Mechanical properties and morphology of nylon‐6 hybrid composites

In this investigation, the influence of filler type and filler content on the mechanical properties of nylon‐6 is investigated. The mineral fillers were selected on the basis of their shape and size: flake‐like kaolin and talc, spherical glass beads or fibrous wollastonite. These fillers were added to nylon‐6 individually or in mixed combinations. They were added at different percentages varying between 10 and 30% w/w. Samples of the composites were prepared by the injection moulding process. Uniaxial tensile, Izod impact and flexural tests were carried out. Tensile strength, elongation at break, modulus of elasticity and impact energy were obtained and compared. In case of single fillers the results showed that the tensile strength, modulus of elasticity and their flexural values for nylon‐6 composite improve with the increase in filler content while mixed compounds showed no significant changes above 15% + 15% w/w filler. However, for single and mixed filler up to 10% w/w, the impact strength and maximum elongation at break showed significant decrease. In general, the maximum improvement in mechanical the addition of 10–15% w/w filler. Copyright © 2003 Society of Chemical Industry     

Physical–mechanical properties and morphological study on nylon‐6 recycling by injection molding

The effect of the multiple recycling of nylon‐6 by injection molding on its physical–mechanical properties and morphology was studied after each cycle of injection. These studies were made in order to know how many times it is possible to recycle the nylon‐6 without significant loss of the physical–mechanical properties. Optical and electronic microscopy were used to evaluated the morphology. Molecular weight changes were determinated by gel permeation chromatography (GPC). The nylon‐6 was recycled 10 times, until the eighth cycle the properties of the material did not suffered any change. Changes of 10–15% in the properties between nylon‐6 with 10 cycles of injection and virgin material were observed. An exception was the percentage of elongation that decreased 70% gradually until in the tenth cycle of injection. The results from GPC show that the molecular weight of nylon‐6 increased with recycling (M_w = 17% and M_n = 14%). With the reprocess was also observed the presence of gels. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 851–858, 2000     

Preparation of conductive polyaniline/nylon‐6 composite films by polymerization of aniline in nylon‐6 matrix

Polyaniline (PANI)/Nylon‐6 composite films were prepared by oxidative polymerization of aniline (ANI) inside host Nylon‐6 film. Such a composite has the desired electro‐active and mechanical properties to serve as a self‐standing functional unit. Comparative studies on sorption of ANI by Nylon‐6 matrix from various ANI containing media were conducted revealing superior ANI uptake from neutral ANI solution in water. ANI content was measured to be as high as 12%. Spectroscopic measurements showed that hydrogen bonding seemed to play important role in ANI sorption by Nylon‐6 matrix. Polymerization was monitored using atomic force microscopy and conductivity measurements. The morphology studies showed the appearance of PANI nanodomains on Nylon‐6 surface in the early stages of the polymerization. Eventually the domains coalesced during polymerization forming a continuous PANI layer. The conductivity measurements confirmed the change of the morphology from isolated islands to continuous conducting surface by drastic increase in conductivity. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Influence of grafting on structural and optical properties of nylon‐6 fibers

This study throws light on the change of the optical properties and some structural properties due to graft copolymerization of polydiallyldimethyl ammonium chloride (PDADMAC) and polyacrylamide (PAA) of nylon‐6 fibers. Multiple‐beam interferometric technique in transmission was used to study the change of the diameter, refractive indices, and birefringence of nylon‐6 fibers at different graft yields. The results were utilized to investigate the isotropic refractive index, the mean polarizabilities per unit volume, dielectric constant, dielectric susceptibility, and surface reflectivity for nylon‐6 and grafted nylon‐6 fiber. The effect of grafted PAA onto modified nylon‐6 fibers containing PDADMAC on the crystallinity was studied by X‐ray diffraction. These results reflect good effect of grafting on the optical and structural properties of nylon‐6 fibers. The opto‐thermal properties of grafted PAA with different graft yields have been studied. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Crystallization and melting behavior of multi‐walled carbon nanotube‐reinforced nylon‐6 composites

The crystallization and melting behavior of neat nylon‐6 (PA6) and multi‐walled carbon nanotubes (MWNTs)/PA6 composites prepared by simple melt‐compounding was comparatively studied. Differential scanning calorimetry (DSC) results show two crystallization exotherms (T_{CC, 1} and T_{CC, 2}) for PA6/MWNTs composites instead of a single exotherm (T_{CC, 1}) for the neat matrix. The formation of the higher‐temperature exotherm T_{CC, 2} is closely related to the addition of MWNTs. X‐ray diffraction (XRD) results indicate that only the α‐phase crystalline structure is formed upon incorporating MWNTs into PA6 matrix, independently of the cooling rate and annealing conditions. These observations are significantly different from those for PA6 matrix, where the increase in cooling rate or decrease in annealing temperature results in the crystal transformation from α‐phase to γ‐phase. The crystallization behavior of PA6/MWNTs composites is also significantly different from those reported in PA6/nanoclay systems, probably due to the difference in nanofiller geometry between one‐dimensional MWNTs and two‐dimensional nanoclay platelets. The nucleation sites provided by carbon nanotubes seem to be favorable to the formation of thermodynamically stable α‐phase crystals of PA6. The dominant α‐phase crystals in PA6/MWNTs composites may play an important role in the remarkable enhancement of mechanical properties. Copyright © 2005 Society of Chemical Industry     

Effect of an epoxy‐based bonding agent on the cure characteristics and mechanical properties of short‐nylon‐fiber‐reinforced acrylonitrile–butadiene rubber composites

The cure characteristics and mechanical properties of short‐nylon‐fiber‐reinforced acrylonitrile–butadiene rubber composites with and without an epoxy resin as a bonding agent were studied. The epoxy resin was a good interfacial‐bonding agent for this composite system. The minimum torque showed a marginal increase with the resin concentration. The maximum–minimum torque showed only a marginal change with the resin. The scorch time decreased with the fiber concentration and resin content. The tensile strength and abrasion resistance were improved and the tear resistance and resilience were reduced with the resin concentration. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 532–539, 2006     

Structure and property study of nylon‐6/clay nanocomposite fiber

The crystal structures of nylon‐6 and nylon‐6/clay fibers were investigated on annealing and drawing. Annealing increased the γ‐crystalline form of both fibers, as indicated by the DSC curves, and its effect was dominant in nylon‐6/clay fiber. On drawing, the γ‐crystalline form was easily converted into the α form in nylon‐6, whereas it was still observed at a relatively high spin‐draw ratio in nylon‐6/clay fiber. However, although the α‐crystal form was dominant in nylon‐6, the γ‐crystal form was dominant in nylon‐6/clay with annealing and drawing, on the basis of the XRD data. The fast crystallization rate of nylon‐6/clay compared with pure nylon‐6 was confirmed, on the basis of the Avrami exponent. The initial modulus of nylon‐6/clay fiber was 30 % higher than the neat nylon‐6 fiber. The reinforcing effect of clay on the dynamic storage modulus was observed. Copyright © 2004 Society of Chemical Industry     

Mechanical and thermal properties of glass bead–filled nylon‐6

The mechanical and thermal properties of glass bead–filled nylon‐6 were studied by dynamic mechanical analysis (DMA), tensile testing, Izod impact, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC) tests. DMA results showed that the incorporation of glass beads could lead to a substantial increase of the glass‐transition temperature (T_g) of the blend, indicating that there existed strong interaction between glass beads and the nylon‐6 matrix. Results of further calculation revealed that the average interaction between glass beads and the nylon‐6 matrix deceased with increasing glass bead content as a result of the coalescence of glass beads. This conclusion was supported by SEM observations. Impact testing revealed that the notch Izod impact strength of nylon‐6/glass bead blends substantially decreased with increasing glass bead content. Moreover, static tensile measurements implied that the Young's modulus of the nylon‐6/glass bead blends increased considerably, whereas the tensile strength clearly decreased with increasing glass bead content. Finally, TGA and DSC measurements indicated that the thermal stability of the blend was obviously improved by incorporation of glass beads, whereas the melting behavior of the nylon‐6 remained relatively unchanged with increasing glass bead content. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1885–1890, 2004     

Friction and wear studies on nylon‐6/SiO2 nanocomposites

Composites of nanometer‐sized silica (SiO₂) filler incorporated in nylon‐6 polymer were prepared by compression molding. Their friction and wear properties were investigated on a pin on disk tribometer by running a flat pin of steel against a composite disc. The morphologies of the composites as well as of the wear track were observed by scanning electron microscopy (SEM). The addition of 2 wt % SiO₂ resulted in a friction reduction (μ) from 0.5 to 0.18 when compared with neat nylon‐6. This low silica loading led to a reduction in wear rate by a factor of 140, whereas the influence of higher silica loadings was less pronounced. The smooth morphology obtained after the wear test indicated the negligible contribution to friction of the pin to the nanocomposite. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1855–1862, 2004     

γ‐Irradiated poly(tetrafluoroethylene) particle‐filled low‐density polyethylene. I. Effect of silane coupling agents on mechanical,thermal, and morphological properties

Poly(tetrafluoroethylene) (PTFE) scraps were recovered as a filler material for low‐density polyethylene (LDPE) after they were degraded by Co‐60 γ‐rays under atmospheric conditions to make small‐size powder. The powder PTFE, which was called secondary PTFE (2°‐PTFE), was melt mixed with LDPE and then extruded to obtain 200 µm films. The mechanical and thermal properties and also the morphology of the fractured surface of these 2°‐PTFE–filled LDPE were studied. It was found that the addition of 2°‐PTFE resulted in thermofilm property of LDPE but it slightly decreased the thermal oxidative temperature of LDPE. The tensile strength and ultimate elongation of LDPE were found to decrease with the addition of 2°‐PTFE. However, when it is compared to the addition of virgin PTFE into LDPE, 2°‐PTFE shows better mechanical properties due to the presence of oxy groups which are capable of interacting with the main matrix. A further improvement in mechanical properties was achieved by silane coupling agent treatment of 2°‐PTFE. Silane coupling agents were found to enhance the interfacial adhesion between 2°‐PTFE and LDPE. The study on the fractured surfaces by scanning electron microscope revealed this adhesion between these two polymers. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 866–876, 1999     

Effect of titanate coupling agent on the mechanical,thermal, dielectric,rheological, and morphological properties of filled nylon 6

Fillers are used along with various commodity as well as engineering polymers to improve the properties of polymers. The performance of filled polymers is generally decided on the basis of the interface attraction of filler and polymers. Fillers of widely varying particle size and surface characteristics are responsive to the interfacial interactions with polymers. The present study deals with the effect of a coupling agent, tetra isopropyl titanate (TPT), on the properties of flyash filled nylon 6. It is observed that tensile strength, impact strength, and heat distortion temperature improved with the addition of TPT as compared to without the coupling agent filled nylon 6. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 266–272, 2006     

Kinetics of the solid‐state polymerization of nylon‐6

The kinetics of the thermally induced solid‐state polymerization (SSP) of nylon‐6 were examined in both a fixed‐bed reactor and a rotary reactor. Factors such as the regulator content, the reaction temperature and time, the particle size, the type and geometry of the nylon‐6 prepolymer, the nitrogen gas flow rate, the water content of the nitrogen gas flow, and the polymerization process were studied. The results showed that the regulator content, the reaction temperature and time, and the particle size were the primary factors, and that the others were negligible. Moreover, the SSP rate and number‐average molecular weight (M_n) increased with increasing reaction temperature and time and decreasing particle size. The SSP rate and M_n had maximum values with increasing regulator content in an experimental range of 0.03–0.07 wt %. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 616–621, 2002; DOI 10.1002/app.10341     

尼龙6改性研究

采用经化学改性的芳纶纤维增强尼龙6,并通过红外光谱和电镜分析其界面层,结果表明芳纶纤维经异氰酸酯化及封端稳定处理后,其表面所接技的不稳定基团-NCO转化成稳定的-NHCO-,封端结果较为明显;改性后纤维表面附有接枝物,从而使表面粗糙程度大大增加。用挤出和注塑的方法加工了PA6／Kevlar纤维（KF）复合材料,研究了它的拉伸、弯曲和冲击性能破坏形态。力学性能测试表明了改性尼龙6复合材料的拉伸和弯曲强度得到了改善,但冲击性能略为下降。     

Cure characteristics and mechanical properties of short nylon fiber‐reinforced nitrile rubber composites

Acrylonitrile butadiene rubber (NBR)‐based composites were prepared by incorporating short nylon fibers of different lengths and concentration into the matrix using a two‐roll mixing mill according to a base formulation. The curing characteristics of the samples were studied. The influence of fiber length, loading, and rubber crosslinking systems on the properties of the composites was analyzed. Surface morphology of the composites has been studied using Scanning Electron Microscopy (SEM). Addition of nylon fiber to NBR offers good reinforcement, and causes improvement in mechanical properties. A fiber length of 6 mm was found to be optimum for the best balance of properties. It has been found that at higher fiber loadings, composites show brittle‐type behavior. Composites vulcanized by the dicumyl peroxide (DCP) system were found to have better mechanical properties than that by the sulfur system. The swelling behavior of the composites in N,N‐dimethyl formamide has been analyzed for the swelling coefficient values. Composites vulcanized in the DCP system were found to have higher rubber volume fraction than that in the sulfur system, which indicates better rubber–fiber interaction in the former. The crosslink densities of various composites were also compared. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1023–1030, 2004     

The effect of coupling agents on the mechanical and physical properties of oil palm empty fruit bunch–polypropylene composites

Oil palm empty fruit bunch–polypropylene (EFB‐PP) composites have been produced using a twin‐screw extruder as the compounding equipment. Two levels of EFB were employed, 40 % and 60 % of the total weight of the sample. Three types of coupling agent, maleic anhydride‐modified polypropylene (commercial name Epolene E‐43), polymethylene(polyphenyl isocyanate) (PMPPIC) and 3‐(trimethoxysilyl)‐propylmethacrylate (TPM), were used. Overall, all coupling agents imparted considerable improvements in the flexural properties, E‐43 showing the highest enhancement. However, only E‐43 was observed to improve impact strength and tensile properties of the composites. All composites with coupling agents showed lower water absorption and thickness swelling. The absorption and swelling decreased as the loading of the coupling agents was increased. © 2000 Society of Chemical Industry     

Interior synthesizing of ZnO nanoflakes inside nylon‐6 electrospun nanofibers

Doping of the polymeric electrospun nanofibers by metal oxides nanoparticles is usually performed by electrospinning of a colloidal solution containing the metal oxide nanoparticles. Besides the economical aspects, electrospinning of colloids is not efficient compared with spinning of sol–gels, moreover well attachment of the solid nanoparticles is not guaranteed. In this study, reduction of zinc acetate could be performed inside the nylon‐6 electrospun nanofibers; so polymeric nanofibers embedding ZnO nanoflakes were obtained. Typically, zinc acetate/nylon‐6 electrospun nanofibers were treated hydrothermally at 150°C for 1 h. Besides the utilized characterization techniques, PL study affirmed formation of ZnO. The produced nanofibers showed a good antibacterial activity which improves with increasing ZnO content. Overall, the present study opens new avenue to synthesize hybrid nanofibers by a facile procedure. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Rice husk/poly(propylene‐co‐ethylene) composites: Effect of different coupling agents on mechanical,thermal, and morphological properties

Poly(propylene‐co‐ethylene) composites with rice husk were prepared in a corotating intermeshing twin‐screw extruder using four different coupling agents. While modified maleic anhydrides such as maleated polypropylene (MAPP) and maleated polyethylene (MAPE) are commonly used as compatibilizers to improve interfacial adhesion between lignocellulosic filler and matrix, in this study, polypropylene grafted with acid comonomer (CAPP) and high‐density polyethylene grafted with acid comonomer (CAPE) were also used. The morphologies and the thermal and mechanical properties of the composites were characterized using scanning electron microscopy, thermogravimetric analysis, differential scanning analysis, tensile and impact tests. The results indicate that the base resin of the compatibilizer is an important factor in determining the effectiveness of compatibilizers for composites. Composites with PP‐based compatibilizers are more effective than PE‐based compatibilizers due to the improved wetting of the former compatibilizer in the matrix polymer. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Ternary reactive blends of nylon‐6 matrix with dispersed rigid brittle polymer and elastomer

Except by elastomers, the toughness of nylon‐6 (N‐6) can be improved by the addition of rigid poly(styrene‐co‐maleic anhydride) (SMA). In this case, strength and stiffness are also enhanced. Combination of SMA with maleated ethylene‐propylene rubber or styrene‐ethene/butene‐styrene with a total content below 15% gives a ternary blend having a toughness level close to elastomer toughening, whereas the strength and stiffness reached at least the Nylon‐6 values. An explanation is a synergistic combination of both elastomer and rigid polymer toughening mechanisms. An opposite effect on mechanical behavior was found with high contents of both additives. Except for worsened strength and stiffness, in some cases, a higher elastomer content even did not enhance the toughness. This effect can be explained by too fine phase structure found, causing the matrix ligament dimension to be below its minimum critical value. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1404–1411, 1999     

Opto‐thermal properties of fibers XVIII—Skin‐core structures variations in nylon 6 fibers due to different annealing conditions

Nylon 6 fibers (Amilan) were annealed at constant temperature 140 ± 1°C for different time durations (1–10 h). Refractive indices have been previously measured interferometerically. Two independent techniques were used to study the optical anisotropy and density in these fibers. The first was the application of a multiple‐beam to determine the skin and core “mean” refractive indices and birefringence of the samples. The technique used multiple‐beam Fizeau fringes in transmission. The second technique was an acoustic method for measuring the density of the investigated fibers. The optical results were used to calculate the optical orientation factors for skin and core. The values of (Δα/3α₀), which depend upon the molecular structure of the polymer, remain constant and in agreement with the previous published data. The density results were used to calculate the degree of crystallinity of nylon 6 fibers. In addition, the results were used to calculate the mean square density fluctuation, the harmonic mean polarizability of the dielectric, specific refractivity of the isotropic dielectric and the virtual refractive index. Also, the number of monomer units per unit volume, and n₁ and n₂, which are the refractive indices of fully oriented fiber, were calculated and found to be (1.606 and 1.534). Hermans optical orientation functions have been compared with the generalized Lorentz‐Lorenz equation given by de Vries. Microinterferograms and curves are given for illustration. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 3349–3360, 2001