Polymer blends of carboxylated butadiene‐acrylonitrile copolymer (nitrile rubber) and polyamide 6 developed in twin screw extrusion

Polymer blends of carboxylated butadiene‐acrylonitrile copolymer (nitrile rubber) and polyamide 6 (PA6) were developed in twin screw extrusion. The rubber was cured with SP 1045 methylol phenolic resin during melt mixing in twin screw. Effect of degree of carboxylation in the rubber phase on blend properties has been assessed. Phase morphologies have been characterized using transmission electron microscopy. A compatibilizing NBR‐g‐Nylon 6 graft copolymer generated in situ during melt mixing via interfacial reaction between the ? COOH groups in NBR and the ? NH₂ end groups in nylon 6 has been effective in generating a fine and stable dispersion of the rubber within the polyamide matrix. The graft copolymer has been characterized by DMTA. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 372–377, 2007     

Effect of NBR on epoxy/glass prepregs properties

Solid acrylonitrile‐butadiene rubber (NBR) was used in epoxy resin for toughening and also for increasing the tack of epoxy/glass prepregs. The NBR used in this study was a rubber with 33% acrylonitrile content. The changes in thermal and mechanical properties such as glass transition temperature (T_g), curing characteristics and lap‐shear strength have been studied. For this purpose, three types of prepregs with two levels of NBR content of 3 and 5%, were prepared. Prepregs were made by solvent type impregnation apparatus. In this method, resin impregnates satin textile glass fiber under the controlled and constant condition of line speed and oven temperature. Prepregs were B‐staged for about 3%. The cure characterization, T_g and flow behavior were evaluated using differential scanning calorimetry and rheological analysis. Results showed that increasing the rubber content caused the following effects: (a) delay in gel time of prepregs, (b) increase in activation energy of prepregs, and (c) decrease in total heat of curing reaction. It is interesting that NBR increased the tack of epoxy/glass prepreg but, had no effect on its resin flow behavior. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

In situ preparation of magnesium methacrylate to reinforce NBR

Magnesium methacrylate (MDMA) was in situ prepared in nitrile rubber (NBR) by reacting magnesium hydroxide (Mg (OH)₂) with methacrylic acid (MAA) during the mixing step. The formation of MDMA in NBR was proved by the wide‐angle X‐ray diffraction analysis (WAXD). The mechanical properties, crosslinking structure, and morphology of the resulting peroxide‐cured NBR vulcanizates were studied. Results showed that Mg (OH)₂/MAA mixtures had a great reinforcing effect for NBR, and their amounts and ratio played important roles in influencing the ultimate properties. Both the covalent crosslink density and ionic crosslink density of the vulcanizates were measured. And the nano‐composite morphology of such vulcanizates was also observed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1403–1408, 2002; DOI 10.1002/app.10323     

Properties and morphologies of elastomer blends modified with EPDM‐g‐poly[2‐dimethylamino ethylmethacrylate]

The graft copolymerization of 2‐dimethylamino ethylmethacrylate (DMAEMA) onto ethylene propylene diene mononer rubber (EPDM) was carried out in toluene via solution polymerization technique at 70°C, using dibenzoyl peroxide as initiator. The synthesized EPDM rubber grafted with poly[DMAEMA] (EPDM‐g‐PDMAEMA) was characterized with ¹H‐NMR spectroscopy, gel permeation chromatography (GPC), differential scanning calorimetry (DSC), and thermal gravimetric analysis (TGA). The EPDM‐g‐PDMAEMA was incorporated into EPDM/butadiene acrylonitrile rubber (EPDM/NBR) blend with different blend ratios, where the homogeneity of such blends was examined with scanning electron microscopy and DSC. The scanning electron micrographs illustrate improvement of the morphology of EPDM/NBR rubber blends as a result of incorporation of EPDM‐g‐PDMAEMA onto that blend. The DSC trace exhibits one glass transition temperature (T_g) for EPDM/NBR blend containing EPDM‐g‐PDMAEMA, indicating improvement of homogeneity. The physico‐mechanical properties after and before accelerated thermal aging of the homogeneous, and inhomogeneous EPDM/NBR vulcanizates with different blend ratios were investigated. The physico‐mechanical properties of all blend vulcanizates were improved after and before accelerated thermal aging, in presence of EPDM‐g‐PDMAEMA. Of all blend ratios under investigation EPDM/NBR (75/25) blend possesses the best physico‐mechanical properties together with the best (least) swelling (%) in brake fluid. Swelling behavior of the rubber blend vulcanizates in motor oil and toluene was also investigated. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effects of small molecule plasticizer on the coordination crosslinking reaction between acrylonitrile‐butadiene rubber and copper sulfate

The effects of small molecule plasticizer of liquid acrylonitrile‐butadiene rubber (LNBR) on coordination crosslinking reaction between acrylonitrile‐butadiene rubber (NBR) and copper sulfate (CuSO₄) were investigated. Attenuated total reflectance infrared (ATR‐IR), curing curves analysis, equilibrium swelling method, differential scanning calorimetry (DSC), tensile test, and scanning electron microscope (SEM) were used in this work. The ATR‐IR analysis showed that the peak of restricted  CN is more explicit in NBR/CuSO₄/LNBR system. The curing curve analysis showed that NBR/CuSO₄/LNBR has higher torque. The results of equilibrium swelling method and DSC displayed that NBR/CuSO₄/LNBR has higher crosslink density and glass transition temperature, respectively. And NBR/CuSO₄/LNBR has stronger tensile strength and longer elongation at break from tensile test. SEM revealed the reasons that the NBR/CuSO₄/LNBR has better mechanical properties. All the results showed that addition of an amount of LNBR to NBR/CuSO₄ system could accelerate the coordination crosslinking reaction between NBR and CuSO₄. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Improvement of the homogeneity of SBR/NBR blends using polyglycidylmethacrylate‐g‐butadiene rubber

Polyglycidylmethacrylate grafted butadiene rubber (PGMA‐g‐BR) was synthesized by a graft solution copolymerization technique. The PGMA content was determined through titration against HBr. The PGMA‐g‐BR was blended with styrene butadiene rubber/butadiene acrylonitrile rubber (SBR/NBR) blends with different blend ratios. The SBR/NBR (50/50) blend was selected to examine the compatibility of such blends. Compatibility was examined using scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and viscosity measurements. The scanning electron micrographs illustrate the change of morphology of the SBR/NBR rubber blend as a result of the incorporation of PGMA‐g‐BR onto that blend. The T_gs of SBR and NBR in the blend get closer upon incorporation of PGMA‐g‐BR 10 phr, which indicates improvement in blend homogeneity. The intrinsic viscosity (η) versus blend ratio graph shows a straight‐line relationship, indicating some degree of compatibility. Thermal stability of the compatibilized and uncompatibilized rubber blend vulcanizates was investigated by determination of the physicomechanical properties before and after accelerated thermal aging. Of all the vulcanizates with different blend ratios under investigation, the SBR/NBR (25/75) compatibilized blend possessed the best thermal stability. However, the SBR/NBR (75/25) compatibilized blend possessed the best swelling performance in brake fluid. The effect of various combinations of inorganic fillers on the physicomechanical properties of that blend, before and after accelerated thermal aging, was studied in the presence and absence of PGMA‐g‐BR. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1559–1567, 2006     

Composites based on CB/CF/Ag filled EPDM/NBR rubber blends with high conductivity

For many applications of conductive rubbers, it is desirable to endow the conductive rubber with high conductivity at low conductive filler loading. In this work, composites based on ethylene‐propylene‐diene monomer (EPDM) rubber and nitrile‐butadiene rubber (NBR) were prepared using carbon blacks, carbon fibers, and silver powders as fillers. As the weight fraction of silver powder increased, the hardness of composites increased gradually while the tensile strength and elongation at break decreased. SEM revealed that the EPDM/NBR blends exhibited a relatively co‐continuous morphology. The differential scanning calorimetry (DSC) curves reported the EPDM/NBR rubber blends were incompatibility. The thermogravimetry (TG) studies showed that adding a small amount of silver powder could improve the thermal stability of composites. These conductive composites exhibited good electrical property. At room temperature, when the total volume fraction of fillers was 15.20%, the volume resistivity of EPDM/NBR blend was only 0.0058 Ω cm. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41357.     

The Miscibility of Novel Bisphenol-Propylene Epoxy Resin With Liquid NBR

A novel kind of bisphenol-type epoxy resin with a vinyl side-chain was developed and its miscibility behavior with liquid nitrile-butadiene rubber (NBR) was investigated. The diglycidyl ether of bisphenol propylene (DGEBP) was prepared by the condensation of phenol with acrolein in the presence of an acid catalyst and the subsequent epoxidization with epichlorohydrin (ECH). The structures of the bisphenol and corresponding epoxy resin were characterized by infrared (IR) and nuclear magnetic resonance (NMR) spectral analyses and the epoxy value was determined to be 0.34 mol/100 g by titration. The mixture of DGEBP with the liquid NBR containing diglycidyl ether of bisphenol acetone (DGEBA) was prepared and cured with diaminodiphenylmethane (DDM). The miscibility and morphology of the mixture system were studied by dynamic mechanical thermal analysis (DMTA) and transmission electron microscopy (TEM), respectively. The cured mixture of DGEBP/NBR/DDM exhibited good miscibility and, therefore, no separation, along with a transparent appearance at rubber contents of 10 wt% and 30 wt%. For cured DGEBP/DGEBA/NBR/DDM systems at 20 wt% rubber content, the dispersed rubber phase and rubber particles were not observed by DMTA or TEM at DGEBP content above 40 wt%. The DMTA plot showed a single peak related to the glass transition temperature (T _g) which decreased with increasing DGEBP content. The appearance of the system varied from transparent to opaque and the rubber separated from the epoxy matrix to form two phases when the DGEBP content decreased. The T _g values of the rubber- and epoxy-rich phases were strongly dependent on the DGEBP content in the mixed system. The miscibility of epoxy resin with liquid NBR can be altered by varying the ratio of DGEBP to DGEBA.     

Preparation and characterization of polymethyltrifluoropropylsilicone modified acrylonitrile–butadiene rubber/fluorosilicon rubber blend

The blending of polymethyltrifluoropropylsilicone‐modified acrylonitrile–butadiene rubber (MNBR) and fluorosilicon rubber (FSR) at 70 : 30 ratio was investigated. The grafting of mercapto‐functionalized polymethyltrifluoropropylsilicone onto acrylonitrile‐butadiene rubber (NBR) by thiol‐ene reaction was carried out with 2,2′‐azobisisobutyronitrile as initiator in a Haake torque rheometer. The rheological properties of NBR grafting obtained at varying dosages of polymethyltrifluoropropylsilicone in a Haake torque rheometer were studied using torque curves. Grafting reaction was confirmed by ¹H nuclear magnetic resonance and energy‐dispersive X‐ray spectroscopy. Results of scanning electron microscopy and dynamic mechanical analysis showed better compatibility of MNBR/FSR blend than NBR/FSR reference blend. Meanwhile, the macro‐mechanical properties of the blend significantly improved. The tensile strength and tear strength of MNBR/FSR blend were improved to 14.34 MPa and 44.94 KN/m, respectively, which were 2.92 MPa and 13.03 KN/m higher than those of NBR/FSR reference blend. The low‐temperature brittleness of the blend was improved to ?57°C, an increase of ?6°C compared with that of NBR. These results indicated that MNBR/FSR blend at 70 : 30 ratio had improved compatibility because of the grafting chains that acted as interfacial agents. The low‐temperature resistance of the blend was also enhanced. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42328.     

New method for hydrogenating NBR latex

A new hydrogenation system consisting of hydrazine hydrate and sodium periodate has been developed for hydrogenation of nitrile‐butadiene rubber (NBR) latex by diimide reduction technique. The optimization of the reaction conditions was obtained. The influences of the concentration of reactants, reaction time, and temperature on hydrogenation degree were investigated. The results indicated that hydrogenation degree of the product (HNBR) can be extended to 95% through this new method. In addition, ¹H‐NMR and infrared spectra confirmed that C?C double bonds in NBR were successfully hydrogenated without reduction of the CN group. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Dual Band Resonance in Tetragonal BaTiO3/NBR Composites for Microwave Absorption Applications

Tetragonal BaTiO₃ bulk samples are prepared using the solid‐state route in conjunction with intermediate high‐temperature annealing steps. The (002) and (200) X‐ray diffraction peaks near 2?~45° and 310, 520, and 720 cm^?1 characteristic vibrational modes in Raman spectroscopic measurements confirm the tetragonal crystallographic structure of BaTIO₃ bulk samples. The 1100°C annealed BaTiO₃ sample showed optimal tetragonality ~1.016 and the same is used for BaTiO₃–acrylonitrile butadiene rubber (NBR) composites at different BaTiO₃ loading fractions in parts per hundred (PHR). These BaTiO₃/NBR composite systems exhibit dual band microwave resonance, widening the operating window for microwave absorption applications. Eighty PHR BaTiO₃/NBR composite exhibits microwave reflection losses (RL) at 9.5 and 16.5 GHz with ~?9 and ~?18 dB reflection losses, respectively. The onset of dual band is attributed to the ferroelectric‐induced dipolar relaxation at 9.5 GHz and its second‐order resonance at 16.5 GHz in such composite systems.     

The physical properties of carbon nanoparticles dispersed into NBR/LLDPE nanocomposites for corrosion protection applications

In this study, novel acrylonitrile butadiene rubber (NBR) nanocomposites with improved electrical conductivity and mechanical properties were synthesized. Carbon nanoparticles (CNP)/NBR composites and CNP‐polyethylene/NBR nanocomposites were prepared by mixing via two‐roll mill. The first type of the nanocomposite was produced to determine the percolation threshold concentration (V_c). The second type with constant CNP concentration, slightly over V_c (0.2 vol %), was synthesized to investigate the influence of polyethylene content on the mechanical, electrical and swelling behavior of nanocomposites. Only the nanocomposites with 3 vol % polyethylene loading showed electrical conductivity. However, the composites with higher polyethylene loadings showed insulating behavior due to hindrance of CNP network by polyethylene layers. Swelling measurements revealed that the change in entropy of the swelling increased with the increase in disorder level but decreased with the increase in intercalation level of CNP in the disordered intercalated nanocomposite. The increase in solvent uptake was comparable with the free volume in NBR matrix upon inclusion of nanoparticles, whereas the inhibition in solvent uptake for higher polyethylene loading was described by bridging flocculation. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synergistic reinforcement of NBR by hybrid filler system including organoclay and nano‐CaCO3

Rubber nanocomposites containing one type of nanofiller are common and are widely established in the research field. In this study, nitrile rubber (NBR) based ternary nanocomposites containing modified silicate (Cloisite 30B) and also nano‐calcium carbonate (nano‐CaCO₃) were prepared using a laboratory internal mixer (simple melt mixing). Effects of the hybrid filler system (filler phase have two kind of fillers) on the cure rheometry, morphology, swelling, and mechanical and dynamic–mechanical properties of the NBR were investigated. Concentration of nano‐CaCO₃ [0, 5, 10, and 15 parts per one hundred parts of rubber by weight (phr)] and organoclay (0, 3, and 6 phr) in NBR was varied. The microstructure and homogeneity of the compounds were confirmed by studying the dispersion of nanoparticles in NBR via X‐ray diffraction and field emission scanning electron microscopy. Based on the results of morphology and mechanical properties, the dual‐filler phase nanocomposites (hybrid nanocomposite) have higher performance in comparison with single‐filler phase nanocomposites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42744.     

Devulcanization of nitrile butadiene rubber in nitrobenzene

Sulfur‐crosslinked nitrile butadiene rubber (s‐NBR) was found to be devulcanized when it was heated with nitrobenzene at 200°C for 3 h. The tetrahydrofuran (THF)‐soluble fraction from s‐NBR heated with nitrobenzene was purified by reprecipitation with THF/n‐hexane, chloroform/n‐hexane, and THF/n‐hexane systems and was then characterized by means of Fourier transform infrared (FTIR) spectroscopy, ¹H‐NMR, gel permeation chromatography, dynamic thermogravimetry/differential thermal analysis (DTA), and differential scanning calorimetry (DSC). FTIR and ¹H‐NMR results revealed that the THF‐soluble fraction contained aromatic rings derived from nitrobenzene. Furthermore, the molecular weight of the THF‐soluble fraction was much lower than that of the parent noncrosslinked poly(acrylonitrile‐co‐butadiene). Although the weight loss of THF‐soluble fraction began at a lower temperature than that of the nonheated original nitrile butadiene rubber, the residual weight at 700°C tended to be higher for the former. This tendency became more marked with increasing time of heat treatment with nitrobenzene. The DSC‐determined glass‐transition temperature of the THF‐soluble fraction was higher than that of the original s‐NBR. To elucidate the devulcanization mechanism, we investigated two types of model reactions; one was the reaction of diphenyl disulfide with nitrobenzene, and the other was the reaction of polybutadiene with nitrobenzene. The former reaction, carried out at 250°C in diphenyl ether, yielded diphenyl sulfide with a loss of diphenyl disulfide and nitrobenzene. The use of a higher molar ratio of nitrobenzene to diphenyl disulfide resulted in a depression of diphenyl sulfide formation. The reaction of p‐chloronitrobenzene with diphenyl disulfide also gave diphenyl sulfide. The reaction of polybutadiene with nitrobenzene at 200°C resulted in the backbone scission of the polymer. The THF‐soluble solid product of the latter model reaction was found by FTIR and ¹H‐NMR to contain aromatic rings derived from nitrobenzene. The devulcanization mechanism is discussed on the basis of a comparison of the results of the model reactions with those of the s‐NBR devulcanization. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3342–3353, 2004     

Wood flour: A new filler for the rubber processing industry. I. Cure characteristics and mechanical properties of wood flour‐filled NBR and NBR/PVC compounds

In this study, conifer wood flour was evaluated as a filler to NBR or NBR/PVC compounds studying it influence on their cure characteristics and mechanical properties. It was shown that the filling by wood flour offers a possibility to obtain high modulus high elastic or less elastic or rigid wood like vulcanizates by varying of both the filling level and NBR/PVC mass ratio.It was established that in contrary to the mineral fillers usually causing significant delay of the vulcanization process, the wood flour shows a tendency to reduce the optimum cure time, τ₉₀. Modulus M₁₀₀ and Shore hardness of the wood flour‐filled vulcanizates of NBR or NBR/PVC compounds in which NBR is predominant, increase in a compliance with the increase of M_max and DM when the filling level increases. The dependence is other when NBR and PVC are in equal amounts or PVC predominates. As a most probable explanation of the effect of the wood flour on the cure characteristics is accepted, the influence of the wood flour polar groups as well as of the presenting as wood flour humidity water molecules, the specific mechanical properties of the wood flour‐filled NBR or NBR/PVC compounds could be connected (to some extend) with a specific interface interaction between the wood flour particles and the polymer matrix. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2734–2739, 2003     

Influence of curing agent and compatibilizer on the physicomechanical properties of polypropylene/nitrile butadiene rubber blends investigated by positron annihilation lifetime technique

A series of thermoplastic vulcanizates of polypropylene (PP)/nitrile butadiene rubber (NBR) (50/50) have been prepared by melt‐mixing method, using phenolic resin/SnCl₂ as the curing system and maleic anhydride‐functionalized PP (PP‐g‐MA) and carboxylated NBR (NBRE‐RCOOH) as the compatibilizing system. Triethylenetetramine was also employed to promote the reaction between the functionalized polymers. The effects of curing agent and compatibilizer on the mechanical and morphological properties have been studied. A novel technique based on positron annihilation lifetime spectroscopy has been used to measure the free volume parameters of these systems. The positron results showed minimum free volume size and free volume fraction at 5.0% of the curing agent suggesting some crosslinking in the rubber phase. The reduction in free volume holes at 2.5% of the compatibilizer is interpreted as improvement in the interfacial adhesion between the components of the blend. The observed variation of free volume fraction is opposite to the tensile strength and exhibits the correlation that, lesser the free volume more is the tensile strength at 2.5% of the compatibilizer in the blend. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4672–4681, 2006     

In situ preparation of zinc salts of unsaturated carboxylic acids to reinforce NBR

Through the neutralization reaction of zinc oxide (ZnO) and methacrylic acid (MAA) or acrylic acid (AA), zinc methacrylate (ZMA) or zinc acrylate (ZA) was in situ prepared in nitrile rubber (NBR). The mechanical properties and crosslinking structure of the resulting peroxide‐cured NBR vulcanizates were studied. The results showed that ZnO/MAA (AA) had a great reinforcing effect for NBR, and their amounts and ratio played important roles in influencing the mechanical properties. Such vulcanizate contains both covalent crosslinks and salt crosslinks, and the change in the tensile strength of the vulcanizate was related to the variation of the salt crosslink density. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2740–2748, 2000     

The Effect of Epoxidized Sunflower Oil on the Miscibility of Plasticized PVC/NBR Blends

Blends of plasticized poly(vinyl chloride) (PVC) with several ratios of nitrile rubber (NBR) were studied. The effects of epoxidized sunflower oil (ESO) in combination with di-(2-ethylhexyl)phthalate (DEHP) in the PVC blends on the tensile strength, elongation, hardness, and dynamical mechanical analysis (DMA) were studied. The modulus and hardness results revealed that the addition of ESO to the blend favors the miscibility of PVC and NBR. The PVC/NBR/(DEHP-ESO) blends behave as a compatible system as is evident from the single T _g observed in DMA. The moderate level broadening of the T _g zone in blends is due to the presence of ESO in the plasticizer system. Blends of plasticized PVC and nitrile rubber showed promising properties. The ESO is suitable to partially replace DEHP in PVC/NBR blends.     

Effect of different coagents on physico‐chemical properties of electron beam cured NBR/HDPE composites reinforced with HAF carbon black

The effect of different coagents on the physico‐chemical properties of NBR/HDPE composites reinforced with 40 phr (part per hundred part of rubber by weight) HAF carbon black and cured with accelerated electrons was investigated. The coagents N,N′‐methylene bisacrylamide (MBAAm) and trimethylol propane trimethacrylate (TMPTMA) were used at a constant content of 10 phr. The physico‐chemical properties such as tensile strength, tensile modulus at 50% elongation (M₅₀), elongation at break (E_b), hardness, soluble fraction (SF), swelling number (SN), electrical conductivity, and thermal properties were studied. The results obtained showed that the TMPTMA as a coagent is more effective than MDA in enhancing the mechanical and physical properties of NBR/HDPE vulcanized composites. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Synthesis,characterization, and evaluation of natural rubber‐graft‐N‐(4‐aminodiphenyl methane) acrylamide as an antioxidant

The synthesis of N‐(4‐aminodiphenylmethane) acrylamide (ADPMA) was performed through the reaction of 4,4′‐diaminodiphenyl methane and acryloyl chloride in the presence of triethyl amine. The grafting of ADPMA onto natural rubber was executed with UV radiation. Benzoyl peroxide was used to initiate the free‐radical grafting copolymerization. Natural rubber‐graft‐N‐(4‐aminodiphenyl methane) acrylamide (NR‐g‐ADPMA) was characterized with an IR technique. We studied the effect of aging on the mechanical properties and the swelling and extraction phenomena for acrylonitrile–butadiene copolymer (NBR) vulcanizates, which contained the prepared NR‐g‐ADPMA and a commercial antioxidant, N‐isopropyl‐N′‐phenyl‐p‐phenylenediamine. The prepared antioxidant enhanced both the mechanical properties of the NBR vulcanizates and the permanence of the ingredients in these vulcanizates. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 843–849, 2006