ABA triblock copolymers from poly(p‐dioxanone) and poly(ethylene glycol)

Poly(p‐dioxanone)–poly(ethylene glycol)–poly(p‐dioxanone) ABA triblock copolymers (PEDO) were synthesized by ring‐opening polymerization from p‐dioxanone using poly(ethylene glycol) (PEG) with different molecular weights as macroinitiators in N₂ atmosphere. The copolymer was characterized by ¹H NMR spectroscope. The thermal behavior, crystallization, and thermal stability of these copolymers were investigated by differential scanning calorimetry and thermogravimetric measurements. The water absorption of these copolymers was also measured. The results indicated that the content and length of PEG chain have a greater effect on the properties of copolymers. This kind of biodegradable copolymer will find a potential application in biomedical materials. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:1092–1097, 2006     

Biodegradability of poly(ethylene terephthalate) copolymers with poly(ethylene glycol)s and poly(tetramethylene glycol)

Poly(ethylene terephthalate) copolymers were prepared by melt polycondensation of dimethyl terephthalate and excess ethylene glycol with 10–40mol% (in feed) of poly(ethylene glycol) (E) and poly(tetramethylene glycol) (B), with molecular weight (MW) of E and B 200–7500 and 1000, respectively. The reduced specific viscosity of copolymers increased with increasing MW and content of polyglycol comonomer. The temperature of melting (T_m), cold crystallization and glass transition (T_g) decreased with the copolymerization. T_m depression of copolymers suggested that the E series copolymers are the block type at higher content of the comonomer. T_g was decreased below room temperature by the copolymerization, which affected the crystallinity and the density of copolymer films. Water absorption increased with increasing content of comonomer, and the increase was much higher for E1000 series films than B1000 series films. The biodegradability was estimated by weight loss of copolymer films in buffer solution with and without a lipase at 37°C. The weight loss was enhanced a little by the presence of a lipase, and increased abruptly at higher comonomer content, which was correlated to the water absorption and the concentration of ester linkages between PET and PEG segments. The weight loss of B series films was much lower than that of E series films. The abrupt increase of the weight loss by alkaline hydrolysis is almost consistent with that by biodegradation.     

Biodegradable and photocurable multiblock copolymers with shape‐memory properties from poly(ε‐caprolactone) diol,poly(ethylene glycol), and 5‐cinnamoyloxyisophthalic acid

Biodegradable and photocurable multiblock copolymers of various compositions were synthesized by the high‐temperature solution polycondensation of poly(ε‐caprolactone) (PCL) diols of molecular weight (M_n) = 3000 and poly(ethylene glycol)s (PEG) of M_n = 3000 with a dichloride of 5‐cinnamoyloxyisophthalic acid (ICA) as a chain extender, followed by irradiation by a 400 W high‐pressure mercury lamp (λ > 280 nm) to form a network structure. The gel contents increased with photocuring time, reaching a level of over 90% after 10 min for all copolymers without a photoinitiator. The thermal and mechanical properties of the photocured copolymers were examined by DSC and tensile tests. In cyclic thermomechanical tensile tests, the photocured ICA/PCL/PEG copolymer films showed good shape‐memory properties at 37–60°C, with both shape fixity ratio and shape recovery ratio over 90% at a maximum tensile strain of 100–300%. The water absorption of these copolymers and their rate of degradation in a phosphate buffer solution (pH 7.0) at 37°C increased significantly with increasing PEG content. The novel photocured ICA/PCL/PEG multiblock copolymers are potentially useful in biomedical applications. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and characterization of novel block copolymer from trans‐4‐hydroxy‐L‐proline and poly(ethylene glycol)

A series of novel ABA‐type block copolymers were synthesized by polymerization of trans‐4‐hydroxy‐L ‐proline (HyP) in the presence of various molecular weight poly(ethylene glycol)s (PEGs), a bifunctional OH‐terminated PEG using stannous octoate as catalyst. The optimal reaction conditions for the synthesis of the copolymers were obtained with 5 wt % stannous octoate at 140°C under vacuum (20 mmHg) for 24 h. The synthesized copolymers were characterized by IR spectroohotometry, proton nuclear magnetic resonance, differential scanning calorimetry, and Ubbelohde viscometer. The glass transition temperature (T_g) of the copolymers shifted to significantly higher temperature with increasing the number average degree of polymerization and HyP/PEO molar ratio. In contrast, the melting temperature (T_m) decreased with increasing the HyP/PEO molar ratio. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1581–1587, 2001     

Synthesis and characterization of poly(ether ketone ketone) (PEKK)/sodium sulfonated poly(arylene ether ketone) (S‐PAEK) block copolymers

A series of well‐defined poly(ether ketone ketone) (PEKK)/sodium sulfonated poly(aryl ether ketone) (S‐PAEK) block copolymers of high molecular weights was prepared by direct nucleophilic polymerization of hydroquinone with sodium 5,5′‐carbonylbis(2‐fluorobenzene sulfonate) ( 1 ) and PEKK oligomer ( 2 ). Varying the ratio of 1 to 2 used in polymerization can be used to control the degree of polymer sulfonation, which correspondingly affects the polymer solubility in solvents. Increasing content of 1 in the copolymers, slightly decreases their thermal stability which is nevertheless thermally stable up to 400 °C. Two T_g values, or one broad T_g, were observed in the DSC measurements of the block copolymers, indicating the existence of phase separation, which was further proved by phase‐separated morphologies as shown in atomic force microscopy images. © 2001 Society of Chemical Industry     

Hydrolytic Degradation of Aliphatic Polyesters Copolymerized with Poly(ethylene glycol)s

Poly(1,4-butanediol succinate) copolymers were prepared by melt polycondensation of succinic acid and 1,4-butanediol with 10–50mol% (in feed) of poly(ethylene glycol) (PEG), where molecular weight (MW) of PEG is 200–2000. The reduced specific viscosity of the copolymers increased with incorporation of the PEG component, but a higher PEG content in the copolymers reduced it. The temperature of melting (T_m) and crystallinity decreased with increasing PEG content. T_m depression of the copolymers followed approximately Flory’s equation, suggesting that these are random type copolymers. Tensile strength and elongation decreased with increasing MW and content of PEG. The weight loss of copolymer films in a buffer solution with or without lipase at 37°C, as well as water absorption, increased with increasing PEG content, implying that higher water absorption contributes to hydrolytic degradation of the films. However, the weight loss of copolymers with PEG of lower MW increased greatly in spite of lower water absorption, demonstrating that hydrolytic degradation is influenced by the concentration of degradable ester linkages between succinic acid and PEG segments rather than water absorption. © of SCI.     

Crystallization and morphology of cholesterol end‐capped poly(ethylene glycol)

Crystallization and morphology of polyethylene glycol with molecular weight M_n = 2000 (PEG2000) capped with cholesterol at one end (CS‐PEG2000) and at both ends (CS‐PEG2000‐CS) were investigated. It is found that the bulky cholesteryl end group can retard crystallization rate and decrease crystallinity of PEG, especially for CS‐PEG2000‐CS. Isothermal crystallization kinetics shows that the Avrami exponent of CS‐PEG2000 decreases as crystallization temperature (T_c). The Avrami exponent of CS‐PEG2000‐CS increases slightly with T_c, but it is lower than that of CS‐PEG2000. Compared to the perfect spherulite morphology of PEG2000, CS‐PEG2000 exhibits irregular and leaf‐like spherulite morphology, while only needle‐like crystals are observed in CS‐PEG2000‐CS. The linear growth rate of CS‐PEG2000 shows a stronger dependence on T_c than PEG2000. The cholesterol end group alters not only the free energy of the folding surface, but also the temperature range of crystallization regime. The small angle X‐ray scattering (SAXS) results show that lamellar structures are formed in all these three samples. By comparing the long periods obtained from SAXS with the theoretically calculated values, we find that the PEG chains are extended in PEG2000 and CS‐PEG2000, but they are once‐folded in CS‐PEG2000‐CS. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2464–2471, 2007     

Crystallization behavior and morphology of double crystalline poly(trimethylene terephthalate)/poly(ethylene oxide terephthalate) copolymers

Double crystalline poly(trimethylene terephthalate)/poly(ethylene oxide terephthalate) copolymers (PTT/PEOT), with PTT content ranging from 16.5 to 65.5 wt%, were synthesized by melt copolycondensation. The morphological transformation of samples from microphase separation to macrophase separation was investigated by gel permeation chromatography and transmission electron microscopy. Differential scanning calorimetry and in situ wide‐angle X‐ray diffraction suggested that all copolycondensation samples displayed double crystalline behavior. The melt‐crystallization peak temperatures (T_{m, c} values) of PTT chains monotonously increased with increasing PTT content and were higher than that of homo‐PTT when the content of PTT was above 30.6 wt%. Interestingly, T_{m, c} values of PEOT chains were also increased with increasing PTT content. Polarized optical microscopy revealed that all copolycondensation samples studied could form ring‐banded spherulites and band spacing increased with increasing T_c values. In addition, band spacing decreased with increasing PTT content at a given T_c. Strangely, although PEOT was the main component in all copolycondensation samples, spherulitic morphology formed by the advance crystallization of PTT did not change after PEOT crystallization. Only a subtle change of quadrant tones was detected. © 2012 Society of Chemical Industry     

Synthesis and characterization of a poly(ether–ester) copolymer from poly(2,6 dimethyl‐1,4‐phenylene oxide) and poly(ethylene terephthalate)

A series of poly(ether–ester) copolymers were synthesized from poly(2,6 dimethyl‐1,4‐phenylene oxide) (PPO) and poly(ethylene terephthalate) (PET). The synthesis was carried out by two‐step solution polymerization process. PET oligomers were synthesized via glycolysis and subsequently used in the copolymerization reaction. FTIR spectroscopy analysis shows the coexistence of spectral contributions of PPO and PET on the spectra of their ether–ester copolymers. The composition of the poly(ether–ester)s was calculated via ¹H NMR spectroscopy. A single glass transition temperature was detected for all synthesized poly(ether–ester)s. T_g behavior as a function of poly(ether–ester) composition is well represented by the Gordon‐Taylor equation. The molar masses of the copolymers synthesized were calculated by viscosimetry. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Synthesis and characterization of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers with dibutylmagnesium as catalyst

Two series of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers were prepared by the ring opening polymerization of ε‐caprolactone in the presence of poly(ethylene glycol) and dibutylmagnesium in 1,4‐dioxane solution at 70°C. The triblock structure and molecular weight of the copolymers were analyzed and confirmed by ¹H NMR, ¹³C NMR, FTIR, and gel permeation chromatography. The crystallization and thermal properties of the copolymers were investigated by wide‐angle X‐ray diffraction (WAXD) and differential scanning calorimetry (DSC). The results illustrated that the crystallization and melting behaviors of the copolymers were depended on the copolymer composition and the relative length of each block in copolymers. Crystallization exothermal peaks (T_c) and melting endothermic peaks (T_m) of PEG block were significantly influenced by the relative length of PCL blocks, due to the hindrance of the lateral PCL blocks. With increasing of the length of PCL blocks, the diffraction and the melting peak of PEG block disappeared gradually in the WAXD patterns and DSC curves, respectively. In contrast, the crystallization of PCL blocks was not suppressed by the middle PEG block. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Comparison of micelles formed by amphiphilic poly(ethylene glycol)‐b‐poly(trimethylene carbonate) star block copolymers

In this article, we describe the synthesis and solution properties of PEG‐b‐PTMC star block copolymers via ring‐opening polymerization (ROP) of trimethylene carbonate (TMC) monomer initiated at the hydroxyl end group of the core PEG using HCl Et₂O as a monomer activator. The ROP of TMC was performed to synthesize PEG‐b‐PTMC star block copolymers with one, two, four, and eight arms. The PEG‐b‐PTMC star block copolymers with same ratio of between hydrophobic PTMC and hydrophilic PEG segments were obtained in quantitative yield and exhibited monomodal GPC curves. The amphiphilic PEG‐b‐PTMC star block copolymers formed spherical micelles with a core–shell structure in an aqueous phase. The mean hydrodynamic diameters of the micelles increased from 17 to 194 nm with increasing arm number. As arm number increased, the critical micelle concentration (CMC) of the PEG‐b‐PTMC star block copolymers increased from 3.1 × 10^?3 to 21.1 × 10^?3 mg/mL but the partition equilibrium constant, which is an indicator of the hydrophobicity of the micelles of the PEG‐b‐PTMC star block copolymers in aqueous media, decreased from 4.44 × 10⁴ to 1.34 × 10⁴. In conclusion, we confirmed that the PEG‐b‐PTMC star block copolymers form micelles and, hence, may be potential hydrophobic drug delivery vehicles. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis functional poly(carbonate‐b‐ester) copolymers and micellar characterizations

Functional poly(carbonate‐b‐ester)s were synthesized in buck by ring‐opening polymerization of the carbonate (TMC, MBC, or BMC) with tert‐butyl N‐(2‐hydroxyethyl) carbamate as an initiator, and then with ε‐CL (or ε‐BCL) comonomer. Subsequently, the PMMC‐b‐PCL with pendent carboxyl groups and the PTMC‐b‐PHCL with pendent hydroxyl groups were obtained by catalytic debenzylation. DSC analysis indicated that only one T_g at an intermediate temperature the T_gs of the two polymer blocks. A decrease T_g was observed when an increase contents of ε‐CL incorporated into the copolymers. In contrast, two increased T_ms were observed with increasing PCL content. The block copolymers formed micelle in aqueous phase with critical micelle concentrations (cmcs) in the range of 2.23–14.6 mg/L and with the mean hydrodynamic diameters in the range of 100–280 nm, depending on the composition of copolymers. The drug entrapment efficiency and hydrolytic degradation behavior of micelle were also evaluated. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Synthesis and characterization of poly(ϵ‐caprolactone)‐b‐poly(ethylene glycol) block copolymers prepared by a salicylaldimine‐aluminum complex

A series of poly(?‐caprolactone)‐b‐poly(ethylene glycol) (PCL‐b‐PEG) block copolymers with different molecular weights were synthesized with a salicylaldimine‐aluminum complex in the presence of monomethoxy poly(ethylene glycol). The block copolymers were characterized by ¹H NMR, GPC, WAXD, and DSC. The ¹H NMR and GPC results verify the block structure and narrow molecular weight distribution of the block copolymers. WAXD and DSC results show that crystallization behavior of the block copolymers varies with the composition. When the PCL block is extremely short, only the PEG block is crystallizable. With further increase in the length of the PCL block, both blocks can crystallize. The PCL crystallizes prior to the PEG block and has a stronger suppression effect on crystallization of the PEG block, while the PEG block only exerts a relatively weak adverse effect on crystallization of the PCL block. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis and surface properties of polystyrene‐graft‐poly(ethylene glycol) copolymers

Polystyrene‐graft‐poly(ethylene glycol) copolymers (PS‐g‐PEG) were successfully synthesized using the “grafting‐through” method. The graft copolymers and the surface properties of their coats were characterized by 1 H‐NMR, gel permeation chromatography (GPC), differential scanning calorimetry (DSC), transmission electron microscopy (TEM), X‐ray photoelectron spectroscopy (XPS), static contact angle measurement, and atomic force microscopy (AFM). Both DSC and TEM indicated that the graft copolymers had a microphase separated structure. AFM showed the microphase separated structure also occurred at the coat surface, especially at high PEG content, which could also be indirectly confirmed by the XPS and contact angle results. The formation mechanism of the microphase separated structure was discussed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1458–1465, 2007     

Crystallization kinetics of novel poly(aryl ether ketone) copolymers containing 2,7‐naphthalene moieties

To increase the glass transition temperature (T_g) of poly(aryl ether ketone), and to decrease the melting temperature (T_m) and temperature of processing, a series of novel poly(aryl ether ketone)s with different contents of 2,7‐naphthalene moieties (PANEK) was synthesized. We focused on the influence of the naphthalene contents to the copolymer's crystallization. The crystallization kinetics of the copolymers was studied isothermally and nonisothermally by differential scanning calorimetry. In the study of isothermal crystallization kinetics, the Avrami equation was used to analyze the primary process of the crystallization. The study results of the crystallization of PANEK at cooling/heating rates ranging from 5 to 60°C/min under nonisothermal conditions are also reported. Both the Avrami equation and the modified Avrami–Ozawa equation were used to describe the nonisothermal crystallization kinetics of PANEK. The results show that the increase in the crystallization temperature and the content of 2,7‐naphthalene moieties will make the crystallization rate decrease, while the nucleation mechanism and the crystal growth of PANEK are not influenced by the increasing of the content of 2,7‐naphthalene moieties. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2527–2536, 2006     

The effect of poly(ethylene glycol) mixed with poly(l‐lactic acid) on the crystallization characteristics and properties of their blends

The non‐isothermal and isothermal crystallizations of extruded poly(l ‐lactic acid) (PLLA) blends with 10, 20 and 30 wt% poly(ethylene glycol) (PEG) were investigated with differential scanning calorimetry. The formation of α‐form crystals in the blend films was verified using X‐ray diffraction and an increase in crystallinity indexes using Fourier transformation infrared spectroscopy. Crystallization and melting temperatures and crystallinity of PLLA increased with decreasing cooling rate (CR) and showed higher values for the blends. Although PLLA crystallized during both cooling and heating, after incorporation of PEG and with CR = 2 °C min^?1 its crystallization was completed during cooling. Increasingly distinct with CR, a small peak appeared on the lower temperature flank of the PLLA melting curve in the blends. A three‐dimensional nucleation process with increasing contribution from nuclei growth at higher CR was verified from Avrami analysis, whereas Kissinger's method showed that the diluent effect of 10 and 20 wt% PEG in PLLA decreased the effective energy barrier. During isothermal crystallization, crystallization half‐time increased with temperature (T_ic) for the blends, decreased with PEG content and was lower than that of pure PLLA. In addition, the Avrami rate constants were significantly higher than those of pure PLLA, at the lower T_ic. Different crystal morphologies in the PLLA phase were formed, melting in a broader and slightly higher T_m range than pure PLLA. The crystallization activation energy of PLLA decreased by 56% after the addition of 10 wt% PEG, increasing though with PEG content. Finally, PEG/PLLA blends presented improved flexibility and hydrophilicity. © 2019 Society of Chemical Industry     

Characterization and comparison of diblock and triblock amphiphilic copolymers of poly(δ‐valerolactone)

Three types of pegylated amphiphilic copolymers of poly(δ‐valerolactone) (PVL) were copolymerized with methoxy poly(ethylene glycol) (MePEG) and poly(ethylene glycol) (PEG₄₀₀₀ and PEG_10,000), respectively. Pegylation of PVL allowed copolymers possessing amphiphilic property and efficiently self‐assembled to form micelles with a low critical micelle concentration (CMC) in the range of 10^?7–10^?8M. The average molecular weight of copolymers was in the range of 10,000–20,000 Da, and the polydispersity of copolymers was about 1.7–1.8. Higher mobility of low molecular weight PEG (i.e., MePEG and PEG₄₀₀₀) than high molecular weight PEG_10,000 allowed valerolactone ring opening more efficient in terms of PVL/MePEG and PVL/PEG₄₀₀₀ copolymers possessing longer chain length in hydrophobic domain. Pegylated PVL with low CMC and triblock structure was preferred to encapsulate drug during micelle formation. Although all of these amphiphilic copolymers exhibited controlled release character, the micelles formed by triblock copolymer possessed a more stable core‐shell conformation than that by diblock copolymer, and resulted in the release of drug from triblock micelles slower than that from diblock micelles. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1836–1841, 2006     

Synthesis and characterization of poly(ether ketone ether ketone ketone)/poly(ether ether ketone ketone) copolymers containing naphthalene and pendant cyano groups

2,6‐Bis(β‐naphthoxy)benzonitrile (BNOBN) was synthesized by reaction of β‐naphthol with 2,6‐difluorobenzonitrile in N‐methyl‐2‐pyrrolidone (NMP) in the presence of KOH and K₂CO₃. Poly(ether ketone ether ketone ketone)(PEKEKK) /poly(ether ether ketone ketone) (PEEKK) copolymers containing naphthalene and pendant cyano groups were obtained by electrophilic Friedel‐Crafts polycondensation of terephthaloyl chloride (TPC) with varying mole proportions of 4,4′‐diphenoxybenzophenone (DPOBP) and 2,6‐bis(β‐naphthoxy)benzonitrile (BNOBN) using 1,2‐dichloroethane (DCE) as solvent and NMP as Lewis base in the presence of anhydrous AlCl₃. The resulting polymers were characterized by various analytical techniques, such as FTIR, DSC, TG, and WAXD. The results indicated that the crystallinity and melting temperature of the polymers decreased with increase in concentration of the BNOBN units in the polymer, the glass transition temperature of the polymers increased with increase in concentration of the BNOBN units in the polymer. Thermogravimetric studies showed that all the polymers were stable up to 536°C in N₂ atmosphere. The copolymers have good resistance to acidity, alkali, and organic solvents. Because of the melting temperature (T_m) depression with increase in the BNOBN content in the reaction system, the processability of the resultant coplymers could be effectively improved. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis of amphiphilic poly(phthalazinone ether sulfone ketone)‐graft‐poly(ethylene glycol) graft copolymers via Williamson etherification

Amphiphilic graft copolymers consisting of poly(phthalazinone ether sulfone ketone) (PPESK) backbones and poly(ethylene glycol) (PEG) side chains were synthesized via reaction of chloromethylated PPESK (CMPPESK) with a sodium alkoxide of methoxyl PEG (PEG‐ ONa). The reactive precursor, CMPPESK, was prepared by the chloromethylation of PPESK with chloromethylether (CME) using concentrated H₂SO₄ as reaction medium. FTIR spectroscopy, ¹H‐NMR and Solid‐state ¹³C CP‐MAS NMR analysis confirmed the covalent linking of PEG with PPESK backbones. The PEG content in the graft copolymers from ¹H‐NMR analysis varied from 21.0 to 37.2 wt %, which was approximately in agreement with that calculated from TGA tests. The graft products have good solubility in many aprotic polar solvents and can be slightly swelled by water and ethanol, but water insoluble. Contact angle measurements revealed that the hydrophilicity of PPESK was significantly improved by the introduction of PEG graft chains, indicating the graft copolymer is a potential hydrophilic additive for PPESK membranes. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007.     

Studies on water-swellable elastomers. II. Thermal properties and crystalline behavior of amphiphilic graft copolymers with poly(ethylene glycol) side chains

The thermal properties and crystalline structure of the amphiphilic graft copolymers CR-g-PEG600, CR-g-PEG2000, and CR-g-PEG6000 using chloroprene rubber (CR) as the hydrophobic backbone and poly (ethylene glycol) (PEG) with different molecular weights as the hydrophilic side chains were studied by DSC and WAXD. The results showed that a distinct phase-separated structure existed in CR-g-PEGs because of the incompatibility between the backbone segments and the side-chain segments. For all the polymers studied, T_m2, which is the melting point of PEG crystalline domains in CR-g-PEG, decreased compared to that of the corresponding pure PEG and varied little with PEG content. For CR-g-PEG600 and CR-g-PEG2000, T_m1, which is the melting point of the CR crystalline domains, increased with increasing PEG content when the PEG content was not high enough, and at constant PEG content, the longer were the PEG side chains the higher was the T_m1. The crystallite size L_o11 of CR in CR-g-PEGs increased compared to that of the pure CR and decreased with increasing PEG content. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 2441–2447, 1997