the heterogeneous nucleation effect and the crystallization rate of PP was increased. The enthalpy of PRE is lower than that of PR2 and pure PP at the same conditions, which shows that the relative crystallinity of PRE composites are reduced. TG curves show that the ternary systems have higher thermal stability in contrast with pure PP. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1915–1921, 2005     

Morphology and mechanical properties of binary blends of polypropylene with statistical and block ethylene‐octene copolymers

In the present work, statistical (EOCs) and block (OBCs) ethylene‐octene copolymers, with similar densities and crystallinities, were used as impact modifiers of isotactic polypropylene (iPP), and the toughening effects of these two types of elastomers were compared. The viscosity curves of EOCs were similar to those of OBCs with equivalent melt flow rate (MFR), enabling a comparison of the viscosity ratio and elastomer type as independent variables. No distinct differences on the crystal forms and crystal perfection of iPP matrix in various blends were observed by thermal analysis. Morphological examination showed that OBCs form smaller dispersed domains than EOCs with similar MFRs. The flexural modulus, yield stress, stress and strain at break showed the same variation tendency for all the investigated polypropylene/elastomer blends. However, the room temperature Izod impact toughness of iPP/OBC blend was higher than that of iPP/EOC blend containing elastomer with the similar MFRs. The experimental results indicated that the compatibility of iPP/OBCs was much higher than that of iPP/EOCs. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Polypropylene nanocomposite film: A critical evaluation on the effect of nanoclay on the mechanical,thermal, and morphological behavior

Polypropylene (PP)/clay nanocomposites prepared by melt blending technique using different percentages of clay with and without maleic anhydride grafted PP (MA‐PP) were studied. The intercalated and exfoliated structure of nanocomposites was characterized by X‐Ray Diffraction (XRD) and transmission electron microscopy (TEM). Because of the typical intercalated and exfoliated structure, the tensile modulus of the nanocomposites were improved significantly as compared to virgin PP. The viscoelastic behavior of the nanocomposites was studied by dynamical mechanical analysis (DMA) and the results showed that with the addition of treated clay to PP there was substantial improvement in storage modulus increases. The thermal stability and crystallization of the PP nanocomposites as studied by differential scanning calorimeter (DSC) and thermo gravimetric analysis (TGA) were also improved significantly compared to PP. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Polypropylene‐organoclay nanocomposite: Preparation,microstructure, and mechanical properties

A series of polypropylene (PP) nanocomposites containing 2, 4, and 6 wt % of an organophilic montmorillonite clay was prepared via direct melt mixing in the presence of maleic anhydride grafted polypropylene (PP‐g‐MAH) as compatibilizing agent. Microstructure characterization was performed by X‐ray diffraction analysis. Nanocomposites exhibited a 15 and 22% enhancement in tensile modulus and impact strength, respectively. The heat deflection temperature of PP nanocomposites was 36°C greater than for pure PP. Thermal and mechanical properties of nanocomposites were compared to properties of traditional PP‐talc and PP‐glass fiber composites. The results showed that the properties of nanocomposites improved compared to ordinary polypropylene composites. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of nano‐silica filler on the rheological and morphological properties of polypropylene/liquid‐crystalline polymer blends

A fumed hydrophilic nano‐silica‐filled polypropylene (PP) composite was blended with a liquid‐crystalline polymer (LCP; Rodrun LC5000). The preblended polymer blend was extruded through a capillary die; this was followed by a series of rheological and morphological characterizations. The viscosity of the PP matrix increased with the addition of the hydrophilic nano‐silica. At shear rates between 50 and 200 s^?1, the composite displays marked shear‐thinning characteristics. However, the incorporation of LC5000 in the PP composite eliminated the shear‐thinning characteristic, which suggests that LC5000 destroyed the agglomerated nano‐silica network in the PP matrix. Although the viscosity ratio of LCP/PP was reduced after the addition of nano‐silica fillers, the LCP phases existed as droplets and ellipsoids. The nano‐silicas were concentrated in the LC5000 phase, which hindered the formation of LCP fibers when processed at high shear deformation. We carried out surface modification of the hydrophilic nano‐silica to investigate the effect of modified nano‐silica (M‐silica) on the morphology of the PP/LC5000 blend system. Ethanol was successfully grafted onto the nano‐silica surface with a controlled grafting ratio. The viscosity was reduced for PP filled with ethanol‐M‐silica when compared to the system filled with untreated hydrophilic nano‐silica. The LC5000 in the (PP/M‐silica)/LC5000 blend existed mainly in the form of fibrils. At high shear rates (e.g., 3000 s^?1), the LC5000 fibril network was formed at the skin region of the extrudates. The exclusion of nano‐silica in the LC5000 phase and the increased viscosity of the matrix were responsible for the morphological changes of the LCP phase. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1484–1492, 2003     

Study on poly(propylene)/ammonium polyphosphate composites modified by ethylene‐1‐octene copolymer grafted with glycidyl methacrylate

The compatibilization effect of ethylene‐1‐octene copolymer grafted with glycidyl methacrylate (POE‐g‐GMA) as an interface compatibilizer on the mechanical and combustion properties, and the morphology and structures of the cross sections of ammonium polyphosphate (APP)–filled poly(propylene) (PP) were investigated by thermogravimetry, dynamic mechanical analysis, and differential scanning calorimetry. The results indicated that the toughness of the PP/APP composites increased rapidly with adding POE‐g‐GMA; the dynamic mechanical spectra revealed that the increase of the toughness was closely related to the peaks of loss modulus (E″) and mechanical loss (tan δ). The improvement of the dispersion of APP in the PP matrix was attributed to the addition of POE‐g‐GMA; it was found that the interfacial adhesion between the filler and matrix was enhanced when the grafting material was added to the composites. Under such circumstances, the ratio of char formation was increased when the PP composites were heated, although the content of flame retardant was not changed, so the flame retardance of the material was improved. The addition of POE‐g‐GMA increased the rate of crystallization. At the same time, the degree of crystallinity and the temperature at the beginning of crystallization were decreased, although exerting little influence on the melt behavior of the crystallization of the composites. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 412–419, 2004     

Dynamically vulcanized blends of polypropylene and ethylene octene copolymer: Influence of various coagents on mechanical and morphological characteristics

Dynamically cured blends of polypropylene (PP) and ethylene octene copolymer (EOC) with coagent‐assisted peroxide curative system were prepared by melt‐mixing method. It was well established that PP exhibits β‐chain scission in the presence of peroxide. Principally, incorporation of a coagent increases the crosslinking efficiency in the EOC phase and decreases the extent of degradation in the PP phase. The present study mainly focused on the influence of three structurally different coagents, namely, triallyl cyanurate (TAC), trimethylol propane triacrylate (TMPTA), and N,N′‐m‐phenylene dimaleimide (MPDM), on the mechanical properties of the PP/EOC thermoplastic vulcanizates (TPVs). The reactivity and efficiency of different coagents were characterized by cure study on EOC gum vulcanizate. TAC showed the highest torque values followed by MPDM and TMPTA. Significant improvements in the physical properties of the TPVs were inferred with the addition of coagents. Among the three coagents used, MPDM showed the best balance of mechanical properties in these TPVs. The results indicated that torque values obtained during mixing and the final mechanical properties can be correlated. Different aspects were explained for the selection of a coagent that forms a product with desired properties. The phase morphologies of the TPVs prepared were studied by scanning electron microscopy. Tensile fracture patterns were also analyzed to study the failure mechanism of the samples. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of the high‐density polyethylene melt index on the microcellular foaming of high‐density polyethylene/polypropylene blends

The effect of high‐density polyethylene (HDPE)/polypropylene (PP) blending on the crystallinity as a function of the HDPE melt index was studied. The melting temperature and total amount of crystallinity in the HDPE/PP blends were lower than those of the pure polymers, regardless of the blend composition and melt index. The effects of the melt index, blending, and foaming conditions (foaming temperature and foaming time) on the void fractions of HDPEs of various melt indices and HDPE/PP blends were also investigated. The void fraction was strongly dependent on the foaming time, foaming temperature, and blend composition as well as the melt index of HDPE. The void fraction of the foamed 30:70 HDPE/PP blend was always higher than that of the foamed 50:50 HDPE/PP blend, regardless of the melt index. The microcellular structure could be greatly improved with a suitable ratio of HDPE to PP and with foaming above the melting temperature for long enough; however, using high‐melt‐index HDPE in the HDPE/PP blends had a deleterious effect on both the void fraction and cell morphology of the blends. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 364–371, 2004     

Carbon nanotube/polypropylene/polycarbonate conductive nanocomposite films: Preparation and characterization

In this study, CNT/PP/PC conductive composite films were prepared by compounding PP (polypropylene)/PC (polycarbonate) (1:1) and carbon nanotubes (CNT) using a physical blending and hot pressing method. Next, Fourier transform infrared spectroscopy, thermogravimetric analysis, differential scanning calorimetry, and water contact angle measurement are conducted in order to characterize the properties of CNT/PP/PC conductive films. The results showed there is no chemical reaction inside the PP/PC composite film with the addition of CNT. Neither the CNT composite film containing 3 wt% nor the control film decomposed thermally within 220°C. The water contact angle increased from 88.5° for the control film to 110.99° for the composite film containing 3 wt% CNT. This indicates that the film has good thermal stability and hydrophobic properties. The percolation threshold was obtained when the content of CNT was 3 wt%, and the best conductivity of the CNT/PP/PC composite film was 5.53 S/m at this time. In order to improve the tensile properties of the film, a small amount of polyurethane (TPU) was added to the film, and the maximum tensile strength was 24.91 Mpa when the content of TPU was 6.7%. This study can provide a strategy for the practical application of flexible electronic devices.     

Study on processing of ultrahigh molecular weight polyethylene/polypropylene blends

The processing of ultrahigh molecular weight polyethylene (UHMWPE) by the addition of polypropylene (PP) and high‐density polyethylene (HDPE) was investigated. The results show that the addition of PP improves the processability of UHMWPE more effectively than does the addition of HDPE. UHMWPE/PP blends can be effectively processed with a twin‐roller and general single‐screw extruder. In the extrusion of UHMWPE/PP blends, PP is enriched at the surface of the blend adjacent to the barrel wall, thus increasing the frictional force on the wall; the conveyance of the solid down to the channel can then be carried out. The melt pool against the active flight flank exerts a considerable pressure on the UHMWPE powder in the passive flight flank, which overcomes the hard compaction of UHMWPE. The PP penetrates into the gaps between the particles, acting as a heat‐transfer agent and adhesive, thus enhancing the heat‐transfer ability in the material. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 977–985, 2004     

Nonisothermal crystallization,melting behavior,and morphology of polypropylene/metallocene‐catalyzed polyethylene blends

The nonisothermal crystallization, melting behavior, and morphology of blends of polypropylene (PP) and a metallocene‐catalyzed polyethylene (mPE) elastomer were studied with differential scanning calorimetry, scanning electron microscopy, polarized optical microscopy, and X‐ray diffraction. The results showed that PP and mPE were partially miscible and could form some cocrystallization, although the extent was very small. A modified Avrami analysis and the Mo method were used to analyze the nonisothermal crystallization kinetics of the blends. The values of the Avrami exponent indicated that the crystallization nucleation of the blends was homogeneous, the growth of the spherulites was three‐dimensional, and the crystallization mechanism of PP was not affected by mPE. The crystallization activation energy was estimated with the Kissinger method. Interesting results were obtained with the modified Avrami analysis and Mo and Kissinger methods, and the conclusions were in good agreement. The addition of less mPE increased the overall crystallization rate of PP. The relationship between the composition and morphology of the blends was examined. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1203–1210, 2004     

Thermal and mechanical properties of a polypropylene nanocomposite

An experimental polypropylene (PP) nanocomposite, containing approximately 4 wt % of an organophilic montmorillonite clay, was prepared and characterized, and its properties were compared with those of talc‐filled (20–40 wt %) compositions. Weight reduction, with maintained or even improved flexural and tensile moduli, especially at temperatures up to 70°C, was a major driving force behind this work. By a comparison with the analytical data from a nylon 6 (PA‐6) nanocomposite, it was found that the PP nanocomposite contained well‐dispersed, intercalated clay particles; however, X‐ray diffraction, transmission electron microscopy, dynamic mechanical analysis, and permeability measurements confirmed that exfoliation of the clay in PP was largely absent. The increased glass‐transition temperature (T_g) of a PA‐6 nanocomposite, which possessed fully exfoliated particles, indicated the molecular character of the matrix–particle interaction, whereas the PP nanocomposite exhibited simple matrix–filler interactions with no increase in T_g. The PP nanocomposite exhibited a weight reduction of approximately 12% in comparison with the 20% talc‐filled PP, while maintaining comparable stiffness. Undoubtedly, considerable advantages may be available if a fully exfoliated PP nanocomposite is fabricated; however, with the materials available, a combination of talc, or alternative reinforcements, and nanocomposite filler particles may provide optimum performance. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1639–1647, 2003     

Melting,nonisothermal crystallization behavior and morphology of polypropylene/random ethylene—propylene copolymer blends

The melting, nonisothermal crystallization behavior and morphology of blends of polypropylene (PP) with random ethylene–propylene copolymer (PP‐R) were studied by differential scanning calorimetry, polarized optical microscopy, scanning electron microscopy, and X‐ray diffraction. The results showed that PP and PP‐R were very miscible and cocrystallizable. Modified Avrami analysis was used to analyze the nonisothermal crystallization kinetics of the blends. The values of the Avrami exponent indicated that the crystallization nucleation of the blends was heterogeneous, the growth of the spherulites was tridimensional, and the crystallization mechanism of PP was not affected by PP‐R. The crystallization activation energy was estimated using the Kissinger method. An interesting result was obtained with the modified Avrami analysis and the Kissinger method, whose conclusions were in good agreement. The addition of a minor PP‐R phase favored an increase in the overall crystallization rate of PP. Maximum enhancing effect wass found to occur with a PP‐R content of 20 wt %. The relationship between the composition and the morphology of the blends is discussed. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 670–678, 2006     

Effect of organo‐modified layered silicates on flammability performance of high‐density polyethylene/rice husk flour nanocomposite

This research was carried out to investigate on the effect of organomodified montmorillonite (OMMT) on the flame retarding characteristics and clay dispersion of composites based on high‐density polyethylene and rice husk flour. To meet this objective, the blend nanocomposites were prepared through the melt mixing of high‐density polyethylene and rice husk flour at 50% weight ratios, with various amounts of OMMT (0, 2, 4, and 6 per hundred compounds) in Hakee internal mixer; then, the samples were made by injection molding. Results indicated that the burning rate, total smoke production, and heat release rate of samples decreased with increasing the OMMT content. Also, the char residue and time to ignition increased with increasing the nanoclay loading. X‐ray diffraction patterns revealed that the nanocomposites formed were intercalated. Also, morphological findings showed that samples containing 2 per hundred compounds of OMMT had higher order of intercalation and better dispersion. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011